Synthesis, characterization of palygorskite supported zero-valent iron and its application for methylene blue adsorption

In this work, natural palygorskite impregnated with zero-valent iron (ZVI) was prepared and characterised. The combination of ZVI particles on surface of fibrous palygorskite can help to overcome the disadvantage of ultra-fine powders which may have strong tendency to agglomerate into larger particles, resulting in an adverse effect on both effective surface area and catalyst performance. There is a significant increase of methylene blue (MB) decolourized efficiency on acid treated palygorskite with ZVI grafted, within 5 mins, the concentration of MB in the solution was decreased from 94 mg/L to around 20 mg/L and the equilibration was reached at about 30 to 60 mins with only around 10 mg/L MB remained in solution. Changes in the surface and structure of prepared materials were characterized using X-ray diffraction (XRD), infrared (IR) spectroscopy, surface analysing and scanning electron microscopy (SEM) with element analysis and mapping. Comparing with zero-valent iron and palygorskite, the presence of zero-valent iron reactive species on the palygorskite surface strongly increases the decolourization capacity for methylene blue, and it is significant for providing novel modified clay catalyst materials for the removal of organic contaminants from waste water.

Load sharing and power quality enhanced operation of a distributed microgrid

This paper describes control methods for proper load sharing between parallel converters connected in a microgrid and supplied by distributed generators (DGs). It is assumed that the microgrid spans a large area and it supplies loads in both in grid connected and islanded modes. A control strategy is proposed to improve power quality and proper load sharing in both islanded and grid connected modes. It is assumed that each of the DGs has a local load connected to it which can be unbalanced and/or nonlinear. The DGs compensate the effects of unbalance and nonlinearity of the local loads. Common loads are also connected to the microgrid, which are supplied by the utility grid under normal conditions. However during islanding, each of the DGs supplies its local load and shares the common load through droop characteristics. Both impedance and motor loads are considered to verify the system response. The efficacy of the controller has been validated through simulation for various operating conditions using PSCAD. It has been found through simulation that the total Harmonic Distortion (THD) of the of the microgrid voltage is about 10% and the negative and zero sequence component are around 20% of the positive sequence component before compensation. After compensation, the THD remain below 0.5%, whereas, negative and zero sequence components of the voltages remain below 0.02% of the positive sequence component.

Modelling urban public transit users’ route choice behaviour : a review and outlook

Public transport is one of the key promoters of sustainable urban transport. To encourage and increase public transport patronage it is important to investigate the route choice behaviours of urban public transit users. This chapter reviews the main developments of modelling urban public transit users’ route choice behaviours in a historical perspective, from the 1960s to the present time. The approaches re- viewed for this study include the early heuristic studies on finding the least-cost transit route and all-or- nothing transit assignment, the bus common lines problem, the disaggregate discrete choice models, the deterministic and stochastic user equilibrium transit assignment models, and the recent dynamic transit assignment models. This chapter also provides an outlook for the future directions of modelling transit users’ route choice behaviours. Through the comparison with the development of models for motorists’ route choice and traffic assignment problems, this chapter advocates that transit route choice research should draw inspiration from the research outcomes from the road area, and that the modelling practice of transit users’ route choice should further explore the behavioural complexities.

Design and deployment of a remote robust sensor network : experiences from an outdoor water quality monitoring network

This paper investigates a wireless sensor network deployment - monitoring water quality, e.g. salinity and the level of the underground water table - in a remote tropical area of northern Australia. Our goal is to collect real time water quality measurements together with the amount of water being pumped out in the area, and investigate the impacts of current irrigation practice on the environments, in particular underground water salination. This is a challenging task featuring wide geographic area coverage (mean transmission range between nodes is more than 800 meters), highly variable radio propagations, high end-to-end packet delivery rate requirements, and hostile deployment environments. We have designed, implemented and deployed a sensor network system, which has been collecting water quality and flow measurements, e.g., water flow rate and water flow ticks for over one month. The preliminary results show that sensor networks are a promising solution to deploying a sustainable irrigation system, e.g., maximizing the amount of water pumped out from an area with minimum impact on water quality.

The impact of brand and product placements in electronic games

In an environment where it has become increasingly difficult to attract consumer attention, marketers have begun to explore alternative forms of marketing communication. One such form that has emerged is product placement, which has more recently appeared in electronic games. Given changes in media consumption and the growth of the games industry, it is not surprising that games are being exploited as a medium for promotional content. Other market developments are also facilitating and encouraging their use, in terms of both the insertion of brand messages into video games and the creation of brand-centred environments, labelled ‘advergames’. However, while there is much speculation concerning the beneficial outcomes for marketers, there remains a lack of academic work in this area and little empirical evidence of the actual effects of this form of promotion on game players. Only a handful of studies are evident in the literature, which have explored the influence of game placements on consumers. The majority have studied their effect on brand awareness, largely demonstrating that players can recall placed brands. Further, most research conducted to date has focused on computer and online games, but consoles represent the dominant platform for play (Taub, 2004). Finally, advergames have largely been neglected, particularly those in a console format. Widening the gap in the literature is the fact that insufficient academic attention has been given to product placement as a marketing communication strategy overall, and to games in general. The unique nature of the strategy also makes it difficult to apply existing literature to this context. To address a significant need for information in both the academic and business domains, the current research investigates the effects of brand and product placements in video games and advergames on consumer attitude to the brand and corporate image. It was conducted in two stages. Stage one represents a pilot study. It explored the effects of use simulated and peripheral placements in video games on players’ and observers’ attitudinal responses, and whether these are influenced by involvement with a product category or skill level in the game. The ability of gamers to recall placed brands was also examined. A laboratory experiment was employed with a small sample of sixty adult subjects drawn from an Australian east-coast university, some of who were exposed to a console video game on a television set. The major finding of study one is that placements in a video game have no effect on gamers’ attitudes, but they are recalled. For stage two of the research, a field experiment was conducted with a large, random sample of 350 student respondents to investigate the effects on players of brand and product placements in handheld video games and advergames. The constructs of brand attitude and corporate image were again tested, along with several potential confounds. Consistent with the pilot, the results demonstrate that product placement in electronic games has no effect on players’ brand attitudes or corporate image, even when allowing for their involvement with the product category, skill level in the game, or skill level in relation to the medium. Age and gender also have no impact. However, the more interactive a player perceives the game to be, the higher their attitude to the placed brand and corporate image of the brand manufacturer. In other words, when controlling for perceived interactivity, players experienced more favourable attitudes, but the effect was so weak it probably lacks practical significance. It is suggested that this result can be explained by the existence of excitation transfer, rather than any processing of placed brands. The current research provides strong, empirical evidence that brand and product placements in games do not produce strong attitudinal responses. It appears that the nature of the game medium, game playing experience and product placement impose constraints on gamer motivation, opportunity and ability to process these messages, thereby precluding their impact on attitude to the brand and corporate image. Since this is the first study to investigate the ability of video game and advergame placements to facilitate these deeper consumer responses, further research across different contexts is warranted. Nevertheless, the findings have important theoretical and managerial implications. This investigation makes a number of valuable contributions. First, it is relevant to current marketing practice and presents findings that can help guide promotional strategy decisions. It also presents a comprehensive review of the games industry and associated activities in the marketplace, relevant for marketing practitioners. Theoretically, it contributes new knowledge concerning product placement, including how it should be defined, its classification within the existing communications framework, its dimensions and effects. This is extended to include brand-centred entertainment. The thesis also presents the most comprehensive analysis available in the literature of how placements appear in games. In the consumer behaviour discipline, the research builds on theory concerning attitude formation, through application of MacInnis and Jaworski’s (1989) Integrative Attitude Formation Model. With regards to the games literature, the thesis provides a structured framework for the comparison of games with different media types; it advances understanding of the game medium, its characteristics and the game playing experience; and provides insight into console and handheld games specifically, as well as interactive environments generally. This study is the first to test the effects of interactivity in a game environment, and presents a modified scale that can be used as part of future research. Methodologically, it addresses the limitations of prior research through execution of a field experiment and observation with a large sample, making this the largest study of product placement in games available in the literature. Finally, the current thesis offers comprehensive recommendations that will provide structure and direction for future study in this important field.

Modulation of dermal microvascular endithelial cell responses to growth factors and haemostatic factors in the presence of vitronectin

In order to effect permanent closure in burns patients suffering from full thickness wounds, replacing their skin via split thickness autografting, is essential. Dermal substitutes in conjunction with widely meshed split thickness autografts (+/- cultured keratinocytes) reduce scarring at the donor and recipient sites of burns patients by reducing demand for autologous skin (both surface area and thickness), without compromising dermal delivery at the wound face. Tissue engineered products such as Integra consist of a dermal template which is rapidly remodelled to form a neodermis, at which time the temporary silicone outer layer is removed and replaced with autologous split thickness skin. Whilst provision of a thick tissue engineered dermis at full thickness burn sites reduces scarring, it is hampered by delays in vascularisation which results in clinical failure. The ultimate success of any skin graft product is dependent upon a number of basic factors including adherence, haemostasis and in the case of viable tissue grafts, success is ultimately dependent upon restoration of a normal blood supply, and hence this study. Ultimately, the goal of this research is to improve the therapeutic properties of tissue replacements, through impregnation with growth factors aimed at stimulating migration and proliferation of microvascular endothelial cells into the donor tissue post grafting. For the purpose of my masters, the aim was to evaluate the responsiveness of a dermal microvascular endothelial cell line to growth factors and haemostatic factors, in the presence of the glycoprotein vitronectin. Vitronectin formed the backbone for my hypothesis and research due to its association with both epithelial and, more specifically, endothelial migration and proliferation. Early work using a platform technology referred to as VitroGro (Tissue Therapies Ltd), which is comprised of vitronectin bound BP5/IGF-1, aided keratinocyte proliferation. I hypothesised that this result would translate to another epithelium - endothelium. VitroGro had no effect on endothelial proliferation or migration. Vitronectin increases the presence of Fibroblast Growth Factor (FGF) and Vascular Endothelial Growth Factor (VEGF) receptors, enhancing cell responsiveness to their respective ligands. So, although Human Microvascular Endothelial Cell line 1 (HMEC-1) VEGF receptor expression is generally low, it was hypothesised that exposure to vitronectin would up-regulate this receptor. HMEC-1 migration, but not proliferation, was enhanced by vitronectin bound VEGF, as well as vitronectin bound Epidermal Growth Factor (EGF), both of which could be used to stimulate microvascular endothelial cell migration for the purpose of transplantation. In addition to vitronectin's synergy with various growth factors, it has also been shown to play a role in haemostasis. Vitronectin binds thrombin-antithrombin III (TAT) to form a trimeric complex that takes on many of the attributes of vitronectin, such as heparin affinity, which results in its adherence to endothelium via heparan sulfate proteoglycans (HSP), followed by unaltered transcytosis through the endothelium, and ultimately its removal from the circulation. This has been documented as a mechanism designed to remove thrombin from the circulation. Equally, it could be argued that it is a mechanism for delivering vitronectin to the matrix. My results show that matrix-bound vitronectin dramatically alters the effect that conformationally altered antithrombin three (cATIII) has on proliferation of microvascular endothelial cells. cATIII stimulates HMEC-1 proliferation in the presence of matrix-bound vitronectin, as opposed to inhibiting proliferation in its absence. Binding vitronectin to tissues and organs prior to transplant, in the presence of cATIII, will have a profound effect on microvascular infiltration of the graft, by preventing occlusion of existing vessels whilst stimulating migration and proliferation of endothelium within the tissue.

Basin analysis and economic geology of the Northern Mount Isa Basin

The Mount Isa Basin is a new concept used to describe the area of Palaeo- to Mesoproterozoic rocks south of the Murphy Inlier and inappropriately described presently as the Mount Isa Inlier. The new basin concept presented in this thesis allows for the characterisation of basin-wide structural deformation, correlation of mineralisation with particular lithostratigraphic and seismic stratigraphic packages, and the recognition of areas with petroleum exploration potential. The northern depositional margin of the Mount Isa Basin is the metamorphic, intrusive and volcanic complex here referred to as the Murphy Inlier (not the "Murphy Tectonic Ridge"). The eastern, southern and western boundaries of the basin are obscured by younger basins (Carpentaria, Eromanga and Georgina Basins). The Murphy Inlier rocks comprise the seismic basement to the Mount Isa Basin sequence. Evidence for the continuity of the Mount Isa Basin with the McArthur Basin to the northwest and the Willyama Block (Basin) at Broken Hill to the south is presented. These areas combined with several other areas of similar age are believed to have comprised the Carpentarian Superbasin (new term). The application of seismic exploration within Authority to Prospect (ATP) 423P at the northern margin of the basin was critical to the recognition and definition of the Mount Isa Basin. The Mount Isa Basin is structurally analogous to the Palaeozoic Arkoma Basin of Illinois and Arkansas in southern USA but, as with all basins it contains unique characteristics, a function of its individual development history. The Mount Isa Basin evolved in a manner similar to many well described, Phanerozoic plate tectonic driven basins. A full Wilson Cycle is recognised and a plate tectonic model proposed. The northern Mount Isa Basin is defined as the Proterozoic basin area northwest of the Mount Gordon Fault. Deposition in the northern Mount Isa Basin began with a rift sequence of volcaniclastic sediments followed by a passive margin drift phase comprising mostly carbonate rocks. Following the rift and drift phases, major north-south compression produced east-west thrusting in the south of the basin inverting the older sequences. This compression produced an asymmetric epi- or intra-cratonic clastic dominated peripheral foreland basin provenanced in the south and thinning markedly to a stable platform area (the Murphy Inlier) in the north. The fmal major deformation comprised east-west compression producing north-south aligned faults that are particularly prominent at Mount Isa. Potential field studies of the northern Mount Isa Basin, principally using magnetic data (and to a lesser extent gravity data, satellite images and aerial photographs) exhibit remarkable correlation with the reflection seismic data. The potential field data contributed significantly to the unravelling of the northern Mount Isa Basin architecture and deformation. Structurally, the Mount Isa Basin consists of three distinct regions. From the north to the south they are the Bowthorn Block, the Riversleigh Fold Zone and the Cloncurry Orogen (new names). The Bowthom Block, which is located between the Elizabeth Creek Thrust Zone and the Murphy Inlier, consists of an asymmetric wedge of volcanic, carbonate and clastic rocks. It ranges from over 10 000 m stratigraphic thickness in the south to less than 2000 min the north. The Bowthorn Block is relatively undeformed: however, it contains a series of reverse faults trending east-west that are interpreted from seismic data to be down-to-the-north normal faults that have been reactivated as thrusts. The Riversleigh Fold Zone is a folded and faulted region south of the Bowthorn Block, comprising much of the area formerly referred to as the Lawn Hill Platform. The Cloncurry Orogen consists of the area and sequences equivalent to the former Mount Isa Orogen. The name Cloncurry Orogen clearly distinguishes this area from the wider concept of the Mount Isa Basin. The South Nicholson Group and its probable correlatives, the Pilpah Sandstone and Quamby Conglomerate, comprise a later phase of now largely eroded deposits within the Mount Isa Basin. The name South Nicholson Basin is now outmoded as this terminology only applied to the South Nicholson Group unlike the original broader definition in Brown et al. (1968). Cored slimhole stratigraphic and mineral wells drilled by Amoco, Esso, Elf Aquitaine and Carpentaria Exploration prior to 1986, penetrated much of the stratigraphy and intersected both minor oil and gas shows plus excellent potential source rocks. The raw data were reinterpreted and augmented with seismic stratigraphy and source rock data from resampled mineral and petroleum stratigraphic exploration wells for this study. Since 1986, Comalco Aluminium Limited, as operator of a joint venture with Monument Resources Australia Limited and Bridge Oil Limited, recorded approximately 1000 km of reflection seismic data within the basin and drilled one conventional stratigraphic petroleum well, Beamesbrook-1. This work was the first reflection seismic and first conventional petroleum test of the northern Mount Isa Basin. When incorporated into the newly developed foreland basin and maturity models, a grass roots petroleum exploration play was recognised and this led to the present thesis. The Mount Isa Basin was seen to contain excellent source rocks coupled with potential reservoirs and all of the other essential aspects of a conventional petroleum exploration play. This play, although high risk, was commensurate with the enormous and totally untested petroleum potential of the basin. The basin was assessed for hydrocarbons in 1992 with three conventional exploration wells, Desert Creek-1, Argyle Creek-1 and Egilabria-1. These wells also tested and confrrmed the proposed basin model. No commercially viable oil or gas was encountered although evidence of its former existence was found. In addition to the petroleum exploration, indeed as a consequence of it, the association of the extensive base metal and other mineralisation in the Mount Isa Basin with hydrocarbons could not be overlooked. A comprehensive analysis of the available data suggests a link between the migration and possible generation or destruction of hydrocarbons and metal bearing fluids. Consequently, base metal exploration based on hydrocarbon exploration concepts is probably. the most effective technique in such basins. The metal-hydrocarbon-sedimentary basin-plate tectonic association (analogous to Phanerozoic models) is a compelling outcome of this work on the Palaeo- to Mesoproterozoic Mount lsa Basin. Petroleum within the Bowthom Block was apparently destroyed by hot brines that produced many ore deposits elsewhere in the basin.

Impact of soil texture on the distribution of soil organic matter in physical and chemical fractions

Previous research on the protection of soil organic C from decomposition suggests that soil texture affects soil C stocks. However, different pools of soil organic matter (SOM) might be differently related to soil texture. Our objective was to examine how soil texture differentially alters the distribution of organic C within physically and chemically defined pools of unprotected and protected SOM. We collected samples from two soil texture gradients where other variables influencing soil organic C content were held constant. One texture gradient (16-60% clay) was located near Stewart Valley, Saskatchewan, Canada and the other (25-50% clay) near Cygnet, OH. Soils were physically fractionated into coarse- and fine-particulate organic matter (POM), silt- and clay-sized particles within microaggregates, and easily dispersed silt-and clay-sized particles outside of microaggregates. Whole-soil organic C concentration was positively related to silt plus clay content at both sites. We found no relationship between soil texture and unprotected C (coarse- and fine-POM C). Biochemically protected C (nonhydrolyzable C) increased with increasing clay content in whole-soil samples, but the proportion of nonhydrolyzable C within silt- and clay-sized fractions was unchanged. As the amount of silt or clay increased, the amount of C stabilized within easily dispersed and microaggregate-associated silt or clay fractions decreased. Our results suggest that for a given level of C inputs, the relationship between mineral surface area and soil organic matter varies with soil texture for physically and biochemically protected C fractions. Because soil texture acts directly and indirectly on various protection mechanisms, it may not be a universal predictor of whole-soil C content.

The utilisation of skilled immigrants and skilled Refugees in countries of destination

about 82 million immigrants in the OECD area; and worldwide, there are about 191 million immigrants and displaced persons, and some 30-40 million unauthorised immigrants. Also according to recent OECD report, little in-depth research has been carried out to-date to help decision makers in government, business, and society at large, to better understand the complexities and wider consequences of future migration flows. Literatures have also indicated that the lack of a skilled population in muchneeded occupations in countries of destination have contributed to the need to bring in skilled foreign workers. Furthermore, despite current global financial crisis, some areas of occupation are in need of skilled workers such that in a job-scarce environment jobs become fewer and employers are more likely to demand skilled workers from both natives and immigrants. Global competition for labour is expected to intensify, especially for top talent, highly qualified and semi-skilled individuals. This exacerbate the problems faced by current skilled immigrants and skilled refugees, particularly those from non-main English speaking countries who are not employed at optimal skill level in countries of destination. The research study investigates whether skilled immigrants are being effectively utilised in their countries of destination, in the context of employment. In addition to skilled immigrants, data sampling will also include skilled refugees who, although arriving under the humanitarian program, possess formal qualifications from their country of origin. Underlying variables will be explored such as the strength of social capital or interpersonal ties; and human capital in terms of educational attainment and proficiency in the English Language. The aim of the study is to explain the relationship between the variables; and whether the variables influence the employment outcomes. A broad-ranging preliminary literature review has been undertaken to explore the substantial bodies of knowledge on skilled immigrants worldwide, including skilled refugees; and to investigate whether the utilisation issues are universal or specific to a country. In addition, preliminary empirical research and analysis has been undertaken, to set the research focus and to identify the problems beyond literature. Preliminary findings have indicated that immigrants and refugees from non-main English speaking countries are particularly impacted by employment issues regardless of their skills and qualifications acquired in their country of origins; compared with immigrants from main-English speaking countries. Preliminary findings from the literature review also indicate that gaps in knowledge still exist. Although the past two decades have witnessed a virtual explosion of theory and research on international migration, no in-depth research has been located that specifically links immigrants and refugees social and human capitals in terms of employment outcomes. This research study aims to fill these gaps in research; and subsequently contribute to contemporary body of knowledge in literatures on the utilisation of skilled immigrants and skilled refugees, specifically those from non-main English speaking countries. A mixed methods design will be used, which incorporates techniques from both quantitative and qualitative research traditions that will be triangulated at the end of the data collection stage.

Values, controversial issues and interfaith understanding

Values are fundamental to human activity. What makes us distinctive is our ability to understand the challenges we face in life, and to make choices about how to respond. Yet, as the Cheshire Cat from Lewis Carroll’s Alice’s Adventures in Wonderland observed, if we don’t care about how we make such choices, the outcome of our decision-making is diminished. Values education is a broad, complex and controversial area, and, while it has shifted in emphasis and focus, it continues to be an essential part of many education systems. For example, some international education systems are exploring the links between values education and student wellbeing. In Australia, the values basis for ethical behaviour is receiving emphasis as a general capability, or important component of education, that can be developed across the curriculum. Indeed, some syllabus and policy documents require that particular values are emphasised, while numerous schools aim to inculcate and foster a range of personal social, moral and spiritual values in their students, many of which are shared by members of the wider community. However, because values are also contested in the community, values education involves the exploration of controversial issues. Similarly, values education explores the underlying belief systems of different world views and how they influence value commitments, ways of behaving, and interfaith understanding in today’s globalised world. This chapter explores the significance and teaching possibilities of values, controversial issues and interfaith understanding.

Improved design method for biosecurity surveillance and early detection of non-indigenous rats

A recent advance in biosecurity surveillance design aims to benefit island conservation through early and improved detection of incursions by non-indigenous species. The novel aspects of the design are that it achieves a specified power of detection in a cost-managed system, while acknowledging heterogeneity of risk in the study area and stratifying the area to target surveillance deployment. The design also utilises a variety of surveillance system components, such as formal scientific surveys, trapping methods, and incidental sightings by non-biologist observers. These advances in design were applied to black rats (Rattus rattus) representing the group of invasive rats including R. norvegicus, and R. exulans, which are potential threats to Barrow Island, Australia, a high value conservation nature reserve where a proposed liquefied natural gas development is a potential source of incursions. Rats are important to consider as they are prevalent invaders worldwide, difficult to detect early when present in low numbers, and able to spread and establish relatively quickly after arrival. The ‘exemplar’ design for the black rat is then applied in a manner that enables the detection of a range of non-indigenous species of rat that could potentially be introduced. Many of the design decisions were based on expert opinion as data gaps exist in empirical data. The surveillance system was able to take into account factors such as collateral effects on native species, the availability of limited resources on an offshore island, financial costs, demands on expertise and other logistical constraints. We demonstrate the flexibility and robustness of the surveillance system and discuss how it could be updated as empirical data are collected to supplement expert opinion and provide a basis for adaptive management. Overall, the surveillance system promotes an efficient use of resources while providing defined power to detect early rat incursions, translating to reduced environmental, resourcing and financial costs.

Workshop on HCI and game interfaces : a long romance

This full day workshop invites participants to consider the nexus where the interests of game design, the expectations of play and HCI meet: the game interface. Game interfaces seem different to the interface to other software and there have been a number of observations. Shneiderman famously noticed that while most software designers are intent on following the tenets of the “invisible computer” and making access easy for the user, games inter-faces are made for players: they embed challenge. Schell discusses a “strange” relationship between the player and the game enabled by the interface and user interface designers frequently opine that much can be learned from the design of game interfaces. So where does the game interface actually sit? Even more interesting is the question as to whether the history of the relationship and sub-sequent expectations are now limiting the potential of game design as an expressive form. Recent innovations in I/O design such as Nintendo’s Wii, Sony’s Move and Microsoft's Kinect seem to usher in an age of physical player-enabled interaction, experience and embodied, engaged design. This workshop intends to cast light on this often mentioned and sporadically examined area and to establish a platform for new and innovative design in the field.

Characterisation of organoclays and adsorption of p-nitrophenol : environmental application

Organoclays were synthesised through ion exchange of a single surfactant for sodium ions, and characterised by a range of method including X-ray diffraction (XRD), BET, X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FT-IR), and transmission electron microscopy (TEM). The change in surface properties of montmorillonite and organoclays intercalated with the surfactant, tetradecyltrimethylammonium bromide (TDTMA) were determined using XRD through the change in basal spacing and the expansion occurred by the adsorbed p-nitrophenol. The changes of interlayer spacing were observed in TEM. In addition, the surface measurement such as specific surface area and pore volume was measured and calculated using BET method, this suggested the loaded surfactant is highly important to determine the sorption mechanism onto organoclays. The collected results of XPS provided the chemical composition of montmorillonite and organoclays, and the high-resolution XPS spectra offered the chemical states of prepared organoclays with binding energy. Using TGA and FT-IR, the confirmation of intercalated surfactant was investigated. The collected data from various techniques enable an understanding of the changes in structure and surface properties. This study is of importance to provide mechanisms for the adsorption of organic molecules, especially in contaminated environmental sites and polluted waters.

An examination of the relationship between emotional intelligence, leadership style and perceived leadership outcomes in Australian educational institutions

In the field of leadership studies transformational leadership theory (e.g., Bass, 1985; Avolio, Bass, & Jung, 1995) has received much attention from researchers in recent years (Hughes, Ginnet, & Curphy, 2009; Hunt, 1999). Many previous studies have found that transformational leadership is related to positive outcomes such as the satisfaction, motivation and performance of followers in organisations (Judge & Piccolo, 2004; Lowe, Kroeck, & Sivasubramaniam, 1996), including in educational institutions (Chin, 2007; Leithwoood & Jantzi, 2005). Hence, it is important to explore constructs that may predict leadership style in order to identify potential transformational leaders in leadership assessment and selection procedures. Several researchers have proposed that emotional intelligence (EI) is one construct that may account for hitherto unexplained variance in transformational leadership (Mayer, 2001; Watkin, 2000). Different models of EI exist (e.g., Goleman, 1995, 2001; Bar-On, 1997; Mayer & Salovey, 1997) but momentum is growing for the Mayer and Salovey (1997) model to be considered the most useful (Ashkanasy & Daus, 2005; Daus & Ashkanasy, 2005). Studies in non-educational settings claim to have found that EI is a useful predictor of leadership style and leader effectiveness (Harms & Crede, 2010; Mills, 2009) but there is a paucity of studies which have examined the Mayer and Salovey (1997) model of EI in educational settings. Furthermore, other predictor variables have rarely been controlled in previous studies and only self-ratings of leadership behaviours, rather than multiple ratings, have usually been obtained. Therefore, more research is required in educational settings to answer the question: to what extent is the Mayer and Salovey (1997) model of EI a useful predictor of leadership style and leadership outcomes? This project, set in Australian educational institutions, was designed to move research in the field forward by: using valid and reliable instruments, controlling for other predictors, obtaining an adequately sized sample of real leaders as participants and obtaining multiple ratings of leadership behaviours. Other variables commonly used to predict leadership behaviours (personality factors and general mental ability) were assessed and controlled in the project. Additionally, integrity was included as another potential predictor of leadership behaviours as it has previously been found to be related to transformational leadership (Parry & Proctor-Thomson, 2002). Multiple ratings of leadership behaviours were obtained from each leader and their supervisors, peers and followers. The following valid and reliable psychological tests were used to operationalise the variables of interest: leadership styles and perceived leadership outcomes (Multifactor Leadership Questionnaire, Avolio et al., 1995), EI (Mayer–Salovey–Caruso Emotional Intelligence Test, Mayer, Salovey, & Caruso, 2002), personality factors (The Big Five Inventory, John, Donahue, & Kentle, 1991), general mental ability (Wonderlic Personnel Test-Quicktest, Wonderlic, 2003) and integrity (Integrity Express, Vangent, 2002). A Pilot Study (N = 25 leaders and 75 raters) made a preliminary examination of the relationship between the variables included in the project. Total EI, the experiential area, and the managing emotions and perceiving emotions branches of EI, were found to be related to transformational leadership which indicated that further research was warranted. In the Main Study, 144 leaders and 432 raters were recruited as participants to assess the discriminant validity of the instruments and examine the usefulness of EI as a predictor of leadership style and perceived leadership outcomes. Scores for each leadership scale across the four rating levels (leaders, supervisors, peers and followers) were aggregated with the exception of the management-by-exception active scale of transactional leadership which had an inadequate level of interrater agreement. In the descriptive and measurement component of the Main Study, the instruments were found to demonstrate adequate discriminant validity. The impact of role and gender on leadership style and EI were also examined, and females were found to be more transformational as leaders than males. Females also engaged in more contingent reward (transactional leadership) behaviours than males, whilst males engaged in more passive/avoidant leadership behaviours than females. In the inferential component of the Main Study, multiple regression procedures were used to examine the usefulness of EI as a predictor of leadership style and perceived leadership outcomes. None of the EI branches were found to be related to transformational leadership or the perceived leadership outcomes variables included in the study. Openness, emotional stability (the inverse of neuroticism) and general mental ability (inversely) each predicted a small amount of variance in transformational leadership. Passive/avoidant leadership was inversely predicted by the understanding emotions branch of EI. Overall, EI was not found to be a useful predictor of leadership style and leadership outcomes in the Main Study of this project. Implications for researchers and human resource practitioners are discussed.

Towards automated and in-situ, near-real time 3-D reconstruction of coral reef environments

Coral reefs are biologically complex ecosystems that support a wide variety of marine organisms. These are fragile communities under enormous threat from natural and human-based influences. Properly assessing and measuring the growth and health of reefs is essential to understanding impacts of ocean acidification, coastal urbanisation and global warming. In this paper, we present an innovative 3-D reconstruction technique based on visual imagery as a non-intrusive, repeatable, in situ method for estimating physical parameters, such as surface area and volume for efficient assessment of long-term variability. The reconstruction algorithms are presented, and benchmarked using an existing data set. We validate the technique underwater, utilising a commercial-off-the-shelf camera and a piece of staghorn coral, Acropora cervicornis. The resulting reconstruction is compared with a laser scan of the coral piece for assessment and validation. The comparison shows that 77% of the pixels in the reconstruction are within 0.3 mm of the ground truth laser scan. Reconstruction results from an unknown video camera are also presented as a segue to future applications of this research.