Power management and power flow control with back-to-back converters in a utility connected microgrid

This paper proposes a method for power flow control between utility and microgrid through back-to-back converters, which facilitates desired real and reactive power flow between utility and microgrid. In the proposed control strategy, the system can run in two different modes depending on the power requirement in the microgrid. In mode-1, specified amount of real and reactive power are shared between the utility and the microgrid through the back-to-back converters. Mode-2 is invoked when the power that can be supplied by the DGs in the microgrid reaches its maximum limit. In such a case, the rest of the power demand of the microgrid has to be supplied by the utility. An arrangement between DGs in the microgrid is proposed to achieve load sharing in both grid connected and islanded modes. The back-to-back converters also provide total frequency isolation between the utility and the microgrid. It is shown that the voltage or frequency fluctuation in the utility side has no impact on voltage or power in microgrid side. Proper relay-breaker operation coordination is proposed during fault along with the blocking of the back-to-back converters for seamless resynchronization. Both impedance and motor type loads are considered to verify the system stability. The impact of dc side voltage fluctuation of the DGs and DG tripping on power sharing is also investigated. The efficacy of the proposed control ar-rangement has been validated through simulation for various operating conditions. The model of the microgrid power system is simulated in PSCAD.

Lateral distortional buckling design rules for back to back LiteSteel beams

A new cold-formed steel beam, known as the LiteSteel Beam (LSB), has the potential to transform the low-rise building industry. The new beam is effectively a channel section with two rectangular hollow flanges and a slender web, and is manufactured using a simultaneous cold-forming and electric resistance welding process. Research into the flexural behaviour of single LSB members showed that the LSBs are susceptible to lateral distortional buckling effects and their moment capacities are significantly reduced for intermediate spans. Build-up LSB sections are expected to improve their flexural capacity and to enhance their applications. They are also likely to mitigate the detrimental effects of lateral distortional buckling observed with single LSB members of intermediate spans. However, the behaviour of build up beams is not well understood. Currently available design rules were found to be inadequate to predict the member moment capacities of back to back LSBs. Therefore a research project based on both experimental and numerical studies was undertaken to investigate the flexural behaviour of back to back LSBs with various longitudinal connection spacings under a uniform moment. New design rules were developed using the moment capacity data obtained using finite element analyses and experimental tests. This paper presents the details of the development of design rules for the back to back LSB sections.

Strength improvement methods for back to back Litesteel beams

LiteSteel Beam (LSB) is a new cold-formed steel beam produced by OneSteel Australian Tube Mills (OATM). The new beam is effectively a channel section with two rectangular hollow flanges and a slender web, and is manufactured using patented dual electric resistance welding and automated roll-forming technologies. OATM is promoting the use of LSBs as flexural members in residential construction. When LSBs are used as back to back built-up sections, they are likely to improve their moment capacity. However, the research project conducted on the flexural behaviour of back to back built-up LSBs showed that the detrimental effects of lateral distortional buckling in single LSB members appear to remain with back to back built-up LSB members. The ultimate moment capacity of back to back LSB member is also affected by lateral distortional buckling failure. Therefore an investigation was conducted with an aim to develop suitable strength improvement methods, which are likely to mitigate lateral distortional buckling effects and hence improve the flexural strengths of back to back LSB members. This paper presents the details of this investigation, the results and recommendations for the most suitable and cost-effective method, which significantly improves the moment capacities of back to back LSB members.

Moving tele-monitoring and tele-treatment from promise to practice : a business model approach for a chronic lower back pain application

The availability of new information and communication technologies creates opportunities for new, mobile tele-health services. While many promising tele-health projects deliver working R&D prototypes, they often do not result in actual deployment. We aim to identify critical issues than can increase our understanding and enhance the viability of the mobile tele-health services beyond the R&D phase by developing a business model. The present study describes the systematic development and evaluation of a service-oriented business model for tele-monitoring and -treatment of chronic lower back pain patients based on a mobile technology prototype. We address challenges of multi-sector collaboration and disruptive innovation.

Control and protection of a microgrid connected to utility through back-to-back converters

This paper discusses the control and protection of a microgrid that is connected to utility through back-to-back converters. The back-to-back converter connection facilitates bidirectional power flow between the utility and the microgrid. These converters can operate in two different modes–one in which a fixed amount of power is drawn from the utility and the other in which the microgrid power shortfall is supplied by the utility. In the case of a fault in the utility or microgrid side, the protection system should act not only to clear the fault but also to block the back-to-back converters such that its dc bus voltage does not fall during fault. Furthermore, a converter internal mechanism prevents it from supplying high current during a fault and this complicates the operation of a protection system. To overcome this, an admittance based relay scheme is proposed, which has an inverse time characteristic based on measured admittance of the line. The proposed protection and control schemes are able to ensure reliable operation of the microgrid.

Beam steering with high front-to-back ratio and high directivity on small platforms using decoupled antenna pairs

Beam steering with high front-to-back ratio and high directivity on a small platform is proposed. Two closely spaced antenna pairs with eigenmode port decoupling are used as the basic radiating elements. Two orthogonal radiation patterns are obtained for each antenna pair. High front-to-back ratio and high directivity are achieved by combining the two orthogonal radiation patterns. With an infinite groundplane, a front-to-back ratio of 21 dB with a directivity of 9.8 dB can be achieved. Beam steering, at the expense of a slight decrease in directivity, is achieved by placing the two antenna pairs 0.5λ apart. The simulated half power beamwidth is 58°. A prototype was designed and the 2-D radiation patterns were measured. The prototype supports three directions of beam steering. The half power beamwidth was measured as 46°, 48°, and 50° for the three respective beam directions. The measured front-to-back ratio in azimuth plane is 8.5 dB, 8.0 dB and 7.6 dB, respectively.

Bouncing back : the role of design in facilitating students to understand and deal with adversity

After state-wide flooding and a category-5 tropical cyclone, three-quarters of the state of Queensland was declared a disaster zone in early 2011. This deluge of adversity had a significant impact on university students, a few weeks prior to the start of the academic semester. The purpose of this paper is to examine the role that design plays in facilitating students to understand and respond to, adversity. The participants of this study were second and fourth year architectural design students at a large Australian University, in Queensland. As a part of their core architectural design studies, students were required to provide architectural responses to the recent catastrophic events in Queensland. Qualitative data was obtained through student surveys, work design work submitted by students and a survey of guests who attending an exhibition of the student work. The results of this research showed that the students produced more than just the required set of architectural drawings, process journals and models, but also recognition of the important role that the affective dimension of the flooding event and the design process played in helping them to both understand and respond to, adversity. They held the ‘real world’ experience and practical aspect of the assessment in higher regard than their typical focus on aesthetics and the making of iconic design. Perhaps most importantly, the students recognised that this process allowed them to have a voice, and a means to respond to adversity through the powerful language of design.

Sky high and back again : the evolution of simulation-based design from aerospace to construction

Emerging from the challenge to reduce energy consumption in buildings is a need for research and development into the more effective use of simulation as a decision-support tool. Despite significant research, persistent limitations in process and software inhibit the integration of energy simulation in early architectural design. This paper presents a green star case study to highlight the obstacles commonly encountered with current integration strategies. It then examines simulation-based design in the aerospace industry, which has overcome similar limitations. Finally, it proposes a design system based on this contrasting approach, coupling parametric modelling and energy simulation software for rapid and iterative performance assessment of early design options.

Front page schools, back page schools : a case study of factors perceived to affect academic performance in five Papua New Guinea secondary schools

Papua New Guinea has reformed its colonial established education system and made huge investments with the help of donors to achieve equal access and quality education for all its citizens. Despite this national aspiration and these policy reforms and investments, secondary schools that enrol grade 9 students who are relatively equal in education ability show huge disparities in their grade 10 academic performances. This study examined perceptions of students, teachers and principals regarding factors affecting the disparity in academic performance in the context of a developing country. The central question for the study is: What are the perceptions of students and teachers of the factors that affect disparities in secondary schools' academic performance? This qualitative case study involved two high and three low academic performing secondary schools in Western Highlands Province of Papua New Guinea. Primary data were collected through focus groups and semi-structured interviews involving 112 participants. Students and teachers are key participants in this study, as it intends to find out the realities of schools, yet they are an under-researched group. A postcolonial and sense of community conceptual framework was developed for the analysis of the participants. perceptions. In addition, scholarship on school effectiveness and equity in education informed the interpretation of the findings. Three themes were evident in participants. views. First, participants expressed their view that differences in academic performance were related to the adequacy and equitability of resources. The inequities in resource inputs led some of them to coin the metaphor of .back page and front page. schools. Second, many expressed the view that deficiencies in implementing bilingual education, given the difficulty of catering for 800 vernacular languages, contribute to poor English proficiency and subsequent poor academic performance. Finally, participants believed that, in order to have a positive school culture, it is necessary for educators to recognise and respect contemporary students. identities, communal/tribal membership and needs. This study has implications for national education policy on resource allocation to address equality and equity, bilingual education and teacher education. Moreover, as the study found that high academic performance in this context is also influenced by intra-school social relationships, these relationships need to be nurtured. When appropriately nurtured, they become an important factor in sustaining quality education for all secondary school students. This thesis has laid the foundations for further research and invites further investigations into policy and implementation of school reforms aimed at improving academic achievement.

Physical activity amongst people with chronic back pain : an investigation of perceived barriers and facilitators to inform intervention development

Previous research has indicated people with non-specific low back pain who are physically inactive face a poorer prognosis than people with back pain who participate in low or moderate intensity physical activity. They also face a greater risk of other lifestyle related health conditions, such as diabetes and heart disease. For these reasons, contemporary non-surgical interventions for low back pain aim to incorporate a return to physical activity. However, there is a lack of empirical evidence supporting physical activity interventions for this purpose. It is likely that people with low back pain face additional challenges when trying to commence (or return to) regular physical activity. This exploratory qualitative research aimed to map out perceived barriers and facilitators to undertaking physical activity among people with non-specific low back pain to inform future intervention development.

Back to the future : prohibiting surrogacy for singles, same-sex and shorter-term heterosexual couples in Queensland

This article considers the regulatory position concerning altruistic surrogacy in Queensland, focusing on the intended changes to the current legal framework announced by the government in June 2012. The previous government had made significant progress by reforming surrogacy laws in 2010. However, that progress is at risk of being reversed. The proposed changes to the law would make it a criminal offence to enter into an altruistic surrogacy arrangement for certain individuals or couples. If enacted, the offence would only apply in altruistic surrogacy cases where the intended parent or parents are either single, in a same-sex relationship, or are in a heterosexual relationship of less than two years. Moreover, if enacted, the offence would apply extra-territorially. The authors argue that these changes represent a retrograde step for the law and urge the government to reconsider. This is based on the fact that they are out of step with current social attitudes, are contrary to the spirit of anti-discrimination laws, and that they are unjustified in terms of child welfare concerns.