Produtos têxteis inteligentes incorporando filamentos compósitos com nanotubos de carbono

Programa Doutoral em Engenharia Têxtil.

Advances in thermoplastic pultruded composites

Pultrusion is a versatile continuous high speed production technology allowing the production of fibre reinforced complex profiles. Thermosetting resins are normally used as matrices in the production of structural constant cross section profiles. Although only recently thermoplastic matrices have been used in long and continuous fibre reinforced composites replacing with success thermosetting matrices, the number of their applications is increasing due to their better ecological and mechanical performance. Composites with thermoplastic matrices offers increased fracture toughness, higher impact tolerance, short processing cycle time and excellent environmental stability. They are recyclable, post-formable and can be joined by welding. The use of long/continuous fibre reinforced thermoplastic matrix composites involves, however, great technological and scientific challenges since thermoplastics present much higher viscosity than thermosettings, which makes much difficult and complex the impregnation of reinforcements and consolidation tasks. In this work continuous fibres reinforced thermoplastic matrix towpregs were produced using equipment developed by the Institute for Polymers and Composites (IPC). The processing of the towpregs was made by pultrusion, in a developed prototype equipment existing in the Engineering School of the Polytechnic Institute of Porto (ISEP). Different thermoplastic matrices and fibres raw-materials were used in this study to manufacture pultruded composites for commercial applications (glass and carbon fibre/ polypropylene) and for advanced markets (carbon fibre/Primospire®). To improve the temperature distribution profile in heating die, different modifications were performed. In order to optimize both processes, towpregs production and pultruded composites profiles were analysed to determine the influence of the most relevant processing arameters in the final properties. The final pultruded composite profiles were submitted to mechanical tests to obtain the relevant properties.

Microstructure and mechanical properties of carbon nanotube reinforced cementitious composites developed using a novel dispersion technique

The authors also acknowledge Centre for Textile Science and Technology (University of Minho) and FIBRENAMICS PLATFORMfor providing required conditions for this research. Sincere thanks are also due to Mr. Pedro Samuel Leite and Mr. Carlos Jesus for their kind help in sample preparation and testing.

Enzymatic treatments to improve mechanical properties and surface hydrophobicity of jute fiber membranes

Fiber membranes prepared from jute fragments can be valuable, low cost, and renewable. They have broad application prospects in packing bags, geotextiles, filters, and composite reinforcements. Traditionally, chemical adhesives have been used to improve the properties of jute fiber membranes. A series of new laccase, laccase/mediator systems, and multi-enzyme synergisms were attempted. After the laccase treatment of jute fragments, the mechanical properties and surface hydrophobicity of the produced fiber membranes increased because of the cross-coupling of lignins with ether bonds mediated by laccase. The optimum conditions were a buffer pH of 4.5 and an incubation temperature of 60 °C with 0.92 U/mL laccase for 3 h. Laccase/guaiacol and laccase/alkali lignin treatments resulted in remarkable increases in the mechanical properties; in contrast, the laccase/2,2-azino-bis-(3-ethylthiazoline-6-sulfonate) (ABTS) and laccase/2,6-dimethoxyphenol treatments led to a decrease. The laccase/ guaiacol system was favorable to the surface hydrophobicity of jute fiber membranes. However, the laccase/alkali lignin system had the opposite effect. Xylanase/laccase and cellulase/laccase combined treatments were able to enhance both the mechanical properties and the surface hydrophobicity of jute fiber membranes. Among these, cellulase/laccase treatment performed better; compared to mechanical properties, the surface hydrophobicity of the jute fiber membranes showed only a slight increase after the enzymatic multi-step processes.

Stress, cognitive appraisal, and psychological health: testing instruments for health professionals

The job of health professionals, including nurses, is considered inherently stressful (Lee & Wang, 2002; Rutledge et al., 2009), and thus it is important to improve and develop specific measures that are sensitive to the demands that health professionals face. This study analysed the psychometric properties of three instruments that focus on the professional experiences of nurses in aspects related to occupational stress, cognitive appraisal, and mental health issues. The evaluation protocol included the Stress Questionnaire for Health Professionals (SQHP; Gomes, 2014), the Cognitive Appraisal Scale (CAS; Gomes, Faria, & Gonçalves, 2013), and the General Health Questionnaire-12 (GHQ-12; Goldberg, 1972). Validity and reliability issues were considered with statistical analysis (i.e. confirmatory factor analysis, convergent validity, and composite reliability) that revealed adequate values for all of the instruments, namely, a six-factor structure for the SQHP, a five-factor structure for the CAS, and a two-factor structure for the GHQ-12. In conclusion, this study proposes three consistent instruments that may be useful for analysing nurses’ adaptation to work contexts.

The tutor's role in student learning

Higher education in Portugal, in the last forty years, has undergone profound changes with the enlargement of public higher education network, the appearance of new institutions, the quantity and the heterogeneity of students. The implementation of the Bologna Process in European community countries led to the redesign of higher education Portuguese courses as well as their corresponding curricula. In recent years, the use of Project-led education was one of the most significant changes in teaching and learning, particularly in engineering in higher education in Portugal. This teaching methodology encourages students and teachers to undertake new roles, new responsibilities and a new learning perspective. This study aims at understanding whether the role of the tutor is to be suitable to the needs and expectations of Project-led education students. These changes however are not only structural. At the University of Minho, new teaching and learning methodologies were adopted, which could guide the training of professionals on to the twenty-first century. The opportunity arising from the implementation of Project-led education in Engineering methodology was used in the University of Minho’s courses. This teaching method is intended to provide students with educational support programs that benefit the academic performance, allowing the opportunity to upgrade, train and develop the ability to study and learn more effectively. Through the Project-led education it is possible to provide students with techniques and procedures and develop the ability to communicate orally and in writing. Students and teachers have assumed new roles in the teaching-learning process allowing in one hand the students to explore, discover and question themselves about some knowledge and on the other hand the teachers to change to a tutor, a companion and to a student project guide. Therefore, surveys were analyzed, comprising questions about the most significant contribution of the tutor as well as if there are some initial expectations that have not been foreseen by the tutor.

Educação bilingue em Moçambique: um estudo de caso, na Província de Gaza, centrado nas práticas pedagógicas do ensino básico

Em contextos como o de Moçambique que apresenta uma diversidade linguística, o uso de mais de uma língua no ensino é quase que obrigatório. Assim, urge a necessidade de formalizar a Educação Bilingue (EB) nas escolas moçambicanas. A modalidade de EB em Moçambique é de transição e manutenção, nas primeiras classes (1ª, 2ª e 3ª) usa-se a língua local como meio de instrução e o Português é uma disciplina, a partir da 4ª classe há uma inversão. Dessa estratégia o aluno deve estar em condições na 5ª classe de enfrentar o exame nacional, que é feito em língua oficial Portuguesa, para transitar do 1º para o 2º grau. O trabalho tem como problema esta interrogação: De que modo o programa curricular de Educação Bilingue se traduz nas práticas pedagógicas nas escolas do Ensino Básico que usam a língua Portuguesa e Changana no distrito de Bilene, na província de Gaza? O estudo empírico é de natureza qualitativa e quantitativa, com a utilização de técnicas de recolha de dados como a análise documental, entrevistas, questionário e provas escrita e oral aos alunos. Do estudo conclui-se: i) Não existe um programa de base especificamente para EB; ii) Há incongruência entre o programa e as práticas pedagógicas e iii) Os alunos apresentam maior dificuldades de compreensão, na escrita do que na oralidade, nas provas de conhecimento nas disciplinas básicas (Português e Matemática) em língua Portuguesa.

Estudo do comportamento tribológico de materiais compósitos à base de titânio reforçado com partículas cerâmicas para aplicação em implantes articulares

Dissertação de mestrado integrado em Engenharia Biomédica

Biomimetic strategies to engineer mineralised human tissues

In the last few years, many reports have been describing promising biocompatible and biodegradable materials that can mimic in a certain extent the multidimensional hierarchical structure of bone, while are also capable of releasing bioactive agents or drugs in a controlled manner. Despite these great advances, new developments in the design and fabrication technologies are required to address the need to engineer suitable biomimetic materials in order tune cells functions, i.e. enhance cell-biomaterial interactions, and promote cell adhesion, proliferation, and differentiation ability. Scaffolds, hydrogels, fibres and composite materials are the most commonly used as biomimetics for bone tissue engineering. Dynamic systems such as bioreactors have also been attracting great deal of attention as it allows developing a wide range of novel in vitro strategies for the homogeneous coating of scaffolds and prosthesis with ceramics, and production of biomimetic constructs, prior its implantation in the body. Herein, it is overviewed the biomimetic strategies for bone tissue engineering, recent developments and future trends. Conventional and more recent processing methodologies are also described.

(Des)construindo práticas de escrita na aula de língua estrangeira com recurso às TIC

Relatório de estágio de mestrado em Ensino de Inglês e de Espanhol no 3º Ciclo do Ensino Básico e no Ensino Secundário

Flexural strengthening of RC beams using hybrid composite plate (HCP): experimental and analytical study

Hybrid Composite Plate (HCP) is a reliable recently proposed retrofitting solution for concrete structures, which is composed of a strain hardening cementitious composite (SHCC) plate reinforced with Carbon Fibre Reinforced Polymer (CFRP). This system benefits from the synergetic advantages of these two composites, namely the high ductility of SHCC and the high tensile strength of CFRPs. In the materialstructural of HCP, the ultra-ductile SHCC plate acts as a suitable medium for stress transfer between CFRP laminates (bonded into the pre-sawn grooves executed on the SHCC plate) and the concrete substrate by means of a connection system made by either chemical anchors, adhesive, or a combination thereof. In comparison with traditional applications of FRP systems, HCP is a retrofitting solution that (i) is less susceptible to the detrimental effect of the lack of strength and soundness of the concrete cover in the strengthening effectiveness; (ii) assures higher durability for the strengthened elements and higher protection to the FRP component in terms of high temperatures and vandalism; and (iii) delays, or even, prevents detachment of concrete substrate. This paper describes the experimental program carried out, and presents and discusses the relevant results obtained on the assessment of the performance of HCP strengthened reinforced concrete (RC) beams subjected to flexural loading. Moreover, an analytical approach to estimate the ultimate flexural capacity of these beams is presented, which was complemented with a numerical strategy for predicting their load-deflection behaviour. By attaching HCP to the beams’ soffit, a significant increase in the flexural capacity at service, at yield initiation of the tension steel bars and at failure of the beams can be achieved, while satisfactory deflection ductility is assured and a high tensile capacity of the CFRP laminates is mobilized. Both analytical and numerical approaches have predicted with satisfactory agreement, the load-deflection response of the reference beam and the strengthened ones tested experimentally.

Evaluation of the performance of recycled textile fibres in the mechanical behaviour of a gypsum and cork composite material

Given the need for using more sustainable constructive solutions, an innovative composite material based on a combination of distinct industrial by-products is proposed aiming to reduce waste and energy consumption in the production of construction materials. The raw materials are thermal activated flue-gas desulphurization (FGD) gypsum, which acts as a binder, granulated cork as the aggregate and recycled textile fibres from used tyres intended to reinforce the material. This paper presents the results of the design of the composite mortar mixes, the characterization of the key physical properties (density, porosity and ultrasonic pulse velocity) and the mechanical validation based on uniaxial compressive tests and fracture energy tests. In the experimental campaign, the influence of the percentage of the raw materials in terms of gypsum mass, on the mechanical properties of the composite material was assessed. It was observed that the percentage of granulated cork decreases the compressive strength of the composite material but contributes to the increase in the compressive fracture energy. Besides, the recycled textile fibres play an important role in the mode I fracture process and in the fracture energy of the composite material, resulting in a considerable increase in the mode I fracture energy.

Producing LFT composite parts for large consumption markets from thermoplastic powder-coated towpregs

Thermoplastic matrix composites are receiving increasing interest in last years. This is due to several advantageous properties and speed of processing of these materials as compared to their thermoset counterparts. Among thermoplastic composites, Long Fibre Thermoplastics (LFTs) have seen the fastest growth, mainly due to developments in the automotive sector. LFTs combine the (semi-)structural material properties of long (>1 cm) fibres, with the ease and speed of thermoplastic processing. This paper reports a study of a novel low-cost LFT technology and resulting composites. A patented powder-coating machine able to produce continuously pre-impregnated materials directly from fibre rovings and polymer powders was used to process glass-fibre reinforced polypropylene (GF/PP) towpregs. Such pre-impregnated materials were then chopped and used to make LFTs in a patented low-cost piston-blender developed by the Centre of Lightweight Structures, TUD-TNO, the Netherlands. The work allowed studying the most relevant towpreg production parameters and establishing the processing window needed to obtain a good quality GF/PP powder coated material. Finally, the processing window that allows producing LFTs of good quality in the piston-blender and the mechanical properties of final stamped GF/PP composite parts were also determined.

Design and optimization of an extrusion die for the production of wood–plastic composite profiles

In this work, the optimization of an extrusion die designed for the production of a wood–plastic composite (WPC) decking profile is investigated. The optimization was performed with the help of numerical tools, more precisely, by solving the continuity and momentum conservation equations that govern such flow, and aiming to balance properly the flow distribution at the extrusion die flow channel outlet. To capture the rheological behavior of the material, we used a Bird-Carreau model with parameters obtained from a fit to the (shear viscosity versus shearrate) experimental data, collected from rheological tests. To yield a balanced output flow, several numerical runs were performed by adjusting the flow restriction at different regions of the flow-channel parallel zone crosssection. The simulations were compared with the experimental results and an excellent qualitative agreement was obtained, allowing, in this way, to attain a good balancing of the output flow and emphasizing the advantages of using numerical tools to aid the design of profile extrusion dies.

One-step in situ synthesis of polyamide microcapsules with inorganic payload and their transformation into responsive thermoplastic composite materials

Well-dispersed loads of finely powdered metals, metal oxides, several carbon allotropes or nanoclays are incorporated into highly porous polyamide 6 microcapsules in controllable amounts via an original one-step in situ fabrication technique. It is based on activated anionic polymerization (AAP) of ε-caprolactam in a hydrocarbon solvent performed in the presence of the respective micro- or nanosized loads. The forming microcapsules with typical diameters of 25-50 µm entrap up to 40 wt% of load. Their melt processing produces hybrid thermoplastic composites. Mechanical, electric conductivity and magnetic response measurements show that transforming of in situ loaded microcapsules into composites by melt processing (MP) is a facile and rapid method to fabricate materials with high mechanical resistance and electro-magnetic characteristics sufficient for many industrial applications. This novel concept requires low polymerization temperatures, no functionalization or compatibilization of the loads and it is easy to scale up at industrial production levels.