Vertical displacement measurement using fibre Bragg grating (FBG) sensors for structural health monitoring of bridges

This thesis developed a practical, cost effective, easy-to-use method for measuring the vertical displacements of bridges using fiber Bragg grating (FBG) sensors, which includes the curvature and inclination approaches. These approaches were validated by the numerical simulation tests on a full scale bridge and the laboratory-based tests. In doing so, a novel frictionless FBG inclination sensor with extremely high sensitivity and resolution has also been developed and validated.

Deterministic control of structural and optical properties of plasma-grown vertical graphene nanosheet networks via nitrogen gas variation

The effect of nitrogen on the growth of vertically oriented graphene nanosheets on catalyst-free silicon and glass substrates in a plasma-assisted process is studied. Different concentrations of nitrogen were found to act as versatile control knobs that could be used to tailor the length, number density and structural properties of the nanosheets. Nanosheets with different structural characteristics exhibit markedly different optical properties. The nanosheet samples were treated with a bovine serum albumin protein solution to investigate the effects of this variation on the optical properties for biosensing through confocal micro-Raman spectroscopy and UV-Vis spectrophotometry. © 2012 Optical Society of America.

Influence of jet inclination on structural loading in an experimentally simulated microburst

Steady and pulsed flow stationary impinging jets have been employed to simulate the wind field produced by a thunderstorm microburst. The effect on the low level wind field due to jet inclination with respect to the impingement surface has been studied. A single point velocity time history has been compared to the full-scale Andrews AFB microburst for model validation. It was found that for steady flow, jet inclination increased the radial extent of high winds but did not increase the magnitude of these winds when compared to the perpendicular impingement case. It was found that for inclined pulsed flow the design wind conditions could increase compared to perpendicular impingement. It was found that the location of peak winds was affected by varying the outlet conditions.

Composition-dependent structural and electronic properties of α-(Si1−xCx)3N4

The highly unusual structural and electronic properties of the α-phase of (Si1-xCx)3N4 are determined by density functional theory (DFT) calculations using the Generalized Gradient Approximation (GGA). The electronic properties of α-(Si 1-xCx)3N4 are found to be very close to those of α-C3N4. The bandgap of α-(Si 1-xCx)3N4 significantly decreases as C atoms are substituted by Si atoms (in most cases, smaller than that of either α-Si3N4 or α-C3N4) and attains a minimum when the ratio of C to Si is close to 2. On the other hand, the bulk modulus of α-(Si1-xCx)3N 4 is found to be closer to that of α-Si3N 4 than of α-C3N4. Plasma-assisted synthesis experiments of CNx and SiCN films are performed to verify the accuracy of the DFT calculations. TEM measurements confirm the calculated lattice constants, and FT-IR/XPS analysis confirms the formation and lengths of C-N and Si-N bonds. The results of DFT calculations are also in a remarkable agreement with the experiments of other authors.

Structural, optical and electrical properties of Al-doped ZnO transparent conducting oxide for solar cell applications

Al-doped zinc oxide (AZO) thin films are deposited onto glass substrates using radio-frequency reactive magnetron sputtering and the improvements in their physical properties by post-synthesis thermal treatment are reported. X-ray diffraction spectra show that the structure of films can be controlled by adjusting the annealing temperatures, with the best crystallinity obtained at 400°C under a nitrogen atmosphere. These films exhibit improved quality and better optical transmittance as indicated by the UV-Vis spectra. Furthermore, the sheet resistivity is found to decrease from 1.87 × 10-3 to 5.63 × 10-4Ω⋅cm and the carrier mobility increases from 6.47 to 13.43 cm2 ⋅ V-1 ⋅ s-1 at the optimal annealing temperature. Our results demonstrate a simple yet effective way in controlling the structural, optical and electrical properties of AZO thin films, which is important for solar cell applications.

Structural, electronic, and optical properties of wurtzite and rocksalt InN under pressure

Structural stability, electronic, and optical properties of InN under high pressure are studied using the first-principles calculations. The lattice constants and electronic band structure are found consistent with the available experimental and theoretical values. The pressure of the wurtzite-to-rocksalt structural transition is 13.4 GPa, which is in an excellent agreement with the most recent experimental values. The optical characteristics reproduce the experimental data thus justifying the feasibility of our theoretical predictions of the optical properties of InN at high pressures.

The transformation of bureaucracy? Structural change in the Commonwealth public service 1983-93

Commentators have predicted bureaucratic organisations would undergo substantial change as a result of social and economic pressures. We ask whether reforms to the Australian public service over the 1983–93 period exemplify this process. We use the methods of organisational analysis to characterise the direction of change, basing our assessment on the standard structural variables of complexity, formalisation and centralisation, together with a cultural variable. We find evidence that, overall, departments of state in the APS were becoming less bureaucratic in their structure, culture and internal function in the 1983–93 period. However, the effect was not uniform across departments, or unambiguous — formalisation, for example, increased in some respects and decreased in others. Centralisation increased overall, despite devolution of some decision-making.

Structural evolution of nanocrystalline silicon thin films synthesized in high-density, low-temperature reactive plasmas

Silicon thin films with a variable content of nanocrystalline phase were deposited on single-crystal silicon and glass substrates by inductively coupled plasma-assisted chemical vapor deposition using a silane precursor without any hydrogen dilution in the low substrate temperature range from 100 to 300 °C. The structural and optical properties of the deposited films are systematically investigated by Raman spectroscopy, x-ray diffraction, Fourier transform infrared absorption spectroscopy, UV/vis spectroscopy, scanning electron microscopy and high-resolution transmission electron microscopy. It is shown that the structure of the silicon thin films evolves from the purely amorphous phase to the nanocrystalline phase when the substrate temperature is increased from 100 to 150 °C. It is found that the variations of the crystalline fraction fc, bonded hydrogen content CH, optical bandgap ETauc, film microstructure and growth rate Rd are closely related to the substrate temperature. In particular, at a substrate temperature of 300 °C, the nanocrystalline Si thin films of our interest feature a high growth rate of 1.63nms-1, a low hydrogen content of 4.0at.%, a high crystalline fraction of 69.1%, a low optical bandgap of 1.55eV and an almost vertically aligned columnar structure with a mean grain size of approximately 10nm. It is also shown that the low-temperature synthesis of nanocrystalline Si thin films without any hydrogen dilution is attributed to the outstanding dissociation ability of the high-density inductively coupled plasmas and effective plasma-surface interactions during the growth process. Our results offer a highly effective yet simple and environmentally friendly technique to synthesize high-quality nanocrystalline Si films, vitally needed for the development of new-generation solar cells and other emerging nanotechnologies.

Synthesis and structural properties of Al-C-N-O composite thin films

Al-C-N-O composite thin films have been synthesized by radio frequency reactive diode sputtering of an aluminum target in plasmas of N2+O2+CH4 gas mixtures. The chemical structure and composition of the films have been investigated by means of infrared and X-ray photoelectron spectroscopy. The results reveal the formation of C-N, Al-C, Al-N and Al-O bonds. The X-ray diffraction pattern suggests that the films are of nanometer composite material and contain predominately crystalline grains of hexagonal AlN and α-Al2O3. A good thermal stability of the composite has been confirmed by the annealing treatment at temperatures up to 600 °C.

A coupled SPH-DEM model for micro-scale structural deformations of plant cells during drying

A single plant cell was modeled with smoothed particle hydrodynamics (SPH) and a discrete element method (DEM) to study the basic micromechanics that govern the cellular structural deformations during drying. This two-dimensional particle-based model consists of two components: a cell fluid model and a cell wall model. The cell fluid was approximated to a highly viscous Newtonian fluid and modeled with SPH. The cell wall was treated as a stiff semi-permeable solid membrane with visco-elastic properties and modeled as a neo-Hookean solid material using a DEM. Compared to existing meshfree particle-based plant cell models, we have specifically introduced cell wall–fluid attraction forces and cell wall bending stiffness effects to address the critical shrinkage characteristics of the plant cells during drying. Also, a moisture domain-based novel approach was used to simulate drying mechanisms within the particle scheme. The model performance was found to be mainly influenced by the particle resolution, initial gap between the outermost fluid particles and wall particles and number of particles in the SPH influence domain. A higher order smoothing kernel was used with adaptive smoothing length to improve the stability and accuracy of the model. Cell deformations at different states of cell dryness were qualitatively and quantitatively compared with microscopic experimental findings on apple cells and a fairly good agreement was observed with some exceptions. The wall–fluid attraction forces and cell wall bending stiffness were found to be significantly improving the model predictions. A detailed sensitivity analysis was also done to further investigate the influence of wall–fluid attraction forces, cell wall bending stiffness, cell wall stiffness and the particle resolution. This novel meshfree based modeling approach is highly applicable for cellular level deformation studies of plant food materials during drying, which characterize large deformations.

Engineering the mechanical properties of graphene nanotube hybrid structures through structural modulation

The excellent multi-functional properties of carbon nanotube (CNT) and graphene have enabled them as appealing building blocks to construct 3D carbon-based nanomaterials or nanostructures. The recently reported graphene nanotube hybrid structure (GNHS) is one of the representatives of such nanostructures. This work investigated the relationships between the mechanical properties of the GNHS and its structure basing on large-scale molecular dynamics simulations. It is found that increasing the length of the constituent CNTs, the GNHS will have a higher Young’s modulus and yield strength. Whereas, no strong correlation is found between the number of graphene layers and Young’s modulus and yield strength, though more graphene layers intends to lead to a higher yield strain. In the meanwhile, the presences of multi-wall CNTs are found to greatly strengthen the hybrid structure. Generally, the hybrid structures exhibit a brittle behavior and the failure initiates from the connecting regions between CNT and graphene. More interestingly, affluent formations of monoatomic chains and rings are found at the fracture region. This study provides an in-depth understanding of the mechanical performance of the GNHSs while varying their structures, which will shed lights on the design and also the applications of the carbon-based nanostructures.

In pursuit of an architecture realism

The noble idea of studying seminal works to ‘see what we can learn’ has turned in the 1990s into ‘let’s see what we can take’ and in the last decade a more toxic derivative ‘what else can’t we take’. That is my observation as a student of architecture in the 1990s, and as a practitioner in the 2000s. In 2010, the sense that something is ending is clear. The next generation is rising and their gaze has shifted. The idea of classification (as a means of separation) was previously rejected by a generation of Postmodernists; the usefulness of difference declined. It’s there in the presence of plurality in the resulting architecture, a decision to mine history and seize in a willful manner. This is a process of looking back but never forward. It has been a mono-culture of absorption. The mono-culture rejected the pursuit of the realistic. It is a blanket suffocating all practice of architecture in this country from the mercantile to the intellectual. Independent reviews of Australia’s recent contributions to the Venice Architecture Biennales confirm the malaise. The next generation is beginning to reconsider classification as a means of unification. By acknowledging the characteristics of competing forces it is possible to bring them into a state of tension. Seeking a beautiful contrast is a means to a new end. In the political setting, this is described by Noel Pearson as the radical centre[1]. The concept transcends the political and in its most essential form is a cultural phenomenon. It resists the compromised position and suggests that we can look back while looking forward. The radical centre is the only demonstrated opportunity where it is possible to pursue a realistic architecture. A realistic architecture in Australia may be partially resolved by addressing our anxiety of permanence. Farrelly’s built desires[2] and Markham’s ritual demonstrations[3] are two ways into understanding the broader spectrum of permanence. But I think they are downstream of our core problem. Our problem, as architects, is that we are yet to come to terms with this place. Some call it landscape others call it country. Australian cities were laid out on what was mistaken for a blank canvas. On some occasions there was the consideration of the landscape when it presented insurmountable physical obstacles. The architecture since has continued to work on its piece of a constantly blank canvas. Even more ironic is the commercial awards programs that represent a claim within this framework but at best can only establish a dialogue within itself. This is a closed system unable to look forward. It is said that Melbourne is the most European city in the southern hemisphere but what is really being described there is the limitation of a senseless grid. After all, if Dutch landscape informs Dutch architecture why can’t the Australian landscape inform Australian architecture? To do that, we would have to acknowledge our moribund grasp of the meaning of the Australian landscape. Or more precisely what Indigenes call Country[4]. This is a complex notion and there are different ways into it. Country is experienced and understood through the senses and seared into memory. If one begins design at that starting point it is not unreasonable to think we can arrive at an end point that is a counter trajectory to where we have taken ourselves. A recent studio with Masters students confirmed this. Start by finding Country and it would be impossible to end up with a building looking like an Aboriginal man’s face. To date architecture in Australia has overwhelmingly ignored Country on the back of terra nullius. It can’t seem to get past the picturesque. Why is it so hard? The art world came to terms with this challenge, so too did the legal establishment, even the political scene headed into new waters. It would be easy to blame the budgets of commerce or the constraints of program or even the pressure of success. But that is too easy. Those factors are in fact the kind of limitations that opportunities grow out of. The past decade of economic plenty has, for the most part, smothered the idea that our capitals might enable civic settings or an architecture that is able to looks past lot line boundaries in a dignified manner. The denied opportunities of these settings to be prompted by the Country they occupy is criminal. The public realm is arrested in its development because we refuse to accept Country as a spatial condition. What we seem to be able to embrace is literal and symbolic gestures usually taking the form of a trumped up art installations. All talk – no action. To continue to leave the public realm to the stewardship of mercantile interests is like embracing derivative lending after the global financial crisis.Herein rests an argument for why we need a resourced Government Architect’s office operating not as an isolated lobbyist for business but as a steward of the public realm for both the past and the future. New South Wales is the leading model with Queensland close behind. That is not to say both do not have flaws but current calls for their cessation on the grounds of design parity poorly mask commercial self interest. In Queensland, lobbyists are heavily regulated now with an aim to ensure integrity and accountability. In essence, what I am speaking of will not be found in Reconciliation Action Plans that double as business plans, or the mining of Aboriginal culture for the next marketing gimmick, or even discussions around how to make buildings more ‘Aboriginal’. It will come from the next generation who reject the noxious mono-culture of absorption and embrace a counter trajectory to pursue an architecture of realism.

Structural and functional characterization of three DsbA Paralogues from Salmonella enterica Serovar Typhimurium

In prototypic Escherichia coli K-12 the introduction of disulfide bonds into folding proteins is mediated by the Dsb family of enzymes, primarily through the actions of the highly oxidizing protein EcDsbA. Homologues of the Dsb catalysts are found in most bacteria. Interestingly, pathogens have developed distinct Dsb machineries that play a pivotal role in the biogenesis of virulence factors, hence contributing to their pathogenicity. Salmonella enterica serovar (sv.) Typhimurium encodes an extended number of sulfhydryl oxidases, namely SeDsbA, SeDsbL, and SeSrgA. Here we report a comprehensive analysis of the sv. Typhimurium thiol oxidative system through the structural and functional characterization of the three Salmonella DsbA paralogues. The three proteins share low sequence identity, which results in several unique three-dimensional characteristics, principally in areas involved in substrate binding and disulfide catalysis. Furthermore, the Salmonella DsbA-like proteins also have different redox properties. Whereas functional characterization revealed some degree of redundancy, the properties of SeDsbA, SeDsbL, and SeSrgA and their expression pattern in sv. Typhimurium indicate a diverse role for these enzymes in virulence.