The effect of flocculants, shear, vacuum and depithing on the formation of thin bagasse pulp pads

The effect of bentonite micro-particles and cationic polyacrylamide (CPAM) on the filtration properties of bagasse pulp was investigated under shearing conditions. CPAM improves retention but the bentonite addition level must be optimised for further improvements in retention. A Dynamic Drainage Jar (‘Britt Jar’) was modified to allow bagasse pulp slurry to be subjected to vacuum allowing a thin pulp pad to be formed. Bagasse pulp which had had the majority of the fine fibre removed prior to pulping drained more quickly than a conventional bagasse pulp when vacuum was not applied, however this situation was reversed when vacuum was used. The flocculants continue to improve fibre retention under vacuum and shear conditions but with reduced effectiveness.

Alkaline hydrothermal treatment of titanate nanostructures

Since its initial proposal in 1998, alkaline hydrothermal processing has rapidly become an established technology for the production of titanate nanostructures. This simple, highly reproducible process has gained a strong research following since its conception. However, complete understanding and elucidation of nanostructure phase and formation have not yet been achieved. Without fully understanding phase, formation, and other important competing effects of the synthesis parameters on the final structure, the maximum potential of these nanostructures cannot be obtained. Therefore this study examined the influence of synthesis parameters on the formation of titanate nanostructures produced by alkaline hydrothermal treatment. The parameters included alkaline concentration, hydrothermal temperature, the precursor material‘s crystallite size and also the phase of the titanium dioxide precursor (TiO2, or titania). The nanostructure‘s phase and morphology was analysed using X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy. X-ray photoelectron spectroscopy (XPS), dynamic light scattering (non-invasive backscattering), nitrogen sorption, and Rietveld analysis were used to determine phase, for particle sizing, surface area determinations, and establishing phase concentrations, respectively. This project rigorously examined the effect of alkaline concentration and hydrothermal temperature on three commercially sourced and two self-prepared TiO2 powders. These precursors consisted of both pure- or mixed-phase anatase and rutile polymorphs, and were selected to cover a range of phase concentrations and crystallite sizes. Typically, these precursors were treated with 5–10 M sodium hydroxide (NaOH) solutions at temperatures between 100–220 °C. Both nanotube and nanoribbon morphologies could be produced depending on the combination of these hydrothermal conditions. Both titania and titanate phases are comprised of TiO6 units which are assembled in different combinations. The arrangement of these atoms affects the binding energy between the Ti–O bonds. Raman spectroscopy and XPS were therefore employed in a preliminary study of phase determination for these materials. The change in binding energy from a titania to a titanate binding energy was investigated in this study, and the transformation of titania precursor into nanotubes and titanate nanoribbons was directly observed by these methods. Evaluation of the Raman and XPS results indicated a strengthening in the binding energies of both the Ti (2p3/2) and O (1s) bands which correlated to an increase in strength and decrease in resolution of the characteristic nanotube doublet observed between 320 and 220 cm.1 in the Raman spectra of these products. The effect of phase and crystallite size on nanotube formation was examined over a series of temperatures (100.200 �‹C in 20 �‹C increments) at a set alkaline concentration (7.5 M NaOH). These parameters were investigated by employing both pure- and mixed- phase precursors of anatase and rutile. This study indicated that both the crystallite size and phase affect nanotube formation, with rutile requiring a greater driving force (essentially �\harsher. hydrothermal conditions) than anatase to form nanotubes, where larger crystallites forms of the precursor also appeared to impede nanotube formation slightly. These parameters were further examined in later studies. The influence of alkaline concentration and hydrothermal temperature were systematically examined for the transformation of Degussa P25 into nanotubes and nanoribbons, and exact conditions for nanostructure synthesis were determined. Correlation of these data sets resulted in the construction of a morphological phase diagram, which is an effective reference for nanostructure formation. This morphological phase diagram effectively provides a .recipe book�e for the formation of titanate nanostructures. Morphological phase diagrams were also constructed for larger, near phase-pure anatase and rutile precursors, to further investigate the influence of hydrothermal reaction parameters on the formation of titanate nanotubes and nanoribbons. The effects of alkaline concentration, hydrothermal temperature, crystallite phase and size are observed when the three morphological phase diagrams are compared. Through the analysis of these results it was determined that alkaline concentration and hydrothermal temperature affect nanotube and nanoribbon formation independently through a complex relationship, where nanotubes are primarily affected by temperature, whilst nanoribbons are strongly influenced by alkaline concentration. Crystallite size and phase also affected the nanostructure formation. Smaller precursor crystallites formed nanostructures at reduced hydrothermal temperature, and rutile displayed a slower rate of precursor consumption compared to anatase, with incomplete conversion observed for most hydrothermal conditions. The incomplete conversion of rutile into nanotubes was examined in detail in the final study. This study selectively examined the kinetics of precursor dissolution in order to understand why rutile incompletely converted. This was achieved by selecting a single hydrothermal condition (9 M NaOH, 160 °C) where nanotubes are known to form from both anatase and rutile, where the synthesis was quenched after 2, 4, 8, 16 and 32 hours. The influence of precursor phase on nanostructure formation was explicitly determined to be due to different dissolution kinetics; where anatase exhibited zero-order dissolution and rutile second-order. This difference in kinetic order cannot be simply explained by the variation in crystallite size, as the inherent surface areas of the two precursors were determined to have first-order relationships with time. Therefore, the crystallite size (and inherent surface area) does not affect the overall kinetic order of dissolution; rather, it determines the rate of reaction. Finally, nanostructure formation was found to be controlled by the availability of dissolved titanium (Ti4+) species in solution, which is mediated by the dissolution kinetics of the precursor.

Developing managers as researchers using a learning cohort approach

This paper describes the design process and curriculum for a learning cohort of eight managers who came from public and private providers of vocational education and training. While the authors found no discussion on developing research knowledge and skills of managers using learning cohorts, the general learning cohorts literature provided a number of recommendations for learning cohort design. The initial stages of the learning cohort were evaluated. The results highlighted the importance of clarifying the psychological contract and its use in self-selection, supported the recommendations in the literature of the significance of the careful design and implementation of an initial residential workshop and also found support for further residential workshops of a similar design. The attendance of the cohort members in tow faculty wide core research units drew mixed comments.

The formation of, and change in, the psychological contracts of graduates entering the Queensland public sector

The workplace is evolving and the predicted impact of demographic changes (Salt, 2009; Taylor, 2005) has seen organisations focus on strategic workforce planning. As part of this, many organisations have established or expanded formalised graduate programs to attract graduates and transition them effectively into organisations (McDermott, Mangan, & O'Connor, 2005; Terjesen, Freeman, & Vinnicombe, 2007). The workplace context is also argued to be changing because of the divergence in preferences and priorities across the different generations in the workplace - a topic which is prolific in the popular culture media but is yet to be fully developed in the academic literature (Jorgenson, 2003). The public sector recruits large numbers of graduates and maintains well established graduate programs. Like the workplace context, the public sector is seen to be undergoing a transition to more closely align its practices and processes with that of the private sector (Haynes & Melville Jones, 1999; N. Preston, 1995). Consequently, questions have been raised as to how new workforce entrants see the public sector and its associated attractiveness as an employment option. This research draws together these issues and reviews the formation of, and change in, the psychological contracts of graduates across ten Queensland public sector graduate programs. To understand the employment relationship, the theories of psychological contract and public service motivation are utilised. Specifically, this research focuses on graduates' and managers' expectations over time, the organisational perspective of the employment relationship and how ideology influences graduates' psychological contract. A longitudinal mixed method design, involving individual interviews and surveys, is employed along with significant researcher-practitioner collaboration throughout the research process. A number of important qualitative and quantitative findings arose from this study and there was strong triangulation between results from the two methods. Prior to starting with the organisation, graduates found it difficult to articulate their expectations; however, organisational experience rapidly brought these to the fore. Of the expectations that became salient, most centred on their relationship with their supervisor. Without experience and quality information on which to base their expectations, graduates tended to over-rely on sectoral stereotypes which negatively impacted their psychological contracts. Socialisation only limited affected graduates' psychological contracts and public service motivation. The graduate survey, measured thrice throughout the first 12 months of the graduate program, revealed that the psychological contract and public service motivation results followed a similar trajectory of beginning at mediocre levels, declining between times one and two and increasing between times two and three (although this is not back to original levels). Graduates attributed these to a number of sectoral, organisational, team, supervisory and individual factors. On a theoretical level, this research provides support for the notion of ideology within the psychological contract although it raises some important questions about how it is conceptualised. Additionally, support is given for the manager to be seen as the primary organisational counterpart to the employee in future theoretical and practical work. The research also argues to extend current notions of time within the psychological contract as this seems to be the most divergent and combustible issue across the generations in terms of how the workplace is perceived. A number of practical implications also transpire from the study and the collaborative foundation was highly successful. It is anticipated that this research will make a meaningful contribution to both the theory and practice of the employment relationship with particular regard to graduates entering the public sector.

Effect of group formation on performance, task management and social loafing

Engineering graduates of today are required to adapt to a rapidly changing work environment. In particular, they are expected to demonstrate enhanced capabilities in both mono-disciplinary and multi-disciplinary teamwork environments. Engineering education needs, as a result, to further focus on developing group work capabilities amongst engineering graduates. Over the last two years, the authors trialed various group work strategies across two engineering disciplines. In particular, the effect of group formation on students' performance, task management, and social loafing was analyzed. A recently developed online teamwork management tool, Teamworker, was used to collect students' experience of the group work. Analysis showed that students who were allowed to freely allocate to any group were less likely to report loafing from other team members, than students who were pre-allocated to a group. It also showed that performance was more affected by the presence or absence of a leader in pre-allocated rather than free-allocated groups.

Interest from Tertiary Educated Persons in Fostering Children with Higher Care needs under a Professional (Paid) Model Compared with General Foster Care

The number of Australian children requiring foster care due to abuse and neglect is increasing at a faster rate than suitable carers can be recruited. Currently increased numbers of foster children are presenting with higher care needs. Evidence suggests carers with a higher education could contribute to placement stability and ultimately provide more positive outcomes for this group of children. This paper explores the level of interest by tertiary educated persons toward a model of fostering for children with higher needs. Using a descriptive survey methodology, a convenience sample of 644 university undergraduate and postgraduate students within faculties of health sciences, and education, arts and social sciences was employed. Psychology students in the 17-26 year old age group showed greatest interest in a professional foster care model and this was statistically significant (p=0.002 955 CI .000-.010) when compared to other health professionals and other age groups. Education students held the highest interest in general fostering although not statistically significant. When these survey results were extrapolated to the total number of health professionals in Australia there could be 8,385 potential recruits for a model professional foster care. Focused campaigns are required to source professional as recruits to fostering with the benefit of servicing the placement needs of higher care needs children and contributing to general foster care resources.

An evidence-based approach to professional development planning in large state educational systems

This paper presents a systems-level approach for adjudicating the prioritization, selection, and planning of inservcie professional development (PD) for teachers. We present a step-by-step model for documenting and assessing system-wide 'bids' for professional development programs

Theoretical analysis of serrated chip formation based on ideal models in high speed cutting

In this paper, two ideal formation models of serrated chips, the symmetric formation model and the unilateral right-angle formation model, have been established for the first time. Based on the ideal models and related adiabatic shear theory of serrated chip formation, the theoretical relationship among average tooth pitch, average tooth height and chip thickness are obtained. Further, the theoretical relation of the passivation coefficient of chip's sawtooth and the chip thickness compression ratio is deduced as well. The comparison between these theoretical prediction curves and experimental data shows good agreement, which well validates the robustness of the ideal chip formation models and the correctness of the theoretical deducing analysis. The proposed ideal models may have provided a simple but effective theoretical basis for succeeding research on serrated chip morphology. Finally, the influences of most principal cutting factors on serrated chip formation are discussed on the basis of a series of finite element simulation results for practical advices of controlling serrated chips in engineering application.

Deterring drug drivers : a study into the initial impact of oral random roadside drug testing in Queensland

Objective: The global implementation of oral random roadside drug testing is relatively limited, and correspondingly, the literature that focuses on the effectiveness of this intervention is scant. This study aims to provide a preliminary indication of the impact of roadside drug testing in Queensland. Methods: A sample of Queensland motorists’ (N= 922) completed a self-report questionnaire to investigate their drug driving behaviour, as well as examine the perceived affect of legal sanctions (certainty, severity and swiftness) and knowledge of the countermeasure on their subsequent offending behaviour. Results: Analysis of the collected data revealed that approximately 20% of participants reported drug driving at least once in the last six months. Overall, there was considerable variability in respondent’s perceptions regarding the certainty, severity and swiftness of legal sanctions associated with the testing regime and a considerable proportion remained unaware of testing practices. In regards to predicting those who intended to drug driving again in the future, perceptions of apprehension certainty, more specifically low certainty of apprehension, were significantly associated with self-reported intentions to offend. Additionally, self-reported recent drug driving activity and frequent drug consumption were also identified as significant predictors, which indicates that in the current context, past behaviour is a prominent predictor of future behaviour. To a lesser extent, awareness of testing practices was a significant predictor of intending not to drug drive in the future. Conclusion: The results indicate that drug driving is relatively prevalent on Queensland roads, and a number of factors may influence such behaviour. Additionally, while the roadside testing initiative is beginning to have a deterrent impact, its success will likely be linked with targeted intelligence-led implementation in order to increase apprehension levels as well as the general deterrent effect.

If Big Brother comes to a venue near you! Employee surveillance issues and the communication professional

Todoy's monogers-drowing on the expertise of their IT professiono/s-professionals need to address to forestall future problems. lA questionnaire is included as a starting point for communication professionals to assess their own attitudes and values to workplace surveillance.

A navigating rat animat

This paper presents a new rat animat, a rat-sized bio-inspired robot platform currently being developed for embodied cognition and neuroscience research. The rodent animat is 150mm x 80mm x 70mm and has a different drive, visual, proximity, and odometry sensors, x86 PC, and LCD interface. The rat animat has a bio-inspired rodent navigation and mapping system called RatSLAM which demonstrates the capabilities of the platform and framework. A case study is presented of the robot's ability to learn the spatial layout of a figure of eight laboratory environment, including its ability to close physical loops based on visual input and odometry. A firing field plot similar to rodent 'non-conjunctive grid cells' is shown by plotting the activity of an internal network. Having a rodent animat the size of a real rat allows exploration of embodiment issues such as how the robot's sensori-motor systems and cognitive abilities interact. The initial observations concern the limitations of the deisgn as well as its strengths. For example, the visual sensor has a narrower field of view and is located much closer to the ground than for other robots in the lab, which alters the salience of visual cues and the effectiveness of different visual filtering techniques. The small size of the robot relative to corridors and open areas impacts on the possible trajectories of the robot. These perspective and size issues affect the formation and use of the cognitive map, and hence the navigation abilities of the rat animat.

Towards a relational contracting framework in the Australian construction industry : an initial framework

The Australian construction industry is characterized as being a competitive and risky business environment due to lack of cooperation, insufficient trust, ineffective communication and adversarial relationships which are likely lead to poor project performance. Relational contracting (RC) is advocated by literature as an innovative approach to improve the procurement process in the construction industry. Various studies have collectively added to the current knowledge of known RC norms, but there seem to be little effort on investigating the determinants of RC and its impact on project outcomes. In such circumstances, there is lack of evidence and explanation on the manner on how these issues lead to different performance. Simultaneously, the New Engineering Contract (NEC) that embraced the concept of RC is seen as a modern way of contracting and also considered as one of the best approaches to the perennial problem of improving adversarial relationships within the industry. The reality of practice of RC in Australia is investigated through the lens of the NEC. A synthesis of literature views on the concept, processes and tools of RC is first conducted to develop the framework of RC. A case study approach is proposed for an in-depth analysis to explore the critical issues addressed by RC in relation to project performance. Understanding the realities of RC will assist stakeholders in the construction industry with their investment in RC.

The impact of sulphur content of diesel fuel on ultrafine particle formation

Early this year the Australian Department of Environment and Heritage commissioned a desktop literature review with a focus on ultrafine particles including analysis of health impacts of the particles as well as the impact of sulphur content of diesel fuel on ultrafine particle emission. This paper summarizes the findings of the report on the link between the sulphur content of diesel fuels and the number of ultrafine particles in diesel emissions. The literature search on this topic resulted in over 150 publications. The majority of these publications, although investigating different aspects of the influence of fuel sulphur level on diesel vehicle emissions, were not directly concerned with ultrafine particle emissions. A specific focus of the paper is on: ----- ----- summary of state of knowledge established by the review, and ----- ----- summary of recommendations on the research priorities for Australia to address the information gaps for this issue, and on the appropriate management responses.

Student engagement with an ePortfolio : a case study of pre-service education students

The emergence of ePortfolios is relatively recent in the university sector as a way to engage students in their learning and assessment, and to produce records of their accomplishments. An ePortfolio is an online tool that students can utilise to record, catalogue, retrieve and present reflections and artefacts that support and demonstrate the development of graduate students’ capabilities and professional standards across university courses. The ePortfolio is therefore considered as both process and product. Although ePortfolios show promise as a useful tool and their uptake has grown, they are not yet a mainstream higher education technology. To date, the emphasis has been on investigating their potential to support the multiple purposes of learning, assessment and employability, but less is known about whether and how students engage with ePortfolios in the university setting. This thesis investigates student engagement with an ePortfolio in one university. As the educational designer for the ePortfolio project at the University, I was uniquely positioned as a researching professional to undertake an inquiry into whether students were engaging with the ePortfolio. The participants in this study were a cohort (defined by enrolment in a unit of study) of second and third year education students (n=105) enrolled in a four year Bachelor of Education degree. The students were introduced to the ePortfolio in an introductory lecture and a hands-on workshop in a computer laboratory. They were subsequently required to complete a compulsory assessment task – a critical reflection - using the ePortfolio. Following that, engagement with the ePortfolio was voluntary. A single case study approach arising from an interpretivist paradigm directed the methodological approach and research design for this study. The study investigated the participants’ own accounts of their experiences with the ePortfolio, including how and when they engaged with the ePortfolio and the factors that impacted on their engagement. Data collection methods consisted of an attitude survey, student interviews, document collection, a researcher reflective journal and researcher observations. The findings of the study show that, while the students were encouraged to use the ePortfolio as a learning and employability tool, most students ultimately chose to disengage after completing the assessment task. Only six of the forty-five students (13%) who completed the research survey had used the ePortfolio in a sustained manner. The data obtained from the students during this research has provided insight into reasons why they disengaged from the ePortfolio. The findings add to the understandings and descriptions of student engagement with technology, and more broadly, advance the understanding of ePortfolios. These findings also contribute to the interdisciplinary field of technology implementation. There are three key outcomes from this study, a model of student engagement with technology, a set of criteria for the design of an ePortfolio, and a set of recommendations for effective practice for those implementing ePortfolios. The first, the Model of Student Engagement with Technology (MSET) (Version 2) explored student engagement with technology by highlighting key engagement decision points for students The model was initially conceptualised by building on work of previous research (Version 1), however, following data analysis a new model emerged, MSET (Version 2). The engagement decision points were identified as: • Prior Knowledge and Experience, leading to imagined usefulness and imagined ease of use; • Initial Supported Engagement, leading to supported experience of usefulness and supported ease of use; • Initial Independent Engagement, leading to actual experience of independent usefulness and actual ease of use; and • Ongoing Independent Engagement, leading to ongoing experience of usefulness and ongoing ease of use. The Model of Student Engagement with Technology (MSET) goes beyond numerical figures of usage to demonstrate student engagement with an ePortfolio. The explanatory power of the model is based on the identification of the types of decisions that students make and when they make them during the engagement process. This model presents a greater depth of understanding student engagement than was previously available and has implications for the direction and timing of future implementation, and academic and student development activities. The second key outcome from this study is a set of criteria for the re-conceptualisation of the University ePortfolio. The knowledge gained from this research has resulted in a new set of design criteria that focus on the student actions of writing reflections and adding artefacts. The process of using the ePortfolio is reconceptualised in terms of privileging student learning over administrative compliance. The focus of the ePortfolio is that the writing of critical reflections is the key function, not the selection of capabilities. The third key outcome from this research consists of five recommendations for university practice that have arisen from this study. They are that, sustainable implementation is more often achieved through small steps building on one another; that a clear definition of the purpose of an ePortfolio is crucial for students and staff; that ePortfolio pedagogy should be the driving force not the technology; that the merit of the ePortfolio is fostered in students and staff; and finally, that supporting delayed task performance is crucial. Students do not adopt an ePortfolio just because it is provided. While students must accept responsibility for their own engagement with the ePortfolio, the institution has to accept responsibility for providing the environment, and technical and pedagogical support to foster engagement. Ultimately, an ePortfolio should be considered as a joint venture between student and institution where strong returns on investment can be realised by both. It is acknowledged that the current implementation strategies for the ePortfolio are just the beginning of a much longer process. The real rewards for students, academics and the university lie in the future.

Formation of one-dimensional capped ZnO nanoparticle assemblies at the air/water interface

The self-assembling behavior and microscopic structure of zinc oxide nanoparticle Langmuir-Blodgett monolayer films were investigated for the case of zinc oxide nanoparticles coated with a hydrophobic layer of dodecanethiol. Evolution of nanoparticle film structure as a function of surface pressure (π) at the air-water interface was monitored in situ using Brewster’s angle microscopy, where it was determined that π=16 mN/m produced near-defect-free monolayer films. Transmission electron micrographs of drop-cast and Langmuir-Schaefer deposited films of the dodecanethiol-coated zinc oxide nanoparticles revealed that the nanoparticle preparation method yielded a microscopic structure that consisted of one-dimensional rodlike assemblies of nanoparticles with typical dimensions of 25 x 400 nm, encased in the organic dodecanethiol layer. These nanoparticle-containing rodlike micelles were aligned into ordered arrangements of parallel rods using the Langmuir-Blodgett technique.