Numerical modeling of thin steel roof battens under wind uplift loads

Extreme wind events such as tropical cyclones, tornadoes and storms are more likely to impact the Australian coastal regions due to possible climate changes. Such events can be extremely destructive to building structures, in particular, low-rise buildings with lightweight roofing systems that are commonly made of thin steel roofing sheets and battens. Large wind uplift loads that act on the roofs during high wind events often cause premature roof connection failures. Recent wind damage investigations have shown that roof failures have mostly occurred at the batten to rafter or truss screw connections. In most of these cases, the screw fastener heads pulled through the bottom flanges of thin steel roof battens. This roof connection failure is very critical as both roofing sheets and battens will be lost during the high wind events. Hence, a research study was conducted to investigate this critical pull-through failure using both experimental and numerical methods. This paper presents the details of numerical modeling and the results.

Different approaches of applying single-objective binary genetic algorithm on the wind farm design

This paper discusses three different ways of applying the single-objective binary genetic algorithm into designing the wind farm. The introduction of different applications is through altering the binary encoding methods in GA codes. The first encoding method is the traditional one with fixed wind turbine positions. The second involves varying the initial positions from results of the first method, and it is achieved by using binary digits to represent the coordination of wind turbine on X or Y axis. The third is the mixing of the first encoding method with another one, which is by adding four more binary digits to represent one of the unavailable plots. The goal of this paper is to demonstrate how the single-objective binary algorithm can be applied and how the wind turbines are distributed under various conditions with best fitness. The main emphasis of discussion is focused on the scenario of wind direction varying from 0° to 45°. Results show that choosing the appropriate position of wind turbines is more significant than choosing the wind turbine numbers, considering that the former has a bigger influence on the whole farm fitness than the latter. And the farm has best performance of fitness values, farm efficiency, and total power with the direction between 20°to 30°.

Integration of Opinion Mining into customer analysis model

This research proposes a multi-dimensional model for Opinion Mining, which integrates customers' characteristics and their opinions about products (or services). Customer opinions are valuable for companies to deliver right products or services to their customers. This research presents a comprehensive framework to evaluate opinions' orientation based on products' hierarchy attributes. It also provides an alternative way to obtain opinion summaries for different groups of customers and different categories of produces.

A Web-based system enabling the integration, analysis, and 3D sub-surface visualization of groundwater monitoring data and geological models

The 3D Water Chemistry Atlas is an intuitive, open source, Web-based system that enables the three-dimensional (3D) sub-surface visualization of ground water monitoring data, overlaid on the local geological model (formation and aquifer strata). This paper firstly describes the results of evaluating existing virtual globe technologies, which led to the decision to use the Cesium open source WebGL Virtual Globe and Map Engine as the underlying platform. Next it describes the backend database and search, filtering, browse and analysis tools that were developed to enable users to interactively explore the groundwater monitoring data and interpret it spatially and temporally relative to the local geological formations and aquifers via the Cesium interface. The result is an integrated 3D visualization system that enables environmental managers and regulators to assess groundwater conditions, identify inconsistencies in the data, manage impacts and risks and make more informed decisions about coal seam gas extraction, waste water extraction, and water reuse.

Integration over song classification replicates: song variant analysis in the hihi

Human expert analyses are commonly used in bioacoustic studies and can potentially limit the reproducibility of these results. In this paper, a machine learning method is presented to statistically classify avian vocalizations. Automated approaches were applied to isolate bird songs from long field recordings, assess song similarities, and classify songs into distinct variants. Because no positive controls were available to assess the true classification of variants, multiple replicates of automatic classification of song variants were analyzed to investigate clustering uncertainty. The automatic classifications were more similar to the expert classifications than expected by chance. Application of these methods demonstrated the presence of discrete song variants in an island population of the New Zealand hihi (Notiomystis cincta). The geographic patterns of song variation were then revealed by integrating over classification replicates. Because this automated approach considers variation in song variant classification, it reduces potential human bias and facilitates the reproducibility of the results.

Optimum position of steel outrigger system for high rise composite buildings subjected to wind loads

The responses of composite buildings under wind loads clearly become more critical as the building becomes taller, less stiff and more lightweight. When the composite building increases in height, the stiffness of the structure becomes more important factor and introduction to belt truss and outrigger system is often used to provide sufficient lateral stiffness to the structure. Most of the research works to date is limited to reinforced concrete building with outrigger system of concrete structure, simple building plan layout, single height of a building, one direction wind and single level of outrigger arrangement. There is a scarcity in research works about the effective position of outrigger level on composite buildings under lateral wind loadings when the building plan layout, height and outrigger arrangement are varied. The aim of this paper is to determine the optimum location of steel belt and outrigger systems by using different arrangement of single and double level outrigger for different size, shape and height of composite building. In this study a comprehensive finite element modelling of composite building prototypes is carried out, with three different layouts (Rectangular, Octagonal and L shaped) and for three different storey (28, 42 and 57-storey). Models are analysed for dynamic cyclonic wind loads with various combination of steel belt and outrigger bracings. It is concluded that the effectiveness of the single and double level steel belt and outrigger bracing are varied based on their positions for different size, shape and height of composite building.

Global business services: Increasing specialization and integration of the world economy as drivers of economic growth

Purpose The purpose of this paper is to explore the contribution of global business services to improved productivity and economic growth of the world economy, which has gone largely unnoticed in service research. Design/methodology/approach The authors draw on macroeconomic data and industry reports, and link them to the non-ownership-concept in service research and theories of the firm. Findings Business services explain a large share of the growth of the global service economy. The fast growth of business services coincides with shifts from domestic production towards global outsourcing of services. A new wave of global business services are traded across borders and have emerged as important drivers of growth in the world’s service sector. Research limitations/implications This paper advances the understanding of non-ownership services in an increasingly global and specialized post-industrial economy. The paper makes a conceptual contribution supported by descriptive data, but without empirical testing. Originality/value The authors integrate the non-ownership concept and three related economic theories of the firm to explain the role of global business services in driving business performance and the international transformation of service economies.

The role of knowledge integration in innovation and capability development

Purpose This paper investigates the interrelationships between knowledge integration (KI), product innovation and capability development to enhance our understanding of how firms can develop capability at the firm level, which in turn enhances their performance. One of the critical underlying mechanisms for capability building identified in the literature is the role of knowledge integration, which operates within product innovation projects and contributes to dynamic capability development. Therefore, the main research question is “how does the integration of knowledge across product innovation projects lead to the development of capability?” Design/methodology/approach We adopted a case-based approach and investigated the case of a successful firm that was able to sustain its performance through a series of product innovation projects. In particular this research focused on the role of KI and firm-level capability development over the course of four projects, during which the firm successfully managed the transformation of its product base and renewal of its competitive advantage. For this purpose an in-depth case study of capability development was undertaken at the Iran Khodro Company (IKCO), the key player in the Iranian auto industry transformation. Originality/value This research revealed that along with changes at each level of product architecture “design knowledge” and “design capability” have been developed at the same level of product architecture, leading to capability development at that level. It can be argued that along the step by step maturation of radical innovation across the four case projects, architectural knowledge and capability have been developed at the case company, resulting in the gradual emergence of a modular product and capability architecture across different levels of product architecture. Such findings basically add to extensive emphasis in the literature on the interrelationship of the concept of modularity with knowledge management and capability development. Practical implications Findings of this study indicate that firms manage their knowledge in accordance with the level of specialization in knowledge and capability. Furthermore, firms design appropriate knowledge integration mechanisms within and among functions in order dynamically align knowledge processes at different levels of the product architecture. Accordingly, the outcomes of this study may guide practitioners in managing their knowledge processes, through dynamically employing knowledge integration modes step-by-step and from the part level to the architectural level of product architecture across a sequence of product innovation projects to encourage learning and radical innovation.

Gone with the wind: copyright law and fair use

The copyright defence of fair use has been tested in a recent United States case involving the classic Gone with the wind. [Suntrust Bank, as Trustee of the Stephens Mitchell trusts v Houghton Mifflin Company (2001) 136 F. Supp. 2d 1357; and Suntrust Bank, as Trustee of the Stephens Mitchell trusts v Houghton Mifflin Company (2001) US Appeal Lexis 21690.]

Speed-based diagnostics of aerodynamic and mass imbalance in large wind turbines

Any kind of imbalance in the operation of a wind turbine has adverse effect on the downstream torsional components as well as tower structure. It is crucial to detect imbalance at its very inception. The identification of the type of imbalance is also required so that appropriate measures of fault accommodation can be performed in the control system. In particular, it is important to distinguish between mass and aerodynamic imbalance. While the former is gradually caused by a structural anomaly (e.g. ice deposition, moisture accumulation inside blade), the latter is generally associated to a fault in the pitch control system. This paper proposes a technique for the detection and identification of imbalance fault in large scale wind turbines. Unlike most other existing method it requires only the rotor speed signal which is readily available in existing turbines. Signature frequencies have been proposed in this work to identify imbalance type based on their physical phenomenology. The performance of this technique has been evaluated by simulations using an existing benchmark model. The effectiveness of the proposed method has been confirmed by the simulation results.

Integration of Geospatial and Built Environment - National Data Policy

Digital technology offers enormous benefits (economic, quality of design and efficiency in use) if adopted to implement integrated ways of representing the physical world in a digital form. When applied across the full extent of the built and natural world, it is referred to as the Digital Built Environment (DBE) and encompasses a wide range of approaches and technology initiatives, all aimed at the same end goal: the development of a virtual world that sufficiently mirrors the real world to form the basis for the smart cities of the present and future, enable efficient infrastructure design and programmed maintenance, and create a new foundation for economic growth and social well-being through evidence-based analysis. The creation of a National Data Policy for the DBE will facilitate the creation of additional high technology industries in Australia; provide Governments, industries and citizens with greater knowledge of the environments they occupy and plan; and offer citizen-driven innovations for the future. Australia has slipped behind other nations in the adoption and execution of Building Information Modelling (BIM) and the principal concern is that the gap is widening. Data driven innovation added $67 billion to the Australian economy in 20131. Strong open data policy equates to $16 billion in new value2. Australian Government initiatives such as the Digital Earth inspired “National Map” offer a platform and pathway to embrace the concept of a “BIM Globe”, while also leveraging unprecedented growth in open source / open data collaboration. Australia must address the challenges by learning from international experiences—most notably the UK and NZ—and mandate the use of BIM across Government, extending the Framework for Spatial Data Foundation to include the Built Environment as a theme and engaging collaboration through a “BIM globe” metaphor. This proposed DBE strategy will modernise the Australian urban planning and the construction industry. It will change the way we develop our cities by fundamentally altering the dynamics and behaviours of the supply chains and unlocking new and more efficient ways of collaborating at all stages of the project life-cycle. There are currently two major modelling approaches that contribute to the challenge of delivering the DBE. Though these collectively encompass many (often competing) approaches or proprietary software systems, all can be categorised as either: a spatial modelling approach, where the focus is generally on representing the elements that make up the world within their geographic context; and a construction modelling approach, where the focus is on models that support the life cycle management of the built environment. These two approaches have tended to evolve independently, addressing two broad industry sectors: the one concerned with understanding and managing global and regional aspects of the world that we inhabit, including disciplines concerned with climate, earth sciences, land ownership, urban and regional planning and infrastructure management; the other is concerned with planning, design, construction and operation of built facilities and includes architectural and engineering design, product manufacturing, construction, facility management and related disciplines (a process/technology commonly known as Building Information Modelling, BIM). The spatial industries have a strong voice in the development of public policy in Australia, while the construction sector, which in 2014 accounted for around 8.5% of Australia’s GDP3, has no single voice and because of its diversity, is struggling to adapt to and take advantage of the opportunity presented by these digital technologies. The experience in the UK over the past few years has demonstrated that government leadership is very effective in stimulating industry adoption of digital technologies by, on the one hand, mandating the use of BIM on public procurement projects while at the same time, providing comparatively modest funding to address the common issues that confront the industry in adopting that way of working across the supply chain. The reported result has been savings of £840m in construction costs in 2013/14 according to UK Cabinet Office figures4. There is worldwide recognition of the value of bringing these two modelling technologies together. Australia has the expertise to exercise leadership in this work, but it requires a commitment by government to recognise the importance of BIM as a companion methodology to the spatial technologies so that these two disciplinary domains can cooperate in the development of data policies and information exchange standards to smooth out common workflows. buildingSMART Australasia, SIBA and their academic partners have initiated this dialogue in Australia and wish to work collaboratively, with government support and leadership, to explore the opportunities open to us as we develop an Australasian Digital Built Environment. As part of that programme, we must develop and implement a strategy to accelerate the adoption of BIM processes across the Australian construction sector while at the same time, developing an integrated approach in concert with the spatial sector that will position Australia at the forefront of international best practice in this area. Australia and New Zealand cannot afford to be on the back foot as we face the challenges of rapid urbanisation and change in the global environment. Although we can identify some exemplary initiatives in this area, particularly in New Zealand in response to the need for more resilient urban development in the face of earthquake threats, there is still much that needs to be done. We are well situated in the Asian region to take a lead in this challenge, but we are at imminent risk of losing the initiative if we do not take action now. Strategic collaboration between Governments, Industry and Academia will create new jobs and wealth, with the potential, for example, to save around 20% on the delivery costs of new built assets, based on recent UK estimates.

A manager-centred perspective on work-life integration

Decades of research has shown that the uptake of workplace ‘flexibility’ provisions set out in organizational/HR policies rests heavily on the support of line managers. However, the majority of scholarship addressing the intersection of managers’ roles and work-life integration has been employee-centred. That is, the literature primarily situates managers as gatekeepers to the effective implementation of work and family policies as they affect employees or workers, examining their role in, for example, approving requests to adjust or personalise employees’ work schedules; influencing whether employees are cross-trained to undertake the work of others during absences; publicising available policies; and creating norms supporting the use of formal provisions (Ryan & Ernst Kossek, 2008). Managers’ actions are primarily seen as key, contingent phenomena affecting the adoption and diffusion of work-life initiatives in an organization; consequently impacting on the work-life outcomes of subordinate employees (Bardoel, 2003; Gregory & Milner, 2012).

Real-time wind speed estimation and compensation for improved flight

This paper presents the development and experimental validation of a prototype system for online estimation and compensation of wind disturbances onboard small Rotorcraft unmanned aerial systems (RUAS). The proposed approach consists of integrating a small pitot-static system onboard the vehicle and using simple but effective algorithms for estimating the wind speed in real time. The baseline flight controller has been augmented with a feed-forward term to compensate for these wind disturbances, thereby improving the flight performance of small RUAS in windy conditions. The paper also investigates the use of online airspeed measurements in a closed-loop for controlling the RUAS forward motion without the aid of a global positioning system (GPS). The results of more than 80 flights with a RUAS confirm the validity of our approach.

Pathophysiology team teaching: Bioscientist contribution to knowledge integration in a nursing subject

Bioscience content within undergraduate nursing degrees provides foundational knowledge of pathophysiology, anatomy, physiology, microbiology and pharmacology. However, nursing students often find studying the bioscience components of undergraduate nursing program daunting (Friedel & Treagust 2005, Craft et al. 2013). This is related to factors such as the volume of content, degree of difficulty and insufficient linkage between bioscience concepts and nurses' clinical practice. Students who are unable to conceptualise the relevance of bioscience with nursing subjects and subsequent nursing practice may not appreciate the broader importance of bioscience, and hence may adopt a surface approach to learning (Craft et al. 2013). The aim of this study was to develop a model within Nursing Practice in the Context theory subject, to include a bioscientist lecturing to complement the nursing lecturer, in order to explicitly demonstrate links between physiology, pathophysiology and nursing practice.

Advancing practice in critical care: A model of knowledge integration

It could be argued that advancing practice in critical care has been superseded by the advanced practice agenda. Some would suggest that advancing practice is focused on the core attributes of an individuals practice progressing onto advanced practice status. However, advancing practice is more of a process than identifiable skills and as such is often negated when viewing the development of practitioners to the advanced practice level. For example practice development initiatives can be seen as advancing practice for the masses which ensures that practitioners are following the same level of practice. The question here is; are they developing individually.