Impact of al passivation and cosputter on the structural property of β-FeSi2 for Al-Doped β-FeSi2/ n -Si(100) based solar cells application

The aluminum (Al) doped polycrystalline p-type β-phase iron disilicide (p-β-FeSi2) is grown by thermal diffusion of Al from Al-passivated n-type Si(100) surface into FeSi2 during crystallization of amorphous FeSi2 to form a p-type β-FeSi 2/n-Si(100) heterostructure solar cell. The structural and photovoltaic properties of p-type β-FeSi2/n-type c-Si structures is then investigated in detail by using X-ray diffraction, Raman spectroscopy, transmission electron microscopy analysis, and electrical characterization. The results are compared with Al-doped p-β-FeSi2 prepared by using cosputtering of Al and FeSi2 layers on Al-passivated n-Si(100) substrates. A significant improvement in the maximum open-circuit voltage (Voc) from 120 to 320 mV is achieved upon the introduction of Al doping through cosputtering of Al and amorphous FeSi2 layer. The improvement in Voc is attributed to better structural quality of Al-doped FeSi2 film through Al doping and to the formation of high quality crystalline interface between Al-doped β-FeSi2 and n-type c-Si. The effects of Al-out diffusion on the performance of heterostructure solar cells have been investigated and discussed in detail.

Possible impact of human CYP2E1 polymorphisms on the metabolism of acrylonitrile

Case reports of human accidental poisonings point to significant individual differences in human acrylonitrile metabolism and toxicity. A cohort of 59 persons with industrial handling of low levels of acrylonitrile has repetitively been studied from 1994 through 1999 as part of a medical surveillance programme. The analyses included adduct determinations of N-terminal N-(cyanoethyl)valine in haemoglobin and genotypings of the following cytochrome P-450 2E1 (CYP2E1) polymorphisms: G-1259C and C-1019T (two subjects heterozygous), A-316G (three subjects heterozygous), T-297A (15 subjects heterozygous), G-35T (eight subjects heterozygous), G4804A (two subjects heterozygous), T7668A (six subjects heterozygous). N-(Cyanoethyl)valine adduct levels were, if any, only slightly influenced by smoking and mainly determined by the external acrylonitrile exposures. The individual means and medians of N-(cyanoethyl)valine levels over the entire observation period were compared with the CYP2E1 variants (Wilcoxon rank sum test). No influences of the investigated CYP2E1 polymorphisms on the N-(cyanoethyl)valine levels appeared at the 5% level. However, there was a trend, at a level of P≃0.1, pointing to higher acrylonitrile-specific adduct levels in persons with the A-316G mutation. Higher adduct levels would be compatible with a slower CYP2E1-mediated metabolism of acrylonitrile and with lower extents of toxification to cyanide.

The impact of cataract surgery on vision-related quality of life for bilateral cataract patients in Ho Chi Minh City, Vietnam : a prospective study

Background To determine the impact of cataract surgery on vision-related quality of life (VRQOL) and examine the association between objective visual measures and change in VRQOL after surgery among bilateral cataract patients in Ho Chi Minh City, Vietnam. Methods A cohort of older patients with bilateral cataract was assessed one week before and one to three months after first eye or both eye cataract surgery. Visual measures including visual acuity, contrast sensitivity and stereopsis were obtained. Vision-related quality of life was assessed using the NEI VFQ-25. Descriptive analyses and a generalized linear estimating equation (GEE) analysis were undertaken to measure change in VRQOL after surgery. Results Four hundred and thirteen patients were assessed before cataract surgery and 247 completed the follow-up assessment one to three months after first or both eye cataract surgery. Overall, VRQOL significantly improved after cataract surgery (p < 0.001) particularly after both eye surgeries. Binocular contrast sensitivity (p < 0.001) and stereopsis (p < 0.001) were also associated with change in VRQOL after cataract surgery. Visual acuity was not associated with VRQOL. Conclusions Cataract surgery significantly improved VRQOL among bilateral cataract patients in Vietnam. Contrast sensitivity as well as stereopsis, rather than visual acuity significantly affected VRQOL after cataract surgery.

An analysis of the timeliness and nature of profit warnings in the aftermath of the Global Financial Crisis

The global financial crisis (GFC) has severely impacted the financial position and performance of many companies internationally. Because of its severity and associated increase in uncertainty it challenges the effectiveness of existing disclosure regulation. Australia provides a unique environment in which to test the effects of the GFC on corporate disclosure because statutory rules mandate the timely disclosure of ‘price-sensitive’ information (ASX Rule 3.1) by listed entities. Exploiting this institutional setting we investigate the determinants and timeliness of profit warnings issued by the top 500 ASX-listed firms with profit declines in the 2009 fiscal year. Our findings show that firms behave differently with regard to the issuance of profit warnings: larger and more indebted firms are more likely to issue a profit warning and tend to be timelier; surprisingly, poorer performing firms tend to release the news more quickly and this might be attributed to an increasing threat of litigation. Our analysis of profit warning determinants shows interesting results with the presence of asset impairments hindering the early disclosure of profit warnings. Our findings are novel for two main reasons: first, we provide insights into the impact of global financial crisis on profit warning behaviour; second, we are the first to examine the differential impact of alternative features of profit warnings on disclosure timeliness. The findings have implications for regulators in determining compliance with continuous disclosure rules and more broadly, for market participants in interpreting profit warnings.

Impact of simulated hyperopia on academic-related performance in children

Purpose: To investigate the impact of simulated hyperopia and sustained near work on children’s ability to perform a range of academic-related tasks. Methods: Fifteen visually normal children (mean age: 10.9 ± 0.8 years; 10 males and 5 females) were recruited. Performance on a range of standardised academic-related outcome measures was assessed with and without 2.50 D of simulated bilateral hyperopia (administered in a randomised order), before and after 20 minutes of sustained near work, at two separate testing sessions. Academic-related measures included a standardised reading test (the Neale Analysis of Reading Ability), visual information processing tests (Coding and Symbol Search subtests from the Wechsler Intelligence Scale for Children) and a reading-related eye movement test (the Developmental Eye Movement test). Results: Simulated bilateral hyperopia and sustained near work each independently impaired reading, visual information processing and reading-related eye movement performance (p<0.001). A significant interaction was also demonstrated between these factors (p<0.001), with the greatest decrement in performance observed when simulated hyperopia was combined with sustained near work. This combination resulted in performance reductions of between 5% and 24% across the range of academic-related measures. A significant moderate correlation was also found between the change in horizontal near heterophoria and the change in several of the academic-related outcome measures, following the addition of simulated hyperopia. Conclusions: A relatively low level of simulated bilateral hyperopia impaired children’s performance on a range of academic–related outcome measures, with sustained near work further exacerbating this effect. Further investigations are required to determine the impact of correcting low levels of hyperopia on academic performance in children.

Numerical studies on CFRP strengthened steel columns under transverse impact

Strengthening of metallic structures using carbon fibre reinforced polymer (CFRP) has become a smart strengthening option over the conventional strengthening method. Transverse impact loading due to accidental vehicular collision can lead to the failure of existing steel hollow tubular columns. However, knowledge is very limited on the behaviour of CFRP strengthened steel members under dynamic impact loading condition. This paper deals with the numerical simulation of CFRP strengthened square hollow section (SHS) steel columns under transverse impact loading to predict the behaviour and failure modes. The transverse impact loading is simulated using finite element (FE) analysis based on numerical approach. The accuracy of the FE modelling is ensured by comparing the predicted results with available experimental tests. The effects of impact velocity, impact mass, support condition, axial loading and CFRP thickness are examined through detail parametric study. The impact simulation results indicate that the strengthening technique shows an improved impact resistance capacity by reducing lateral displacement of the strengthened column about 58% compared to the bare steel column. Axial loading plays an important role on the failure behaviour of tubular column.

What is plan B? Using Foucault's archaeology to enhance policy analysis

Many governments in western democracies conduct the work of leading their societies forward through policy generation and implementation. Despite government attempts at extensive negotiation, collaboration and debate, the general populace in these same countries frequently express feelings of disempowerment and undue pressure to be compliant, often leading to disengagement. Here we outline Plan B: a process for examining how policies that emerge from good intentions are frequently interpreted as burdensome or irrelevant by those on whom they have an impact. Using a case study of professional standards for teachers in Australia, we describe how we distilled Foucault’s notions of archaeology into a research approach centring on the creation of ‘polyhedrons of intelligibility’ as an alternative approach by which both policy makers and those affected by their policies may understand how their respective causes are supported and adversely affected.

Causal factors of hot air ballooning incidents : identification, frequency, and potential impact

Background: Hot air ballooning incidents are relatively rare, however, when they do occur they are likely to result in a fatality or serious injury. Human error is commonly attributed as the cause of hot air ballooning incidents; however, error in itself is not an explanation for safety failures. This research aims to identify, and establish the relative importance of factors contributing towards hot air ballooning incidents. Methods: Twenty-two Australian Ballooning Federation (ABF) incident reports were thematically coded using a bottom up approach to identify causal factors. Subsequently, 69 balloonists (mean 19.51 years’ experience) participated in a survey to identify additional causal factors and rate (out of seven) the perceived frequency and potential impact to ballooning operations of each of the previously identified causal factors. Perceived associated risk was calculated by multiplying mean perceived frequency and impact ratings. Results: Incident report coding identified 54 causal factors within nine higher level areas: Attributes, Crew resource management, Equipment, Errors, Instructors, Organisational, Physical Environment, Regulatory body and Violations. Overall, ‘weather’, ‘inexperience’ and ‘poor/inappropriate decisions’ were rated as having greatest perceived associated risk. Discussion: Although errors were nominated as a prominent cause of hot air ballooning incidents, physical environment and personal attributes are also particularly important for safe hot air ballooning operations. In identifying a range of causal factors the areas of weakness surrounding ballooning operations have been defined; it is hoped that targeted safety and training strategies can now be put into place removing these contributing factors and reducing the chance of pilot error.

Impact of high PV penetration on distribution transformer life time

Integration of rooftop photovoltaics (PVs) in residential networks at moderate penetration levels is becoming a reality in many countries including Australia. Despite the technical challenges in properly accommodating PV units, one of the major benefits is the ability of PV units to extend useful life time of distribution transformers. This effect is not quantified in the existing literature. This paper carries out an analysis into the impacts of rooftop PVs at different penetration levels on the performance of distribution transformers and residential networks. This paper presents a methodology to quantify the benefit of the distribution transformer life extension brought about by customer-owned rooftop PV units. The proposed methodology is applied to a real distribution system with various scenarios, including different penetration levels. The results show the distribution transformer loss-of-life function, as a function of the rooftop PV penetration level, is monotonically decreasing function which saturates after a certain penetration level. The best life improvements occur with transformers that are highly loaded and the presence of a significant PV installation may support the deferral of transformer upgrades.

The perspectives of older drivers on the impact of feedback on their driving behaviours : a qualitative study

Self-regulation is a coping strategy that allows older drivers to drive safely for longer. Self-regulation depends largely on the ability of drivers to evaluate their own driving. Therefore the success of self-regulation, in terms of driving safety, is influenced by the ability of older drivers to have insight into their declining driving performance. In addition, previous studies suggest that providing feedback to older adults regarding their driving skills may lead them to change their driving behaviour. However, little is currently known about the impact of feedback on older drivers’ self-awareness and their subsequent driving regulatory behaviour. This study explored the process of self-regulation and driving cessation among older drivers using the PAPM as a framework. It also investigated older adults’ perceptions and opinions about receiving feedback in regards to their driving abilities. Qualitative focus groups with 27 participants aged 70 years or more were conducted. Thematic analysis resulted in the development of five main themes; the meaning of driving, changes in driving pattern, feedback, the planning process, and solutions. The analysis also resulted in an initial model of driving self-regulation among older drivers that is informed by the current research and the Precaution Adoption Process Model as the theoretical framework. It identifies a number of social, personal, and environmental factors that can either facilitate or hinder people’s transition between stages of change. The findings from this study suggest that further elaboration of the PAPM is needed to take into account the role of insight and feedback on the process of self-regulation among older drivers.

Stability analysis of STATCOM in distribution networks

This chapter presents the stability analysis based on bifurcation theory of the distribution static compensator (DSTATCOM) operating both in current control mode as in voltage control mode. The bifurcation analysis allows delimiting the operating zones of nonlinear power systems and hence the computation of these boundaries is of interest for practical design and planning purposes. Suitable mathematical representations of the DSTATCOM are proposed to carry out the bifurcation analyses efficiently. The stability regions in the Thevenin equivalent plane are computed for different power factors at the Point of Common Coupling (PCC). In addition, the stability regions in the control gain space are computed, and the DC capacitor and AC capacitor impact on the stability are analyzed in detail. It is shown through bifurcation analysis that the loss of stability in the DSTATCOM is in general due to the emergence of oscillatory dynamics. The observations are verified through detailed simulation studies.

Dynamic simulation of CFRP strengthened steel column under impact loading

Carbon fibre reinforced polymer (CFRP) strengthening of metallic structures under static loading has shown great potential in the recent years. However, steel structures are often experienced natural (e.g. earthquake, wind) as well as man-made (e.g. vehicular impact, blast) dynamic loading. Therefore, there is a growing interest among the researchers to investigate the capability of CFRP strengthened members under such dynamic conditions. This study focuses on the finite element (FE) numerical modelling and simulation of CFRP strengthened steel column under transverse impact loading to predict the behaviour and failure modes. Impact simulation process and the CFRP strengthened steel column are validated with the existing experimental results in literature. The validated FE model of CFRP strengthened steel column is then further used to investigate the effects of transverse impact loading on its structural performance. The results are presented in terms of transvers e impact force, lateral and axial displacement, and deformed shape to evaluate the effectiveness of CFRP strengthening technique. Comparisons between the bare steel and CFRP strengthened steel columns clearly indicate the performance enhancement of strengthened column under transverse impact loading.

A theory of process modeling impact

Process modeling – the design and use of graphical documentations of an organization’s business processes – is a key method to document and use information about the operations of businesses. Still, despite current interest in process modeling, this research area faces essential challenges. Key unanswered questions concern the impact of process modeling in organizational practice, and the mechanisms through which impacts are developed. To answer these questions and to provide a better understanding of process modeling impact, I turn to the concept of affordances. Affordances describe the possibilities for goal-oriented action that a technical object offers to a user. This notion has received growing attention from IS researchers. The purpose of my research is to further develop the IS discipline’s understanding of affordances and impacts from information objects, such as process models used by analysts for information systems analysis and design. Specifically, I seek to extend existing theory on the emergence, perception and actualization of affordances. I develop a research model that describes the process by which affordances emerge between an individual and an object, how affordances are perceived, and how they are actualized by the individual. The proposed model also explains the role of available information for the individual, and the influence of perceived actualization effort. I operationalize and test this research model empirically, using a full-cycle, mixed methods study consisting of case study and experiment.

“Back to the future” – a retrospective analysis of university business models

Using established strategic management and business model frameworks we map the evolution of universities in the context of their value proposition to students as consumers of their products. We argue that in the main universities over time have transitioned from a value-based business model through to an efficiency-based business model that for numerous reasons, is becoming rapidly unsustainable. We further argue that the future university business models would benefit with a reconfiguration towards a network value based model. This approach requires a revised set of perceived benefits, better aligned to the current and future expectations and an alternate approach to the delivery of those benefits to learner / consumers.

Confirmatory factor analysis and invariance testing of the Young Carer of Parents Inventory (YCOPI)

Objective Research into youth caregiving in families where a parent experiences a significant medical condition has been hampered by a lack of contextually sensitive measures of the nature and breadth of young caregiving experiences. This study examined the factor structure and measurement invariance of such a measure called the Young Carer of Parents Inventory (YCOPI; Pakenham et al., 2006) using confirmatory factor analysis across 3 groups of youth. The YCOPI has 2 parts: YCOPI-A with 5 factors assessing caregiving experiences that are applicable to all caregiving contexts; YCOPI-B with 4 factors that tap dimensions related to youth caregiving in the context of parent illness. Design Two samples (ages 9–20 years) were recruited: a community sample of 2,429 youth from which 2 groups were derived (“healthy” family [HF], n = 1760; parental illness [PI], n = 446), and a sample of 130 youth of a parent with multiple sclerosis). Results With some modification, the YCOPI-A demonstrated a replicable factor structure across 3 groups, and exhibited only partial measurement invariance across the HF and PI groups. The impact of assuming full measurement invariance on latent mean differences appeared small, supporting use of the measure in research and applied settings when estimated using latent factors and controlling for measurement invariance. PI youth reported significantly higher scores than did HF youth on all YCOPI-A subscales. The YCOPI-B requires some modifications, and further development work is recommended. Conclusion The factor structure that emerged and the addition of new items constitutes the YCOPI-Revised. Findings support the use of the YCOPI-Revised in research and applied settings.