Generalized element load method for first- and second-order element solutions with element load effect

The finite element method in principle adaptively divides the continuous domain with complex geometry into discrete simple subdomain by using an approximate element function, and the continuous element loads are also converted into the nodal load by means of the traditional lumping and consistent load methods, which can standardise a plethora of element loads into a typical numerical procedure, but element load effect is restricted to the nodal solution. It in turn means the accurate continuous element solutions with the element load effects are merely restricted to element nodes discretely, and further limited to either displacement or force field depending on which type of approximate function is derived. On the other hand, the analytical stability functions can give the accurate continuous element solutions due to element loads. Unfortunately, the expressions of stability functions are very diverse and distinct when subjected to different element loads that deter the numerical routine for practical applications. To this end, this paper presents a displacement-based finite element function (generalised element load method) with a plethora of element load effects in the similar fashion that never be achieved by the stability function, as well as it can generate the continuous first- and second-order elastic displacement and force solutions along an element without loss of accuracy considerably as the analytical approach that never be achieved by neither the lumping nor consistent load methods. Hence, the salient and unique features of this paper (generalised element load method) embody its robustness, versatility and accuracy in continuous element solutions when subjected to the great diversity of transverse element loads.

Novel non-linear elastic structural analysis with generalised transverse element loads using a refined finite element

In the finite element modelling of structural frames, external loads such as wind loads, dead loads and imposed loads usually act along the elements rather than at the nodes only. Conventionally, when an element is subjected to these general transverse element loads, they are usually converted to nodal forces acting at the ends of the elements by either lumping or consistent load approaches. In addition, it is especially important for an element subjected to the first- and second-order elastic behaviour, to which the steel structure is critically prone to; in particular the thin-walled steel structures, when the stocky element section may be generally critical to the inelastic behaviour. In this sense, the accurate first- and second-order elastic displacement solutions of element load effect along an element is vitally crucial, but cannot be simulated using neither numerical nodal nor consistent load methods alone, as long as no equilibrium condition is enforced in the finite element formulation, which can inevitably impair the structural safety of the steel structure particularly. It can be therefore regarded as a unique element load method to account for the element load nonlinearly. If accurate displacement solution is targeted for simulating the first- and second-order elastic behaviour on an element on the basis of sophisticated non-linear element stiffness formulation, the numerous prescribed stiffness matrices must indispensably be used for the plethora of specific transverse element loading patterns encountered. In order to circumvent this shortcoming, the present paper proposes a numerical technique to include the transverse element loading in the non-linear stiffness formulation without numerous prescribed stiffness matrices, and which is able to predict structural responses involving the effect of first-order element loads as well as the second-order coupling effect between the transverse load and axial force in the element. This paper shows that the principle of superposition can be applied to derive the generalized stiffness formulation for element load effect, so that the form of the stiffness matrix remains unchanged with respect to the specific loading patterns, but with only the magnitude of the loading (element load coefficients) being needed to be adjusted in the stiffness formulation, and subsequently the non-linear effect on element loadings can be commensurate by updating the magnitude of element load coefficients through the non-linear solution procedures. In principle, the element loading distribution is converted into a single loading magnitude at mid-span in order to provide the initial perturbation for triggering the member bowing effect due to its transverse element loads. This approach in turn sacrifices the effect of element loading distribution except at mid-span. Therefore, it can be foreseen that the load-deflection behaviour may not be as accurate as those at mid-span, but its discrepancy is still trivial as proved. This novelty allows for a very useful generalised stiffness formulation for a single higher-order element with arbitrary transverse loading patterns to be formulated. Moreover, another significance of this paper is placed on shifting the nodal response (system analysis) to both nodal and element response (sophisticated element formulation). For the conventional finite element method, such as the cubic element, all accurate solutions can be only found at node. It means no accurate and reliable structural safety can be ensured within an element, and as a result, it hinders the engineering applications. The results of the paper are verified using analytical stability function studies, as well as with numerical results reported by independent researchers on several simple frames.

Implementation of individualised medication administration guides for patients with dysphagia: Results from a pilot controlled trial

Introduction Patients with dysphagia (PWDs) have been shown to be four times more likely to suffer medication administration errors (MAEs).1 2 Individualised medication administration guides (I-MAGs) which outline how each formulation should be administered, have been developed to standardise medication administration by nurses on the ward and reduce the likelihood of errors. This pilot study aimed to determine the recruitment rates, estimate effect on errors and develop the intervention to design a future full scale randomised controlled trial to determine the costs and effects of I-MAG implementation. Ethical approval was granted by local ethics committee. Method Software was developed to enable I-MAG production (based on current best practice)3 4 for all PWDs on two care of the older person wards admitted during a six month period from January to July 2011. I-MAGs were attached to the medication administration record charts to be utilised by nurses when administering medicines. Staff training was provided for all staff on the intervention wards. Two care of the older person wards in the same hospital were used for control purposes. All patients with dysphagia were recruited for follow up purposes at discharge. Four ward rounds at each intervention and control ward were observed pre and post I-MAG implementation to determine the level of medication administration errors. NHS ethical approval for the study was obtained. Results 164 I-MAGs were provided for 75 patients with dysphagia (PWDs) in the two intervention wards. At discharge, 23 patients in the intervention wards and 7 patients in the control wards were approached for recruitment of which 17 (74%) & 5 (71.5%) respectively consented. Discussion Recruitment rates were low on discharge due to the dysphagia remitting during hospitalisation. The introduction of the I-MAG demonstrated no effect on the quality of administration on the intervention ward and interestingly practice improved on the control ward. The observation of medication rounds at least one month post I-MAG removal may have identified a reversal to normal practice and ideally observations should have been undertaken with I-MAGs in place. Identification of the reason for the improvement in the control ward is warranted.

Meltdown : a tool to help in the interpretation of thermal melt curves acquired by differential scanning fluorimetry

The output of a differential scanning fluorimetry (DSF) assay is a series of melt curves, which need to be interpreted to get value from the assay. An application that translates raw thermal melt curve data into more easily assimilated knowledge is described. This program, called “Meltdown,” conducts four main activities—control checks, curve normalization, outlier rejection, and melt temperature (Tm) estimation—and performs optimally in the presence of triplicate (or higher) sample data. The final output is a report that summarizes the results of a DSF experiment. The goal of Meltdown is not to replace human analysis of the raw fluorescence data but to provide a meaningful and comprehensive interpretation of the data to make this useful experimental technique accessible to inexperienced users, as well as providing a starting point for detailed analyses by more experienced users.

The development of virtual leaf surface models for interactive agrichemical spray applications

This project constructed virtual plant leaf surfaces from digitised data sets for use in droplet spray models. Digitisation techniques for obtaining data sets for cotton, chenopodium and wheat leaves are discussed and novel algorithms for the reconstruction of the leaves from these three plant species are developed. The reconstructed leaf surfaces are included into agricultural droplet spray models to investigate the effect of the nozzle and spray formulation combination on the proportion of spray retained by the plant. A numerical study of the post-impaction motion of large droplets that have formed on the leaf surface is also considered.

A finite element modelling method for thin layer mortared masonry systems

This paper deals with a finite element modelling method for thin layer mortared masonry systems. In this method, the mortar layers including the interfaces are represented using a zero thickness interface element and the masonry units are modelled using an elasto-plastic, damaging solid element. The interface element is formulated using two regimes; i) shear-tension and ii) shearcompression. In the shear-tension regime, the failure of joint is consiedered through an eliptical failure criteria and in shear-compression it is considered through Mohr Coulomb type failure criterion. An explicit integration scheme is used in an implicit finite element framework for the formulation of the interface element. The model is calibrated with an experimental dataset from thin layer mortared masonry prism subjected to uniaxial compression, a triplet subjected to shear loads a beam subjected to flexural loads and used to predict the response of thin layer mortared masonry wallettes under orthotropic loading. The model is found to simulate the behaviour of a thin layer mortated masonry shear wall tested under pre-compression and inplane shear quite adequately. The model is shown to reproduce the failure of masonry panels under uniform biaxial state of stresses.

High-throughput bone and cartilage micropellet manufacture, followed by assembly of micropellets into biphasic osteochondral tissue

Engineered biphasic osteochondral tissues may have utility in cartilage defect repair. As bone-marrow-derived mesenchymal stem/stromal cells (MSC) have the capacity to make both bone-like and cartilage-like tissues, they are an ideal cell population for use in the manufacture of osteochondral tissues. Effective differentiation of MSC to bone-like and cartilage-like tissues requires two unique medium formulations and this presents a challenge both in achieving initial MSC differentiation and in maintaining tissue stability when the unified osteochondral tissue is subsequently cultured in a single medium formulation. In this proof-of-principle study, we used an in-house fabricated microwell platform to manufacture thousands of micropellets formed from 166 MSC each. We then characterized the development of bone-like and cartilage-like tissue formation in the micropellets maintained for 8–14 days in sequential combinations of osteogenic or chondrogenic induction medium. When bone-like or cartilage-like micropellets were induced for only 8 days, they displayed significant phenotypic changes when the osteogenic or chondrogenic induction medium, respectively, was swapped. Based on these data, we developed an extended 14-day protocol for the pre-culture of bone-like and cartilage-like micropellets in their respective induction medium. Unified osteochondral tissues were formed by layering 12,000 osteogenic micropellets and 12,000 chondrogenic micropellets into a biphasic structure and then further culture in chondrogenic induction medium. The assembled tissue was cultured for a further 8 days and characterized via histology. The micropellets had amalgamated into a continuous structure with distinctive bone-like and cartilage-like regions. This proof-of-concept study demonstrates the feasibility of micropellet assembly for the formation of osteochondral-like tissues for possible use in osteochondral defect repair.

Incorporating process variability into stormwater quality modelling

Process variability in pollutant build-up and wash-off generates inherent uncertainty that affects the outcomes of stormwater quality models. Poor characterisation of process variability constrains the accurate accounting of the uncertainty associated with pollutant processes. This acts as a significant limitation to effective decision making in relation to stormwater pollution mitigation. The study undertaken developed three theoretical scenarios based on research findings that variations in particle size fractions <150µm and >150µm during pollutant build-up and wash-off primarily determine the variability associated with these processes. These scenarios, which combine pollutant build-up and wash-off processes that takes place on a continuous timeline, are able to explain process variability under different field conditions. Given the variability characteristics of a specific build-up or wash-off event, the theoretical scenarios help to infer the variability characteristics of the associated pollutant process that follows. Mathematical formulation of the theoretical scenarios enables the incorporation of variability characteristics of pollutant build-up and wash-off processes in stormwater quality models. The research study outcomes will contribute to the quantitative assessment of uncertainty as an integral part of the interpretation of stormwater quality modelling outcomes.

National Profiles of In-Country Capacity to Support Disability-Inclusive Education; Fiji, Samoa, Soloman Islands and Vanuatu

This publication emanates from the four-country research project entitled “Strengthening capacity for disability-inclusive education development policy formulation, implementation and monitoring in the South Pacific region” funded by the Australian Development Research Award Scheme (ADRAS) and conducted jointly by the academic staff from the Queensland University of Technology and the University of the South Pacific.

Mobilising School and Community Engagement to Implement Disability-Inclusive Education through Action Research: Fiji, Samoa, Solomon Islands and Vanuatu

This publication emanates from the four-country research project entitled “Strengthening capacity for disability-inclusive education development policy formulation, implementation and monitoring in the South Pacific region” funded by the Australian Development Research Award Scheme (ADRAS) and conducted jointly by the academic staff from the Queensland University of Technology and the University of the South Pacific.

A dynamic real time scheduling methodology for the emergency department

This project constructs a scheduling solution for the Emergency Department. The schedules are generated in real-time to adapt to new patient arrivals and changing conditions. An integrated scheduling formulation assigns patients to beds and treatment tasks to resources. The schedule efficiency is assessed using waiting time and total care time experienced by patients. The solution algorithm incorporates dispatch rules, meta-heuristics and a new extended disjunctive graph formulation which provide high quality solutions in a fast time-frame for real time decision support. This algorithm can be implemented in an electronic patient management system to improve patient flow in the Emergency Department.

Nonlinear analysis for the pre- and post-yield behaviour of a hybrid structure by a higher-order element with the refined plastic hinge approach

Efficient and accurate geometric and material nonlinear analysis of the structures under ultimate loads is a backbone to the success of integrated analysis and design, performance-based design approach and progressive collapse analysis. This paper presents the advanced computational technique of a higher-order element formulation with the refined plastic hinge approach which can evaluate the concrete and steel-concrete structure prone to the nonlinear material effects (i.e. gradual yielding, full plasticity, strain-hardening effect when subjected to the interaction between axial and bending actions, and load redistribution) as well as the nonlinear geometric effects (i.e. second-order P-d effect and P-D effect, its associate strength and stiffness degradation). Further, this paper also presents the cross-section analysis useful to formulate the refined plastic hinge approach.

Stone baby: An exploration of trembling and its potential for visual art

Informed by Kristeva's formulation of affect and Winnicott's Holding Environment, this practice-led visual art project is an exploration into how sensitivity to the physical sensation of trembling can sustain a creative practice. Building upon this is a further enquiry into what the significance of the affective experience of trembling is for an ethics of affect in contemporary art. I have done this through object and video-based installations informed by my own experience of trembling. This has been further informed by the work of artists like Louise Bourgeois, Dennis Del Favero and Willie Doherty. The creative outcomes contribute to the discourse around ethical responses to affect by extending and developing on the works of these artists.

Green procurement framework for the Malaysian construction industry

Construction projects have a negative impact on the environment. As Malaysia is planning more construction projects to cater for its current and future development needs, practitioners are urged to undertake greener approaches to construction. One of the efforts is the introduction of green procurement, which is promoted under the Malaysian Government’s MyHijau initiative. Construction procurement is recognised as a tool to shift the construction business into a greener industry. However, the implementation of green procurement in Malaysia is still in its infancy and faces a number of challenges, such as the lack of knowledge. A significant gap has been found between policy formulation and actual project delivery as there are no practical guidelines for stakeholders to procure environmental-friendly construction projects. To address this problem, the present research (as part of an ongoing PhD project) aims to develop a green procurement framework that guides stakeholders in procuring green projects in Malaysia. This article highlights the concept of green procurement in Malaysia, the work carried out to date to achieve the research objectives and the preliminary framework that has been established. It is hoped that this research will help academics and practitioners to further explore the potential of green procurement to improve sustainability in the current construction industry practices.

The doctrine of necessity and the detention and restraint of people with intellectual impairment: Is there any justification?

In Australia, the legal basis for the detention and restraint of people with intellectual impairment is ad hoc and unclear. There is no comprehensive legal framework that authorises and regulates the detention of, for example, older people with dementia in locked wards or in residential aged care, people with disability in residential services or people with acquired brain injury in hospital and rehabilitation services. This paper focuses on whether the common law doctrine of necessity (or its statutory equivalents) should have a role in permitting the detention and restraint of people with disabilities. Traditionally, the defence of necessity has been recognised as an excuse, where the defendant, faced by a situation of imminent peril, is excused from the criminal or civil liability because of the extraordinary circumstances they find themselves in. In the United Kingdom, however, in In re F (Mental Patient: Sterilisation) and R v Bournewood Community and Mental Health NHS Trust, ex parte L, the House of Lords broadened the defence so that it operated as a justification for treatment, detention and restraint outside of the emergency context. This paper outlines the distinction between necessity as an excuse and as a defence, and identifies a number of concerns with the latter formulation: problems of democracy, integrity, obedience, objectivity and safeguards. Australian courts are urged to reject the United Kingdom approach and retain an excuse-based defence, as the risks of permitting the essentially utilitarian model of necessity as a justification are too great.