Particle and gaseous emissions from commercial aircraft at each stage of the landing and takeoff cycle

A novel technique was used to measure emission factors for commonly used commercial aircraft including a range of Boeing and Airbus airframes under real world conditions. Engine exhaust emission factors for particles in terms of particle number and mass (PM2.5), along with those for CO2, and NOx were measured for over 280 individual aircraft during the various modes of landing/takeoff (LTO) cycle. Results from this study show that particle number, and NOx emission factors are dependant on aircraft engine thrust level. Minimum and maximum emissions factors for particle number, PM2.5, and NOx emissions were found to be in the range of 4.16×1015-5.42×1016 kg-1, 0.03-0.72 g.kg-1, and 3.25-37.94 g.kg-1 respectively for all measured airframes and LTO cycle modes. Number size distributions of emitted particles for the naturally diluted aircraft plumes in each mode of LTO cycle showed that particles were predominantly in the range of 4 to 100 nm in diameter in all cases. In general, size distributions exhibit similar modality during all phases of the LTO cycle. A very distinct nucleation mode was observed in all particle size distributions, except for taxiing and landing of A320 aircraft. Accumulation modes were also observed in all particle size distributions. Analysis of aircraft engine emissions during LTO cycle showed that aircraft thrust level is considerably higher during taxiing than idling suggesting that International Civil Aviation Organization (ICAO) standards need to be modified as the thrust levels for taxi and idle are considered to be the same (7% of total thrust) [1].

Socioeconomic differences in takeaway food consumption and their contribution to inequalities in dietary intakes

Background Takeaway consumption has been increasing and may contribute to socioeconomic inequalities in overweight/obesity and chronic disease. This study examined socioeconomic differences in takeaway consumption patterns, and their contributions to dietary intake inequalities. Method Cross-sectional dietary intake data from adults aged between 25 and 64 years from the Australian National Nutrition Survey (n= 7319, 61% response rate). Twenty-four hour dietary recalls ascertained intakes of takeaway food, nutrients and fruit and vegetables. Education was used as socioeconomic indicator. Data were analysed using logistic regression and general linear models. Results Thirty-two percent (n = 2327) consumed takeaway foods in the 24 hour period. Lower-educated participants were less likely than their higher-educated counterparts to have consumed total takeaway foods (OR 0.64; 95% CI 0.52, 0.80). Of those consuming takeaway foods, the lowest-educated group was more likely to have consumed “less healthy” takeaway choices (OR 2.55; 95% CI 1.73, 3.77), and less likely to have consumed “healthy” choices (OR 0.52; 95% CI 0.36, 0.75). Takeaway foods made a greater contribution to energy, total fat, saturated fat, and fibre intakes among lower than higher-educated groups. Lower likelihood of fruit and vegetable intakes were observed among “less healthy” takeaway consumers, whereas a greater likelihood of their consumption was found among “healthy” takeaway consumers. Conclusions Total and the types of takeaway foods consumed may contribute to socioeconomic inequalities in intakes of energy, total and saturated fats. However, takeaway consumption is unlikely to be a factor contributing to the lower fruit and vegetable intakes among socioeconomically-disadvantaged groups.

Lift@Weimar : sustainable interaction with food, technology, and the city (Workshop)

This workshop explores innovative approaches to understanding and cultivating sustainable food culture in urban environments via human-computer-interaction (HCI) design and ubiquitous technologies. We perceive the city as an intersecting network of people, place, and technology in constant transformation. Our 2009 OZCHI workshop, Hungry 24/7? HCI Design for Sustainable Food Culture, opened a new space for discussion on this intersection amongst researchers and practitioners from diverse backgrounds including academia, government, industry, and non-for-profit organisations. Building on the past success, this new instalment of the workshop series takes a more refined view on mobile human-food interaction and the role of interactive media in engaging citizens to cultivate more sustainable everyday human-food interactions on the go. Interactive media in this sense is distributed, pervasive, and embedded in the city as a network. The workshop addresses environmental, health, and social domains of sustainability by bringing together insights across disciplines to discuss conceptual and design approaches in orchestrating mobility and interaction of people and food in the city as a network of people, place, technology, and food.

Household food expenditure and its contribution to socioeconomic inequalities in purchasing foods consistent with Australian dietary guideline recommendations

Aim: To examine the amount of money spent on food by household income, and to ascertain whether food expenditure mediates the relationship between household income and the purchase of staple foods consistent with Australian dietary guideline recommendations. ----- ----- Methods: In face-to-face interviews (n = 1003, 66.4% response rate), households in Brisbane, Australia were asked about their purchasing choices for a range of staple foods, including grocery items, fruits and vegetables. For each participant, information was obtained about their total weekly household food expenditure, along with their sociodemographic and household characteristics. ----- ----- Results: Household income was significantly associated with food expenditure; participants residing in higher-income households spent more money on food per household member than those from lower-income households. Lower income households were less likely to make food purchasing choices of dietary staples that were consistent with recommendations. However, food expenditure did not attenuate the relationship between household income and the purchase of staple foods consistent with dietary guideline recommendations. ----- ----- Conclusions: The findings suggest that food expenditure may not contribute to income inequalities in purchasing staple foods consistent with dietary guideline recommendations: instead, other material or psychosocial factors not considered in the current study may be more important determinants of these inequalities. Further research should examine whether expenditure on non-staple items and takeaway foods is a larger contributor to socioeconomic inequalities in dietary behavior.

What is food literacy and does it influence what we eat : a study of Australian food experts

This report details the findings of the Food Literacy Delphi Study. This study was the first of three studies commissioned by Health Promotion Queensland, Queensland Health. It examines the views of experts from around Australia about food literacy; its meaning, potential components and relationship to nutrition.

Development of a high-speed sensing and detection system for automatic removal of packages with leaky seals from a high-speed food processing and packaging line

Contamination of packaged foods due to micro-organisms entering through air leaks can cause serious public health issues and cost companies large amounts of money due to product recalls, consumer impact and subsequent loss of market share. The main source of contamination is leaks in packaging which allow air, moisture and microorganisms to enter the package. In the food processing and packaging industry worldwide, there is an increasing demand for cost effective state of the art inspection technologies that are capable of reliably detecting leaky seals and delivering products at six-sigma. The new technology will develop non-destructive testing technology using digital imaging and sensing combined with a differential vacuum technique to assess seal integrity of food packages on a high-speed production line. The cost of leaky packages in Australian food industries is estimated close to AUD $35 Million per year. Contamination of packaged foods due to micro-organisms entering through air leaks can cause serious public health issues and cost companies large sums of money due to product recalls, compensation claims and loss of market share. The main source of contamination is leaks in packaging which allow air, moisture and micro-organisms to enter the package. Flexible plastic packages are widely used, and are the least expensive form of retaining the quality of the product. These packets can be used to seal, and therefore maximise, the shelf life of both dry and moist products. The seals of food packages need to be airtight so that the food content is not contaminated due to contact with microorganisms that enter as a result of air leakage. Airtight seals also extend the shelf life of packaged foods, and manufacturers attempt to prevent food products with leaky seals being sold to consumers. There are many current NDT (non-destructive testing) methods of testing the seal of flexible packages best suited to random sampling, and for laboratory purposes. The three most commonly used methods are vacuum/pressure decay, bubble test, and helium leak detection. Although these methods can detect very fine leaks, they are limited by their high processing time and are not viable in a production line. Two nondestructive in-line packaging inspection machines are currently available and are discussed in the literature review. The detailed design and development of the High-Speed Sensing and Detection System (HSDS) is the fundamental requirement of this project and the future prototype and production unit. Successful laboratory testing was completed and a methodical design procedure was needed for a successful concept. The Mechanical tests confirmed the vacuum hypothesis and seal integrity with good consistent results. Electrically, the testing also provided solid results to enable the researcher to move the project forward with a certain amount of confidence. The laboratory design testing allowed the researcher to confirm theoretical assumptions before moving into the detailed design phase. Discussion on the development of the alternative concepts in both mechanical and electrical disciplines enables the researcher to make an informed decision. Each major mechanical and electrical component is detailed through the research and design process. The design procedure methodically works through the various major functions both from a mechanical and electrical perspective. It opens up alternative ideas for the major components that although are sometimes not practical in this application, show that the researcher has exhausted all engineering and functionality thoughts. Further concepts were then designed and developed for the entire HSDS unit based on previous practice and theory. In the future, it would be envisaged that both the Prototype and Production version of the HSDS would utilise standard industry available components, manufactured and distributed locally. Future research and testing of the prototype unit could result in a successful trial unit being incorporated in a working food processing production environment. Recommendations and future works are discussed, along with options in other food processing and packaging disciplines, and other areas in the non-food processing industry.

Associations between socioeconomic position, food insecurity and BMI

Introduction: Food insecurity is a social determinant of health and is defined as limited ability to access sufficient amounts of nutritionally adequate or safe food for a healthy and active life. Food insecurity is associated with poor health status and the exacerbation of other health inequalities. This study examined whether an association existed between 1) socioeconomic position (SEP) and food insecurity and 2) food insecurity and weight status. Methods: Data from the 1995 National Nutrition Survey was analysed. A random sample of households (n = 13 858) were asked about dietary habits and food choices. Information about gender, age, BMI, waist circumference, household income and whether the household had run out of money to purchase food in the previous 12 months was obtained and analysed using chi-square and logistic regression. Results: Income was significantly associated with food insecurity; households with lower income were at higher risk of food insecurity. Lower income males were nine times more likely to experience food insecurity and lower income females were three times more likely to experience food insecurity than their higher income counterparts. Food insecurity was significantly associated with body mass index (BMI) among women but not men. Women experiencing food insecurity were at higher risk of overweight/obesity according to BMI and waist circumference measures. Conclusion: Evidence suggests that low income households are at higher risk of food insecurity and women who are food insecure are at higher risk of being overweight or obese. Food insecurity may mediate the association between SEP and BMI.

Smoking status as a moderator of the association between food insecurity and decreased fruit and vegetable consumption

Food insecurity is the inadequate access to, or availability of, sufficient amounts of nutritious, culturally-appropriate and safe foods, or the inability to acquire such foods by socially acceptable means. Food insecurity has been shown to be associated with poor dietary intakes and poor health status. Recently, evidence has emerged suggesting increased rates of food insecurity among those with substance abuse problems, including those who smoke. This cross-sectional study investigates the potential moderating effect of smoking on the association between food insecurity and fruit and vegetable intakes among the Australian population, using regression analyses. Participants were adults 18 years and older participating in the 2004/05 National Health Survey (n = 19,500). Those from food insecure households were up to two-times more likely to report inadequate fruit and vegetable intakes compared to those who were food secure. Those who smoked were nearly six times more likely to report being food insecure, and up to three-times more likely to report inadequate fruit and vegetable intakes, compared to their non-smoking counterparts. Further analyses revealed a marked decline in the strength of the association between food insecurity and fruit consumption with the addition of smoking status into a regression model. These findings have important implications for the development of policy and interventions to address food insecurity, suggesting that those from food insecure households are less likely to comply with national dietary recommendations, and that this may in part be moderated by smoking status.

Effect of moisture and temperature distribution on dried food microstructure and porosity

Dehydration of food materials requires water removal from it. This removal of moisture prevents the growth and reproduction of microorganisms that cause decay and minimizes many of the moisture-driven deterioration reactions (Brennan, 1994). However, during food drying, many other changes occur simultaneously resulting in a modified overall quality (Kompany et al., 1993). Among the physical attributes of dried food material porosity and microstructure are the important ones that can dominant other quality of dried foods (Aguilera et al., 2000). In addition, this two concerned quality attributes affected by process conditions, material components and raw structure of food stuff. In this work, temperature moisture distribution within food materials during microwave drying will be taken into consideration to observe its participation on the microstructure and porosity of the finished product. Apple is the selective materials for this work. Generally, most of the food materials are found in non-uniformed moisture contained condition. To develop non uniform temperature distribution, food materials have been dried in a microwave oven with different power levels (Chua et al., 2000). First of all, temperature and moisture model is simulated by COMSOL Multiphysics. Later on, digital imaging camera and Image Pro Premier software have been deployed to observation moisture distribution and thermal imaging camera for temperature distribution. Finally, Microstructure and porosity of the food materials are obtained from scanning electron microscope and porosity measuring devices respectively . Moisture distribution and temperature during drying influence the microstructure and porosity significantly. Specially, High temperature and moisture contained regions show less porosity and more rupture. These findings support other literatures of Halder et al. (2011) and Rahman et al (1990). On the other hand, low temperature and moisture regions depict uniform microstructure and high porosity. This work therefore assists in better understanding of the role of moisture and temperature distribution to a prediction of micro structure and porosity of dried food materials.

In-cylinder pressure and inter-cycle variability analysis for a compression ignition engine : Bayesian approaches

This thesis introduced Bayesian statistics as an analysis technique to isolate resonant frequency information in in-cylinder pressure signals taken from internal combustion engines. Applications of these techniques are relevant to engine design (performance and noise), energy conservation (fuel consumption) and alternative fuel evaluation. The use of Bayesian statistics, over traditional techniques, allowed for a more in-depth investigation into previously difficult to isolate engine parameters on a cycle-by-cycle basis. Specifically, these techniques facilitated the determination of the start of pre-mixed and diffusion combustion and for the in-cylinder temperature profile to be resolved on individual consecutive engine cycles. Dr Bodisco further showed the utility of the Bayesian analysis techniques by applying them to in-cylinder pressure signals taken from a compression ignition engine run with fumigated ethanol.

Design LED innovation to rejuvenate local food systems and healthy communities : an emerging research agenda

Food Sovereignty (food freedom) is about empowering people to develop their own local food system. Food Sovereignty challenges designers to enable people to innovate the local food system, rather than having a food system which is dictated by corporate interests and failed business ethics. Communities are realising the potential for design to assist in the innovation process, and add strategic value to potentially localise the food system. Design Led Innovation (DLI) offers a strategic framework to address large-scale cultural, systemic and economic changes. The DLI approach empowers communities to take organised action to achieve a healthy, prosperous and happy way of life. DLI can assist with business models in the business world and it is evident this approach can assist with creating social change too. This paper presents on an emerging research agenda aimed to assist designer’s focus from individuals and systems to communities and urban problems. This paper also presents the research proposition that DLI and service design coupled with social entrepreneurial ventures such as local food projects and creative community inventions, have the potential to enable social innovation for healthy and happy communities.