Biomethanation of herbaceous biomass residues using 3-zone plug flow like digesters - A case study from India

Biomethanation of herbaceous biomass feedstock has the potential to provide clean energy source for cooking and other activities in areas where such biomass availability predominates. A biomethanation concept that involves fermentation of biomass residues in three steps, occurring in three zones of the fermentor is described. This approach while attempting take advantage of multistage reactors simplifies the reactor operation and obviates the need for a high degree of process control or complex reactor design. Typical herbaceous biomass decompose with a rapid VFA flux initially (with a tendency to float) followed by a slower decomposition showing balanced process of VFA generation and its utilization by methanogens that colonize biomass slowly. The tendency to float at the initial stages is suppressed by allowing previous days feed to hold it below digester liquid which permits VFA to disperse into the digester liquid without causing process inhibition. This approach has been used to build and operate simple biomass digesters to provide cooking gas in rural areas with weed and agro-residues. With appropriate modifications, the same concept has been used for digesting municipal solid wastes in small towns where large fermentors are not viable. With further modifications this concept has been used for solid-liquid feed fermentors. Methanogen colonized leaf biomass has been used as biofilm support to treat coffee processing wastewater as well as crop litter alternately in a year. During summer it functions as a biomass based biogas plants operating in the three-zone mode while in winter, feeding biomass is suspended and high strength coffee processing wastewater is let into the fermentor achieving over 90% BOD reduction. The early field experience of these fermentors is presented.

Application of the method of initial functions for the analysis of composite laminated plates

The method of initial functions has been applied for deriving higher order theories for cross-ply laminated composite thick rectangular plates. The equations of three-dimensional elasticity have been used. No a priori assumptions regarding the distribution of stresses or displacements are needed. Numerical solutions of the governing equations have been presented for simply supported edges and the results are compared with available ones.

Experience with Gasifiers for 3.7-kw Engines

Abstract is not available.

Working experience with a foundry solar furnace

Literature reveals that a low order priority has been given to foundry applications of the solar furnace for temperatures upto about 1000°C. In the present work, the performance of a solar furnace capable of melting small quantities of foundry-grade metals and alloys had been studied under various conditions. Crucibles of different materials and shapes were tried and the effect of having different heat-shield materials was also studied. Al---bronze crucible with cavity, and well-polished stainless stell heat-shield were found to be most effective in enhancing the efficiency of the furnace. Many important industrial applications of the present solar furnace, such as the recovery of metallic zinc from slags, had also been realised.

Hierarchical modelling of acclimatory processesstar, open

The term acclimation has been used with several connotations in the field of acclimatory physiology. An attempt has been made, in this paper, to define precisely the term “acclimation” for effective modelling of acclimatory processes. Acclimation is defined with respect to a specific variable, as cumulative experience gained by the organism when subjected to a step change in the environment. Experimental observations on a large number of variables in animals exposed to sustained stress, show that after initial deviation from the basal value (defined as “growth”), the variables tend to return to basal levels (defined as “decay”). This forms the basis for modelling biological responses in terms of their growth and decay. Hierarchical systems theory as presented by Mesarovic, Macko & Takahara (1970) facilitates modelling of complex and partially characterized systems. This theory, in conjunction with “growth-decay” analysis of biological variables, is used to model temperature regulating system in animals exposed to cold. This approach appears to be applicable at all levels of biological organization. Regulation of hormonal activity which forms a part of the temperature regulating system, and the relationship of the latter with the “energy” system of the animal of which it forms a part, are also effectively modelled by this approach. It is believed that this systematic approach would eliminate much of the current circular thinking in the area of acclimatory physiology.

P-T evolution of Glenelg eclogites, NW Scotland: Did they experience ultrahigh-pressure metamorphism?

Eclogites and their retrogressed equivalents from the eastern unit of the Glenelg-Attadale Inlier in NW Scotland preserve much microstructural evidence that indicates that very high-pressure/temperature eclogite facies conditions were reached, and followed by decompression and hydration during exhumation. Rutile exsolution in garnet and quartz exsolution in omphacite and titanite formed through mineral reactions during high P-T peak metamorphism. Isochemical phase diagrams modeled for samples from three different locations indicate that the outer part of the eastern unit preserves a peak metamorphic condition of c. 850-1000 degrees C at 18-25 kbar, whereas the central part has a similar pressure (c. 23 kbar), but a lower temperature (c. 670 degrees C). Due to the limitations in the phase diagram calculations the estimated P-T conditions represent the minimum conditions attained by the peak metamorphic assemblage, and the pre-exsoived peak assemblage probably stabilized at a higher pressure. This observation is strongly supported by the presence of exsolution microstructures. The present results demonstrate that the eastern unit experienced very high P-T conditions during peak metamorphism and a tight clockwise P-T trajectory and provide the first indication of possible ultrahigh-pressure metamorphism in the Glenelg eclogites. (C) 2009 Elsevier B.V. All rights reserved.

Structural studies of decaying fluid turbulence: Effect of initial conditions

We present results from a systematic numerical study of structural properties of an unforced, incompressible, homogeneous, and isotropic three-dimensional turbulent fluid with an initial energy spectrum that develops a cascade of kinetic energy to large wave numbers. The results are compared with those from a recently studied set of power-law initial energy spectra [C. Kalelkar and R. Pandit, Phys. Rev. E 69, 046304 (2004)] which do not exhibit such a cascade. Differences are exhibited in plots of vorticity isosurfaces, the temporal evolution of the kinetic energy-dissipation rate, and the rates of production of the mean enstrophy along the principal axes of the strain-rate tensor. A crossover between "non-cascade-type" and "cascade-type" behavior is shown numerically for a specific set of initial energy spectra.

Five-kilowatt wood gasifier technology: Evolution and field experience

Various elements of an efficient and reliable 5k W wood gasifier system developed over the last ten years are described. The good performance obtained from the system is related to the careful design of its components and sub-systems. Results from extensive testing of gasifier prototypes at two national centres are discussed along with the experience gained in the field from their use at more than one hundred and fifty locations spread over five states in the country. Issues related to acceptance of the technology are also included. Improvements in design to extend the life, to reduce the cost, and to reduce the number of components are also discussed. A few variants of the design to meet the specific requirements of water pumping, power generation and to exploit specific site characteristics are presented.

Ambiguity-free polarization measurements from mixture initial preparations

Starting from beam and target spin systems which are polarized in the usual way by applying external magnetic fields, measurements of appropriate final state tensor parameters, viz., {t0,1k, k=1,...,2j} of particle d with spin j in a reaction a+b→d+c1+c2+. . .are suggested to determine the reaction amplitudes in spin space free from any associated discrete ambiguity.

Room temperature creep in amorphous alloys: Influence of initial strain and free volume

The role of imposed strain on the room temperature time-dependent deformation behavior of bulk metallic glasses (BMGs) was systematically investigated through spherical nanoindentation creep experiments. The results show that creep occurred even at very low strains within elastic regimes and, interestingly, a precipitous increase in creep rate was found in plastic regimes, with BMG that had a higher free volume exhibiting greater creep rates. The results are discussed in terms of prevailing mechanisms of elastic/plastic deformation of amorphous alloys. (c) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Study of forging design using slip-line fields

The main purpose of forging design is to ensure cavity filling with minimum material wastage, minimum die load and minimum deformation energy. Given the desired shape of the component and the material to be forged, this goal is achieved by optimising the initial volume of the billet, the geometrical parameters of the die and the process parameters. It is general industrial practise to fix the initial billet volume and the die parameters using empirical relationships derived from practical experience. In this paper a basis for optimising some of the parameters for simple closed-die forging is proposed. Slip-line field solutions are used to predict the flow, the load and the energy in a simple two-dimensional closed-die forging operation. The influence of the design parameters; flash-land width, excess initial workpiece area and forged cross-sectional size; on complete cavity filling and efficient cavity filling are investigated. Using the latter as necessary requirements for forging, the levels of permissable design parameters are determined, the variation of these levels with the size of the cross-section then being examined.

A near-optimal initial seed value selection in K-means means algorithm using a genetic algorithm

The K-means algorithm for clustering is very much dependent on the initial seed values. We use a genetic algorithm to find a near-optimal partitioning of the given data set by selecting proper initial seed values in the K-means algorithm. Results obtained are very encouraging and in most of the cases, on data sets having well separated clusters, the proposed scheme reached a global minimum.