Technology : new horizons in teaching law

17.1 Up until the 1990s the methods used to teach the law had evolved little since the first law schools were established in Australia. As Keyes and Johnstone observed: In the traditional model, most teachers uncritically replicate the learning experiences that they had when students, which usually means that the dominant mode of instruction is reading lecture notes to large classes in which students are largely passive. Traditional legal education has been described in the following terms: Traditionally law is taught through a series of lectures, with little or no student involvement, and a tutorial programme. Sometimes tutorials are referred to as seminars but the terminology used is often insignificant: both terms refer to probably the only form of student participation that takes place throughout these students‘ academic legal education. The tutorial consists of analysing the answers, prepared in advanced (sic), to artificial Janet and John Doe problems or esoteric essay questions. The primary focus of traditional legal education is the transmission of content knowledge, more particularly the teaching of legal rules, especially those drawn from case law. This approach has a long pedigree. Writing in 1883, Dicey proposed that nothing can be taught to students of greater value, either intellectually or for the purposes of legal practice, than the habit of looking on the law as a series of rules‘.

Ocular characteristics in myopic anisometropia

PURPOSE: To investigate the interocular symmetry of ocular optical, biometric and biomechanical characteristics between the more and less ametropic eyes of myopic anisometropes. METHODS: Thirty-four young, healthy myopic anisometropic adults (≥ 1 D spherical equivalent difference between eyes) without amblyopia or strabismus were recruited. A range of biometric and optical parameters were measured in the more and less ametropic eye of each subject including; axial length, ocular aberrations, intraocular pressure and corneal topography, thickness and biomechanics. Morphology of the anterior eye in primary and downward gaze was examined using custom software analysis of high resolution digital images. Ocular sighting dominance was assessed using the hole-in-the-card test. RESULTS: Mean absolute spherical equivalent anisometropia was 1.74 ± 0.74 D. There was a strong correlation between the degree of anisometropia and the interocular difference in axial length (r = 0.81, p < 0.001). The more and less ametropic fellow eyes displayed a high degree of interocular symmetry for the majority of biometric, biomechanical and optical parameters measured. When the level of anisometropia exceeded 1.75 D (n = 10), the more myopic eye was the dominant sighting eye in nine of these ten subjects. Subjects with greater levels of anisometropia (> 1.75 D) also showed high levels of correlation between the dominant and non-dominant eyes in their biometric, biomechanical and optical characteristics. CONCLUSIONS: Although significantly different in axial length, anisometropic eyes display a high degree of interocular symmetry for a range of anterior eye biometrics and optical parameters. For higher levels of anisometropia, the more myopic eye tends to be the dominant sighting eye.

Caseload management, work-related stress and case manager self-efficacy among Victorian mental health case managers

Objective: In Australia and comparable countries, case management has become the dominant process by which public mental health services provide outpatient clinical services to people with severe mental illness. There is recognition that caseload size impacts on service provision and that management of caseloads is an important dimension of overall service management. There has been little empirical investigation, however, of caseload and its management. The present study was undertaken in the context of an industrial agreement in Victoria, Australia that required services to introduce standardized approaches to caseload management. The aims of the present study were therefore to (i) investigate caseload size and approaches to caseload management in Victoria's mental health services; and (ii) determine whether caseload size and/or approach to caseload management is associated with work-related stress or case manager self-efficacy among community mental health professionals employed in Victoria's mental health services. Method: A total of 188 case managers responded to an online cross-sectional survey with both purpose-developed items investigating methods of case allocation and caseload monitoring, and standard measures of work-related stress and case manager personal efficacy. Results: The mean caseload size was 20 per full-time case manager. Both work-related stress scores and case manager personal efficacy scores were broadly comparable with those reported in previous studies. Higher caseloads were associated with higher levels of work-related stress and lower levels of case manager personal efficacy. Active monitoring of caseload was associated with lower scores for work-related stress and higher scores for case manager personal efficacy, regardless of size of caseload. Although caseloads were most frequently monitored by the case manager, there was evidence that monitoring by a supervisor was more beneficial than self-monitoring. Conclusion: Routine monitoring of caseload, especially by a workplace supervisor, may be effective in reducing work-related stress and enhancing case manager personal efficacy. Keywords: case management, caseload, stress

Bispectral and trispectral characterization of transition to chaos in the Duffing oscillator

Higher-order spectral (bispectral and trispectral) analyses of numerical solutions of the Duffing equation with a cubic stiffness are used to isolate the coupling between the triads and quartets, respectively, of nonlinearly interacting Fourier components of the system. The Duffing oscillator follows a period-doubling intermittency catastrophic route to chaos. For period-doubled limit cycles, higher-order spectra indicate that both quadratic and cubic nonlinear interactions are important to the dynamics. However, when the Duffing oscillator becomes chaotic, global behavior of the cubic nonlinearity becomes dominant and quadratic nonlinear interactions are weak, while cubic interactions remain strong. As the nonlinearity of the system is increased, the number of excited Fourier components increases, eventually leading to broad-band power spectra for chaos. The corresponding higher-order spectra indicate that although some individual nonlinear interactions weaken as nonlinearity increases, the number of nonlinearly interacting Fourier modes increases. Trispectra indicate that the cubic interactions gradually evolve from encompassing a few quartets of Fourier components for period-1 motion to encompassing many quartets for chaos. For chaos, all the components within the energetic part of the power spectrum are cubically (but not quadratically) coupled to each other.

Bullying : the moral and social orders at play

This special issue came about following an international symposium on bullying held in December 2008 at the Department of Child Studies, Linko¨ping University, Sweden, led by Jakob Cromdal and Paul Horton. The articles represent a diverse body of theoretical and empirical work that emphasises children and young people’s views of and participation in everyday experiences. The articles, as a collection, aim to be provocative in terms of challenging some existing dominant understandings about bullying to propose alternate ways to understand this phenomenon.

Corporate governance mechanisms and earnings management in transitional countries – evidence from Chinese listed firms

The objective of this thesis is to investigate whether the corporate governance practices adopted by Chinese listed firms are associated with the quality of earnings information. Based on a review of agency and institutional theory, this study develops hypotheses that predict the monitoring effectiveness of the board and the audit committee. Using a combination of univariate and multivariate analyses, the association between corporate governance mechanisms and earnings management are tested from 2004 to 2008. Through analysing the empirical results, a number of findings are summarised as below. First, board independence is weakened by the introduction of government officials as independent directors on the boards. Government officials acting as independent directors, claim that they meet the definition of independent director set by the regulation. However, they have some connection with the State, which is the controlling shareholder in listed SOEs affiliated companies. Consequently, the effect of the independent director’s expertise in constraining earnings management is mitigated as demonstrated by an insignificant association between board expertise and earnings management. An alternative explanation for the inefficiency of board independence may point to the pre-selection of independent directors by the powerful CEO. It is argued that a CEO can manipulate the board composition and choose the "desirable" independent directors to monitor themselves. Second, a number of internal mechanisms, such as board size, board activities, and the separation of the roles of the CEO and chair are found to be significantly associated with discretionary accruals. This result suggests that there are advantages in having a large and active board in the Chinese setting. This can offset the disadvantages associated with large boards, such as increased bureaucracy, and hence, increase the constraining effects of a large and resourceful board. Third, factor analysis identifies two factors: CEO power and board power. CEO power is the factor which consists of CEO duality and turnover, and board power is composed of board size and board activity. The results of CEO power show that if a Chinese listed company has CEO duality and turnover at the same time, it is more likely to have a high level of earnings management. The significant and negative relationship between board power and accruals indicate that large boards with frequent meetings can be associated with low level of earnings management. Overall, the factor analysis suggests that certain governance mechanisms complement each other to become more efficient monitors of opportunistic earnings management. A combination of board characteristics can increase the negative association with earnings management. Fourth, the insignificant results between audit committees and earnings management in Chinese listed firms suggests that the Chinese regulator should strengthen the audit committee functions. This thesis calls for listed firms to disclose more information on audit committee composition and activities, which can facilitate future research on the Chinese audit committee’s monitoring role. Fifth, the interactive results between State ownership and board characteristics show that dominant State ownership has a moderating effect on board monitoring power as the State totally controls 42% of the issued shares. The high percentage of State ownership makes it difficult for the non-controlling institutional shareholders to challenge the State’s dominant status. As a result, the association between non-controlling institutional ownership and earnings management is insignificant in most situations. Lastly, firms audited by the international Big4 have lower abnormal accruals than firms audited by domestic Chinese audit firms. In addition, the inverse U-shape relationship between audit tenure and earnings quality demonstrates the changing effects of audit quality after a certain period of appointment. Furthermore, this thesis finds that listing in Hong Kong Stock Exchanges can be an alternative governance mechanism to discipline Chinese firms to follow strict Hong Kong listing requirements. Management of Hong Kong listed companies are exposed to the scrutiny of international investors and Hong Kong regulators. This in turn reduces their chances of conducting self-interested earnings manipulation. This study is designed to fill the gap in governance literature in China that is related to earnings management. Previous research on corporate governance mechanisms and earnings management in China is not conclusive. The current research builds on previous literature and provides some meaningful implications for practitioners, regulators, academic, and international investors who have investment interests in a transitional country. The findings of this study contribute to corporate governance and earnings management literature in the context of the transitional economy of China. The use of alternative measures for earnings management yields similar results compared with the accruals models and produces additional findings.

YouTube

Originally launched in 2005 with a focus on user-generated content, YouTube has become the dominant platform for online video worldwide, and an important location for some of the most significant trends and controversies in the contemporary new-media environment. Throughout its very short history, it has also intersected with and been the focus of scholarly debates related to the politics, economics, and cultures of the new media—in particular, the “participatory turn” associated with “Web 2.0” business models’ partial reliance on amateur content and social networking. Given the slow pace of traditional scholarly publishing, the body of media and cultural studies literature substantively dedicated to describing and critically understanding YouTube’s texts, practices, and politics is still small, but it is growing steadily. At the same time, since its inception scholars from a wide range of disciplines and critical perspectives have found YouTube useful as a source of examples and case studies, some of which are included here; others have experimented directly with the scholarly and educational potential of the platform itself. For these reasons, although primarily based around the traditional publishing outlets for media, Internet, and cultural studies, this bibliography draws eclectically on a wide range of sources—including sources very closely associated with the web business literature and with the YouTube community itself.

Effects of climate change on the wash-off of volatile organic compounds from urban roads

The predicted changes in rainfall characteristics due to climate change could adversely affect stormwater quality in highly urbanised coastal areas throughout the world. This in turn will exert a significant influence on the discharge of pollutants to estuarine and marine waters. Hence, an in-depth analysis of the effects of such changes on the wash-off of volatile organic compounds (VOCs) from urban roads in the Gold Coast region in Australia was undertaken. The rainfall characteristics were simulated using a rainfall simulator. Principal Component Analysis (PCA) and Multicriteria Decision tools such as PROMETHEE and GAIA were employed to understand the VOC wash-off under climate change. It was found that low, low to moderate and high rain events due to climate change will affect the wash-off of toluene, ethylbenzene, meta-xylene, para-xylene and ortho-xylene from urban roads in Gold Coast. Total organic carbon (TOC) was identified as predominant carrier of toluene, meta-xylene and para-xylene in <1µm to 150µm fractions and for ethylbenzene in 150µm to >300µm fractions under such dominant rain events due to climate change. However, ortho-xylene did not show such affinity towards either TOC or TSS (total suspended solids) under the simulated climatic conditions.

An advanced meshless method for time fractional diffusion equation

Recently, because of the new developments in sustainable engineering and renewable energy, which are usually governed by a series of fractional partial differential equations (FPDEs), the numerical modelling and simulation for fractional calculus are attracting more and more attention from researchers. The current dominant numerical method for modeling FPDE is Finite Difference Method (FDM), which is based on a pre-defined grid leading to inherited issues or shortcomings including difficulty in simulation of problems with the complex problem domain and in using irregularly distributed nodes. Because of its distinguished advantages, the meshless method has good potential in simulation of FPDEs. This paper aims to develop an implicit meshless collocation technique for FPDE. The discrete system of FPDEs is obtained by using the meshless shape functions and the meshless collocation formulation. The stability and convergence of this meshless approach are investigated theoretically and numerically. The numerical examples with regular and irregular nodal distributions are used to validate and investigate accuracy and efficiency of the newly developed meshless formulation. It is concluded that the present meshless formulation is very effective for the modeling and simulation of fractional partial differential equations.

Deformation behaviours of coarse-grained and nanocrystalline Mg-5wt% Al alloys

Magnesium alloys have been of growing interest to various engineering applications, such as the automobile, aerospace, communication and computer industries due to their low density, high specific strength, good machineability and availability as compared with other structural materials. However, most Mg alloys suffer from poor plasticity due to their Hexagonal Close Packed structure. Grain refinement has been proved to be an effective method to enhance the strength and alter the ductility of the materials. Several methods have been proposed to produce materials with nanocrystalline grain structures. So far, most of the research work on nanocrystalline materials has been carried out on Face-Centered Cubic and Body-Centered Cubic metals. However, there has been little investigation of nanocrystalline Mg alloys. In this study, bulk coarse-grained and nanocrystalline Mg alloys were fabricated by a mechanical alloying method. The mixed powder of Mg chips and Al powder was mechanically milled under argon atmosphere for different durations of 0 hours (MA0), 10 hours (MA10), 20 hours (MA20), 30 hours (MA30) and 40 hours (MA40), followed by compaction and sintering. Then the sintered billets were hot-extruded into metallic rods with a 7 mm diameter. The obtained Mg alloys have a nominal composition of Mg–5wt% Al, with grain sizes ranging from 13 μm down to 50 nm, depending on the milling durations. The microstructure characterization and evolution after deformation were carried out by means of Optical microscopy, X-Ray Diffraction, Scanning Electron Microscopy, Transmission Electron Microscopy, Scanning Probe Microscopy and Neutron Diffraction techniques. Nanoindentaion, compression and micro-compression tests on micro-pillars were used to study the size effects on the mechanical behaviour of the Mg alloys. Two kinds of size effects on the mechanical behaviours and deformation mechanisms were investigated: grain size effect and sample size effect. The nanoindentation tests were composed of constant strain rate, constant loading rate and indentation creep tests. The normally reported indentation size effect in single crystal and coarse-grained crystals was observed in both the coarse-grained and nanocrystalline Mg alloys. Since the indentation size effect is correlated to the Geometrically Necessary Dislocations under the indenter to accommodate the plastic deformation, the good agreement between the experimental results and the Indentation Size Effect model indicated that, in the current nanocrystalline MA20 and MA30, the dislocation plasticity was still the dominant deformation mechanism. Significant hardness enhancement with decreasing grain size, down to 58 nm, was found in the nanocrystalline Mg alloys. Further reduction of grain size would lead to a drop in the hardness values. The failure of grain refinement strengthening with the relatively high strain rate sensitivity of nanocrystalline Mg alloys suggested a change in the deformation mechanism. Indentation creep tests showed that the stress exponent was dependent on the loading rate during the loading section of the indentation, which was related to the dislocation structures before the creep starts. The influence of grain size on the mechanical behaviour and strength of extruded coarse-grained and nanocrystalline Mg alloys were investigated using uniaxial compression tests. The macroscopic response of the Mg alloys transited from strain hardening to strain softening behaviour, with grain size reduced from 13 ìm to 50 nm. The strain hardening was related to the twinning induced hardening and dislocation hardening effect, while the strain softening was attributed to the localized deformation in the nanocrystalline grains. The tension–compression yield asymmetry was noticed in the nanocrystalline region, demonstrating the twinning effect in the ultra-fine-grained and nanocrystalline region. The relationship k tensions < k compression failed in the nanocrystalline Mg alloys; this was attributed to the twofold effect of grain size on twinning. The nanocrystalline Mg alloys were found to exhibit increased strain rate sensitivity with decreasing grain size, with strain rate ranging from 0.0001/s to 0.01/s. Strain rate sensitivity of coarse-grained MA0 was increased by more than 10 times in MA40. The Hall-Petch relationship broke down at a critical grain size in the nanocrystalline region. The breakdown of the Hall-Petch relationship and the increased strain rate sensitivity were due to the localized dislocation activities (generalization and annihilation at grain boundaries) and the more significant contribution from grain boundary mediated mechanisms. In the micro-compression tests, the sample size effects on the mechanical behaviours were studied on MA0, MA20 and MA40 micro-pillars. In contrast to the bulk samples under compression, the stress-strain curves of MA0 and MA20 micro-pillars were characterized with a number of discrete strain burst events separated by nearly elastic strain segments. Unlike MA0 and MA20, the stress-strain curves of MA40 micro-pillars were smooth, without obvious strain bursts. The deformation mechanisms of the MA0 and MA20 micro-pillars under micro-compression tests were considered to be initially dominated by deformation twinning, followed by dislocation mechanisms. For MA40 pillars, the deformation mechanisms were believed to be localized dislocation activities and grain boundary related mechanisms. The strain hardening behaviours of the micro-pillars suggested that the grain boundaries in the nanocrystalline micro-pillars would reduce the source (nucleation sources for twins/dislocations) starvation hardening effect. The power law relationship of the yield strength on pillar dimensions in MA0, MA20 supported the fact that the twinning mechanism was correlated to the pre-existing defects, which can promote the nucleation of the twins. Then, we provided a latitudinal comparison of the results and conclusions derived from the different techniques used for testing the coarse-grained and nanocrystalline Mg alloy; this helps to better understand the deformation mechanisms of the Mg alloys as a whole. At the end, we summarized the thesis and highlighted the conclusions, contributions, innovations and outcomes of the research. Finally, it outlined recommendations for future work.

Physical characteristics of small ions and their interaction with ultrafine particles in the urban environment

In recent years, the effect of ions and ultrafine particles on ambient air quality and human health has been well documented, however, knowledge about their sources, concentrations and interactions within different types of urban environments remains limited. This thesis presents the results of numerous field studies aimed at quantifying variations in ion concentration with distance from the source, as well as identifying the dynamics of the particle ionisation processes which lead to the formation of charged particles in the air. In order to select the most appropriate measurement instruments and locations for the studies, a literature review was also conducted on studies that reported ion and ultrafine particle emissions from different sources in a typical urban environment. The initial study involved laboratory experiments on the attachment of ions to aerosols, so as to gain a better understanding of the interaction between ions and particles. This study determined the efficiency of corona ions at charging and removing particles from the air, as a function of different particle number and ion concentrations. The results showed that particle number loss was directly proportional to particle charge concentration, and that higher small ion concentrations led to higher particle deposition rates in all size ranges investigated. Nanoparticles were also observed to decrease with increasing particle charge concentration, due to their higher Brownian mobility and subsequent attachment to charged particles. Given that corona discharge from high voltage powerlines is considered one of the major ion sources in urban areas, a detailed study was then conducted under three parallel overhead powerlines, with a steady wind blowing in a perpendicular direction to the lines. The results showed that large sections of the lines did not produce any corona at all, while strong positive emissions were observed from discrete components such as a particular set of spacers on one of the lines. Measurements were also conducted at eight upwind and downwind points perpendicular to the powerlines, spanning a total distance of about 160m. The maximum positive small and large ion concentrations, and DC electric field were observed at a point 20 m downwind from the lines, with median values of 4.4×103 cm-3, 1.3×103 cm-3 and 530 V m-1, respectively. It was estimated that, at this point, less than 7% of the total number of particles was charged. The electrical parameters decreased steadily with increasing downwind distance from the lines but remained significantly higher than background levels at the limit of the measurements. Moreover, vehicles are one of the most prevalent ion and particle emitting sources in urban environments, and therefore, experiments were also conducted behind a motor vehicle exhaust pipe and near busy motorways, with the aim of quantifying small ion and particle charge concentration, as well as their distribution as a function of distance from the source. The study found that approximately equal numbers of positive and negative ions were observed in the vehicle exhaust plume, as well as near motorways, of which heavy duty vehicles were believed to be the main contributor. In addition, cluster ion concentration was observed to decrease rapidly within the first 10-15 m from the road and ion-ion recombination and ion-aerosol attachment were the most likely cause of ion depletion, rather than dilution and turbulence related processes. In addition to the above-mentioned dominant ion sources, other sources also exist within urban environments where intensive human activities take place. In this part of the study, airborne concentrations of small ions, particles and net particle charge were measured at 32 different outdoor sites in and around Brisbane, Australia, which were classified into seven different groups as follows: park, woodland, city centre, residential, freeway, powerlines and power substation. Whilst the study confirmed that powerlines, power substations and freeways were the main ion sources in an urban environment, it also suggested that not all powerlines emitted ions, only those with discrete corona discharge points. In addition to the main ion sources, higher ion concentrations were also observed environments affected by vehicle traffic and human activities, such as the city centre and residential areas. A considerable number of ions were also observed in a woodland area and it is still unclear if they were emitted directly from the trees, or if they originated from some other local source. Overall, it was found that different types of environments had different types of ion sources, which could be classified as unipolar or bipolar particle sources, as well as ion sources that co-exist with particle sources. In general, fewer small ions were observed at sites with co-existing sources, however particle charge was often higher due to the effect of ion-particle attachment. In summary, this study quantified ion concentrations in typical urban environments, identified major charge sources in urban areas, and determined the spatial dispersion of ions as a function of distance from the source, as well as their controlling factors. The study also presented ion-aerosol attachment efficiencies under high ion concentration conditions, both in the laboratory and in real outdoor environments. The outcomes of these studies addressed the aims of this work and advanced understanding of the charge status of aerosols in the urban environment.

Interocular symmetry in myopic anisometropia

Purpose: To investigate the interocular symmetry of optical, biometric and biomechanical characteristics between the fellow eyes of myopic anisometropes. Methods: Thirty-four young, healthy myopic anisometropic adults (≥ 1 D spherical equivalent difference between eyes) without amblyopia or strabismus were recruited. A range of biometric and optical parameters were measured in both eyes of each subject including; axial length, ocular aberrations, intraocular pressure (IOP), corneal topography and biomechanics. Ocular sighting dominance was also measured. Results: Mean absolute spherical equivalent anisometropia was 1.70 ± 0.74 D and there was a strong correlation between the degree of anisometropia and the interocular difference in axial length (r = 0.81, p < 0.001). The more and less myopic eyes displayed a high degree of interocular symmetry for the majority of biometric, biomechanical and optical parameters measured. When the level of anisometropia exceeded 1.75 D, the more myopic eye was more likely to be the dominant sighting eye than for lower levels of anisometropia (p=0.002). Subjects with greater levels of anisometropia (> 1.75 D) also showed high levels of correlation between the dominant and non-dominant eyes in their biometric, biomechanical and optical characteristics. Conclusions: Although significantly different in axial length, anisometropic eyes display a high degree of interocular symmetry for a range of anterior eye biometrics and optical parameters. For higher levels of anisometropia, the more myopic eye tends to be the dominant sighting eye.

Philosophy, behaviour disorders, and the school

The recent exponential rise in the number of behaviour disorders has been the focus of a wide range of commentaries, ranging from the pedagogic and the administrative, to the sociological, and even the legal. This book will be the first to apply, in a systematic and thorough manner, the ideas of the foundational discipline of philosophy. A number of philosophical tools are applied here, tools arising through the medium of the traditional philosophical debates, such as those concerning governance, truth, logic, ethics, free-will, law and language. Each forms a separate chapter, but together they constitute a comprehensive, rigorous and original insight into what is now an important set of concerns for all those interested in the governance of children. The intention is threefold: first, to demonstrate the utility, accessibility and effectiveness of philosophical ideas within this important academic area. Philosophy does not have to be regarded an arcane and esoteric discipline, with only limited contemporary application, far from it. Second, the book offers a new set of approaches and ideas for both researchers and practitioners within education, a field is in danger of continually using the same ideas, to endlessly repeat the same conclusions. Third, the book offers a viable alternative to the dominant psychological model which increasingly employs pathology as its central rationale for conduct. The book would not only be of interest to mainstream educators, and to those students and academics interested in philosophy, and more specifically, the application of philosophical ideas to educational issues, it would also be an appropriate text for courses on education and difference, and due to the breadth of the philosophical issues addressed, courses on applied philosophy.

Mapping resilience : A framework for changing cities

Urban centres base their resilience on the ability to evolve and adapt as needed throughout their life. Although constantly developing, changing and subsuming nature for its needs, the current age of environmental awareness requires that cities progress in a more conscious and considered way. While they have become the dominant form of human habitation, there now exists a need to integrate 'green' solutions into urban centres to address social, physical and environmental wellbeing. The means of implementing the vast array of possible solutions without negative impacts is not clear; cities are complex systems, layering meaning, history and cultural memory ‐ they are a manifestation of shared cultural values, and as such, they do not allow a tabula rasa approach of 'blanket' solutions. All around us, cities are continuing to develop and change, and although their form is varied ‐ sprawling cities with density and sustainability problems; or collapsing cities with 'dead' centres and dilapidated districts – a common issue is the resilience of the local identity. The strength or resilience of cities lies in the elements which have become fixed points in the urban structure, giving character and identity to a shared urban experience. These elements need to be identified and either maintained or revitalised. Similarly, the identification of urban elements which can most viably be modified without compromising character and identity of place, will assist in making concrete contributions to increasing both the sustainability and experience of cities, making them more resilient. Through an examination of case studies, this paper suggests a framework to inform urban renewal assessing the widespread elements which generate an urban identity, beyond the traditional approach of heritage conservation for cultural or tourist purposes. The rapid contemporary alteration of urban structures requires an innovative methodology which satisfies on one side the need of new sustainable performances and, on the other, the resilience of the local character.

The collaborative push : pushing beyond rhetoric and gaining evidence

Collaboration has been enacted as a core strategy by both the government and nongovernment sectors to address many of the intractable issues confronting contemporary society. The cult of collaboration has become so pervasive that it is now an elastic term referring generally to any form of ‘working together’. The lack of specificity about collaboration and its practice means that it risks being reduced to mere rhetoric without sustained practice or action. Drawing on an extensive data set (qualitative, quantitative) of broadly collaborative endeavours gathered over ten years in Queensland, Australia, this paper aims to fill out the black box of collaboration. Specifically it examines the drivers for collaboration, dominant structures and mechanisms adopted, what has worked and unintended consequences. In particular it investigates the skills and competencies required in an embeded collaborative endeavour within and across organisations. Social network analysis is applied to isolate the structural properties of collaborations over other forms of integration as well as highlighting key roles and tasks. Collaboration is found to be a distinctive form of working together, characterised by intense and interdependent relationships and exchanges, higher levels of cohesion (density) and requiring new ways of behaving, working, managing and leading. These elements are configured into a practice framework. Developing an empirical evidence base for collaboration structure, practice and strategy provides a useful foundation for theory extension. The paper concludes that for collaboration, to be successfully employed as a management strategy it must move beyond rhetoric and develop a coherent model for action.