The Victorian 260 cc Legislation. Evaluation Report Using Accident Data to December, 1982.

Learner and first year probationary motorcyclists are over-represented in traffic accidents, being involved about four times as often as full motorcycle licence holders in relation to their numbers. In an attempt to reduce this over-involvement, the Victorian Government amended the law in 1979 to restrict learner and first year probationary motorcyclists to motorcycles with engine capacities of less than 260 cc. This paper reports an evaluation which showed that casualty rates for learner and first year probationers began to decrease from mid 1979 and continued to do so until the end of 1980. A further analysis indicated that compared to full licence holder casualties, learner permit casualties were about 40% less than expected while first year probationary casualties were about 39% lower.

Numerical studies of gypsum plasterboard and MGO board lined LSF walls exposed to fire

Fire resistance of cold-formed light gauge steel frame (LSF) wall systems is enhanced by lining them with single or multiple layers of wall boards with varying thermal properties. These wall boards are gypsum plasterboards or Magnesium Oxide (MgO) boards produced by different manufacturers. Thermal properties of these boards appear to show considerable variations and this can lead to varying fire resistance levels (FRL) for their wall systems. Currently FRLs of wall systems are determined using full scale fire tests, but they are time consuming and expensive. Recent research studies on the fire performance of LSF wall systems have used finite element studies to overcome this problem, but they were developed based on 1-D and 2-D finite element platform capable of performing either heat transfer or structural analysis separately. Hence in this research a 3-D finite element model was developed first for LSF walls lined with gypsum plasterboard and cavity insulation materials. Accurate thermal properties of these boards are essential for finite element modelling, and thus they were measured at both ambient and elevated temperatures. This experimental study included specific heat, relative density and thermal conductivity of boards. The developed 3-D finite element model was then validated using the available fire tests results of LSF walls lined with gypsum plasterboard, and is being used to investigate the fire performance of different LSF wall configurations. The tested MgO board exhibited significant variations in their thermal properties in comparison to gypsum plasterboards with about 50% loss of its initial mass at about 500 ºC compared to 16% for gypsum plasterboards. Hence the FRL of MgO board lined LSF wall systems is likely to be significantly reduced. This paper presents the details of this research study on the fire performance of LSF wall systems lined with gypsum plasterboard and MgO board including the developed 3-D finite element models, thermal property tests and the results.

Drivers' ability to absorb information from co-located signs along motorways

The paper presents initial findings from an Austroads funded project NT1782 Ability to Absorb Information through Electronic and Static Signs. The paper aims to investigate how easily messages displayed on co-located signs can be absorbed, and if drivers can absorb messages and take appropriate action without any adverse impact on the safety and efficiency of driving. Co-location of three types of signs under motorway conditions was investigated: direction signs (DS), variable message signs (VMS) and variable speed limits/lane control signs (VSL/LCS). The authors reviewed global wide practices and research evidence on different types of sign co-locations. It was found that dual co-location of VSL/LCS, VMS and/or DS is a practical arrangement which has been widely practised overseas and in Australia. Triple co-location of VSL/LCS, VMS and DS is also practised overseas but is still new to the Australian driving community. The NT1782 project also employed an advanced driving simulator (ADS) to further investigate the possible impacts of sign co-location on drivers’ responses in an emergency situation and there were no obviously adverse impacts have been identified from the ADS study. The authors consolidated all findings and concluded that although there is no clear evidence showing that triple co-location gives rise to riskier behaviour, this proposition should be viewed with caution. Further evaluation of triple co-location in a real-life setting is called for.

Learning from insurance data: Injuries to other road users in motorcyclist at-fault crashes

In multi-vehicle motorcycle crashes, the motorcycle rider is less likely to be at-fault but more commonly severely injured than the other road user. Therefore, not surprisingly, crashes in which motorcycle riders are at-fault and particularly the injuries to the other road users in these crashes have received little research attention. This paper aims to address this gap in the literature by investigating the factors influencing the severity of injury to other road users in motorcyclist-at-fault crashes. Five years of data from Queensland, Australia, were obtained from a database of claims against the compulsory third party (CTP) injury insurance of the at-fault motorcyclists. Analysis of the data using an ordered probit model shows higher injury severity for crashes involving young (under 25) and older (60+) at-fault motorcyclists. Among the not at-fault road users, the young, old, and males were found to be more severely injured than others. Injuries to vehicle occupants were less severe than those to pillions. Crashes that occurred between vehicles traveling in opposite directions resulted in more severe injuries than those involving vehicles traveling in the same direction. While most existing studies have analyzed police reported crash data, this study used CTP insurance data. Comparison of results indicates the potential of using CTP insurance data as an alternative to police reported crash data for gaining a better understanding of risk factors for motorcycle crashes and injury severity.

Influences on novice drivers' speed selection - a systematic review: Application and limitations of theory and methodology

Background Excessive speed is a primary contributing factor to young novice road trauma, including intentional and unintentional speeds above posted limits or too fast for conditions. The objective of this research was to conduct a systematic review of recent investigations into novice drivers’ speed selection, with particular attention to applications and limitations of theory and methodology. Method Systematic searches of peer-reviewed and grey literature were conducted during September 2014. Abstract reviews identified 71 references potentially meeting selection criteria of investigations since the year 2000 into factors that influence (directly or indirectly) actual speed (i.e., behaviour or performance) of young (age <25 years) and/or novice (recently-licensed) drivers. Results Full paper reviews resulted in 30 final references: 15 focused on intentional speeding and 15 on broader speed selection investigations. Both sets identified a range of individual (e.g., beliefs, personality) and social (e.g., peer, adult) influences, were predominantly theory-driven and applied cross-sectional designs. Intentional speed investigations largely utilised self-reports while other investigations more often included actual driving (simulated or ‘real world’). The latter also identified cognitive workload and external environment influences, as well as targeted interventions. Discussion and implications Applications of theory have shifted the novice speed-related literature beyond a simplistic focus on intentional speeding as human error. The potential to develop a ‘grand theory’ of intentional speeding emerged and to fill gaps to understand broader speed selection influences. This includes need for future investigations of vehicle-related and physical environment-related influences and methodologies that move beyond cross-sectional designs and rely less on self-reports.

A Bayesian latent class safety performance function for identifying motor vehicle crash blackspots

The current state of the practice in Blackspot Identification (BSI) utilizes safety performance functions based on total crash counts to identify transport system sites with potentially high crash risk. This paper postulates that total crash count variation over a transport network is a result of multiple distinct crash generating processes including geometric characteristics of the road, spatial features of the surrounding environment, and driver behaviour factors. However, these multiple sources are ignored in current modelling methodologies in both trying to explain or predict crash frequencies across sites. Instead, current practice employs models that imply that a single underlying crash generating process exists. The model mis-specification may lead to correlating crashes with the incorrect sources of contributing factors (e.g. concluding a crash is predominately caused by a geometric feature when it is a behavioural issue), which may ultimately lead to inefficient use of public funds and misidentification of true blackspots. This study aims to propose a latent class model consistent with a multiple crash process theory, and to investigate the influence this model has on correctly identifying crash blackspots. We first present the theoretical and corresponding methodological approach in which a Bayesian Latent Class (BLC) model is estimated assuming that crashes arise from two distinct risk generating processes including engineering and unobserved spatial factors. The Bayesian model is used to incorporate prior information about the contribution of each underlying process to the total crash count. The methodology is applied to the state-controlled roads in Queensland, Australia and the results are compared to an Empirical Bayesian Negative Binomial (EB-NB) model. A comparison of goodness of fit measures illustrates significantly improved performance of the proposed model compared to the NB model. The detection of blackspots was also improved when compared to the EB-NB model. In addition, modelling crashes as the result of two fundamentally separate underlying processes reveals more detailed information about unobserved crash causes.

Gap acceptance behavior of mobile phone distracted drivers at roundabouts

While mobile phones have become ubiquitous in modern society, the use of mobile phones while driving is increasing at an alarming rate despite the associated crash risks. A significant safety concern is that driving while distracted by a mobile phone is more prevalent among young drivers, a less experienced driving cohort with elevated crash risk. The objective of this study was to examine the gap acceptance behavior of distracted young drivers at roundabouts. The CARRS-Q Advanced Driving Simulator was used to test participants on a simulated gap acceptance scenario at roundabouts. Conflicting traffic from the right approach of a four-legged roundabout were programmed to have a series of vehicles having the gaps between them proportionately increased from two to six seconds. Thirty-two licensed young drivers drove the simulator under three phone conditions: baseline (no phone conversation), hands-free and handheld phone conversations. Results show that distracted drivers started responding to the gap acceptance scenario at a distance closer to the roundabout and approached the roundabout at slower speeds. They also decelerated at faster rates to reduce their speeds prior to gap acceptance compared to non-distracted drivers. Although accepted gap sizes were not significantly different across phone conditions, differences in the safety margins at various gap sizes—measured by Post Encroachment Time (PET) between the driven vehicle and the conflicting vehicle—were statistically significant across phone conditions. PETs for distracted drivers were smaller across different gap sizes, suggesting a lower safety margin taken by distracted drivers compared to non-distracted drivers. The results aid in understanding how cognitive distraction resulting from mobile phone conversations while driving influences driving behavior during gap acceptance at roundabouts.

Uncertainty based online planning for UAV target finding in cluttered and GPS-denied environments

There are some scenarios in which Unmmaned Aerial Vehicle (UAV) navigation becomes a challenge due to the occlusion of GPS systems signal, the presence of obstacles and constraints in the space in which a UAV operates. An additional challenge is presented when a target whose location is unknown must be found within a confined space. In this paper we present a UAV navigation and target finding mission, modelled as a Partially Observable Markov Decision Process (POMDP) using a state-of-the-art online solver in a real scenario using a low cost commercial multi rotor UAV and a modular system architecture running under the Robotic Operative System (ROS). Using POMDP has several advantages to conventional approaches as they take into account uncertainties in sensor information. We present a framework for testing the mission with simulation tests and real flight tests in which we model the system dynamics and motion and perception uncertainties. The system uses a quad-copter aircraft with an board downwards looking camera without the need of GPS systems while avoiding obstacles within a confined area. Results indicate that the system has 100% success rate in simulation and 80% rate during flight test for finding targets located at different locations.

Thermal performance of magnesium oxide wall board using numerical modelling

Fire resistance of light-gauge steel frame (LSF) walls can be enhanced by lining them with single or multiple layers of wall boards. This research is focused on the thermal per-formance of Magnesium Oxide (MgO) wall boards in comparison to the conventional gypsum plasterboards exposed to standard fire on one side. Thermal properties of MgO board and gypsum plasterboard were measured first and then used in the finite element heat transfer models of the two types of panels. The measured thermal property results show that MgO board will perform better than the gypsum plasterboards due to its higher specific heat values at elevated temperatures. However, MgO board loses 50% of its ini-tial mass at about 500 °C compared to 16% for gypsum plasterboard. The developed finite element models were validated using the fire test results of gypsum plasterboards and then used to study the thermal performance of MgO board panels. Finite element analysis re-sults show that when MgO board panels are exposed to standard fire on one side the rate of temperature rise on the ambient side is significantly reduced compared to gypsum plas-terboard. This has the potential to improve the overall thermal performance of MgO board lined LSF walls and their fire resistance levels (FRL). However, full scale fire tests are needed to confirm this. This paper presents the details of this investigation and the results.

The ghost in the city industrial complex: Le Corbusier and the fascist theory of Urbanisme

Le Corbusier participated in an urban dialogue with the first group in France to call itself fascist: the journalist Georges Valois’s militant Faisceau des Combattants et Producteurs (1925-1927), the “Blue Shirts,” inspired by the Italian “Fasci” of Mussolini. Le Corbusier’s portrait photograph materialised on the front cover of the January 1927 issue of the Faisceau League’s newspaper Le Nouveau Siècle edited by the former anarcho-syndicalist journalist Georges Valois, its leader, who fashioned himself as the French Mussolini. Le Corbusier was described in the Revue as one of les animateurs (the “organisers”) of the Party1 – meaning a member of the technical elite who would drive the Faisceau’s plans. On 1 May 1927, the Nouveau Siècle printed a full-page feature “Le Plan Voisin” on Le Corbusier’s 1922 redesign of Paris : the architect’s single-point perspective sketch appeared below an extract lifted from the architect’s original polemic Le Centre de Paris on the pages of Le Corbusier’s second book Urbanisme published two years earlier, a treatise on urbanism.2 Three weeks later, Le Corbusier presented a slide show of his urban plans at a fascist rally for the inauguration of the Faisceau’s new headquarters on the rue du faubourg Poissonniere, thereby crystalising the architect’s hallowed status in the league...

Factors associated with self-reported driver sleepiness and incidents in city bus drivers

Driver fatigue has received increased attention during recent years and is now considered to be a major contributor to approximately 15–30% of all crashes. However, little is known about fatigue in city bus drivers. It is hypothesized that city bus drivers suffer from sleepiness, which is due to a combination of working conditions, lack of health and reduced sleep quantity and quality. The overall aim with the current study is to investigate if severe driver sleepiness, as indicated by subjective reports of having to fight sleep while driving, is a problem for city based bus drivers in Sweden and if so, to identify the determinants related to working conditions, health and sleep which contribute towards this. The results indicate that driver sleepiness is a problem for city bus drivers, with 19% having to fight to stay awake while driving the bus 2–3 times each week or more and nearly half experiencing this at least 2–4 times per month. In conclusion, severe sleepiness, as indicated by having to fight sleep during driving, was common among the city bus drivers. Severe sleepiness correlated with fatigue related safety risks, such as near crashes.

Corporate board and corporate social responsibility assurance: Evidence from China

This paper investigates the association between board characteristics and the company’s corporate social responsibility (CSR) assurance decision in China. By examining 2054 firm-years of Chinese listed companies with CSR reports from 2008 to 2012, we find that firms with a large board size, more female directors, and separation of CEO and chairman positions are more likely to engage in CSR assurance. Gender diversity also influences the CSR assurance provider choice. However, board independence and overseas background of the CEO do not affect the CSR assurance decision. Inconsistent with our prediction, firms with foreign directors are less likely to engage in voluntary CSR assurance. In summary, this research provides in-depth insights into the determinants of Chinese firms’ voluntary CSR assurance.

Australian fly-in, fly-out operations: Impacts on communities, safety workers and their families

Background Australia’s mineral, resource and infrastructure sectors continues to expand as operations in rural and remote locations increasingly rely on fly-in, fly-out or drive-in, drive-out workforces in order to become economically competitive. The issues in employing these workforces are becoming more apparent and include a range of physical, mental, psychosocial, safety and community challenges. Objectives This review aims to consolidate a range of research conducted to communicate potential challenges for industry in relation to a wide variety of issues when engaging and using FIFO/DIDO workforces which includes roster design, working hours, fatigue, safety performance, employee wellbeing, turnover, psychosocial relationships and community concerns. Methods A wide literature review was performed using EBSCOhost and Google Scholar, with a focus on FIFO or DIDO workforces engaged within the resources sector. Results A number of existing gaps in the management of FIFO workforces and potential for future research were identified. This included the identification of various roster designs and hours worked across the resources industry and how to best understand the influences of roster swings, and work hours on fatigue, safety, psychological wellbeing and job satisfaction. Fatigue management, particularly in relation to travelling after extended work shifts can increase the risk for road safety and influence safety performance while at work due to a culmination of long hours, roster cycle and accumulated sleep debt. Further challenges associated with the engagement of this workforce include feelings of isolation, physiological and general health and lifestyle concerns. Conclusions FIFO workforces appear to be at an increased risk physically and mentally due to a wide range of influences of this unique lifestyle, particularly in relation to rosters, length of shift and feelings of community disengagement. Research and data collected has been limited in understanding the influences on employee engagement, satisfaction, retention and safety. Ensuring the challenges associated with FIFO employment are understood, addressed and communicated to workers and their families may assist.

Non-resident workers: A comparison of family support services for resource, health, and defence communities

Non-resident workforces experience high labour turnover, which has an impact on organisational operations and affects worker satisfaction and, in turn, partners’ ability to cope with work-related absences. Research suggests that partner satisfaction may be increased by providing a range of support services, which include professional, practical, and social support. A search was conducted to identify support available for resources and health-industry non-resident workers. These were compared to the supports available to families of deployed defence personnel. They were used to compare and contrast the spread available for each industry. The resources industry primarily provided social support, and lacked an inclusion of professional and practical supports. Health-professional support services were largely directed towards extended locum support, rather than to Fly-In Fly-Out workers. Improving sources of support which parallel support provided to the Australian Defence Force is suggested as a way to increase partner satisfaction. The implications are to understand the level of uptake, perceived importance, and utilisation of such support services.