Controlled photoluminescence from self-assembled semiconductor-metal quantum dot hybrid array films

Thin films of hybrid arrays of cadmium selenide quantum dots and polymer grafted gold nanoparticles have been prepared using a BCP template. Controlling the dispersion and location of the respective nanoparticles allows us to tune the exciton-plasmon interaction in such hybrid arrays and hence control their optical properties. The observed photoluminescence of the hybrid array films is interpreted in terms of the dispersion and location of the gold nanoparticles and quantum dots in the block copolymer matrix.

Ionic conductivity and dielectric measurements in single crystal β---AgI

Ionic conductivity measurements have been made on pure, copper-doped and cadmium-doped single crystals. Dielectric measurements in the frequency range 30Hz–100Hz showed that there was no anomalously to be (0.64 ± 0.02) eV and migration energies for silver ion intersitials and vacancies in the c direction to be (0.41 ± 0.02) eV and (0.50 ± 0.02) eV respectively. ESR measurements have shown that copper exists as Cu+ in these crystals. Dielectric measurements in the frequency range (OHz–100KHz showed that there was no anomalously high value for ε as reported earlier.

Photoconductivity in β-AgI

Excitation spectra and transient and steady-state photoconductivity have been studied in undoped and 0.8-mole% Cu-doped single-crystal β-AgI between 150 and 260°K. A single peak in the spectral response was found to occur in each case, at 2.88 eV for undoped and at 2.81 eV for copper-doped specimens at 260 K, the difference being due to a decrease in band gap. The anisotropy due to polarization of incident radiation parallel or perpendicular to the c direction, which is a measure of the energy difference between the Γ9 and Γ7 levels in the valence band, was found to be 0.010 eV. Transient-photoconductivity experiments showed that the hole lifetime was 6 μ sec at 300°K, an order of magnitude larger than the electron lifetime. The hole drift mobility was found to be 12±2 cm2/ V sec at 300°K and limited by traps at a depth of 0.51±0.01 eV with concentration (3-5)×109/cm3 and capture cross section 10-11 cm2. The study of photoconductivity decay versus temperature revealed the presence of shallow hole traps at 0.14±0.02 eV with concentration greater than 1016/cm3 and capture cross section 10-19 cm2. The steady-state photoconductivity was determined by the deep hole traps at 0.51 eV, and showed the presence of shallow electron traps at a depth of 0.28 eV. The trap distribution was found to be substantially the same in pure and copper-doped specimens, indicating the monovalent substitutional role of copper. The effects of iodine annealing, cadmium doping, and heating above the transition temperature were also studied. The possible nature of the traps is discussed.

Thermodynamics of Phosphorus and Sulphur Removal during Basic Oxygen Steelmaking

Removal of impurity elements from hot metal is essential in basic oxygen steelmaking. Oxidation of phosphorus from hot metal has been studied by several authors since the early days of steelmaking. Influence of different parameters on the distribution of phosphorus, seen during the recent work of the authors, differs somewhat from that reported earlier. On the other hand, removal of sulphur during steelmaking has drawn much less attention. This may be due to the magnitude of desulphurisation in oxygen steelmaking being relatively low and desulphurisation during hot metal pre-treatment or in the ladle furnace offering better commercial viability Further, it is normally accepted that sulphur is removed to steelmaking slag in the form of sulphide only However, recent investigations have indicated that a significant amount of sulphur removed during basic oxygen steelmaking can exist in the form of sulphate in the slag under oxidising conditions. The distribution of sulphur during steelmaking becomes more important in the event of carry-over of sulphur-rich blast-furnace slag, which increases sulphur load in the BOF. The chemical nature of sulphur in this slag undergoes a gradual transition from sulphide to sulphate as the oxidative refining progresses.

Selective Flotation of Molybdenite and Chalcopyrite

Separation of molybdenite from chalcopyrite from the bulk concentrate of a low grade molybdenite ore from Chintamani, Kolar District, Karnataka, has been attempted in a modified Hallimond tube microflotation set-up. The flotation parameters studied are, sodium sulphide and potassium cyanide as depressants for chalcopyrite, pH, depressant concentration, steaming time and time of flotation. Selectivity index was used as a separation parameter. Steaming for 25 min followed by flotation for 7 min at 80 mg/l concentration of potassium cyanide and pH 9 gave the best results for separation of molybdenite. 19 ref.--AA

Laboratory studies on ball wear in the grinding of a hematite-magnetite ore

Marked-ball grinding tests were carried out under different grinding conditions and environments. Three types of balls were used, namely, cast hyper steel, high chrome cast iron and EN-31 (forged), which cover a wide range of chemical composition, microstructure and media hardness. The effect of pulp density on ball wear and grinding efficiency was also studied. Relative pulp viscosities at different percent solids for the ore slurry were also determined. As the Kudremukh ore contained about 0.2% pyrite, the effect of addition of pyrite on ball wear was studied separately. Results of marked-ball grinding tests indicated that ball wear increased with time and showed a sharp increase for wet grinding over dry grinding. Ball wear under wet grinding conditions was also influenced by the gaseous atmosphere in the mill. At 70% solids, the best results in terms of reduced ball wear coupled with satisfactory grinding efficiency were obtained. The influence of oxygen on the corrosive wear of grinding balls was increasingly felt only if sulphide minerals such as pyrite were also present in the ore. The various ball materials could be arranged in the following order with respect to their overall wear resistance: high chrome cast iron > EN-31 (forged) > cast hyper steel.Possible ball wear mechanisms involved in the grinding of Kudremukh ore are discussed.

General model of a foam bed reactor

A general model of a foam bed reactor has been developed which rigorously accounts for the extent of gas absorption with chemical reaction occurring in both the storage and foam sections. Its applicability extends to a wide spectrum of reaction velocities. The possibilities of the predominance of the bulk-liquid reaction in the storage section or the absorption with reaction in the foam section can be handled as merely special cases of the general analysis. The importance of foam for carrying out a particular gas-liquid reaction is characterised by a criterion in terms of the fractional rate of reaction in the foam section. Trends of variations in the concentrations of dissolved free A, solute B, and gas-phase A with time of operation of the reactor are presented. The nature of the variation in the fractional rate of reaction in the foam section with time, at different reaction velocities, and the effect of the liquid flow rate (across the storage section) on the transience are also illustrated. Finally, the predictions of the general model have been validated using the available experimental data on the oxidation of sodium sulphide in a foam bed reactor. The agreement between the experimental and the present theoretical information is fairly good, apart from being more insightful than all the previous models of this reactor.

Casting and heat treatment variables of Al–7Si–Mg alloy

A review of the research work that has been carried out thus far relating the casting and heat treatment variables to the structure and mechanical properties of Al–7Si–Mg (wt-%) is presented here. Although specifications recommend a wide range of magnesium contents and a fairly high content of iron, a narrow range of magnesium contents, closer to either the upper or lower specified limits depending on the properties desired, and a low iron content will have to be maintained to obtain optimum and consistent mechanical properties. A few studies have revealed that the modification of eutectic silicon slightly increases ductility and fracture toughness and also that the effect of modification is predominant at low iron content. Generally, higher solidification rates give superior mechanical properties. Delayed aging (the time elapsed between quenching and artificial aging during precipitation hardening) severely affects the strength of the alloy. The mechanism of delayed aging can be explained on the basis of Pashley's kinetic model. It has been reported that certain trace additions (cadmium, indium, tin, etc.) neutralise the detrimental effect of delayed aging. In particular, it should be noted that delayed aging is not mentioned in any of the specifications. With reference to the mechanism by which trace additions neutralise the detrimental effect of delayed aging, various hypotheses have been postulated, of which impurity–vacancy interaction appears to be the most widely accepted.

Ball wear mechanisms and control in the grinding of sulfide and phosphate ores

Marked ball grinding tests were carried out in the laboratory using high carbon low alloy steel (cast and forged) and high chrome cast iron balls. Relative ball wear as a function of grinding period and milling conditions was evaluated for the different type of ball materials in the grinding of lead-zinc sulphide and phosphate ores. Results indicated that ball wear increased with time and showed a sharp increase for wet grinding over dry grinding. Ball wear under wet grinding conditions was also influenced by the gaseous atmosphere in the mill. The influence of oxygen on the corrosive wear of grinding balls was increasingly felt in case of sulphide ore grinding. The grinding ball materials could be arranged in the following order with respect to their overall wear resistance:

Influence of deviation from stoichiometry on the photoluminescence in CdTe doped with indium

Low temperature photoluminescence of vacuum and cadmium annealed CdTe:In is reported here. A new peak at similar to 1.14 eV related to transitions from the conduction band to an acceptor involving a tellurium vacancy has been observed.

Ultrasonic spray pyrolysis of CZTS solar cell absorber layers and characterization studies

CZTS (Copper Zinc Tin Sulphide) is a wide band gap quartnery chalcopyrite which has a band gap of about 1.45 eV and an absorption coefficient of 10(4) cm(-1); thus making it an ideal material to be used as an absorber layer in solar cells. Ultrasonic Spray Pyrolysis is a deposition technique, where the solution is atomized ultrasonically, thereby giving a fine mist having a narrow size distribution which can be used for uniform coatings on substrates. An Ultrasonic Spray Pyrolysis equipment was developed and CZTS absorber layers were successfully grown with this technique on soda lime glass substrates using aqueous solutions. Substrate temperatures ranging from 523 K to 723 K were used to deposit the CZTS layers and these films were characterized using SEM, EDAX and XRD. It was observed that the film crystallized in the kesterite structure and the best crystallites were obtained at 613 K. It was observed that the grain size progressively increased with temperature. The optical band gap of the material was obtained as 1.54 eV.

Growth and development of Thiobacillus ferrooxidans for engineering applications

A bioprocessing approach for the extraction of base, nuclear and precious metals from refractory and lean grade ores has been reviewed in this paper. Characteristic morphological features of Thiobacillus ferrooxidans, the organism which has been extensively used for biooxidation of sulphide ores have been discussed. Mechanisms of chemoautotrophy and mineral oxidation have been illustrated. The current engineering applications of this microorganism have also been brought out. Various methods for accelerating the growth of Thiobacillus ferrooxidans for faster biooxidation and genetic manipulation for development of desired strains have been outlined.

Advances in storage batteries

Over the years, new power requirements for telecommunication, space, automotive and traction applications have arisen which need to be met. Although lead-acid and nickel-cadmium storage batteries continue to be the work horses with limited advances, associated environmental hazards and recycling are still the issues to be resolved. As a result, lead-acid and nickel-cadmium storage batteries have declined in importance whilst nickel-metal hydride and lithium secondary batteries with superior performances have shown greater acceptability in newer applications. These developments are reflected in this article.

Studies on multi-metal ion tolerance of Thiobacillus ferrooxidans

The influence of different concentrations of base metal ions, such as CU2+, Zn2+ and Fe3+, when present either alone or in different possible binary and ternary combinations in a 9K medium, on the fel rous ion oxidation ability of Thiobacillus ferrooxidans was studied. Levels and degree of toxicity of these ions have been quantified in terms of toxicity index (TI). Copper and zinc tolerant strains of the bacteria were developed through serial subculturing and their activity tested in the presence of the above metal ions in comparison with the behavior of wild unadapted cells under similar conditions. Copper tolerant strains (25 g/L Cu2+) were found to be more efficient in the bioleaching of both copper and zinc concentrates than wild unadapted strains, while zinc tolerant strains (40 g/L Zn2+) exhibited better leaching efficiency only in the bioleaching of sphalerite concentrates. The significance and relevance of multi-metal ion tolerance in Thiobacillus ferrooxidans has been highlighted with respect to bioleaching of sulphide mineral concentrates. (C) 1997 Published by Elsevier Science Ltd.

Crystal structure of nonadentate tricompartmental ligand derived from pyridine-2,6-dicarboxylic acid: Spectroscopic, electrochemical and thermal investigations of its transition metal(II) complexes

The coordinating behavior of a new dihydrazone ligand, 2,6-bis(3-methoxysalicylidene) hydrazinocarbonyl]pyridine towards manganese(II), cobalt(II), nickel(II), copper(II), zinc(II) and cadmium(II) has been described. The metal complexes were characterized by magnetic moments, conductivity measurements, spectral (IR, NMR, UV-Vis, FAB-Mass and EPR) and thermal studies. The ligand crystallizes in triclinic system, space group P-1, with alpha=98.491(10)degrees, beta=110.820(10)degrees and gamma=92.228(10)degrees. The cell dimensions are a=10.196(7)angstrom, b=10.814(7)angstrom, c=10.017(7)angstrom, Z=2 and V=1117.4(12). IR spectral studies reveal the nonadentate behavior of the ligand. All the complexes are neutral in nature and possess six-coordinate geometry around each metal center. The X-band EPR spectra of copper(II) complex at both room temperature and liquid nitrogen temperature showed unresolved broad signals with g(iso) = 2.106. Cyclic voltametric studies of copper(II) complex at different scan rates reveal that all the reaction occurring are irreversible. (C) 2011 Elsevier B.V. All rights reserved.