Observations on the role of the steel disc counterface during the sliding of various structural ceramics

Sliding wear characteristics and mechanisms of structural ceramics, namely Al2O3, zirconia-toughened alumina, tetragonal zirconia polycrystals (TZP) and Si3N4 against a steel counterface are influenced by mechanical and tribochemical interactions, specific to the combinations studied. The present paper studies the role of the disc in the sliding wear process of the above ceramics. Experiments were conducted at a pressure of 15.5 MPa between 0.1 and 12.0 m s(-1) with ceramic pins sliding against an EN-24 steel disc. Except in the case of TZP, the disc morphology is sensitive to variations in speed rather than to the pin material. The disc track is (i) mildly abraded at low speeds (about 0.1-0.75 m s(-1)), (ii) severely abraded at intermediate speeds (about 1.0-3.0 m s(-1)), (iii) covered with black patches at high speeds (about 4.0-6.0 m s(-1)) and (iv) completely black at very high speeds (about 7.0-12.0 m s(-1)). In the case of TZP, although black patches appear, transfer of TZP onto the disc surface and high wear of TZP occurs at 4.0 m s(-1). The order of the wear of the disc estimated from profilometric measurements is the same for all the ceramics. Except for Si3N4, the onset of wear of the ceramics is associated with the appearance of deep 'V' grooves on either side of the profile of the disc track. This can be explained on the basis of the thermal and hardness variations. Although other interaction products specific to the ceramic pin are present, the formation of iron oxides dominates the wear of the disc.

Hydrothermal synthesis, characterization and Raman studies of Eu3+ activated Gd2O3 nanorods

Eu3+ (8 mol%) activated gadolinium oxide nanorods have been prepared by hydrothermal method without and with surfactant, cityl trimethyl ammonium bromide (CTAB). Powder X-ray diffraction (PXRD) studies reveal that the as-formed product is in hexagonal Gd(OH)(3):Eu phase and subsequent heat treatment at 350 and 600 degrees C transforms the sample to monoclinic GdOOH:Eu and cubic Gd2O3:Eu phases, respectively. The structural data and refinement parameters for cubic Gd2O3:Eu nanorods were calculated by the Rietveld refinement. SEM and TEM micrographs show that as-obtained Gd(OH)(3):Eu consists of uniform nanorods in high yield with uniform diameters of about 15 nm and lengths of about 50-150 nm. The temperature dependent morphological evolution of Gd2O3:Eu without and with CTAB surfactant was studied. FTIR studies reveal that CTAB surfactant plays an important role in converting cubic Gd2O3:Eu to hexagonal Gd(OH)(3):Eu. The strong and intense Raman peak at 489 cm(-1) has been assigned to A(g) mode, which is attributed to the hexagonal phase of Gd2O3. The peak at similar to 360 cm(-1) has been assigned to the combination of F-g and E-g modes, which is mainly attributed to the cubic Gd2O3 phase. The shift in frequency and broadening of the Raman modes have been attributed to the decrease in crystallite dimension to the nanometer scale as a result of phonon confinement. (C) 2010 Elsevier B.V. All rights reserved.

Preparation and characterization of multiwall carbon nanotube/polypyrrole coaxial fibrils

Multiwall carbon nanotube (MWNT)/polypyrrole (PPy) fibrils were fabricated by template-free in situ electrochemical deposition of PPy over MWNTs, and characterized by electron microscopy and electrical measurements. Scanning and transmission electron microscopy studies reveal that PPy coating on the surface of nanotube is quite uniform throughout the length, with the possibility of forming unique Y-junctions. Current (I)-voltage (V) characteristics at various temperatures show nonlinearity due to tunneling and hopping contributions to transport across the barriers. AC conductivity measurements (300-4.2 K) show that the onset frequency scales with temperature, and the nanoscale connectivity in MWNT/PPy fibrils decreases with the lowering of temperature. (C) 2011 Elsevier B.V. All rights reserved.

Simultaneous purification of biotin-binding proteins-I and -II from chicken egg yolk and their characterization

Chicken egg yolk biotin-binding protein-I (BBP-I) has been purified to homogeneity along with the tetrameric BBP-II by a common protocol. The purification includes delipidation of egg yolk by butanol extraction, DEAE-Sephacel chromatography, treatment with guanidinium chloride and biotin-aminohexyl-Sepharose affinity chromatography. The identity of purified BBP-I was ascertained by its physicochemical properties as well as by its immunological cross-reactivity and precursor-product relationship with BBP-II.

Synthesis and characterization of photo-crosslinkable main-chain liquid-crystalline polymers containing bis(benzylidene)cycloalkanone units

A series of new photo-crosslinkable main-chain liquid-crystalline polymers containing bis(benzylidene)cycloalkanone units have been studied. These units in the polymers function as mesogens as well as photoactive centres. Polyesters with three different bis(4-hydroxybenzylidene)cycloalkanones corresponding to three cycloalkanones, namely cyclopentanone, cyclohexanone and cycloheptanone, have been prepared. Three dicarboxylic acids with ether linkages, which were derived from oligoethylene oxides, namely triethylene glycol, tetraethylene glycol and pentaethylene glycol, have been used as spacers in these polymers. Polymerization was carried out by both solution and interfacial polycondensation; the latter method gave high-molecular-weight polymers. Structural characterizations were done by ultra-violet, infra-red and H-1 nuclear magnetic resonance spectroscopy. Liquid-crystalline properties were studied by differential scanning calorimetry and polarized-light optical microscopy. These polymers show a nematic mesophase. Liquid-crystalline transition temperatures were correlated with polymer structure. The decrease in transition temperature with increase in cycloalkanone ring size was explained in terms of the change in geometrical anisotropy of bis(benzylidene)cycloalkanone units. MNDO (modified neglect of differential overlap) calculations were performed on the model compounds, bis(4-acetyloxybenzylidene)cycloalkanone to elucidate the geometrical variation of the mesogenic units with cycloalkanone ring size. Studies of photolysis reveal the two kinds of photoreactions that proceed in these polymer systems, namely photoisomerization and photo-crosslinking. The former reaction disrupts the parallel stacking of the chromophores and is reflected as an increase in the ultra-violet spectral intensity. The favourability of these two reactions depends on the mobility of the polymer chains. When the photolysis was done below T-g, photo-crosslinking dominates over photoisomerization. Above T-g, photoisomerization is followed by photo-crosslinking. The photosensitivity of the polymers decreases with increase in size of the cycloalkanone ring.

Immunochemical characterization of rapid and slowly released allergens from the pollen of Parthenium hysterophorus

Allergens from the pollen of Parthenium hysterophorus (American feverfew), responsible for high incidence of allergic rhinitis, were found by immunoprint analysis to be localized on the surface of the pollen grains. The allergens were released very rapidly when extracted in vitro. The allergenic activity of the rapid (10 s) and slowly (20 h) released pollen proteins was comparable by in vivo skin test and ELISA inhibition assay. The isoelectric focusing patterns of the rapid and slowly released proteins, were also identical. SDS-PAGE and Western blot analysis revealed that all the major pollen allergens with molecular weight 14, 28, 31, 37 and 45 kDa were eluted within 10 s of extraction. Periodate-Schiff staining showed that the 28, 31 and 45 kDa components of the pollen extract are glycoproteins. The pollen allergens released after different periods of extraction lost 75% of IgE binding activity when subjected to in situ sodium m-periodate oxidation under controlled conditions, while 80% of the allergenic activity was still retained after extensive proteolysis. Our results support the clinical observation of a rapid onset of symptoms of allergic rhinitis in patients sensitive to Parthenium pollen, mediated predominantly by glycoproteins.

Influence of Alkali Ions in Enhancing the Nonlinearity of ZnO-Bi2O3-Co3O4 Varistor Ceramics

Zinc oxide ceramic varistors with simplified compositions of ZnO+Bi2O3+Co3O4+M(2)O (M=K or Na) show nonlinearity coefficients (alpha) of 40-75. The electron paramagnetic resonance spectra and optical reflectance spectra show that there is a direct interdependence between the oxidation state of transition metals and the alkali ions. The X-ray photoelectron spectra indicate that the alkali ions preserve a higher oxidation state of cobalt, Co(III), in the grain boundary regions than in the grain interiors having more Co(II). Admittance spectroscopy shows that, while the nature of traps remains unaltered, the trap density increases with the concentration of alkali ions near the interface. The observed defect states are associated with the grain bulk than with the grain boundary interfaces, as indicated by the isothermal capacitance transient signals

Multifunctional cryogenic sensors from n-BaTiO3 ceramics having strong negative temperature coefficient of resistance

Donor-doped n-BaTiO3 polycrystalline ceramics show a strong negative temperature coefficient of resistivity below the orthorhombic-rhombohedral phase transition point, from 10(2-3) Omega cm af 190 K to 10(10-13) Omega cm at less than or similar to 50 K, with thermal coefficient of resistance alpha = 20-23% K-1. Stable thermal sensors for low-temperature applications are realized therefrom. The negative temperature coefficient of resistivity region can be modified by substituting isovalent ions in the lattice. Highly nonlinear current-voltage (I-V) curves are observed at low temperatures, with a voltage maximum followed by the negative differential resistance. The I-V curves are sensitive to dissipation so that cryogenic sensors can be fabricated for liquid level control, flow rate monitoring, radiation detection or in-rush voltage limitation.

Preparation and Characterization of Single-Phase Beta-Sialon

A simple method for the preparation of monophasic beta-SiAlON using nitridation of Si and AIN with an oxygen partial pressure of 10(-4) atm is described. The effect of the AlN/Si ratio in the initial mixture on the formation of beta-SiAlON is discussed. The likely mechanism of the formation of beta-SiAlON is outlined.

Production of biosurfactant “Biosur-Pm” by Pseudomonas maltophila CSV89: characterization and role in hydrocarbon uptake

Pseudomonas maltophilia CSV89, a soil bacterium, produces an extracellular biosurfactant, ''Biosur-Pm''. The partially purified product is nondialyzable and chemically composed of 50% protein and 12-15% sugar, which indicates the complex nature of Biosur-Pm. It reduces the surface tension of water from 73 to 53 x 10(-3) N m(-1) and has a critical micellar concentration of 80 mg/l. Compared to aliphatic hydrocarbons, Biosur-Pm shows good activity against aromatic hydrocarbons. The emulsion formed is stable and does not require any metal ions for emulsification. The kinetics of Biosur-Pm production suggest that its synthesis isa growth-associated and pH-dependent process. At pH 7.0, cells produced more Biosur-Pm with less cell surface hydrophobicity. At pH 8.0, however, the cells produced less Biosur-Pm with more cell surface hydrophobicity and showed a twofold higher affinity for aromatic hydrocarbons compared to the cells grown at pH 7.0. The Biosur-Pm showed a pH-dependent release, stimulated growth of the producer strain on mineral salts medium with 1-naphthoic acid when added externally, and facilitated the conversion of salicylate to catechol. All these results suggest that Biosur-Pm is probably a cell-wall component and helps in hydrocarbon assimilation/uptake.

Purification and characterization of DNA-dependent RNA polymerase II from Candida utilis

DNA-dependent RNA polymerase II from Candida utilis has been purified to near homogeneity. The purified enzyme resolved into three subforms, viz. IIO, IIA and IIB. On SDS-PAGE the enzyme showed ten polypeptides with molecular weights in the range of 205 kDa to 14 kDa. By two dimensional electrophoresis (IEF followed by SDS-PAGE) the presence of basic and acidic polypeptides has been demonstrated. The enzyme showed Km values of 5, 5.6 and 8 mu M for GTP, CTP and ATP, respectively, and the activity was inhibited by low levels of oc-amanitin and antibodies raised against bovine RNA polymerase II. By Western blot analysis the enzyme was found to cross-react with antibodies to bovine RNA polymerase II. RNA polymerase II from G. utilis is a phosphoprotein, the subunits RPB1 and RPB10 were found to be phosphorylated. Analysis of carboxy-terminal domain indicated that it was functionally redundant at least in case of nonspecific transcription, implicating its role in other nuclear processes, such as promoter specific initiation or transcription activation or RNA processing.

Purification and partial characterization of acyl carrier proteins from developing oil seeds of pisa (Actinodaphne hookeri) and ground nut (Arachis hypogaea)

Acyl carrier proteins (ACP) were purified to homogeneity in the active form from developing seeds of pisa (Actinodaphne hookeri) which synthesizes exclusively trilaurin and from ground nut (Arachis hypogaea) which synthesizes triacylglycerols containing long chain fatty acids. Two major isoforms of ACPs were purified from developing pisa seeds using DEAE-cellulose, Superose-6 FPLC and C-4 reversed phase HPLC chromatographic methods. In contrast, only a single form of ACP was present in ground nut seeds which was purified by anion-exchange and activated thiol-Sepharose 4B affinity chromatography. The two isoforms of ACPs from pisa showed nearly the same specific activity of 6,706 and 7,175 pmol per min per mg protein while ground nut ACP showed a specific activity of 3,893 pmol per min per mg protein when assayed using E. coli acyl-ACP synthetase and [1-C-14]palmitic acid. When compared with E. coli ACP, the purified ACPs from both the seeds showed considerable difference in their mobility in native PAGE, but showed similar mobility in SDS-PAGE under reducing conditions. In the absence of reducing agents formation of dimers was quite prominent. The ACPs from both the seed sources were acid- and heat-stable. The major isoform of pisa seed ACP and the ground nut ACP contain 91 amino acids with M(r) 11,616 and 1,228 respectively. However, there is significant variation in their amino acid composition. A comparision of the amino acid sequence in the N-terminal region of pisa and ground nut seed ACPs showed considerable homology between themselves and with other plant ACPs but not with E. coli ACP.

Microstructural and dielectric properties of KCl-added bismuth vanadate ceramics

The effect of KCI addition on the microstructural, structural and dielectric properties of bismuth vanadate, Bi2VO5.5 (BiV) has been examined. The average grain size of BN ceramics increases with increase in KCl content (from an average grain size of TO to 80 mu m) as a result of the increased liquid-phase formation of KCI, at the grain boundaries. Differential scanning calorimetry (DSC) carried out on the KCl-added samples indicates an upward shift in the transition temperature (T-c), from 723 K (for BN) to 734 K (for 5 mol% KCl-added BiV). On further increase in the KCI content, T-c shifts down to about 722 K for 10 mol%. This trend is consistent with that of the lattice strain data. The relative permittivity as well as the dielectric loss decrease by more than half of the original values upon the addition of KCI. The relative permittivities of the KCl-added ceramics are comparable with the values predicted by the logarithmic mixture rule. Impedance analyses suggest that the grain boundary resistance of the KCl-added BiV ceramics is higher by two orders of magnitude than that of BN ceramics. The KCl-added BN ceramics exhibit ferroelectric domains and the domain density decreases as the grain boundary region is approached.

Preparation and characterization of Cd(0.75)PS(3)A(0.5)(H2O)(y) [A = Na, K and Cs]

Cd(0.75)PS(3)A(0.5)(H2O)(y) [A = Na, K and Cs], synthesized by the ion-exchange intercalation reaction of the insulating layered CdPS3, exhibits interesting electrical properties. The electrical properties are strongly dependent on the extent of hydration of the alkali ion which resides in the interlamellar space. In the potassium and caesium ion-exchanged compounds, y = I, the lattice expansion is similar to 3 Angstrom and the electric response characteristic of a dielectric. In the as prepared A = Na compound, y = 2, the lattice expansion is 5.6 Angstrom, the compound is conducting with a DC conductance of 3 x 10(-5) S cm(-1) at 300 K. Cd0.75PS3Na0.5(H2O)(y), y = 2, on evacuation or on heating looses water, reversibly, to form a y = 1 phase with electrical properties similar to that of the K and Cs ion exchange intercalation compounds.