The organic fraction of bubble-generated, accumulation mode Sea Spray Aerosol (SSA)

Recent studies have detected a dominant accumulation mode (~100 nm) in the Sea Spray Aerosol (SSA) number distribution. There is evidence to suggest that particles in this mode are composed primarily of organics. To investigate this hypothesis we conducted experiments on NaCl, artificial SSA and natural SSA particles with a Volatility-Hygroscopicity-Tandem-Differential-Mobility-Analyser (VH-TDMA). NaCl particles were atomiser generated and a bubble generator was constructed to produce artificial and natural SSA particles. Natural seawater samples for use in the bubble generator were collected from biologically active, terrestrially-affected coastal water in Moreton Bay, Australia. Differences in the VH-TDMA-measured volatility curves of artificial and natural SSA particles were used to investigate and quantify the organic fraction of natural SSA particles. Hygroscopic Growth Factor (HGF) data, also obtained by the VH-TDMA, were used to confirm the conclusions drawn from the volatility data. Both datasets indicated that the organic fraction of our natural SSA particles evaporated in the VH-TDMA over the temperature range 170–200°C. The organic volume fraction for 71–77 nm natural SSA particles was 8±6%. Organic volume fraction did not vary significantly with varying water residence time (40 secs to 24 hrs) in the bubble generator or SSA particle diameter in the range 38–173 nm. At room temperature we measured shape- and Kelvin-corrected HGF at 90% RH of 2.46±0.02 for NaCl, 2.35±0.02 for artifical SSA and 2.26±0.02 for natural SSA particles. Overall, these results suggest that the natural accumulation mode SSA particles produced in these experiments contained only a minor organic fraction, which had little effect on hygroscopic growth. Our measurement of 8±6% is an order of magnitude below two previous measurements of the organic fraction in SSA particles of comparable sizes. We stress that our results were obtained using coastal seawater and they can’t necessarily be applied on a regional or global ocean scale. Nevertheless, considering the order of magnitude discrepancy between this and previous studies, further research with independent measurement techniques and a variety of different seawaters is required to better quantify how much organic material is present in accumulation mode SSA.

Bubble rise velocity and trajectory in xanthan gum crystal suspension

An experimental set-up was used to visually observe the characteristics of bubbles as they moved up a column holding xanthan gum crystal suspensions. The bubble rise characteristics in xanthan gum solutions with crystal suspension are presented in this paper. The suspensions were made by using different concentrations of xanthan gum solutions with 0.23 mm mean diameter polystyrene crystal particles. The influence of the dimensionless quantities; namely the Reynolds number, Re, the Weber number, We, and the drag co-efficient, cd, are identified for the determination of the bubble rise velocity. The effect of these dimensionless groups together with the Eötvös number, Eo, the Froude number, Fr, and the bubble deformation parameter, D, on the bubble rise velocity and bubble trajectory are analysed. The experimental results show that the average bubble velocity increases with the increase in bubble volume for xanthan gum crystal suspensions. At high We, Eo and Re, bubbles are spherical-capped and their velocities are found to be very high. At low We and Eo, the surface tension force is significant compared to the inertia force. The viscous forces were shown to have no substantial effect on the bubble rise velocity for 45 < Re < 299. The results show that the drag co-efficient decreases with the increase in bubble velocity and Re. The trajectory analysis showed that small bubbles followed a zigzag motion while larger bubbles followed a spiral motion. The smaller bubbles experienced less horizontal motion in crystal suspended xanthan gum solutions while larger bubbles exhibited a greater degree of spiral motion than those seen in the previous studies on the bubble rise in xanthan gum solutions without crystal.

Bubble geometry and chaotic pricing behaviour

This paper is a deductive theoretical enquiry into the flow of effects from the geometry of price bubbles/busts, to price indices, to pricing behaviours of sellers and buyers, and back to price bubbles/busts. The intent of the analysis is to suggest analytical approaches to identify the presence, maturity, and/or sustainability of a price bubble. We present a pricing model to emulate market behaviour, including numeric examples and charts of the interaction of supply and demand. The model extends into dynamic market solutions myopic (single- and multi-period) backward looking rational expectations to demonstrate how buyers and sellers interact to affect supply and demand and to show how capital gain expectations can be a destabilising influence – i.e. the lagged effects of past price gains can drive the market price away from long-run market-worth. Investing based on the outputs of past price-based valuation models appear to be more of a game-of-chance than a sound investment strategy.

Discrete choice modelling of combined mode and departure time

Typical daily decision-making process of individuals regarding use of transport system involves mainly three types of decisions: mode choice, departure time choice and route choice. This paper focuses on the mode and departure time choice processes and studies different model specifications for a combined mode and departure time choice model. The paper compares different sets of explanatory variables as well as different model structures to capture the correlation among alternatives and taste variations among the commuters. The main hypothesis tested in this paper is that departure time alternatives are also correlated by the amount of delay. Correlation among different alternatives is confirmed by analyzing different nesting structures as well as error component formulations. Random coefficient logit models confirm the presence of the random taste heterogeneity across commuters. Mixed nested logit models are estimated to jointly account for the random taste heterogeneity and the correlation among different alternatives. Results indicate that accounting for the random taste heterogeneity as well as inter-alternative correlation improves the model performance.

Unpacking Japan's 21st century "National Conversation" : images of the future beyond the iron cage of the "Catch Up" model

How does the image of the future operate upon history, and upon national and individual identities? To what extent are possible futures colonized by the image? What are the un-said futurecratic discourses that underlie the image of the future? Such questions inspired the examination of Japan’s futures images in this thesis. The theoretical point of departure for this examination is Polak’s (1973) seminal research into the theory of the ‘image of the future’ and seven contemporary Japanese texts which offer various alternative images for Japan’s futures, selected as representative of a ‘national conversation’ about the futures of that nation. These seven images of the future are: 1. Report of the Prime Minister’s Commission on Japan’s Goals in the 21st Century—The Frontier Within: Individual Empowerment and Better Governance in the New Millennium, compiled by a committee headed by Japan’s preeminent Jungian psychologist Kawai Hayao (1928-2007); 2. Slow Is Beautiful—a publication by Tsuji Shinichi, in which he re-images Japan as a culture represented by the metaphor of the sloth, concerned with slow and quality-oriented livingry as a preferred image of the future to Japan’s current post-bubble cult of speed and economic efficiency; 3. MuRatopia is an image of the future in the form of a microcosmic prototype community and on-going project based on the historically significant island of Awaji, and established by Japanese economist and futures thinker Yamaguchi Kaoru; 4. F.U.C.K, I Love Japan, by author Tanja Yujiro provides this seven text image of the future line-up with a youth oriented sub-culture perspective on that nation’s futures; 5. IMAGINATION / CREATION—a compilation of round table discussions about Japan’s futures seen from the point of view of Japan’s creative vanguard; 6. Visionary People in a Visionless Country: 21 Earth Connecting Human Stories is a collection of twenty one essays compiled by Denmark born Tokyo resident Peter David Pedersen; and, 7. EXODUS to the Land of Hope, authored by Murakami Ryu, one of Japan’s most prolific and influential writers, this novel suggests a future scenario portraying a massive exodus of Japan’s youth, who, literate with state-of-the-art information and communication technologies (ICTs) move en masse to Japan’s northern island of Hokkaido to launch a cyber-revolution from the peripheries. The thesis employs a Futures Triangle Analysis (FTA) as the macro organizing framework and as such examines both pushes of the present and weights from the past before moving to focus on the pulls to the future represented by the seven texts mentioned above. Inayatullah’s (1999) Causal Layered Analysis (CLA) is the analytical framework used in examining the texts. Poststructuralist concepts derived primarily from the work of Michel Foucault are a particular (but not exclusive) reference point for the analytical approach it encompasses. The research questions which reflect the triangulated analytic matrix are: 1. What are the pushes—in terms of current trends—that are affecting Japan’s futures? 2. What are the historical and cultural weights that influence Japan’s futures? 3. What are the emerging transformative Japanese images of the future discourses, as embodied in actual texts, and what potential do they offer for transformative change in Japan? Research questions one and two are discussed in Chapter five and research question three is discussed in Chapter six. The first two research questions should be considered preliminary. The weights outlined in Chapter five indicate that the forces working against change in Japan are formidable, structurally deep-rooted, wide-spread, and under-recognized as change-adverse. Findings and analyses of the push dimension reveal strong forces towards a potentially very different type of Japan. However it is the seven contemporary Japanese images of the future, from which there is hope for transformative potential, which form the analytical heart of the thesis. In analyzing these texts the thesis establishes the richness of Japan’s images of the future and, as such, demonstrates the robustness of Japan’s stance vis-à-vis the problem of a perceived map-less and model-less future for Japan. Frontier is a useful image of the future, whose hybrid textuality, consisting of government, business, academia, and creative minority perspectives, demonstrates the earnestness of Japan’s leaders in favour of the creation of innovative futures for that nation. Slow is powerful in its aim to reconceptualize Japan’s philosophies of temporality, and build a new kind of nation founded on the principles of a human-oriented and expanded vision of economy based around the core metaphor of slowness culture. However its viability in Japan, with its post-Meiji historical pushes to an increasingly speed-obsessed social construction of reality, could render it impotent. MuRatopia is compelling in its creative hybridity indicative of an advanced IT society, set in a modern day utopian space based upon principles of a high communicative social paradigm, and sustainability. IMAGINATION / CREATION is less the plan than the platform for a new discussion on Japan’s transformation from an econo-centric social framework to a new Creative Age. It accords with emerging discourses from the Creative Industries, which would re-conceive of Japan as a leading maker of meaning, rather than as the so-called guzu, a term referred to in the book meaning ‘laggard’. In total, Love Japan is still the most idiosyncratic of all the images of the future discussed. Its communication style, which appeals to Japan’s youth cohort, establishes it as a potentially formidable change agent in a competitive market of futures images. Visionary People is a compelling image for its revolutionary and subversive stance against Japan’s vision-less political leadership, showing that it is the people, not the futures-making elite or aristocracy who must take the lead and create a new vanguard for the nation. Finally, Murakami’s Exodus cannot be ruled out as a compelling image of the future. Sharing the appeal of Tanja’s Love Japan to an increasingly disenfranchised youth, Exodus portrays a near-term future that is achievable in the here and now, by Japan’s teenagers, using information and communications technologies (ICTs) to subvert leadership, and create utopianist communities based on alternative social principles. The principal contribution from this investigation in terms of theory belongs to that of developing the Japanese image of the future. In this respect, the literature reviews represent a significant compilation, specifically about Japanese futures thinking, the Japanese image of the future, and the Japanese utopia. Though not exhaustive, this compilation will hopefully serve as a useful starting point for future research, not only for the Japanese image of the future, but also for all image of the future research. Many of the sources are in Japanese and their English summations are an added reason to respect this achievement. Secondly, the seven images of the future analysed in Chapter six represent the first time that Japanese image of the future texts have been systematically organized and analysed. Their translation from Japanese to English can be claimed as a significant secondary contribution. What is more, they have been analysed according to current futures methodologies that reveal a layeredness, depth, and overall richness existing in Japanese futures images. Revealing this image-richness has been one of the most significant findings of this investigation, suggesting that there is fertile research to be found from this still under-explored field, whose implications go beyond domestic Japanese concerns, and may offer fertile material for futures thinkers and researchers, Japanologists, social planners, and policy makers.

Drag coefficient in a crystal suspension

A single air bubble rising in xanthan gum crystal suspension has been studied experimentally. The suspension was made by different concentrations of xanthan gum solutions with 0.23 mm polystyrene crystal particles. Drag co-efficient data and a new correlation of drag coefficient is presented for spherical and nonspherical bubbles in non-Newtonian crystal suspension. The correlation is developed in terms of the Reynolds number, Re and the bubble shape factor, � (the ratio between the surface equivalent sphere diameter to the volume equivalent sphere diameter). The experimental drag coefficient was found to be consistent with this new predicted correlation and published data over the ranges, 0.1

Influence of field size on pupil diameter under photopic and mesopic light levels

Purpose: We investigated the interaction between adapting field size and luminance on pupil diameter when cones alone (photopic) or rods and cones (mesopic) were active. Method: Circular achromatic targets (1o to 24o diameter) were presented to eight young participants on a rectangular projector screen. The accommodative influence on pupil diameter was minimized using cycloplegia in the fixing right eye and the consensual pupil reflex was measured in the left eye. Target luminance was adjusted for each stimulus such that corneal flux density (product of field area and luminance) was constant at 3600 cd.deg2m-2 (photopic condition) and 1.49 cd.deg2m-2 (mesopic condition). Results: There were no statistically significant effects of adaptive field size on pupil diameter for either condition. Conclusion: If corneal flux density is kept constant, there will be no change in pupil diameter as the size of the stimulus field increases at either mesopic or photopic lighting levels up to at least 24°.

Effect of cold water immersion after exercise in the heat on muscle function, body temperatures, and vessel diameter

Cold water immersion (CWI) is a popular recovery modality, but actual physiological responses to CWI after exercise in the heat have not been well documented. The purpose of this study was to examine effects of 20-min CWI (14 degrees C) on neuromuscular function, rectal (T(re)) and skin temperature (T(sk)), and femoral venous diameter after exercise in the heat. Ten well-trained male cyclists completed two bouts of exercise consisting of 90-min cycling at a constant power output (216+/-12W) followed by a 16.1km time trial (TT) in the heat (32 degrees C). Twenty-five minutes post-TT, participants were assigned to either CWI or control (CON) recovery conditions in a counterbalanced order. T(re) and T(sk) were recorded continuously, and maximal voluntary isometric contraction torque of the knee extensors (MVIC), MVIC with superimposed electrical stimulation (SMVIC), and femoral venous diameters were measured prior to exercise, 0, 45, and 90min post-TT. T(re) was significantly lower in CWI beginning 50min post-TT compared with CON, and T(sk) was significantly lower in CWI beginning 25min post-TT compared with CON. Decreases in MVIC, and SMVIC torque after the TT were significantly greater for CWI compared with CON; differences persisted 90min post-TT. Femoral vein diameter was approximately 9% smaller for CWI compared with CON at 45min post-TT. These results suggest that CWI decreases T(re), but has a negative effect on neuromuscular function.

Bubble extinction in Hele-Shaw flow with surface tension and kinetic undercooling regularisation

We perform an analytic and numerical study of an inviscid contracting bubble in a two-dimensional Hele-Shaw cell, where the effects of both surface tension and kinetic undercooling on the moving bubble boundary are not neglected. In contrast to expanding bubbles, in which both boundary effects regularise the ill-posedness arising from the viscous (Saffman-Taylor) instability, we show that in contracting bubbles the two boundary effects are in competition, with surface tension stabilising the boundary, and kinetic undercooling destabilising it. This competition leads to interesting bifurcation behaviour in the asymptotic shape of the bubble in the limit it approaches extinction. In this limit, the boundary may tend to become either circular, or approach a line or "slit" of zero thickness, depending on the initial condition and the value of a nondimensional surface tension parameter. We show that over a critical range of surface tension values, both these asymptotic shapes are stable. In this regime there exists a third, unstable branch of limiting self-similar bubble shapes, with an asymptotic aspect ratio (dependent on the surface tension) between zero and one. We support our asymptotic analysis with a numerical scheme that utilises the applicability of complex variable theory to Hele-Shaw flow.

An accurate numerical scheme for the contraction of a bubble in a Hele-Shaw cell

We report on an accurate numerical scheme for the evolution of an inviscid bubble in radial Hele-Shaw flow, where the nonlinear boundary effects of surface tension and kinetic undercooling are included on the bubble-fluid interface. As well as demonstrating the onset of the Saffman-Taylor instability for growing bubbles, the numerical method is used to show the effect of the boundary conditions on the separation (pinch-off) of a contracting bubble into multiple bubbles, and the existence of multiple possible asymptotic bubble shapes in the extinction limit. The numerical scheme also allows for the accurate computation of bubbles which pinch off very close to the theoretical extinction time, raising the possibility of computing solutions for the evolution of bubbles with non-generic extinction behaviour.

Mathematical models of bubble evolution in a Hele-Shaw Cell

This thesis concerns the mathematical model of moving fluid interfaces in a Hele-Shaw cell: an experimental device in which fluid flow is studied by sandwiching the fluid between two closely separated plates. Analytic and numerical methods are developed to gain new insights into interfacial stability and bubble evolution, and the influence of different boundary effects is examined. In particular, the properties of the velocity-dependent kinetic undercooling boundary condition are analysed, with regard to the selection of only discrete possible shapes of travelling fingers of fluid, the formation of corners on the interface, and the interaction of kinetic undercooling with the better known effect of surface tension. Explicit solutions to the problem of an expanding or contracting ring of fluid are also developed.

Rapid synthesis of porous honeycomb Cu/Pd through a hydrogen-bubble templating method

A rapid electrochemical method based on using a clean hydrogen-bubble template to form a bimetallic porous honeycomb Cu/Pd structure has been investigated. The addition of palladium salt to a copper-plating bath under conditions of vigorous hydrogen evolution was found to influence the pore size and bulk concentration of copper and palladium in the honeycomb bimetallic structure. The surface was characterised by X-ray photoelectron spectroscopy, which revealed that the surface of honeycomb Cu/Pd was found to be rich with a Cu/Pd alloy. The inclusion of palladium in the bimetallic structure not only influenced the pore size, but also modified the dendritic nature of the internal wall structure of the parent copper material into small nanometre-sized crystallites. The chemical composition of the bimetallic structure and substantial morphology changes were found to significantly influence the surface-enhanced Raman spectroscopic response for immobilised rhodamine B and the hydrogen-evolution reaction. The ability to create free-standing films of this honeycomb material may also have many advantages in the areas of gas- and liquid-phase heterogeneous catalysis.

Through-focus performance with multifocal contact lenses : effect of binocularity, pupil diameter and inherent ocular aberrations

Purpose to evaluate the effects of the wearer’s pupil size and spherical aberration on visual performance with centre-near, aspheric multifocal contact lenses (MFCLs). The advantage of binocular over monocular vision was also investigated. Methods Twelve young volunteers, with an average age of 27±5 years, participated in the study. LogMAR Visual Acuity (VA) was measured under cycloplegia for a range of defocus levels (from +3.0 to -3.0D, in 0.5D steps) with no correction and with three aspheric MFCLs (Air Optix Aqua Multifocal, Ciba Vision, Duluth, GA, US) with a centre-near design, providing correction for “Low”, “Med” and “High” near demands. Measurements were performed for all combinations of the following conditions: i) artificial pupils of 6mm and 3mm diameter, ii) binocular and monocular (dominant eye) vision. Depth-of-focus (DOF) was calculated from the VA vs. defocus curves. Ocular aberrations under cycloplegia were measured using iTrace. Results VA at -3.0D defocus (simulating near performance) was statistically higher for the 3mm than for the 6mm pupil (p=0.006), and for binocular rather than for monocular vision (p<0.001). Similarly, DOF was better for the 3mm pupil (p=0.002) and for binocular viewing conditions (p<0.001, ANOVA). Both VA at –3.0D defocus and DOF increased as the “addition” of the MFCL correction increased. Finally, with the centre-near MFCLs a linear correlation was found between VA at –3.0D defocus and the wearer’s ocular spherical aberration (R2=0.20 p<0.001 for 6mm data), with the eyes exhibiting the higher positive spherical aberration experiencing lower VAs. By contrast, no correlation was found between VA and spherical aberration at 0.00D defocus (distance vision). Conclusions Both near VA and depth-of-focus improve with these MFCLs, with the effects being more pronounced for small pupils and binocular than for monocular vision. Coupling of the wearer’s ocular spherical aberration with the aberration profiles provided by MFCLs affects their functionality.

Measurement of the first neutron diffraction peak of D2O flowing in a 2 mm diameter aluminium tube as a function of temperature

A pilot experiment was performed using the WOMBAT powder diffraction instrument at ANSTO in which the first neutron diffraction peak (Q0) was measured for D2O flowing in a 2 mm internal diameter aluminium tube. Measurements of Q0 were made at -9, 4.3, 6.9, 12, 18.2 and 21.5 °C. The D2O was circulated using a siphon with water in the lower reservoir returned to the upper reservoir using a small pump. This enabled stable flow to be maintained for several hours. For example, if the pump flow increased slightly, the upper reservoir level rose, increasing the siphon flow until it matched the return flow. A neutron wavelength of 2.4 Å was used and data integrated over 60 minutes for each temperature. A jet of nitrogen from a liquid N2 Dewar was directed over the aluminium tube to vary water temperature. After collection of the data, the d spacing of the aluminium peaks was used to calculate the temperature of the aluminium within the neutron beam and therefore was considered to be an accurate measure of water temperature within the beam. Sigmaplot version 12.3 was used to fit a Weibull five parameter peak fit to the first neutron diffraction peak. The values of Q0 obtained in this experiment showed an increase with temperature consistent with data in the literature [1] but were consistently higher than published values for bulk D20. For example at 21.5 °C we obtained a value of 2.008 Å-1 for Q0 compared to a literature value of 1.988 Å-1 for bulk D2O at 20 °C, a difference of 1%. Further experiments are required to see if this difference is real or artifactual.

The effect of electrode material on the electrochemical formation of porous copper surfaces using hydrogen bubble templating

The electrodeposition of copper onto copper, gold, palladium and glassy carbon (GC) electrodes via a hydrogen bubble templating method is reported. It is found that the composition of the underlying electrode material significantly influences the morphology of the copper electrodeposit. Highly ordered porous structures are achieved with Cu and Au electrodes, however on Pd this order is disrupted and a rough randomly oriented surface is formed whereas on GC a bubble templating effect is not observed. Chronopotentiograms recorded during the electrodeposition process allows bubble formation and detachment from the surface to be monitored where distinctly different potential versus time profiles are observed at the different electrodes. The porous Cu surfaces are characterised with scanning electron microscopy, X-ray diffraction and cyclic voltammetric measurements recorded under alkaline conditions. The latter demonstrates that there are active sites present on electrodeposited copper whose coverage and reactivity depend on the underlying electrode material. The most active Cu surface is achieved at a Pd substrate for both the hydrogen evolution reaction and the catalytic reduction of ferricyanide ions with thiosulphate ions. This demonstrates that the highly ordered porous structure on the micron scale which typifies the morphology that can be achieved with the hydrogen bubbling template method is not required in producing the most effective material.