Electrical switching studies on Ge-Te-Tl chalcogenide glasses: Effect of thallium on the composition dependence of switching voltages

Bulk Ge(17)Te83_,JI glasses (05x.5_13), have been found to exhibit memory type electrical switching. The switching voltages (also known as threshold voltage V-th) of Ge17Te83-xTlx glasses are found to decrease with increasing thallium content. The rate of decrease of Vtry is greater at lower concentrations and \textbackslashid, falls at a slower rate for higher thallium concentrations (x 6). The addition of thallium to the Ge-Te network fragments the covalent network and introduces ionic nature to it; the reduction in network connectivity leads to the decrease in switching voltages with thallium content. The decrease in the glass transition temperatures of Ge17Te83-xTlx glasses with increasing thallium concentration supports the idea of decrease in network connectivity with TI addition. The more metallic nature of TI also contributes to the observed reduction in the switching voltages of Ge17Te83-xTlx glasses with TI content. Further, there is an interesting correlation seen between the threshold voltage V-th and the average bond energy, as a function of TI content. In addition, the switching voltages of Ge17Te83-xTlx glasses have been found to decrease with sample thickness almost linearly. The set-reset studies indicate that the Ge17Te83-xTl2 sample can be switched for more than 10 cycles, whereas other glasses could not be reset beyond two switching cycles. (C) 2010 Elsevier B.V. All rights reserved.

Synthesis of Cuprates of Perovskite Structure in the Ba-Pb-Cu-O, Ba-Bi-Cu-O, and Ba-Pb-Tl-Cu-O Systems: Possible High Tc Superconductivity in a Perovskite-like Phase in the Ba-Pb-Tl-Cu-O System

Cubic cuprates (a not, vert, similar 18.6 Å) with a BaCuO2-type structure were obtained in the Ba-Pb-Cu-O and Ba-Bi-Cu-O systems by the reaction of the component oxides at a high temperature (1370-1420 K), followed by quenching. By annealing these phases in oxygen at 1070-1120 K, perovskite-like phase (a not, vert, similar 4.3 Å) of the formulae BaPb1-xCuxO3-y and BaBi1-xCuxO3-y (0 < x ? 0.5) were obtained. A perovskite of nominal composition BaPb0.25Tl0.25 Cu0.5O3-y, prepared by a similar procedure, was found to be superconducting with a Tc of not, vert, similar 70 K.

Development and studies on microstrip detector

We report development of gas microstrip detectors using thin film and lithography techniques. The detectors were tested for their performance for X-rays (5.9 keV) and a maximum gas gain of similar to 13,000 and best resolution of similar to 12% was obtained. Factors affecting gain and resolution were investigated. The detectors were tested for their one-dimensional position sensitivity. Meandering resistive strips were used for charge division method. A position resolution of 0.48 mm was obtained.

A Novel VSI- and CSI-Fed Dual Stator Induction Motor Drive Topology for Medium-Voltage Drive Applications

A new configuration is proposed for high-power induction motor drives. The induction machine is provided with two three-phase stator windings with their axes in line. One winding is designed for higher voltage and is meant to handle the main (active) power. The second winding is designed for lower voltage and is meant to carry the excitation (reactive) power. The excitation winding is powered by an insulated-gate-bipolar-transistor-based voltage source inverter with an output filter. The power winding is fed by a load-commutated current source inverter. The commutation of thyristors in the load-commutated inverter (LCI) is achieved by injecting the required leading reactive power from the excitation inverter. The MMF harmonics due to the LCI current are also cancelled out by injecting a suitable compensating component from the excitation inverter, so that the electromagnetic torque of the machine is smooth. Results from a prototype drive are presented to demonstrate the concept.

Precoder Designs for MIMO Broadcast Channels with Imperfect CSI

[1] D. Tse and P. Viswanath, Fundamentals of Wireless Communication.Cambridge University Press, 2006. [2] H. Bolcskei, D. Gesbert, C. B. Papadias, and A.-J. van der Veen, Spacetime Wireless Systems: From Array Processing to MIMO Communications.Cambridge University Press, 2006. [3] Q. H. Spencer, C. B. Peel, A. L. Swindlehurst, and M. Haardt, “An introduction to the multiuser MIMO downlink,” IEEE Commun. Mag.,vol. 42, pp. 60–67, Oct. 2004. [4] K. Kusume, M. Joham,W. Utschick, and G. Bauch, “Efficient tomlinsonharashima precoding for spatial multiplexing on flat MIMO channel,”in Proc. IEEE ICC’2005, May 2005, pp. 2021–2025. [5] R. Fischer, C. Windpassinger, A. Lampe, and J. Huber, “MIMO precoding for decentralized receivers,” in Proc. IEEE ISIT’2002, 2002, p.496. [6] M. Schubert and H. Boche, “Iterative multiuser uplink and downlink beamforming under SINR constraints,” IEEE Trans. Signal Process.,vol. 53, pp. 2324–2334, Jul. 2005. [7] ——, “Solution of multiuser downlink beamforming problem with individual SINR constraints,” IEEE Trans. Veh. Technol., vol. 53, pp.18–28, Jan. 2004. [8] A. Wiesel, Y. C. Eldar, and Shamai, “Linear precoder via conic optimization for fixed MIMO receivers,” IEEE Trans. Signal Process., vol. 52,pp. 161–176, Jan. 2006. [9] N. Jindal, “MIMO broadcast channels with finite rate feed-back,” in Proc. IEEE GLOBECOM’2005, Nov. 2005. [10] R. Hunger, F. Dietrich, M. Joham, and W. Utschick, “Robust transmit zero-forcing filters,” in Proc. ITG Workshop on Smart Antennas, Munich,Mar. 2004, pp. 130–137. [11] M. B. Shenouda and T. N. Davidson, “Linear matrix inequality formulations of robust QoS precoding for broadcast channels,” in Proc.CCECE’2007, Apr. 2007, pp. 324–328. [12] M. Payaro, A. Pascual-Iserte, and M. A. Lagunas, “Robust power allocation designs for multiuser and multiantenna downlink communication systems through convex optimization,” IEEE J. Sel. Areas Commun.,vol. 25, pp. 1392–1401, Sep. 2007. [13] M. Biguesh, S. Shahbazpanahi, and A. B. Gershman, “Robust downlink power control in wireless cellular systems,” EURASIP Jl. Wireless Commun. Networking, vol. 2, pp. 261–272, 2004. [14] B. Bandemer, M. Haardt, and S. Visuri, “Liner MMSE multi-user MIMO downlink precoding for users with multple antennas,” in Proc.PIMRC’06, Sep. 2006, pp. 1–5. [15] J. Zhang, Y. Wu, S. Zhou, and J. Wang, “Joint linear transmitter and receiver design for the downlink of multiuser MIMO systems,” IEEE Commun. Lett., vol. 9, pp. 991–993, Nov. 2005. [16] S. Shi, M. Schubert, and H. Boche, “Downlink MMSE transceiver optimization for multiuser MIMO systems: Duality and sum-mse minimization,”IEEE Trans. Signal Process., vol. 55, pp. 5436–5446, Nov.2007. [17] A. Mezghani, M. Joham, R. Hunger, and W. Utschick, “Transceiver design for multi-user MIMO systems,” in Proc. WSA 2006, Mar. 2006. [18] R. Doostnejad, T. J. Lim, and E. Sousa, “Joint precoding and beamforming design for the downlink in a multiuser MIMO system,” in Proc.WiMob’2005, Aug. 2005, pp. 153–159. [19] N. Vucic, H. Boche, and S. Shi, “Robust transceiver optimization in downlink multiuser MIMO systems with channel uncertainty,” in Proc.IEEE ICC’2008, Beijing, China, May 2008. [20] A. Ben-Tal and A. Nemirovsky, “Selected topics in robust optimization,”Math. Program., vol. 112, pp. 125–158, Feb. 2007. [21] D. Bertsimas and M. Sim, “Tractable approximations to robust conic optimization problems,” Math. Program., vol. 107, pp. 5–36, Jun. 2006. [22] P. Ubaidulla and A. Chockalingam, “Robust Transceiver Design for Multiuser MIMO Downlink,” in Proc. IEEE Globecom’2008, New Orleans, USA, Dec. 2008, to appear. [23] S. Boyd and L. Vandenberghe, Convex Optimization. Cambridge University Press, 2004. [24] G. H. Golub and C. F. V. Loan, Matrix Computations. The John Hopkins University Press, 1996.

Solution processed reduced graphene oxide ultraviolet detector

Electronic properties of graphene have been studied more extensively than its photonic applications, in spite of its exciting optical properties. Recent results on solar cells, light emitting diodes and photodetectors show its true potential in photonics and optoelectronics. Here, we have explored the use of reduced graphene oxide as a candidate for solution processed ultraviolet photodetectors. UV detection is demonstrated by reduced graphene oxide in terms of time resolved photocurrent as well as photoresponse. The responsivity of the detectors is found to be 0.12 A/W with an external quantum efficiency of 40%. (C) 2011 American Institute of Physics. [doi:10.1063/1.3640222]

Robust MMSE Tomlinson-Harashima Precoder for Multiuser MISO Downlink with Imperfect CSI

Non-linear precoding for the downlink of a multiuser MISO (multiple-input single-output) communication system in the presence of imperfect channel state information (CSI) is considered.The base station is equipped with multiple transmit antennas and each user terminal is equipped with a single receive antenna. The CSI at the transmitter is assumed to be perturbed by an estimation error. We propose a robust minimum mean square error (MMSE) Tomlinson-Harashima precoder (THP)design, which can be formulated as an optimization problem that can be solved efficiently by the method of alternating optimization(AO). In this method of optimization, the entire set of optimization variables is partitioned into non-overlapping subsets,and an iterative sequence of optimizations on these subsets is carried out, which is often simpler compared to simultaneous optimization over all variables. In our problem, the application of the AO method results in a second-order cone program which can be numerically solved efficiently. The proposed precoder is shown to be less sensitive to imperfect channel knowledge. Simulation results illustrate the improvement in performance compared to other robust linear and non-linear precoders in the literature.

Relay Precoder Optimization in MIMO-Relay Networks With Imperfect CSI

In this paper, we consider robust joint designs of relay precoder and destination receive filters in a nonregenerative multiple-input multiple-output (MIMO) relay network. The network consists of multiple source-destination node pairs assisted by a MIMO-relay node. The channel state information (CSI) available at the relay node is assumed to be imperfect. We consider robust designs for two models of CSI error. The first model is a stochastic error (SE) model, where the probability distribution of the CSI error is Gaussian. This model is applicable when the imperfect CSI is mainly due to errors in channel estimation. For this model, we propose robust minimum sum mean square error (SMSE), MSE-balancing, and relay transmit power minimizing precoder designs. The next model for the CSI error is a norm-bounded error (NBE) model, where the CSI error can be specified by an uncertainty set. This model is applicable when the CSI error is dominated by quantization errors. In this case, we adopt a worst-case design approach. For this model, we propose a robust precoder design that minimizes total relay transmit power under constraints on MSEs at the destination nodes. We show that the proposed robust design problems can be reformulated as convex optimization problems that can be solved efficiently using interior-point methods. We demonstrate the robust performance of the proposed design through simulations.

A Novel VSI- and CSI-Fed Active-Reactive Induction Motor Drive with Sinusoidal Voltages and Currents

Till date load-commutated inverter (LCI)-fed synchronous motor drive configuration is popular in high power applications (>10 MW). The leading power factor operation of synchronous motor by excitation control offers this simple and rugged drive structure. On the contrary, LCI-fed induction motor drive is absent as it always draws lagging power factor current. Therefore, complicated commutation circuit is required to switch off thyristors for a current source inverter (CSI)-driven induction motor. It poses the major hindrance to scale up the power rating of CSI-fed induction motor drive. Anew power topology for LCI-fed induction motor drive for medium-voltage drive application is proposed. A new induction machine (active-reactive induction machine) with two sets of three-phase winding is introduced as a drive motor. The proposed power configuration ensures sinusoidal voltage and current at the motor terminals. The total drive power is shared among a thyristor-based LCI, an insulated gate bipolar transistor (IGBT)-based two-level voltage source inverter (VSI), and a three-level VSI. The benefits of SCRs and IGBTs are explored in the proposed drive. Experimental results from a prototype drive verify the basic concepts of the drive.

Microprocessor-Based Field-Oriented Control of A CSI-Fed Induction Motor Drive

This paper describes the method of field orientation of the stator current vector with respect to the stator, mutual, and rotor flux vectors, for the control of an induction motor fed from a current source inverter (CSI). A control scheme using this principle is described for orienting the stator current with respect to the rotor flux, as this gives natural decoupling between the current coordinates. A dedicated micro-computer system developed for implementing this scheme has been described. The experimental results are also presented.

Design and performance analysis of a signal detector based on suprathreshold stochastic resonance

This paper presents the design and performance analysis of a detector based on suprathreshold stochastic resonance (SSR) for the detection of deterministic signals in heavy-tailed non-Gaussian noise. The detector consists of a matched filter preceded by an SSR system which acts as a preprocessor. The SSR system is composed of an array of 2-level quantizers with independent and identically distributed (i.i.d) noise added to the input of each quantizer. The standard deviation sigma of quantizer noise is chosen to maximize the detection probability for a given false alarm probability. In the case of a weak signal, the optimum sigma also minimizes the mean-square difference between the output of the quantizer array and the output of the nonlinear transformation of the locally optimum detector. The optimum sigma depends only on the probability density functions (pdfs) of input noise and quantizer noise for weak signals, and also on the signal amplitude and the false alarm probability for non-weak signals. Improvement in detector performance stems primarily from quantization and to a lesser extent from the optimization of quantizer noise. For most input noise pdfs, the performance of the SSR detector is very close to that of the optimum detector. (C) 2012 Elsevier B.V. All rights reserved.

Thermal diffusivity measurements on ternary Ge-Te-Tl glasses using Photo-thermal Deflection method: Effect of thallium addition

Photo-thermal Deflection (PTD) technique is used to investigate the thermal diffusivity (alpha) of Ge17Te83 - xTlx (0 <= x <= 13) glasses as a function of composition. The thermal diffusivity of these glasses is found to lie in the range 0.020 to 0.048 cm(2)/s, which is consistent with the memory type of electrical switching exhibited by these samples. Further, it is found that alpha shows an initial increase with Tl addition, followed by a decrease. The observed composition dependence of thermal diffusivity has been understood on the basis that the thallium atoms are incorporated as a covalent species for lower values of x, increasing the network rigidity; however, they enter as ionic species for higher x values, fragmenting the network. The initial increase in a is due to the increasing network rigidity and the subsequent decrease is because of the fragmentation of the network. Also, there is a strong correlation between the composition dependence of switching voltages observed earlier and the variation with composition of electrical resistivity and thermal diffusivity of Ge17Te83 - xTlx glasses obtained in the present study. (C) 2012 Elsevier B.V. All rights reserved.

Decode-and-forward relay beamforming for secrecy with imperfect CSI and multiple eavesdroppers

In this paper, we evaluate secrecy rates in cooperative relay beamforming in the presence of imperfect channel state information (CSI) and multiple eavesdroppers. A source-destination pair aided by.. out of.. relays, 1 <= k <= M, using decode-and-forward relay beamforming is considered. We compute the worst case secrecy rate with imperfect CSI in the presence of multiple eavesdroppers, where the number of eavesdroppers can be more than the number of relays. We solve the optimization problem for all possible relay combinations to find the secrecy rate and optimum source and relay weights subject to a total power constraint. We relax the rank-1 constraint on the complex semi-definite relay weight matrix and use S-procedure to reformulate the optimization problem that can be solved using convex semi-definite programming.

Single electron transfer-driven multi-dimensional signal read-out function of TCNQ as an ``off-the-shelf'' detector for cyanide

Herein we report the first applications of TCNQ as a rapid and highly sensitive off-the-shelf cyanide detector. As a proof-of-concept, we have applied a kinetically selective single-electron transfer (SET) from cyanide to deep-lying LUMO orbitals of TCNQ to generate a persistently stable radical anion (TCNQ(center dot-)), under ambient condition. In contrast to the known cyanide sensors that operate with limited signal outputs, TCNQ(center dot-) offers a unique multiple signaling platform. The signal readability is facilitated through multichannel absorption in the UV-vis-NIR region and scattering-based spectroscopic methods like Raman spectroscopy and hyper Rayleigh scattering techniques. Particularly notable is the application of the intense 840 nm NIR absorption band to detect cyanide. This can be useful for avoiding background interference in the UV-vis region predominant in biological samples. We also demonstrate the fabrication of a practical electronic device with TCNQ as a detector. The device generates multiorder enhancement in current with cyanide because of the formation of the conductive TCNQ(center dot-).

Achievable secrecy sum-rate in a fading MAC-WT with power control and without CSI of eavesdropper

We consider a two user fading Multiple Access Channel with a wire-tapper (MAC-WT) where the transmitter has the channel state information (CSI) to the intended receiver but not to the eavesdropper (eve). We provide an achievable secrecy sum-rate with optimal power control. We next provide a secrecy sum-rate with optimal power control and cooperative jamming (CJ). We then study an achievable secrecy sum rate by employing an ON/OFF power control scheme which is more easily computable. We also employ CJ over this power control scheme. Results show that CJ boosts the secrecy sum-rate significantly even if we do not know the CSI of the eve's channel. At high SNR, the secrecy sum-rate (with CJ) without CSI of the eve exceeds the secrecy sum-rate (without CJ) with full CSI of the eve.