Key derivation function : the SCKDF scheme

A key derivation function is used to generate one or more cryptographic keys from a private (secret) input value. This paper proposes a new method for constructing a generic stream cipher based key derivation function. We show that our proposed key derivation function based on stream ciphers is secure if the underlying stream cipher is secure. We simulate instances of this stream cipher based key derivation function using three eStream finalist: Trivium, Sosemanuk and Rabbit. The simulation results show these stream cipher based key derivation functions offer efficiency advantages over the more commonly used key derivation functions based on block ciphers and hash functions.

Cascaded DC-DC converter connection of photovoltaic modules

New residential scale photovoltaic (PV) arrays are commonly connected to the grid by a single dc-ac inverter connected to a series string of pv panels, or many small dc-ac inverters which connect one or two panels directly to the ac grid. This paper proposes an alternative topology of nonisolated per-panel dc-dc converters connected in series to create a high voltage string connected to a simplified dc-ac inverter. This offers the advantages of a "converter-per-panel" approach without the cost or efficiency penalties of individual dc-ac grid connected inverters. Buck, boost, buck-boost, and Cu´k converters are considered as possible dc-dc converters that can be cascaded. Matlab simulations are used to compare the efficiency of each topology as well as evaluating the benefits of increasing cost and complexity. The buck and then boost converters are shown to be the most efficient topologies for a given cost, with the buck best suited for long strings and the boost for short strings. While flexible in voltage ranges, buck-boost, and Cu´k converters are always at an efficiency or alternatively cost disadvantage.

A class B switch-mode assisted linear amplifier

A switch-mode assisted linear amplifier (SMALA) combining a linear (Class B) and a switch-mode (Class D) amplifier is presented. The usual single hysteretic controlled half-bridge current dumping stage is replaced by two parallel buck converter stages, in a parallel voltage controlled topology. These operate independently: one buck converter sources current to assist the upper Class B output device, and a complementary converter sinks current to assist the lower device. This topology lends itself to a novel control approach of a dead-band at low power levels where neither class D amplifier assists, allowing the class B amplifier to supply the load without interference, ensuring high fidelity. A 20 W implementation demonstrates 85% efficiency, with distortion below 0.08% measured across the full audio bandwidth at 15 W. The class D amplifier begins assisting at 2 W, and below this value, the distortion was below 0.03%. Complete circuitry is given, showing the simplicity of the additional class D amplifier and its corresponding control circuitry.

The health information practices of people living with chronic health conditions: Implications for health literacy

The reduction of the health literacy concept to a functional relationship with text, does not acknowledge the range of information sources that people draw from in order to make informed decision about their health and treatment. Drawing from two studies that explored how people with two different but complex and life-threatening chronic health conditions, chronic kidney disease and HIV, a socio-cultural understanding of the practise of health literacy is described. Health information is experienced by patients as a chronic health condition landscape, and develops from three information sources; namely epistemic, social and corporeal sources. Participants in both studies used activities that involved orienting, sharing and creating information to map this landscape which was used to inform their decision-making. These findings challenge the traditional conceptions of health literacy and suggest an approach that views the landscape of chronic illness as being socially, physically and contextually constructed. This approach necessitates a recasting of health literacy away from a sole interest in skills and towards understanding how information practices facilitate people becoming health literate.

PV string per-module maximum power point enabling converters

Many grid connected PV installations consist of a single series string of PV modules and a single DC-AC inverter. This efficiency of this topology can be enhanced with additional low power, low cost per panel converter modules. Most current flows directly in the series string which ensures high efficiency. However parallel Cúk or buck-boost DC-DC converters connected across each adjacent pair of modules now support any desired current difference between series connected PV modules. Each converter “shuffles” the desired difference in PV module currents between two modules and so on up the string. Spice simulations show that even with poor efficiency, these modules can make a significant improvement to the overall power which can be recovered from partially shaded PV strings.

Cascaded DC-DC converter connection of photovoltaic modules

New residential scale photovoltaic (PV) arrays are commonly connected to the grid by a single DC-AC inverter connected to a series string of PV modules, or many small DC-AC inverters which connect one or two modules directly to the AC grid. This paper shows that a "converter-per-module" approach offers many advantages including individual module maximum power point tracking, which gives great flexibility in module layout, replacement, and insensitivity to shading; better protection of PV sources, and redundancy in the case of source or converter failure; easier and safer installation and maintenance; and better data gathering. Simple nonisolated per-module DC-DC converters can be series connected to create a high voltage string connected to a simplified DC-AC inverter. These advantages are available without the cost or efficiency penalties of individual DC-AC grid connected inverters. Buck, boost, buck-boost and Cuk converters are possible cascadable converters. The boost converter is best if a significant step up is required, such as with a short string of 12 PV modules. A string of buck converters requires many more modules, but can always deliver any combination of module power. The buck converter is the most efficient topology for a given cost. While flexible in voltage ranges, buck-boost and Cuk converters are always at an efficiency or alternatively cost disadvantage

Evaluating MPPT converter topologies using a Matlab PV model

An accurate PV module electrical model is presented based on the Shockley diode equation. The simple model has a photo-current current source, a single diode junction and a series resistance, and includes temperature dependences. The method of parameter extraction and model evaluation in Matlab is demonstrated for a typical 60W solar panel. This model is used to investigate the variation of maximum power point with temperature and isolation levels. A comparison of buck versus boost maximum power point tracker (MPPT) topologies is made, and compared with a direct connection to a constant voltage (battery) load. The boost converter is shown to have a slight advantage over the buck, since it can always track the maximum power point.

Evaluating MPPT converter topologies using a MATLAB PV model

An accurate PV module electrical model is presented based on the Shockley diode equation. The simple model has a photo-current current source, a single diode junction and a series resistance, and includes temperature dependences. The method of parameter extraction and model evaluation in Matlab is demonstrated for a typical 60W solar panel. This model is used to investigate the variation of maximumpower point with temperature and insolation levels. A comparison of buck versus boostmaximum power point tracker (MPPT) topologies is made, and compared with a direct connection to a constant voltage (battery) load. The boost converter is shown to have a slight advantage over the buck, since it can always track the maximum power point.

Weak key-IV pairs in the A5/1 stream cipher

A5/1 is a shift register based stream cipher which provides privacy for the GSM system. In this paper, we analyse the loading of the secret key and IV during the initialisation process of A5/1. We demonstrate the existence of weak key-IV pairs in the A5/1 cipher due to this loading process; these weak key-IV pairs may generate one, two or three registers containing all-zero values, which may lead in turn to weak keystream sequences. In the case where two or three registers contain only zeros, we describe a distinguisher which leads to a complete decryption of the affected messages.

Development and formative evaluation of a motorcycle rider training intervention to address risk taking

The need to address on-road motorcycle safety in Australia is important due to the disproportionately high percentage of riders and pillions killed and injured each year. One approach to preventing motorcycle-related injury is through training and education. However, motorcycle rider training lacks empirical support as an effective road safety countermeasure to reduce crash involvement. Previous reviews have highlighted that risk-taking is a contributing factor in many motorcycle crashes, rather than merely a lack of vehicle-control skills (Haworth & Mulvihill, 2005; Jonah, Dawson & Bragg, 1982; Watson et al, 1996). Hence, though the basic vehicle-handling skills and knowledge of road rules that are taught in most traditional motorcycle licence training programs may be seen as an essential condition of safe riding, they do not appear to be sufficient in terms of crash reduction. With this in mind there is considerable scope for the improvement of program focus and content for rider training and education. This program of research examined an existing traditional pre-licence motorcycle rider training program and formatively evaluated the addition of a new classroom-based module to address risky riding; the Three Steps to Safer Riding program. The pilot program was delivered in the real world context of the Q-Ride motorcycle licensing system in the state of Queensland, Australia. Three studies were conducted as part of the program of research: Study 1, a qualitative investigation of delivery practices and student learning needs in an existing rider training course; Study 2, an investigation of the extent to which an existing motorcycle rider training course addressed risky riding attitudes and motives; and Study 3, a formative evaluation of the new program. A literature review as well as the investigation of learning needs for motorcyclists in Study 1 aimed to inform the initial planning and development of the Three Steps to Safer Riding program. Findings from Study 1 suggested that the training delivery protocols used by the industry partner training organisation were consistent with a learner-centred approach and largely met the learning needs of trainee riders. However, it also found that information from the course needs to be reinforced by on-road experiences for some riders once licensed and that personal meaning for training information was not fully gained until some riding experience had been obtained. While this research informed the planning and development of the new program, a project team of academics and industry experts were responsible for the formulation of the final program. Study 2 and Study 3 were conducted for the purpose of formative evaluation and program refinement. Study 2 served primarily as a trial to test research protocols and data collection methods with the industry partner organisation and, importantly, also served to gather comparison data for the pilot program which was implemented with the same rider training organisation. Findings from Study 2 suggested that the existing training program of the partner organisation generally had a positive (albeit small) effect on safety in terms of influencing attitudes to risk taking, the propensity for thrill seeking, and intentions to engage in future risky riding. However, maintenance of these effects over time and the effects on riding behaviour remain unclear due to a low response rate upon follow-up 24 months after licensing. Study 3 was a formative evaluation of the new pilot program to establish program effects and possible areas for improvement. Study 3a examined the short term effects of the intervention pilot on psychosocial factors underpinning risky riding compared to the effects of the standard traditional training program (examined in Study 2). It showed that the course which included the Three Steps to Safer Riding program elicited significantly greater positive attitude change towards road safety than the existing standard licensing course. This effect was found immediately following training, and mean scores for attitudes towards safety were also maintained at the 12 month follow-up. The pilot program also had an immediate effect on other key variables such as risky riding intentions and the propensity for thrill seeking, although not significantly greater than the traditional standard training. A low response rate at the 12 month follow-up unfortunately prevented any firm conclusions being drawn regarding the impact of the pilot program on self-reported risky riding once licensed. Study 3a further showed that the use of intermediate outcomes such as self-reported attitudes and intentions for evaluation purposes provides insights into the mechanisms underpinning risky riding that can be changed by education and training. A multifaceted process evaluation conducted in Study 3b confirmed that the intervention pilot was largely delivered as designed, with course participants also rating most aspects of training delivery highly. The complete program of research contributed to the overall body of knowledge relating to motorcycle rider training, with some potential implications for policy in the area of motorcycle rider licensing. A key finding of the research was that psychosocial influences on risky riding can be shaped by structured education that focuses on awareness raising at a personal level and provides strategies to manage future riding situations. However, the formative evaluation was mainly designed to identify areas of improvement for the Three Steps to Safer Riding program and found several areas of potential refinement to improve future efficacy of the program. This included aspects of program content, program delivery, resource development, and measurement tools. The planned future follow-up of program participants' official crash and traffic offence records over time may lend further support for the application of the program within licensing systems. The findings reported in this thesis offer an initial indication that the Three Steps to Safer Riding is a useful resource to accompany skills-based training programs.

Indirect message injection for MAC generation

This paper presents a model for the generation of a MAC tag using a stream cipher. The input message is used indirectly to control segments of the keystream that form the MAC tag. Several recent proposals can be considered as instances of this general model, as they all perform message accumulation in this way. However, they use slightly different processes in the message preparation and finalisation phases. We examine the security of this model for different options and against different types of attack, and conclude that the indirect injection model can be used to generate MAC tags securely for certain combinations of options. Careful consideration is required at the design stage to avoid combinations of options that result in susceptibility to forgery attacks. Additionally, some implementations may be vulnerable to side-channel attacks if used in Authenticated Encryption (AE) algorithms. We give design recommendations to provide resistance to these attacks for proposals following this model.

Algebraic analysis of Trivium-like ciphers

Trivium is a bit-based stream cipher in the final portfolio of the eSTREAM project. In this paper, we apply the algebraic attack approach of Berbain et al. to Trivium-like ciphers and perform new analyses on them. We demonstrate a new algebraic attack on Bivium-A. This attack requires less time and memory than previous techniques to recover Bivium-A's initial state. Though our attacks on Bivium-B, Trivium and Trivium-N are worse than exhaustive keysearch, the systems of equations which are constructed are smaller and less complex compared to previous algebraic analyses. We also answer an open question posed by Berbain et al. on the feasibility of applying their technique on Trivium-like ciphers. Factors which can affect the complexity of our attack on Trivium-like ciphers are discussed in detail. Analysis of Bivium-B and Trivium-N are omitted from this manuscript. The full paper is available on the IACR ePrint Archive.

Design, implementation and multisite evaluation of a system suitability protocol for the quantitative assessment of instrument performance in liquid chromatography-multiple reaction monitoring-MS (LC-MRM-MS)

Multiple reaction monitoring (MRM) mass spectrometry coupled with stable isotope dilution (SID) and liquid chromatography (LC) is increasingly used in biological and clinical studies for precise and reproducible quantification of peptides and proteins in complex sample matrices. Robust LC-SID-MRM-MS-based assays that can be replicated across laboratories and ultimately in clinical laboratory settings require standardized protocols to demonstrate that the analysis platforms are performing adequately. We developed a system suitability protocol (SSP), which employs a predigested mixture of six proteins, to facilitate performance evaluation of LC-SID-MRM-MS instrument platforms, configured with nanoflow-LC systems interfaced to triple quadrupole mass spectrometers. The SSP was designed for use with low multiplex analyses as well as high multiplex approaches when software-driven scheduling of data acquisition is required. Performance was assessed by monitoring of a range of chromatographic and mass spectrometric metrics including peak width, chromatographic resolution, peak capacity, and the variability in peak area and analyte retention time (RT) stability. The SSP, which was evaluated in 11 laboratories on a total of 15 different instruments, enabled early diagnoses of LC and MS anomalies that indicated suboptimal LC-MRM-MS performance. The observed range in variation of each of the metrics scrutinized serves to define the criteria for optimized LC-SID-MRM-MS platforms for routine use, with pass/fail criteria for system suitability performance measures defined as peak area coefficient of variation <0.15, peak width coefficient of variation <0.15, standard deviation of RT <0.15 min (9 s), and the RT drift <0.5min (30 s). The deleterious effect of a marginally performing LC-SID-MRM-MS system on the limit of quantification (LOQ) in targeted quantitative assays illustrates the use and need for a SSP to establish robust and reliable system performance. Use of a SSP helps to ensure that analyte quantification measurements can be replicated with good precision within and across multiple laboratories and should facilitate more widespread use of MRM-MS technology by the basic biomedical and clinical laboratory research communities.

Characterisation of a human skin equivalent model to study the effects of ultraviolet B radiation on keratinocytes

The incidences of skin cancers resulting from chronic ultraviolet radiation (UVR) exposure are on the incline both in Australia and globally. Hence, the cellular and molecular pathways associated with UVR-induced photocarcinogenesis urgently need to be elucidated, in order to develop more robust preventative and treatment strategies against skin cancers. In vitro investigations into the effects of UVR (in particular the highly-mutagenic UVB wavelength) have, to date, mainly involved the use of cell culture and animal models. However, these models possess biological disparities to native skin, which to some extent have limited their relevance to the in vivo situation. To address this, we characterised a 3-dimensional, tissue-engineered human skin equivalent (HSE) model (consisting of primary human keratinocytes cultured on a dermal-derived scaffold) as a representation of a more physiologically-relevant platform to study keratinocyte responses to UVB. Significantly, we demonstrate that this model retains several important epidermal properties of native skin. Moreover, UVB-irradiation of the HSE constructs was shown to induce key markers of photodamage in the HSE keratinocytes, including the formation of cyclobutane pyrimidine dimers, the activation of apoptotic pathways, the accumulation of p53 and the secretion of inflammatory cytokines. Importantly, we also demonstrate that the UVB-exposed HSE constructs retain the capacity for epidermal repair and regeneration following photodamage. Together, our results demonstrate the potential of this skin equivalent model as a tool to study various aspects of the acute responses of human keratinocytes to UVB radiation damage.

Attracting and retaining specialist teachers and non-teaching professionals in Queensland secondary schools : a report to the Queensland Department of Education and Training

This report provides the Queensland Department of Education and Training (DET) with independent evidence based data to enable the identification of barriers and enablers to effective attraction and retention of suitably qualified people to specialist teaching and non‐teaching roles in Queensland secondary schools. The scope of this report is to consider the strategic imperatives, trends, and drivers as they apply to the recruitment and retention of specialised teachers and non‐teaching professionals. The research was specifically designed to inform DET on innovative and novel strategies to recruit and retain staff within Education Queensland in areas specifically identified as at risk of experiencing shortages in the near future. Those areas considered to be at risk of experiencing shortages included: • Teaching principals • Specialist teachers in mathematics, science, industrial technology and design, and special education • Non‐teaching professional roles, such as speech pathologists, occupational therapists, physiotherapists and registered nurses providing services in schools to students with special needs.