Dispersion and re-agglomeration of graphite nanoplates in polypropylene melts under controlled flow conditions

The kinetics of GnP dispersion in polypropylene melt was studied using a prototype small scale modular extensional mixer. Its modular nature enabled the sequential application of a mixing step, melt relaxation, and a second mixing step. The latter could reproduce the flow conditions on the first mixing step, or generate milder flow conditions. The effect of these sequences of flow constraints upon GnP dispersion along the mixer length was studied for composites with 2 and 10 wt.% GnP. The samples collected along the first mixing zone showed a gradual decrease of number and size of GnP agglomerates, at a rate that was independent of the flow conditions imposed to the melt, but dependent on composition. The relaxation zone induced GnP re-agglomeration, and the application of a second mixing step caused variable dispersion results that were largely dependent on the hydrodynamic stresses generated.

Thermal conditions affecting heat transfer in FDM/FFE: a contribution towards the numerical modelling of the process

The performance of parts produced by Free Form Extrusion (FFE), an increasingly popular additive manufacturing technique, depends mainly on their dimensional accuracy, surface quality and mechanical performance. These attributes are strongly influenced by the evolution of the filament temperature and deformation during deposition and solidification. Consequently, the availability of adequate process modelling software would offer a powerful tool to support efficient process set-up and optimisation. This work examines the contribution to the overall heat transfer of various thermal phenomena developing during the manufacturing sequence, including convection and radiation with the environment, conduction with support and between adjacent filaments, radiation between adjacent filaments and convection with entrapped air. The magnitude of the mechanical deformation is also studied. Once this exercise is completed, it is possible to select the material properties, process variables and thermal phenomena that should be taken in for effective numerical modelling of FFE.

Weld lines in extrusion: Understanding the role of the flow conditions

This work reports the implemen tation and verification of a new so lver in OpenFOAM® open source computational library, able to cope w ith integral viscoelastic models based on the integral upper-convected Maxwell model. The code is verified through the comparison of its predictions with anal ytical solutions and numerical results obtained with the differential upper-convected Maxwell model

Shear strengthening of reinforced concrete beams with SHCC-FRP panels

Tese de Doutoramento em Engenharia Civil

Intra and inter-individual differences in social intelligence of Portuguese students

Social intelligence is a favorable condition for career decision-making and development. The social intelligence indices of Portuguese students in school years prior to a career transition are characterized and intra and interindividual differences are analyzed. Participants were 1095 students (552, 50.4% women) with a mean age of 14.78 years (SD = 1.86), in the 8th (542, 49.5%), 10th (295, 26.9%) and 11th (258, 23.6%) grades. The Cognitive Test of Social Intelligence (PCIS) was administered at two moments, six months apart. Results indicate that the 8th grade obtained higher average scores in Problem Solving, Motivation and Self-confidence (time 1), while the 10th grade obtained better results in Problem Solving, Motivation and Familiarity (time 2). Between the assessment moments, all school years register an increase in Problem Solving and Self-confidence in social situations. These results constitute favorable psychological conditions for the promotion of ethical questioning in career guidance interventions.

Project scheduling and cost minimization with multiple availability constrained resources under stochastic conditions

The authors propose a mathematical model to minimize the project total cost where there are multiple resources constrained by maximum availability. They assume the resources as renewable and the activities can use any subset of resources requiring any quantity from a limited real interval. The stochastic nature is inferred by means of a stochastic work content defined per resource within an activity and following a known distribution and the total cost is the sum of the resource allocation cost with the tardiness cost or earliness bonus in case the project finishes after or before the due date, respectively. The model was computationally implemented relying upon an interchange of two global optimization metaheuristics – the electromagnetism-like mechanism and the evolutionary strategies. Two experiments were conducted testing the implementation to projects with single and multiple resources, and with or without maximum availability constraints. The set of collected results shows good behavior in general and provide a tool to further assist project manager decision making in the planning phase.

Comparison of oleate conversion under microaerophilic and anaerobic conditions

Excessive accumulation of Long Chain Fatty Acids (LCFA) in methanogenic bioreactors is the cause of process failure associated to a severe decrease in methane production. In particular, fast and persistent accumulation of palmitate is critical and still not elucidated. Aerobes or facultative anaerobes were detected in those reactors, raising new questions on LCFA biodegradation. To get insight into the influence of oxygen, two bioreactors were operated under microaerophilic and anaerobic conditions, with oleate at 1 and 4 gCOD/(L d). Palmitate accumulated up to 2 and 16 gCOD/L in the anaerobic and microaerophilic reactor, respectively, which shows the importance of oxygen in this conversion. A second experiment was designed to understand the dynamics of oleate to palmitate conversion. A CSTR and a PFR were assembled in series and fed with oleate under microaerophilic conditions. HRT from 6 to 24 h were applied in the CSTR, and 14 to 52 min in the PFR. In the PFR a biofilm was formed where palmitate accounted for 82% of total LCFA. Pseudomonas was the predominant genus (42 %) in this biofilm, highlighting the role of aerobic and facultative anaerobic bacteria in LCFA bioconversion.

Wear of PEEK-Ti6Al4V systems under micro-abrasion and linear sliding conditions

Dissertação de mestrado integrado em Engenharia Biomédica

Enzymatic treatments to improve mechanical properties and surface hydrophobicity of jute fiber membranes

Fiber membranes prepared from jute fragments can be valuable, low cost, and renewable. They have broad application prospects in packing bags, geotextiles, filters, and composite reinforcements. Traditionally, chemical adhesives have been used to improve the properties of jute fiber membranes. A series of new laccase, laccase/mediator systems, and multi-enzyme synergisms were attempted. After the laccase treatment of jute fragments, the mechanical properties and surface hydrophobicity of the produced fiber membranes increased because of the cross-coupling of lignins with ether bonds mediated by laccase. The optimum conditions were a buffer pH of 4.5 and an incubation temperature of 60 °C with 0.92 U/mL laccase for 3 h. Laccase/guaiacol and laccase/alkali lignin treatments resulted in remarkable increases in the mechanical properties; in contrast, the laccase/2,2-azino-bis-(3-ethylthiazoline-6-sulfonate) (ABTS) and laccase/2,6-dimethoxyphenol treatments led to a decrease. The laccase/ guaiacol system was favorable to the surface hydrophobicity of jute fiber membranes. However, the laccase/alkali lignin system had the opposite effect. Xylanase/laccase and cellulase/laccase combined treatments were able to enhance both the mechanical properties and the surface hydrophobicity of jute fiber membranes. Among these, cellulase/laccase treatment performed better; compared to mechanical properties, the surface hydrophobicity of the jute fiber membranes showed only a slight increase after the enzymatic multi-step processes.

Regulamentação, concentração e instituições bancárias em contexto de crise

Dissertação de mestrado em Economia Monetária, Bancária e Financeira

Correction of the initial conditions

"Series title: Springerbriefs in applied sciences and technology, ISSN 2191-530X"

The effect of hydrodynamic conditions in Corynebacterium glutamicum growth

[Excerpt] Corynebacterium glutamicum is a facultative anaerobic, gram-positive bacterium with a GRAS status that grows fast and achieves high cell densities. C. glutamicum is commonly used in amino acids production, and is also able to convert sugars in organic acids (OA) and alcohols in specific conditions: anaerobic and limited-oxygen environments. In these conditions, the carbon metabolism is modified, namely the flux shifts from the pentose phosphate pathway to glycolysis and the TCA cycle flux decreases and consequently bacterial growth is strongly affected [1,2]. (...)

Inclusão escolar de alunos com necessidades educativas especiais: um estudo sobre as perceções de professores de educação física de escolas com sala de recursos multifuncionais na cidade de Manaus

Dissertação de mestrado em Educação Especial (área de especialização em Dificuldades de Aprendizagem Específicas)

Influence of oxygen conditions on bacterial interactions within biofilms related with cystic fibrosis

Dissertação de mestrado em Bioengineering

Evaluation of antimicrobial strategies against biomaterial-associated infections: impact of the surrounding environmental conditions

Dissertação de mestrado em Bioengenharia