Development and transient performance results of a single stage activated carbon - HFC 134a closed cycle adsorption cooling system

A laboratory model of a thermally driven adsorption refrigeration system with activated carbon as the adsorbent and 1,1,1,2-tetrafluoroethane (HFC 134a) as the refrigerant was developed. The single stage compression system has an ensemble of four adsorbers packed with Maxsorb II specimen of activated carbon that provide a near continuous flow which caters to a cooling load of up to 5W in the 5-18 degrees C region. The objective was to utilise the low grade thermal energy to drive a refrigeration system that can be used to cool some critical electronic components. The laboratory model was tested for it performance at various cooling loads with the heat source temperature from 73 to 93 degrees C. The pressure transients during heating and cooling phases were traced. The cyclic steady state and transient performance data are presented. (C) 2010 Elsevier Ltd. All rights reserved.

Investigations of a two-stage pulse tube cryocooler operating down to 2.5K

A two-stage pulse tube cryocooler (PTC) which produces a no-load temperature of similar to 2.5 K in its second stage at an operating frequency of 1.6 Hz has been designed and fabricated. The second stage of the system provides a refrigeration power of similar to 250 mW at 5.0 K. The system uses stainless steel meshes (mesh size 200) along with lead (Pb) granules and combinations of Pb, Er3Ni, and HoCu2 as the first and second stage regenerator materials, respectively. Experimental studies have been carried out on different pulse tube configurations by varying the dimensions of the pulse tubes and regenerators to arrive at the best one, which leads to the lowest no-load second stage cold head temperature. Using this configuration, detailed experimental studies have been conducted by varying the volume percentage ratios of the second stage regenerator materials such as HoCu2, Er3Ni, and Pb (with an average grain size of similar to 250 mu m). This article presents the results of our experimental studies on cryocoolers with the regenerator material arranged in layered structures. Comparative studies have also been presented for specific cases where the regenerator materials are arranged as a homogeneous mixture in the second stage. The experimental results clearly indicate that the design of PTCs should use only layered structures of regenerator materials and not homogenous mixtures.

Kinetics of two-stage crystallization in Metglas 2826A

Crystallization kinetics of MSI and MSII stages in Metglas 2826A has been investigated by quantitative transmission electron microscopy. The volume fraction of crystallization against time curve has been found to show a plateau in the lower temperature region of annealing. It has been found that the glass transition temperature, T g, has no effect on the sequence reversal of the crystallization reaction. It has been shown that the sequence reversal of transformation stages occurs due to the large difference in the activation energy of crystallization of MSI and MSII. In addition, the change in the morphology of the crystals obtained by annealing the amorphous alloy below and above the glass transition temperature, T g, is reported.

Development of Nonsocial Behaviour in the Asiatic Elephant

The elephant calf, a defended follower is completely dependent on adults till the age of 3 months. It begins to explore and attempts to feed at 3 to 6 months, and then becomes partially independent with some feeding on its own. The characteristics of behavior in adults are examined and the development of this pattern in the calf is traced by analyis of duration, transition and clustering of the behavioural elements. Essential activities like suckling, locomotion and lying down for rest appear soon after birth whereas elements of feeding, grooming and play appear only at a later stage. The calf takes the initiative in suckling and its termination, drinking directly by mouth till the age of 6 months. The first element of feeding appears at about a week in attempts to pick up and hold objects in the trunk. Co-ordination of limb, trunk and mouth movement is achieved by about 1 month. The calf is strong enough to pull out plants by 6 months when independent feeding begins. In about a year feeding, drinking and dusting patterns are well developed.

Interaction of synthetic analogs of distamycin and netropsin with nucleic acids. Does curvature of ligand play a role in distamycin-DNA interactions?

Distamycin and netropsin, a class of minor groove binding nonintercalating agents, are characterized by their B-DNA and A-T basespecific interactions. To understand the CQI I ~OIT~ ~ I ~ ~aOnMd ~c hemical basis of the above specificities, the DNA-binding characteristics of a novel synthetic analogue of distamycin have been studied. The analogue, mPD derivative, has the requisite charged end groups and a number of potential hydrogen-bonding loci equal to those of distamycin. The difference in the backbone curvatures of the ligands, distamycin, the mPD derivative, and NSC 101327 (another structurally analogous compound),is a major difference between these ligands. UV and CD spectrosoopic studies reported here show the following salient features: The mPD derivative recognizes only B-DNA, to which it binds via the minor groove. On the other hand, unlike distamycin, it binds with comparable affinities to A-T and G-C base pairs in a natural DNA. These DNA-binding properties are compared with those reported earlier for distamycin and NSC 101327 [Zimmer, Ch., & Wahnert, U. (1986) Prog. Biophys. Mol. Biol. 47, 31-1121. The backbone structures of these three ligands were compared to show the progressive decrease in curvatures in the order distamycin, mPD derivative, and NSC 101327. The plausible significance of the backbone curvature vis-&vis the characteristic B-DNA and AT-specific binding of distamycin is discussed. To our knowledge, this is the first attempt (with a model synthetic analogue) to probe the possible influence of backbone curvature upon the specificity of interactions of the distamycin class of groove-binding ligands with DNA.

Two-stage photoquenching in semi-insulating GaAs:EL2

The photoquenching of EL2 in semi‐insulating gallium arsenide is seen to be a complex process, where at low temperatures the initial slow quenching is followed by a switch to fast quenching. A possible explanation involving lattice strain mediated cooperative structural relaxation arising out of transition to the metastable state is proposed.

Development stage-specific expression of fibroin in the silk worm Bombyx mori is regulated translationally

The contents of fibroin H RNA as a function of development have been quantitated in the posterior silk glands of Bombyx mori larvae on different days of 4th and 5th instars. The fibroin RNA levels increased during the feeding stages of larvae and the RNA got completely degraded during the interim moult. The patterns of accumulation of fibroin RNA were similar in both the instars. Although there was considerable increase in the fibroin RNA content during the 5th larval instar, the relative abundance of fibroin RNA in the total RNA was fairly constant during the 4th and 5th instars. The increased content of fibroin RNA in 5th instar was the consequence of an overall increase in transcription accompanying the development progress, rather than specific increase only in fibroin transcription. The contents of fibroin protein in the 4th and 5th instars of development have also been quantitated making use of a sensitive radioimmune assay with a purified, antifibroin antibody. There were substantial differences between 4th and 5th instars in the absolute fibroin contents as well as the relative proportion of fibroin in the total proteins. These results implied that although the fibroin gene was transcribed at the same efficiency during the 4th and 5th instars, the translational efficiency was much lower during the 4th instar. The extent of polyadenylation of fibroin RNA was similar in both instars. However, there was a two-fold increase in the polysome association of fibroin RNA in the 5th instar. Over and above this, there was substantial increase during the 5th instar in the contents of those tRNAs. (e.g. Gly, Ala and Ser) which are abundantly represented in fibroin and therefore directly related to the expression of fibroin. The increased polysome association of fibroin mRNA and the adequate supply of cognate tRNAs in the 5th instar, together contributes to the translational regulation of fibroin in a developmental stage-specific manner. Based on these observations, we propose that translational regulation plays a major role in the development stage-specific synthesis of fibroin in Bombyx mori.

A multi-stage model for drop breakage in stirred vessels

Existing models for dmax predict that, in the limit of μd → ∞, dmax increases with 3/4 power of μd. Further, at low values of interfacial tension, dmax becomes independent of σ even at moderate values of μd. However, experiments contradict both the predictions show that dmax dependence on μd is much weaker, and that, even at very low values of σ,dmax does not become independent of it. A model is proposed to explain these results. The model assumes that a drop circulates in a stirred vessel along with the bulk fluid and repeatedly passes through a deformation zone followed by a relaxation zone. In the deformation zone, the turbulent inertial stress tends to deform the drop, while the viscous stress generated in the drop and the interfacial stress resist deformation. The relaxation zone is characterized by absence of turbulent stress and hence the drop tends to relax back to undeformed state. It is shown that a circulating drop, starting with some initial deformation, either reaches a steady state or breaks in one or several cycles. dmax is defined as the maximum size of a drop which, starting with an undeformed initial state for the first cycle, passes through deformation zone infinite number of times without breaking. The model predictions reduce to that of Lagisetty. (1986) for moderate values of μd and σ. The model successfully predicts the reduced dependence of dmax on μd at high values of μd as well as the dependence of dmax on σ at low values of σ. The data available in literature on dmax could be predicted to a greater accuracy by the model in comparison with existing models and correlations.

A multi-stage model for drop breakage in stirred vessels

Existing models for dmax predict that, in the limit of μd → ∞, dmax increases with 3/4 power of μd. Further, at low values of interfacial tension, dmax becomes independent of σ even at moderate values of μd. However, experiments contradict both the predictions show that dmax dependence on μd is much weaker, and that, even at very low values of σ,dmax does not become independent of it. A model is proposed to explain these results. The model assumes that a drop circulates in a stirred vessel along with the bulk fluid and repeatedly passes through a deformation zone followed by a relaxation zone. In the deformation zone, the turbulent inertial stress tends to deform the drop, while the viscous stress generated in the drop and the interfacial stress resist deformation. The relaxation zone is characterized by absence of turbulent stress and hence the drop tends to relax back to undeformed state. It is shown that a circulating drop, starting with some initial deformation, either reaches a steady state or breaks in one or several cycles. dmax is defined as the maximum size of a drop which, starting with an undeformed initial state for the first cycle, passes through deformation zone infinite number of times without breaking. The model predictions reduce to that of Lagisetty. (1986) for moderate values of μd and σ. The model successfully predicts the reduced dependence of dmax on μd at high values of μd as well as the dependence of dmax on σ at low values of σ. The data available in literature on dmax could be predicted to a greater accuracy by the model in comparison with existing models and correlations.

Do the Hydrolysis Products, Methylamine and N,N'-Dimethylurea, Play any Role in the Methyl Isocyanate-Induced Haematological and Biochemical Changes in Rabbits?

The subcutaneous administration of methyl isocyanate (MIC) to female rabbits, resulted in significant increases in haemoglobin concentration, erythrocyte volume fraction and leucocyte number in blood, as well as plasma total proteins, and urea. The present study was designed to investigate whether the hydrolytic products of MIC, methylamine (MA) and N,N'-dimethylurea (DMU) play any role in eliciting these changes. Both MA and DMU administered subcutaneously in an equimolar dose to that of 1.0 LD50 MIC, 2.2 mmol kg-1, had no influence on these parameters, although there was a marginal increase in the plasma urea level shortly after the administration of DMU. This study establishes that the observed haematological and biochemical changes induced by MIC intoxication in rabbits are mostly due to MIC.

The stability of transmembrane helices: A molecular dynamics study on the isolated helices of bacteriorhodopsin

Bacteriorhodopsin (bR) continues to be a proven testing ground for the study of integral membrane proteins (IMPs). It is important to study the stability of the individual helices of bR, as they are postulated to exist as independently stable transmembmne helices (TMHs) and also for their utility as templates for modeling other IMPs with the postulated seven-helix bundle topology. Toward this purpose, the seven helices of bR have been studied by molecular dynamics simulation in this study. The suitability of using the backbone-dependent rotamer library of side-chain conformations arrived at from the data base of globular protein structures in the case TMHs has been tested by another set of ? helix simulations with the side-chain orientations taken from this library. The influence of the residue's net charge oil the helix stability was examined by simulating the helices III, IV, and VI (from both of the above sets of helices) with zero net charge on the side chains. The results of these 20 simulations demonstrate in general the stability of the isolated helices of bR in conformity with the two-stage hypothesis of IMP folding. However, the helices I, II, V, and VII are more stable than the other three helices. The helical nature of certain regions of III, IV, and VI are influenced by factors such as the net charge and orientation of several residues. It is seen that the residues Arg, Lys, Asp, and Glu (charged residues), and Ser, Thr, Gly, and Pro, play a crucial role in the stability of the helices of bR. The backbone-dependent rotamer library for the side chains is found to be suitable for the study of TMHs in IMP. (C) 1996 John Wiley & Sons, Inc.

Two-Stage Extended Kalman Filters with Derivative-Free Local Linearizations

This paper proposes a derivative-free two-stage extended Kalman filter (2-EKF) especially suited for state and parameter identification of mechanical oscillators under Gaussian white noise. Two sources of modeling uncertainties are considered: (1) errors in linearization, and (2) an inadequate system model. The state vector is presently composed of the original dynamical/parameter states plus the so-called bias states accounting for the unmodeled dynamics. An extended Kalman estimation concept is applied within a framework predicated on explicit and derivative-free local linearizations (DLL) of nonlinear drift terms in the governing stochastic differential equations (SDEs). The original and bias states are estimated by two separate filters; the bias filter improves the estimates of the original states. Measurements are artificially generated by corrupting the numerical solutions of the SDEs with noise through an implicit form of a higher-order linearization. Numerical illustrations are provided for a few single- and multidegree-of-freedom nonlinear oscillators, demonstrating the remarkable promise that 2-EKF holds over its more conventional EKF-based counterparts. DOI: 10.1061/(ASCE)EM.1943-7889.0000255. (C) 2011 American Society of Civil Engineers.

Two stage iterative wiener filtering for speech enhancement

We formulate a two-stage Iterative Wiener filtering (IWF) approach to speech enhancement, bettering the performance of constrained IWF, reported in literature. The codebook constrained IWF (CCIWF) has been shown to be effective in achieving convergence of IWF in the presence of both stationary and non-stationary noise. To this, we include a second stage of unconstrained IWF and show that the speech enhancement performance can be improved in terms of average segmental SNR (SSNR), Itakura-Saito (IS) distance and Linear Prediction Coefficients (LPC) parameter coincidence. We also explore the tradeoff between the number of CCIWF iterations and the second stage IWF iterations.