A theory on the migration of an extraneous electron across hydrogen bonds in polypeptides

The migrating electrons in biological systems normally are extraneous and taking this into account the electron delocalisation across the hydrogen bonds in proteins is re-examined. It is seen that an extraneous electron can travel rapidly via the low-lying virtual orbitals of the hydrogen-bonded π-electronic structure of peptide units in proteins. The frequency of electron transfer decreases slowly with an increase in the path length. However, the coupling of electron and protonic motions enhances this frequency. Transfer of electrons across the hydrogen bonds in accordance with the double-exchange mechanism does not appear to be possible. This theory offers a possibility for an extraneous electron to transfer within protein structures.

Impedance parameters and the state-of-charge. III. Zinc-manganese dioxide and magnesium-manganese dioxide dry batteries

The problem of non-destructive determination of the state-of-charge of zinc- and magnesium-manganese dioxide dry batteries is examined experimentally from the viewpoint of internal impedance and open-circuit voltage at equilibrium. It is shown that the impedance is mainly charge-transfer controlled at relatively high states-of-charge and progressively changes over to diffusion control as the state-of-charge decreases in the case of zinc-manganese dioxide dry batteries. On the other hand, the impedance is mainly diffusion controlled for undischarged batteries but becomes charge-transfer controlled as soon as there is some discharge in the case of magnesium-manganese dioxide batteries. It is concluded that the determination of state-of-charge is not possible for both types of batteries by the measurement of impedance parameters due to film-induced fluctuations of these parameters. The measurement of open-circuit voltage at equilibrium can be used as a state-of-charge indicator for Zn-MnO2 batteries but not for Mg-MnO2 batteries.

Impedance parameters and the state-of-charge. II. Lead-acid battery

The determination of the state-of-charge of the lead-acid battery has been examined from the viewpoint of internal impedance. It is shown that the impedance is controlled by charge transfer and to a smaller extent by diffusion processes in the frequency range 15–100 Hz. The equivalent series/parallel capacitance as well as the a.c. phase-shift show a parabolic dependence upon the state-of-charge, with a maximum or minimum at 50% charge. These results are explained on the basis of a uniform transmission-line analog equivalent circuit for the battery electrodes.

Electronic excitations and alternation of conjugated polymers

The electronic excitations and fluorescence of conjugated polymers are related to large or small alternation ? of the transfer integrals t(1 ± ?) along the backbone. The fluorescence of polysilanes (PSs) and poly (para-phenylenevinylene (PPV) is linked to large ?, which places the one-photon gap Eg below the lowest two-photon gap Ea and reduces distortions due to electron-phonon (e-p) coupling. In contrast to small ? not, vert, similar 0.1 in ?-conjugated polymers, such as polyacetylene (PA), para-conjugated phenyls lead to an extended ?-system with increased alternation, to states localized on each ring and to charge-transfer excitations between them. Surprisingly good agreement is found between semiempirical parametric method 3 (PM3) bond lengths and exact Pariser-Parr-Pople (PPP) ?-bond orders for trans-stilbene, where the PPV bipolarons are confined to two phenyls. Stilbene spectra are consistent with increased alternation and small e-p distortions.

Electronic structure of La1-xSrxFeO3

We have investigated the electronic structure of well-characterized samples of La1-xSrxFeO3 (x=0.0�0.4) by x-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy, bremsstrahlung isochromat (BI) spectroscopy, and Auger electron spectroscopy. We find systematic behavior in the occupied and unoccupied density of states reflecting changes in the electronic structure on hole doping via Sr substitution as well as providing estimates for different interaction strengths. The spectral features, particularly of the unoccupied states obtained from BI spectra, indicate the probable reason for the absence of an insulator-metal transition in this series. Analysis of the Auger spectra provides the estimates of the on-site effective Coulomb interaction strengths in Fe 3d and O 2p states. The parameter values for the bare charge-transfer energy ? and the Fe 3d�O 2p hybridization strength t? for LaFeO3 are obtained from an analysis of the Fe 2p core-level XPS in terms of a model many-body calculation. We discuss the character of the ground state in LaFeO3 as well as the nature of the doped hole states in La1-xSrxFeO3, based on these parameter values.

Folding of a Donor-Containing Ionene by Intercalation with an Acceptor

Cationic ionenes that bear electron-rich 1,5-dialkoxynaphthalene (DAN) units within the alkylene segment were allowed to interact with different types of electron-deficient, acceptor-containing molecules in an effort to realize intercalation-induced folding of the ionenes; the collapse of the chains was expected to occur in such a way that the donor and acceptor units become arranged in an alternating fashion. Several acceptor-bearing molecules were prepared by the derivatization of pyromellitic dianhydride and naphthalene tetracarboxylic dianhydride with two different oligoethylene glycol monomethyl ether monoamines. This yielded acceptor molecules with different water solubility and allowed the examination of solvophobic effects in the folding process. UV/Vis spectroscopic studies were carried out by using a 1:1 mixture of the DAN-ionenes and different acceptor molecules in water/DMSO solvent mixtures. The intensity of the charge-transfer (CT) band was seen to increase with the water content in the solvent mixture, thereby suggesting that the intercalation is indeed aided by solvophobic effects. The naphthalene diimide (NDI) bearing acceptor molecules consistently formed significantly stronger CT complexes when compared to the pyromellitic diimide (PDI) bearing acceptor molecules, which is a reflection of the stronger pi-stacking tendency of the former. AFM studies of drop-cast films of different ionene-acceptor combinations revealed that compact folded structures are formed most effectively under conditions in which the strongest CT complex is formed.

Synergitic Promotion of Electrooxidation of Methanol of Carbon-Supported PT-SN Catalysts

Electrooxidation of methanol in sulphuric acid on carbon-supported electrodes containing Pt-Sn bimetal catalysts prepared by an in-situ route is reported, The catalysts have been characterized employing chemical analyses, XRD, and XANES data in conjunction with electrochemistry. This study suggests that the Sn content in Pt-Sn bimetals produces: (i) a charge transfer from Sn to Pt and (ii) an increase in the coverage of adsorbed methanolic residues with the Sn content. From the electrode-kinetics data, it is inferred that while the electrodes of (3:3) Pt-Sn/C catalyst involve a 2-electron rate-limiting step akin to Pt/C electrodes, it is shifted to only 1-electron on (3:2) Pt-Sn/C, (3:3) Pt-Sn/C, and (3:4) Pt-Sn/C electrodes.

Modified-Pore-Filled-PVDF-Membrane Electrolytes for Direct Methanol Fuel Cells

The polyvinylidene fluoride (PVDF) membrane is modified by the chemical etchant-route employing a sodium naphthalene charge-transfer complex followed by impregnation with Nafion ionomer or polyvinyl alcohol (PVA)-polystyrene sulfonic acid (PSSA) polymeric blend solutions by a dip-coating technique to form pore-filled-membrane electrolytes for application in direct methanol fuel cells (DMFCs). The number of coatings on the surface-modified PVDF membrane is varied between 5 and 15 and is found to be optimum at 10 layers both for Nafion and PVA-PSSA impregnations for effective DMFC performance. Hydrophilicity of the modified-membrane electrolytes is studied by determining average contact angle and surface-wetting energy. Morphology of the membranes is analyzed by a cross-sectional scanning electron microscope. The modified PVDF membrane electrolytes are characterized for their water-methanol sorption in conjunction with their mechanical properties, proton conductivity, and DMFC performance. Air permeability for the modified membranes is studied by a capillary-flow porometer. Methanol crossover flux across modified-PVDF-membrane electrolytes is studied by measuring the mass balance of methanol using a density meter. DMFCs employing membrane electrode assemblies with the modified PVDF membranes exhibit a peak power-density of 83 mW/cm(2) with Nafion impregnation and 59 mW/cm(2) for PVA-PSSA impregnation, respectively. Among the membranes studied here, stabilities of modified-pore-filled PVDF-Nafion and PVDF-PVA-PSSA membranes with 10-layers coat are promising for application in DMFCs. (C) 2010 The Electrochemical Society. DOI: 10.1149/1.3518774] All rights reserved.

Coordination-Driven Self-Assembly of M3L2 Trigonal Cages from Preorganized Metalloligands Incorporating Octahedral Metal Centers and Fluorescent Detection of Nitroaromatics

The design and preparation of novel M3L2 trigonal cages via the coordination-driven self-assembly of preorganized metalloligands containing octahedral aluminum(III), gallium(III), or ruthenium(II) centers is described. When tritopic or dinuclear linear metalloligands and appropriate complementary subunits are employed, M3L2 trigonal-bipyramidal and trigonal-prismatic cages are self-assembled under mild conditions. These three-dimensional cages were characterized with multinuclear NMR spectroscopy (H-1 and P-31) and high-resolution electrospray ionization mass spectrometry. The structure of one such trigonal-prismatic cage, self-assembled from an arene ruthenium metalloligand, was confirmed via single-crystal X-ray crystallography. The fluorescent nature of these prisms, due to the presence of their electron-rich ethynyl functionalities, prompted photophysical studies, which revealed that electron-deficient nitroaromatics are effective quenchers of the cages' emission. Excited-state charge transfer from the prisms to the nitroaromatic substrates can be used as the basis for the development of selective and discriminatory turn-off fluorescent sensors for nitroaromatics.

Synthesis, characterization and photoluminescence properties of CaSiO3: Eu3+ red phosphor

CaSiO3:Eu3+ (1-5 mol%) red emitting phosphors have been synthesized by a low-temperature solution combustion method. The phosphors have been well characterized by powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and optical spectroscopy. PXRD patterns reveal monoclinic CaSiO3 phase can be obtained at 900 degrees C. The SEM micrographs show the crystallites with irregular shape, mostly angular. Upon 254 nm excitation, the phosphor show characteristic fluorescence D-5(0) -> F-7(J) (J = 0, 1, 2, 3, 4) of the Eu3+ ions. The electronic transition located at 614 nm corresponding to D-5(0) -> F-7(2) of Eu3+ ions, which is stronger than the magnetic dipole transition located at 593 nm corresponding to D-5(0) -> F-7(1) of Eu3+ ions. Different pathways involved in emission process have been studied. Concentration quenching has been observed for Eu3+ concentration >4 mol%. UV-visible absorption shows an intense band at 240 nm in undoped and 270 nm in Eu3+ doped CaSiO3 which is attributed to oxygen to silicon (O-Si) ligand-to-metal charge-transfer (LMCT) band in the SiO32- group. The optical energy band gap is widened with increase of Eu3+ ion dopant. (C) 2010 Elsevier B.V. All rights reserved.

Methanol oxidation on carbon-supported platinum-tin electrodes in sulfuric acid

A study is made of the electrooxidation of methanol in sulfuric acid on carbon-supported electrodes containing platinum-tin bimetal catalysts that are prepared by an in situ potentiometric-characterization route. The catalysts are investigated by employing chemical analyses, X-ray diffraction (XRD), X-ray absorption-near-edge spectroscopy (XANES) and X-ray photoelectron spectroscopy (XPS) data in conjunction with electrochemical measurements. From the electrochemical data, it is inferred that while an electrode with (3:1) Pt-Sn/C catalyst involves a two-electron rate-limiting step akin to platinum-on-carbon electrodes, it is shifted to a one-electron mechanism on electrodes with (3:2)Pt-Sn/C, (3:3)Pt-Sn/C, and (3:4)Pt-Sn/C catalysts. The study suggests that the tin content in the platinum-tin bimetal catalyst produces: (i) a charge transfer from tin to platinum; (ii) an increase in the coverage of adsorbed methanolic residues with increase in the tin content, as indicated by the shift in rest potential of the electrodes towards the reversible value for oxidation of methanol (0.043 V versus SHE), and (iii) a decrease in the overall content of higher valent platinum sites in the catalyst.

Methanol oxidation on carbon-supported platinum-tin electrodes in sulfuric acid

A study is made of the electrooxidation of methanol in sulfuric acid on carbon-supported electrodes containing platinum-tin bimetal catalysts that are prepared by an in situ potentiometric-characterization route. The catalysts are investigated by employing chemical analyses, X-ray diffraction (XRD), X-ray absorption-near-edge spectroscopy (XANES) and X-ray photoelectron spectroscopy (XPS) data in conjunction with electrochemical measurements. From the electrochemical data, it is inferred that while an electrode with (3:1) Pt-Sn/C catalyst involves a two-electron rate-limiting step akin to platinum-on-carbon electrodes, it is shifted to a one-electron mechanism on electrodes with (3:2)Pt-Sn/C, (3:3)Pt-Sn/C, and (3:4)Pt-Sn/C catalysts. The study suggests that the tin content in the platinum-tin bimetal catalyst produces: (i) a charge transfer from tin to platinum; (ii) an increase in the coverage of adsorbed methanolic residues with increase in the tin content, as indicated by the shift in rest potential of the electrodes towards the reversible value for oxidation of methanol (0.043 V versus SHE), and (iii) a decrease in the overall content of higher valent platinum sites in the catalyst.

Inter And Intramolecular Interactions Of Porphyrins With 5,5′-Dithiobis(2-Nitrobenzoic Acid)

meso-Tetraphenylporphyrin and its metal [zinc(II) and copper(II)] derivatives form both inter and intramolecular complexes with 5,5′-dithiobis(2-nitrobenzoic acid) (DTNB). The nature of interaction is predominantly charge transfer (CT) in origin, with the porphyrin functioning as a II-donor and DTNB as an acceptor. Among the covalently linked intramolecular systems, the magnitude of CT interaction varies with the position (of one of the aryl groups of the porphyrin) to which DTNB is attached as ortho meta > para. Steady-state and time-resolved fluorescence studies revealed electron transfer to be the dominant pathway for the fluorescence quenching in these systems. Steady-state photolysis experiments probed using EPR and optical absorption studies have shown that electron transfer (from the excited singlet state of the porphyrin) to DTNB results in the formation of thiyl radical and production of free thiolate anion. It is found that the products of electrochemical reduction of covalently linked porphyrin-DTNB systems are different from those observed for the photochemical studies.

Electronic structure of early 3d-transition-metal oxides by analysis of the 2p core-level photoemission spectra

The electronic structures of a wide range of early transition-metal (TM) compounds, including Ti and V oxides with metal valences ranging from 2+ to 5+ and formal d-electron numbers ranging from 0 to 2, have been investigated by a configuration-interaction cluster model analysis of the core-level metal 2p x-ray photoemission spectra (XPS). Inelastic energy-loss backgrounds calculated from experimentally measured electron-energy-loss spectra (EELS) were subtracted from the XPS spectra to remove extrinsic loss features. Parameter values deduced for the charge-transfer energy Delta and the d-d Coulomb repulsion energy U are shown to continue the systematic trends established previously for the late TM compounds, giving support to a charge-transfer mechanism for the satellite structures. The early TM compounds are characterized by a large metal d-ligand p hybridization energy, resulting in strong covalency in these compounds. Values for Delta and U suggest that many early TM compounds should be reclassified as intermediate between the charge-transfer regime and the Mott-Hubbard regime.

Evidence for correlation effects in Sr2RuO4 from resonant and x-ray photoemission spectroscopy

We study the electronic structure of Sr2RuO4, a noncuprate layered superconductor (T-c=0.93 K), using electron spectroscopy. X-ray photoemission spectroscopy shows that the single particle occupied density of states (DOS) is in fair agreement with the calculated DOS. However, resonant photoemission spectroscopy across the Ru 4p-4d threshold establishes the existence of a correlation satellite to the Ru 4d band. The results indicate substantial charge-transfer character at the Fermi level, with on-site correlations U-dd comparable in magnitude to the Ru-O hopping integral, like the cuprates.