Properties of lime stabilised steam-cured blocks for masonry

The paper addresses certain issues pertaining to the technology of lime-stabilised steam-cured blocks used for masonry construction. Properties of lime-stabilised steam-cured blocks using expansive soils and tank bed soils have been examined. Influence of parameters like steam curing period, lime content and fly ash content on wet strength of blocks is studied. Steam curing of lime stabilised blocks at 80degreesC for about 20 hours at atmospheric pressure leads to considerably higher strengths when compared with curing under wet cloth at ambient temperatures. Clay-fly ash fractions of the mix control the optimum lime content yielding maximum strength. Long-term strength behaviour of steam-cured blocks has been monitored. The results indicate a favourable lime-clay ratio for stable long-term strength. A small-scale steam cured block production system has been designed and implemented to construct a load bearing masonry structure, thus demonstrating the potential of steam-cured block as a material for masonry construction.

Immunization of male rabbits with sheep luteal receptor to LH results in production of antibodies exhibiting hormone-agonistic and -antagonistic activities

Antibodies to LH/chorionic gonadotrophin receptor (LH/CG-R; molecular weight 67 000), isolated in a homogenous state (established by SDS-PAGE and ligand blotting) from sheep luteal membrane using human CG (hCG)-Sepharose affinity chromatography, were raised in three adult male rabbits (R-I, R-II and R-III). Each of the rabbits received 20-30 mu g oi the purified receptor in Freund's complete adjuvant at a time. Primary immunization was followed by booster injection at intervals. Production of receptor antibodies was monitored by (1) determining the dilution of the serum (IgG fraction) that could specifically bind 50% of I-125-LH/CG-R added and (2) analysing sera for any chance in testosterone levels. Following primary immunization and the first booster, all three rabbits exhibited a 2.5- to 6.0-fold increase in serum testosterone over basal levels and this effect was spread over a period of time (similar to 40 days) coinciding with the rise and fall of receptor antibodies. The maximal antibody titre (ED(50)) produced at this time ranged from 1:350 to 1:100 to below detectable limits for R-I, R-II and R-III respectively. Subsequent immunizations followed by the second booster resulted in a substantial increase in antibody titre (ED(50) of 1:5000) in R-I, but this was not accompanied by any change in serum testosterone over preimmune levels, suggesting that with the progress of immunization the character of the antibody produced had also changed. Two pools of antisera from R-I collected 10 days following the booster (at day 70 (bleed I) and day 290 (bleed II)) were used in further experiments. IgG isolated from bleed I but not from bleed II antiserum showed a dose-dependent stimulation of testosterone production by mouse Leydig cells in vitro, thus confirming the in vivo hormone-mimicking activity antibodies generated during the early immunization phase. The IgG fractions from both bleeds were, however, capable of inhibiting (1) I-125-hCG binding to crude sheep luteal membrane (EC(50) of 1:70 and 1:350 for bleed I and II antisera respectively) and (2) ovine LH-stimulated testosterone production by mouse Leydig cells in vitro, indicating the presence oi antagonistic antibodies irrespective of the period of time during which the rabbits were immunized. The: fact that bleed I-stimulated testosterone production could be inhibited in a dose-dependent manner by the addition of IgG from bleed II to the mouse Leydig cell in vitro assay system showed that the agonistic activity is intrinsic to the bleed I antibody. The receptor antibody (bleed II) was also capable of blocking LH action in vivo, as rabbits passively (for 24 h with LH/CG-R antiserum) as well as actively (for 130 days) immunized against LH/CG-R failed to respond to a bolus injection of LH (50 mu g). At no time, however, was the serum testosterone reduced below the basal level. This study clearly shows that, unlike with LH antibody, attempts to achieve an LH deficiency effect in vivo by resorting to immunization with hole LH receptor is difficult, as receptor antibodies exhibit both hormone-mimicking (agonistic) as well as hormone-blocking (antagonistic) activities.

Defect production due to quenching through a multicritical point

We study the generation of defects when a quantum spin system is quenched through a multicritical point by changing a parameter of the Hamiltonian as t/tau, where tau is the characteristic timescale of quenching. We argue that when a quantum system is quenched across a multicritical point, the density of defects (n) in the final state is not necessarily given by the Kibble-Zurek scaling form n similar to 1/tau(d nu)/((z nu+1)), where d is the spatial dimension, and. and z are respectively the correlation length and dynamical exponent associated with the quantum critical point. We propose a generalized scaling form of the defect density given by n similar to 1/(tau d/(2z2)), where the exponent z(2) determines the behavior of the off-diagonal term of the 2 x 2 Landau-Zener matrix at the multicritical point. This scaling is valid not only at a multicritical point but also at an ordinary critical point.

Temperature characteristics of the billet and the dies in a small batch forging production

The work reported herein is part of an on-going programme to develop a computer code which, given the geometrical, process and material parameters of the forging operation, is able to predict the die and the billet cooling/heating characteristics in forging production. The code has been experimentally validated earlier for a single forging cycle and is now validated for a small batch production. To facilitate a step-by-step development of the code, the billet deformation has so far been limited to its surface layers, a situation akin to coining. The code has been used here to study the effects of die preheat-temperature, machine speed and rate of deformation the cooling/heating of the billet and the dies over a small batch of 150 forgings. The study shows: that there is a pre-heat temperature at which the billet temperature changes little from one forging to the next; that beyond a particular number of forgings, the machine speed ceases to have any pronounced influence on the temperature characteristics of the billet; and that increasing the rate of deformation reduces the heat loss from the billet and gives the billet a stable temperature profile with respect to the number of forgings. The code, which is simple to use, is being extended to bulk-deformation problems. Given a practical range of possible machine, billet and process specifics, the code should be able to arrive at a combination of these parameters which will give the best thermal characteristics of the die-billet system. The code is also envisaged as being useful in the design of isothermal dies and processes.

Enhanced ionic conduction in dispersed solid electrolyte systems CaF2---Al2O3 and CaF2---CeO2

Dispersions of Al2O3 as well as CeO2 in CaF2 are found to enhance the conductivity of CaF2. Both these systems are biphasic and the electrical conduction in them is purely ionic in nature. At 650 K the increase in the ionic conductivity of the dispersed solid electrolyte system CaF2---Al2O3 is by about two orders of magnitude in relation to the conductivity of the host electrolyte CaF2, whereas for the CaF2---CeO2 system it is about three orders of magnitude. Some aspects of the increase in the ionic conductivities of CaF2---Al2O3 and CaF2---CeO2 electrolytes can be explained by a recent theoretical model. It is proposed that a substantial enhancement in the vacancy concentration of CaF2, brought about by the attraction of F− ions to the surface of Al2O3 (or CeO2), is responsible for the low temperature increase in the ionic conductivity of CaF2.

Production of cast aluminium-graphite particle composites using a pellet method

Copper- and nickel-coated graphite particles can be successfully introduced into aluminium-base alloy melts as pellets to produce cast aluminium-graphite particle composites. The pellets were made by pressing mixtures of nickel- or copper-coated graphite particles and aluminium powders together at pressures varying between 2 and 20 kg mm–2. These pellets were dispersed in aluminium alloy melts by plunging and holding them in the melts using a refractory coated mild steel cone, until the pellets disintegrated and the powders were dispersed. The optimum pressure for the preparation of pellets was 2 to 5 kg mm–2 and the optimum size and percentage of aluminium powder were 400 to 1000mgrm and 35 wt% respectively. Under optimum conditions the recovery of the graphite particles in the castings was as high as 96%, these particles being pushed into the last freezing interdendritic regions. The tensile strength and the hardness of the graphite aluminium alloys made using the pellet method are comparable to those of similar composites made using gas injection or the vortex method. The pellet method however has the advantage of greater reproducibility and flexibility. Dispersion of graphite particles in the matrix of cast aluminium alloys using the pellet method increases their resistance to wear.

Enhanced catharanthine and vindoline production in suspension cultures of Catharanthus roseus by ultraviolet-B light

Suspension cultures of Catharanthus roseus were used to evaluate ultraviolet-B (UV-B) treatment as an abiotic elicitor of secondary metabolites. A dispersed cell suspension culture from C. roseus leaves in late exponential phase and stationary phase were irradiated with UV-B for 5 min. The stationary phase cultures were more responsive to UV-B irradiation than late exponential phase cultures. Catharanthine and vindoline increased 3-fold and 12-fold, respectively, on treatment with a 5-min UV-B irradiation.

Quench dynamics and defect production in the Kitaev and extended Kitaev models

We study quench dynamics and defect production in the Kitaev and the extended Kitaev models. For the Kitaev model in one dimension, we show that in the limit of slow quench rate, the defect density n∼1/√τ, where 1/τ is the quench rate. We also compute the defect correlation function by providing an exact calculation of all independent nonzero spin correlation functions of the model. In two dimensions, where the quench dynamics takes the system across a critical line, we elaborate on the results of earlier work [K. Sengupta, D. Sen, and S. Mondal, Phys. Rev. Lett. 100, 077204 (2008)] to discuss the unconventional scaling of the defect density with the quench rate. In this context, we outline a general proof that for a d-dimensional quantum model, where the quench takes the system through a d−m dimensional gapless (critical) surface characterized by correlation length exponent ν and dynamical critical exponent z, the defect density n∼1/τmν/(zν+1). We also discuss the variation of the shape and spatial extent of the defect correlation function with both the rate of quench and the model parameters and compute the entropy generated during such a quenching process. Finally, we study the defect scaling law, entropy generation and defect correlation function of the two-dimensional extended Kitaev model.

The chemical ecology of seed dispersal in monoecious and dioecious figs

In the nursery pollination system of figs (Ficus, Moraceae), flower-bearing receptacles called syconia breed pollinating wasps and are units of both pollination and seed dispersal. Pollinators and mammalian seed dispersers are attracted to syconia by volatile organic compounds (VOCs). In monoecious figs, syconia produce both wasps and seeds, while in (gyno)dioecious figs, male (gall) fig trees produce wasps and female (seed) fig trees produce seeds. VOCs were collected using dynamic headspace adsorption methods on freshly collected figs from different trees using Super Q® collection traps. VOC profiles were determined using gas chromatography–mass spectrometry (GC–MS).The VOC profile of receptive and dispersal phase figs were clearly different only in the dioecious mammal-dispersed Ficus hispida but not in dioecious bird-dispersed F. exasperata and monoecious bird-dispersed F. tsjahela. The VOC profile of dispersal phase female figs was clearly different from that of male figs only in F. hispida but not in F. exasperata, as predicted from the phenology of syconium production which only in F. hispida overlaps between male and female trees. Greater difference in VOC profile in F. hispida might ensure preferential removal of seed figs by dispersal agents when gall figs are simultaneously available.The VOC profile of only mammal-dispersed female figs of F. hispida had high levels of fatty acid derivatives such as amyl-acetates and 2-heptanone, while monoterpenes, sesquiterpenes and shikimic acid derivatives were predominant in the other syconial types. A bird- and mammal-repellent compound methyl anthranilate occurred only in gall figs of both dioecious species, as expected, since gall figs containing wasp pollinators should not be consumed by dispersal agents.

Translational fusion of two beta-subunits of human chorionic gonadotropin results in production of a novel antagonist of

The strategy of translationally fusing the alpha-and beta-subunits of human chorionic gonadotropin (hCG) into a single-chain molecule has been used to produce novel analogs of hCG. Previously we reported expression of a biologically active singlechain analog hCG alpha beta expressed using Pichia expression system. Using the same expression system, another analog, in which the alpha-subunit was replaced with the second beta-subunit, was expressed (hCG beta beta) and purified. hCG beta beta could bind to LH receptor with an affinity three times lower than that of hCG but failed to elicit any response. However, it could inhibit response to the hormone in vitro in a dose- dependent manner. Furthermore, it inhibited response to hCG in vivo indicating the antagonistic nature of the analog. However, it was unable inhibit human FSH binding or response to human FSH, indicating the specificity of the effect. Characterization of hCG alpha beta and hCG beta beta using immunological tools showed alterations in the conformation of some of the epitopes, whereas others were unaltered. Unlike hCG, hCG beta beta interacts with two LH receptor molecules. These studies demonstrate that the presence of the second beta-subunit in the single-chain molecule generated a structure that can be recognized by the receptor. However, due to the absence of alpha-subunit, the molecule is unable to elicit response. The strategy of fusing two beta-subunits of glycoprotein hormones can be used to produce antagonists of these hormones.

Cloning by genomic PCR and production of peanut agglutinin in Escherichia coli

Using the polymerase chain reaction, the coding sequence for peanut agglutinin (PNA) was cloned and expressed in Escherichia coli. Amplified PNA is identical to previously reported cDNA, suggesting the absence of any introns in PNA gene. Recombinant (re-) PNA forms inclusion bodies in E. coli. Production of PNA was confirmed by probing Western blots with polyclonal anti-PNA immunoglobulin G. Inclusion bodies were solubilized with 6 M guanidine-HCl and renatured by rapid dilution in the presence of metal ions. The renatured lectin was then purified by affinity chromatography. The re-lectin shows carbohydrate-binding properties similar to the natural PNA. This expression system provides a model for future mutagenesis studies of the carbohydrate-binding site and thus facilitates ongoing efforts to explore the molecular basis for the specificity of lectin-carbohydrate interaction.

Phase relations and thermodynamic properties of compounds in the pseudobinary system BaO-Y2O3

The coexisting phases in the pseudobinary system BaO-Y2O3 have been identified by equilibrating samples containing different amounts of component oxides at 1173, 1273 and 1373 K. Only two ternary oxides, BaY2O4 and Ba3Y4O9, have been found to be stable in the temperature range of investigation. Solid state galvanic cells: Pt, O2+BaO+BaF2double vertical barBaF2+2mol%Al2O3double vertical barBaF2+BaY2O4+Y2O3+O2, Pt and Pt, O2+BaO+BaF2double vertical barBaF2+2mol% Al2O3double vertical barBaF2+BaY2O4+Ba3Y4O9+O2, Pt have been employed for determining the Gibbs' energies of formation of BaY2O4 and Ba3Y4O9 from the component oxides in the range 850 to 1250 K. A composite solid electrolyte incorporating Al2O3-dispersed BaF2 was used in the cells. To prevent interaction between the Al2O3 powder and electrode materials, the solid electrolyte was coated with pure BaF2. The Gibbs' energies of formation of BaY2O4 and Ba3Y4O9 from component oxides are given by: Δf0 (BaY2O4, s)=−128,310+5.211T (±580) J mol−1, (850less-than-or-equals, slantTless-than-or-equals, slant1250 K) and ΔGfo(Ba3Y4O9, s)= −317,490 −24.704T (±1100) J mol−1, (850less-than-or-equals, slantTless-than-or-equals, slant1250 K).

Application of an evolutionary fuzzy system for the estimation of workforce deployment and cross-training in an assembly environment

Owing to the increased customer demands for make-to-order products and smaller product life-cycles, today assembly lines are designed to ensure a quick switch-over from one product model to another for companies' survival in market place. The complexity associated with the decisions pertaining to the type of training and number of workers and their exposition to the different tasks especially in the current era of customized production is a serious problem that the managers and the HRD gurus are facing in industry. This paper aims to determine the amount of cross-training and dynamic deployment policy caused by workforce flexibility for a make-to-order assembly. The aforementioned issues have been dealt with by adopting the concept of evolutionary fuzzy system because of the linguistic nature of the attributes associated with product variety and task complexity. A fuzzy system-based methodology is proposed to determine the amount of cross-training and dynamic deployment policy. The proposed methodology is tested on 10 sample products of varying complexities and the results obtained are in line with the conclusions drawn by previous researchers.

Geographic Resources Decision Support System – an Open Source GIS

Fully structured and matured open source spatial and temporal analysis technology seems to be the official carrier of the future for planning of the natural resources especially in the developing nations. This technology has gained enormous momentum because of technical superiority, affordability and ability to join expertise from all sections of the society. Sustainable development of a region depends on the integrated planning approaches adopted in decision making which requires timely and accurate spatial data. With the increased developmental programmes, the need for appropriate decision support system has increased in order to analyse and visualise the decisions associated with spatial and temporal aspects of natural resources. In this regard Geographic Information System (GIS) along with remote sensing data support the applications that involve spatial and temporal analysis on digital thematic maps and the remotely sensed images. Open source GIS would help in wide scale applications involving decisions at various hierarchical levels (for example from village panchayat to planning commission) on economic viability, social acceptance apart from technical feasibility. GRASS (Geographic Resources Analysis Support System, http://wgbis.ces.iisc.ernet.in/grass) is an open source GIS that works on Linux platform (freeware), but most of the applications are in command line argument, necessitating a user friendly and cost effective graphical user interface (GUI). Keeping these aspects in mind, Geographic Resources Decision Support System (GRDSS) has been developed with functionality such as raster, topological vector, image processing, statistical analysis, geographical analysis, graphics production, etc. This operates through a GUI developed in Tcltk (Tool command language / Tool kit) under Linux as well as with a shell in X-Windows. GRDSS include options such as Import /Export of different data formats, Display, Digital Image processing, Map editing, Raster Analysis, Vector Analysis, Point Analysis, Spatial Query, which are required for regional planning such as watershed Analysis, Landscape Analysis etc. This is customised to Indian context with an option to extract individual band from the IRS (Indian Remote Sensing Satellites) data, which is in BIL (Band Interleaved by Lines) format. The integration of PostgreSQL (a freeware) in GRDSS aids as an efficient database management system.

A GIS (geographical information system)-based spatial data mining approach for optimal location and capacity planning of distributed biomass power generation facilities: A case study of Tumkur district, India

This paper primarily intends to develop a GIS (geographical information system)-based data mining approach for optimally selecting the locations and determining installed capacities for setting up distributed biomass power generation systems in the context of decentralized energy planning for rural regions. The optimal locations within a cluster of villages are obtained by matching the installed capacity needed with the demand for power, minimizing the cost of transportation of biomass from dispersed sources to power generation system, and cost of distribution of electricity from the power generation system to demand centers or villages. The methodology was validated by using it for developing an optimal plan for implementing distributed biomass-based power systems for meeting the rural electricity needs of Tumkur district in India consisting of 2700 villages. The approach uses a k-medoid clustering algorithm to divide the total region into clusters of villages and locate biomass power generation systems at the medoids. The optimal value of k is determined iteratively by running the algorithm for the entire search space for different values of k along with demand-supply matching constraints. The optimal value of the k is chosen such that it minimizes the total cost of system installation, costs of transportation of biomass, and transmission and distribution. A smaller region, consisting of 293 villages was selected to study the sensitivity of the results to varying demand and supply parameters. The results of clustering are represented on a GIS map for the region.