Characterisation of cellulose- and lignin-based materials using x-ray scattering methods

Wood is an important material for the construction and pulping industries. Using x-ray diffraction the microfibril angle of Sitka spruce wood was studied in the first part of this thesis. Sitka spruce (Picea sitchensis [Bong.] Carr.) is native to the west coast of North America, but due to its fast growth rate, it has also been imported to Europe. So far, its nanometre scale properties have not been systematically characterised. In this thesis the microfibril angle of Sitka spruce was shown to depend significantly on the origin of the tree in the first annual rings near the pith. Wood can be further processed to separate lignin from cellulose and hemicelluloses. Solid cellulose can act as a reducer for metal ions and it is also a porous support for nanoparticles. By chemically reducing nickel or copper in the solid cellulose support it is possible to get small nanoparticles on the surfaces of the cellulose fibres. Cellulose supported metal nanoparticles can potentially be used as environmentally friendly catalysts in organic chemistry reactions. In this thesis the size of the nickel and copper containing nanoparticles were studied using anomalous small-angle x-ray scattering and wide-angle x-ray scattering. The anomalous small-angle x-ray scattering experiments showed that the crystallite size of the copper oxide nanoparticles was the same as the size of the nanoparticles, so the nanoparticles were single crystals. The nickel containing nanoparticles were amorphous, but crystallised upon heating. The size of the nanoparticles was observed to be smaller when the reduction of nickel was done in aqueous ammonium hydrate medium compared to reduction made in aqueous solution. Lignin is typically seen as the side-product of wood industries. Lignin is the second most abundant natural polymer on Earth, and it possesses potential to be a useful material for many purposes in addition to being an energy source for the pulp mills. In this thesis, the morphology of several lignins, which were produced by different separation methods from wood, was studied using small-angle and ultra small-angle x-ray scattering. It was shown that the fractal model previously proposed for the lignin structure does not apply to most of the extracted lignin types. The only lignin to which the fractal model could be applied was kraft lignin. In aqueous solutions the average shape of the low molar mass kraft lignin particles was observed to be elongated and flat. The average shape does not necessarily correspond to the shape of the individual particles because of the polydispersity of the fraction and due to selfassociation of the particles. Lignins, and especially lignosulfonate, have many uses as dispersants, binders and emulsion stabilisers. In this thesis work the selfassociation of low molar mass lignosulfonate macromolecules was observed using small-angle x-ray scattering. By taking into account the polydispersity of the studied lignosulfonate fraction, the shape of the lignosulfonate particles was determined to be flat by fitting an oblate ellipsoidal model to the scattering intensity.

The Politics of Pulp Investment and the Brazilian Landless Movement (MST)

The Politics of Pulp Investment and the Brazilian Landless Movement (MST) The paper industry has been moving more heavily to the global South at the beginning of the 21st century. In a number of cases the rural populations of the global South have engaged in increasingly important resistance in their scuffle with the large-scale tree plantation-relying pulp investment model. The resistance had generally not yet managed to slow down Southern industrial tree plantation expansion until 2004. After all, even the MST, perhaps the strongest of the Southern movements, has limited power in comparison to the corporations pushing for plantation expansion. This thesis shows how, even against these odds, depending on the mechanisms of contention and case-specific conflict dynamics, in some cases the movements have managed to slow and even reverse plantation expansion. The thesis is based on extensive field research in the Brazilian countryside. It outlines a new theory of contentious agency promotion, emphasizing its importance in the shaping of corporate resource exploitation. The thesis includes a Qualitative Comparative Analysis of resistance influence on the economic outcomes of all (14) Brazilian large-scale pulp projects between 2004-2008. The central hypothesis of the thesis is that corporate resource exploitation can be slowed down more effectively and likely when the resistance is based on contentious agency. Contentious agency is created by the concatenation of five mutually supporting mechanisms of contention: organizing and politicizing a social movement; heterodox framing of pulp projects; protesting; networking; and embedding whilst maintaining autonomy. The findings suggest that contentious agency can slow or even reverse the expansion of industrial plantations, whereas when contentious agency promotion was inactive, fast or even unchecked plantation expansion was always the outcome. The rule applied to all the assessed 14 pulp conflict cases. The hypothesis gained strong support even in situations where corporate agency promotion was simultaneously active. In previous studies on social movements, there has been a lack of contributions that help us understand the causal mechanisms of contention influencing economic outcomes. The thesis answers to the call by merging a Polanyian analysis of the political economy with the Dynamics of Contention research program and making a case for the impact of contentious agency on capital accumulation. The research concludes that an efficient social movement can utilize mechanisms of contention to promote the potential of activism among its members and influence investment outcomes. Protesting, for example via pioneering land occupations, seemed to be particularly important. Until now, there has been no comprehensive theory on when and how contentious agency can slow down or reverse the expansion of corporate resource exploitation. The original contribution of this research is to provide such a theory, and utilize it to offer an extensive explanation on the conflicts over pulp investment in Brazil, the globalization of the paper industry, and slowing of industrial plantation expansion in the global South.

Pulp and Paper Fiction: On the Discursive Legitimation of Global Industrial Restructuring

Despite the central role of legitimacy in social and organizational life, we know little of the subtle meaning-making processes through which organizational phenomena, such as industrial restructuring, are legitimated in contemporary society. Therefore, this paper examines the discursive legitimation strategies used when making sense of global industrial restructuring in the media. Based on a critical discourse analysis of extensive media coverage of a revolutionary pulp and paper sector merger, we distinguish and analyze five legitimation strategies: (1) normalization, (2) authorization, (3) rationalization, (4) moralization, and (5) narrativization. We argue that while these specific legitimation strategies appear in individual texts, their recurring use in the intertextual totality of the public discussion establishes the core elements of the emerging legitimating discourse.

Harvesting undelimbed Scots pine (Pinus sylvestris L.) from first thinnings for integrated production of kraft pulp and energy

The present study evaluates the feasibility of undelimbed Scots pine (Pinus sylvestris L.) for integrated production of pulp and energy in a kraft pulp mill from the technical, economic and environmental points of view, focusing on the potential of bundle harvesting. The feasibility of tree sections for pulp production was tested by conducting an industrial wood-handling experiment, laboratory cooking and bleaching trials, using conventional small-diameter Scots pine pulpwood as a reference. These trials showed that undelimbed Scots pine sections can be processed in favourable conditions as a blend with conventional small-diameter pulpwood without reducing the pulp quality. However, fibre losses at various phases of the process may increase when using undelimbed material. In the economic evaluation, both pulp production and wood procurement costs were considered, using the relative wood paying capability of a kraft pulp mill as a determinant. The calculations were made for three Scots pine first-thinning stands with the breast-height diameter of the removal (6 12 cm) as the main distinctive factor. The supply chains included in the comparison were based on cut-to-length harvesting, whole-tree harvesting and bundle harvesting (whole-tree bundling). With the current ratio of pulp and energy prices, the wood paying capability declines with an increase in the proportion of the energy fraction of the raw material. The supply system based on the cut-to-length method was the most efficient option, resulting in the highest residual value at stump in most cases. A decline in the pulp price and an increase in the energy price improved the competitiveness of the whole-tree systems. With short truck transportation distances and low pulp prices, however, the harvesting of loose whole trees can result in higher residual value at stump in small-diameter stands. While savings in transportation costs did not compensate for the high cutting and compaction costs by the second prototype of the bundle harvester, an increase in transportation distances improved its competitiveness. Since harvesting undelimbed assortments increases nutrient export from the site, which can affect soil productivity, the whole-tree alternatives included in the present study cannot be recommended on infertile peatlands and mineral soils. The harvesting of loose whole trees or bundled whole trees implies a reduction in protective logging residues and an increase in site traffic or payloads. These factors increase the risk of soil damage, especially on peat soils with poor bearing capacity. Within the wood procurement parameters which were examined, the CO2 emissions of the supply systems varied from 13 27 kg m3. Compaction of whole trees into bundles reduced emissions from transportation by 30 39%, but these reductions were insufficient to compensate for the increased emissions from cutting and compaction.

Inhibitory effects of wood extracts on the spoilage flora of marinated poultry meat

Polyphenolic compounds occurring naturally in knotwood of plants are known to have antimicrobial effects. The knots (i.e. the branch bases inside tree stems) and outer branches in pine trees contain a remarkably high concentration of phenolic stilbenes, while lignans are the major phenolic constituents of spruce knots. Large amount of these phenolic compounds can be extracted from wood knots at pulp and paper mills where their presence is undesirable. In Finland, marinating of broiler meat is done not only to increase or add value to the meat, but also to enhance the safety and shelf-life. These products are usually packed under a modified atmosphere for further protection against spoilage microorganisms. However, studies have revealed that addition of marinades to poultry products do not have an inhibitory effect on either some psychrotrophic anaerobic bacteria, such as Brochothrix thermosphacta or lactic acid bacteria associated with spoilage. Also, the activity of pathogenic Campylobacter jejuni is not affected by marinating. The objective of this study was to investigate the inhibitory and lethal activities of extracts from spruce (Picea spp.) and pine (Pinus spp.) knotwood and outer branches that are dissolved in ethanol against the spoilage microorganisms in modified atmosphere packaged marinated broiler products. Modified atmosphere packaged broiler products were separately inoculated with ‘normal’ marinades, marinades with 70% ethanol, marinades with a mixture of spruce and pine extracts dissolved in 70% ethanol or mixture of spruce and pine extracts in powder form. The bacterial colony forming units per gram obtained from each of the samples were analysed on de Man Rogosa and Sharpe agar at days 1, 6, 12 and 15. The results showed that there were significant differences in bacterial colony forming units per gram (P <0.05) between packages with ‘normal’ marinades and packages with extracts added to their marinades on the 12th and 15th day. It can be concluded that the addition of extracts from spruce and pine knotwood to marinades significantly retarded growth of spoilage microorganisms during the 15 day test period. However further research is warranted to characterise and establish the safety and suitability of the compound(s) in spruce and pine knotwood extracts that are responsible for inhibitory or lethal activity against the microbes that may be present in marinated poultry meat.

Measuring attitudes in translation: a study of Nokia business reports

Background Contemporary Finnish, spoken and written, reveals loanwords or foreignisms in the form of hybrids: a mixture of Finnish and foreign syllables (alumiinivalua). Sometimes loanwords are inserted into the Finnish sentence in their raw form just as they are found in the source language (pulp, after sales palvelu). Again, sometimes loanwords are calques, which appear Finnish but are spelled and pronounced in an altogether foreign manner (Protomanageri, Promenadi kampuksella). Research Questions What role does Finnish business translation play in the migration of foreignisms into Finnish if we consider translation "as a construct of solutions determined by the ideological constraints and conflicts characterizing the target culture" (Robyns 1992: 212)? What attitudes do the Finns display toward the presence of foreignisms in their language? What socio-economic or ideological conditions (Bassnett 1994: 321) are responsible for these attitudes? Are these conditions dynamic? What tools can be used to measure such attitudes? This dissertation set out to answer these and similar questions. Attitudes are imperialist (where otherness is both denied and transformed), defensive (where otherness is acknowledged, transformed, and vilified), transdiscursive (a neutral attitude to both otherness and transformation), or finally defective (where alien migration is acknowledged and "stimulated") (Robyns 1994: 60). Methodology The research method follows Rose's schema (1984: 8): (a) take an existing theory, (b) develop from it a proposition specific enough to be tested, (c) devise a scheme that tests this proposition, (d) carry through the scheme in practice, (e) draw up results and discuss conclusions in relation to the original theory. In other words, the method attempts an explanation of a Finnish social phenomenon based on systematic analyses of translated evidence (Lewins 1992: 4) whereby what really matters is the logical sequence that connects the empirical data to the initial research questions raised above and, ultimately to its conclusion (Yin 1984: 29). Results This research found that Finnish translators of the Nokia annual reports used a foreignism whenever possible such as komponentin instead of rakenneosa, or investoida instead of sijoittaa, and often without any apparent justification (Pryce 2003: 203-12) more than the translator's personal preference. In the old documents (minutes of meetings of the Board of Directors of Osakeyhtio H. Saastamoinen, Ltd. dated 5 July 1912-1917, a NOPSA booklet (1932), Enzo-Gutzeit-Tornator Oy document (1938), Imatra Steel Oy Annual Report 1964, and Nokia Oy Annual Report 1946), foreignisms under Haugen's (1950: 210-31) Classification #1 occurred an average of 0.6 times, while in the new documents (Nokia 1998 translated Annual Reports) they occurred an average of 6.5 times. That big difference, suggests transdiscursive and defective attitudes in Finnish society toward the other. In the 1850s, Finnish attitudes toward alien persons and cultures were hardened, intolerant and prohibitive because language politics were both nascent and emerging, and Finns adopted a defensive stance (Paloposki 2002: 102 ff) to protect their cultural and national treasures such as language and folklore. Innovation The innovation here is that no prior doctoral level research measured Finnish attitudes toward foreignisms using a business translation approach. This is the first time that Haugen's classification has been modified and applied in target language analysis. It is hoped that this method would be replicated in similar research in the future. Applications For practical applications, researchers with interest in languages, language development, language influences, language ideologies, and power structures that affect national language policies will find this thesis useful, especially the model for collecting, grouping, and analyzing foreignisms that has been demonstrated here. It is intended to document for posterity current attitudes of Finns toward the other as revealed in business translations from 1912-1964, and in 1998. This way, future language researchers would be able to explore a time-line of Finnish language development and attitudes toward the other. Communication firms may also find this research interesting. In future, could the model we adopted be used to analyze literary texts or religious texts for example? Future Trends Though business documents show transdiscursive attitudes, other segments of Finnish society may show defensive or imperialist attitudes. When the ideology of industrialization changes in the future, will Finnish attitudes toward the other change as well? Will it then be possible to use the same kind of analytical tools to measure Finnish attitudes? More broadly, will linguistic change continue in the same direction of transdiscursive attitudes, or will the change slow down or even reverse into xenophobic attitudes? Is this our model culture-specific or can it be used in the context of other cultures? Conclusion There is anger against foreignisms in Finland as newspaper publications and television broadcasts show, but research shows that a majority of Finns consider foreignisms and the languages from which they come as sources of enrichment for Finnish culture (Laitinen 2000, Eurobarometer series 41 of July 1994, 44 of Spring 1996, 50 of Autumn 1998). Ideologies of industrialization and globalization in Finland have facilitated transdiscursive tendencies. When Finland's political ideology was intolerant toward foreign influences in the 1850s because Finland was in the process of consolidating her nascent country and language, attitudes toward the importation of loanwords also became intolerant. Presently, when industrialization and globalization became the dominant ideologies, we see a shift in attitudes toward transdiscursive tendencies. Ideology is usually unseen and too often ignored by translation researchers. However, ideology reveals itself as the most powerful factor affecting language attitudes in a target culture. Key words Finnish, Business Translation, Ideology, Foreignisms, Imperialist Attitudes, Defensive Attitudes, Transdiscursive Attitudes, Defective Attitudes, the Other, Old Documents, New Documents.

Stone Weathering in the Monastic Building Complex on Mountain of St Aaron in Petra, Jordan.

Since 1997 the Finnish Jabal Haroun Project (FJHP) has studied the ruins of the monastery and pilgrimage complex (Gr. oikos) of Aaron located on a plateau of the Mountain of Prophet Aaron, Jabal an-Nabi Harûn, ca. 5 km to the south-west of the UNESCO World Heritage site of Petra in Jordan. The state of conservation and the damaging processes affecting the stone structures of the site are studied in this M.A. thesis. The chapel was chosen as an example, as it represents the phasing and building materials of the entire site. The aim of this work is to act as a preliminary study with regards to the planning of long-term conservation at the site. The research is empirical in nature. The condition of the stones in the chapel walls was mapped using the Illustrated Glossary on Stone Deterioration, by the ICOMOS International Scientific Committee for Stone. This glossary combines several standards and systems of damage mapping used in the field. Climatic conditions (temperature and RH %) were monitored for one year (9/2005-8/2006) using a HOBO Microstation datalogger. The measurements were compared with contemporary measurements from the nearest weather station in Wadi Musa. Salts in the stones were studied by taking samples from the stone surfaces by scraping and with the “Paper Pulp”-method; with a poultice of wet cellulose fiber (Arbocel BC1000) and analyzing what main types of salts were to be found in the samples. The climatic conditions on the mountain were expected to be rapidly changing and to differ clearly from conditions in the neighboring areas. The rapid changes were confirmed, but the values did not differ as much as expected from those nearby: the 12 months monitored had average temperatures and were somewhat drier than average. Earlier research in the area has shown that the geological properties of the stone material influence its deterioration. The damage mapping showed clearly, that salts are also a major reason for stone weathering. The salt samples contained several salt combinations, whose behavior in the extremely unstable climatic conditions is difficult to predict. Detailed mapping and regular monitoring of especially the structures, that are going remain exposed, is recommended in this work.

Tracking and identifying wastewater toxicants and assessing their biodegradation products

Screening of wastewater effluents from municipal and industrial wastewater treatment plants with biotests showed that the treated wastewater effluents possess only minor acute toxic properties towards whole organisms (e.g. bacteria, algae, daphnia), if any. In vitro tests (sub-mitochondrial membranes and fish hepatocytes) were generally more susceptible to the effluents. Most of the effluents indicated the presence of hormonally active compounds, as the production of vitellogenin, an egg yolk precursor protein, was induced in fish hepatocytes exposed to wastewater. In addition, indications of slight genotoxic potential was found in one effluent concentrate with a recombinant bacteria test. Reverse electron transport (RET) of mitochondrial membranes was used as a model test to conduct effluent assessment followed by toxicant characterisations and identifications. Using a modified U.S. EPA Toxicity Identification Evaluation Phase I scheme and additional case-specific methods, the main compound in a pulp and paper mill effluent causing RET inhibition was characterised to be an organic, relatively hydrophilic high molecular weight (HMW) compound. The toxicant could be verified as HMW lignin by structural analyses using nuclear magnetic resonance. In the confirmation step commercial and in-house extracted lignin products were used. The possible toxicity related structures were characterised by statistical analysis of the chemical breakdown structures of laboratory-scale pulping and bleaching effluents and the toxicities of these effluents. Finally, the biological degradation of the identified toxicant and other wastewater constituents was evaluated using bioassays in combination with chemical analyses. Biological methods have not been used routinely in establishing effluent discharge limits in Finland. However, the biological effects observed in this study could not have been predicted using only routine physical and chemical effluent monitoring parameters. Therefore chemical parameters cannot be considered to be sufficient in controlling effluent discharges especially in case of unknown, possibly bioaccumulative, compounds that may be present in small concentrations and may cause chronic effects.

Microbial life and deposits in paper machine circuits

Väitöskirjani käsittele mikrobien ja erilaisten kemikaalien rooleja saostumien ja biofilmien muodostumisessa paperi- ja kartonkikoneilla. "Saostuma" tässä työssä tarkoittaa kiinteän aineen kertymää konepinnoille tai rajapinnoille konekierroissa, jotka on tarkoitettu massasulppujen, lietteiden, vesien tai ilman kuljetukseen. Saostumasta tulee "biofilmi" silloin kun sen oleellinen rakennekomponentti on mikrobisolut tai niiden tuotteet. Väitöstyöni työhypoteesina oli, että i. tietämys saostumien koostumuksesta, sekä ii. niiden rakenteesta, biologisista, fysikaalis-kemiallisista ja teknisistä ominaisuuksista ohjaavat tutkijaa löytämään ympäristöä säästäviä keinoja estää epätoivottujen saostumien muodostus tai purkaa jo muodostuneita saostumia. Selvittääkseni saostumien koostumista ja rakennetta käytin monia erilaisia analytiikan työkaluja, kuten elektronimikroskopiaa, konfokaali-laser mikroskopiaa (CLSM), energiadispersiivistä röntgenanalyysiä (EDX), pyrolyysi kaasukromatografiaa yhdistettynä massaspektrometriaan (Py-GCMS), joninvaihtokromatografiaa, kaasukromatografiaa ja mikrobiologisia analyysejä. Osallistuin aktiivisesti innovatiivisen, valon takaisinsirontaan perustuvan sensorin kehittämistyöhön, käytettäväksi biofilmin kasvun mittaukseen suoraan koneen vesikierroista ja säiliöistä. Työni osoitti, että monet paperinvalmistuksessa käytetyistä kemikaaleista reagoivat keskenään tuottaen orgaanisia tahmakerroksia konekiertojen teräspinnoille. Löysin myös kerrostumia, jotka valomikroskooppisessa tarkastelussa oli tulkittu mikrobeiksi, mutta jotka elektronimikroskopia paljasti alunasta syntyneiksi, alumiinihydroksidiksi joka saostui pH:ssa 6,8 kiertokuitua käyttävän koneen viiravesistä. Monet paperintekijät käyttävät vieläkin alunaa kiinnitysaineena vaikka prosessiolot ovat muuttuneet happamista neutraaleiksi. Sitä pidetään paperitekijän "aspiriinina", mutta väitöstutkimukseni osoitti sen riskit. Löysin myös orgaanisia saostumia, joiden alkuperä oli aineiden, kuten pihkan, saippuoituminen (kalsium saippuat) niin että muodostui tahmankasvua ylläpitävä alusta monilla paperi- ja kartonkikoneilla. Näin solumuodoiltaan Deinococcus geothermalista muistuttavia bakteereita kasvamassa lujasti teräskoepalojen pintaan kiinnittyneinä pesäkkeinä, kun koepaloja upotettiin paperikoneiden vesikiertoihin. Nämä deinokokkimaiset pesäkkeet voivat toimia jalustana, tarttumisalustana muiden mikrobien massoille, joka selittäisi miksi saostumat yleisesti sisältävät deinokokkeja pienenä, muttei koskaan pääasiallisena rakenneosana. Kun paperikoneiden käyttämien vesien (raakavedet, lämminvesi, biologisesti puhdistettu jätevesi) laatua tutkitaan, mittausmenetelmällä on suuri merkitys. Koepalan upotusmenetelmällä todettu biofilmikasvu ja viljelmenetelmällä mitattu bakteerisaastuneisuus korreloivat toisiinsa huonosti etenkin silloin kun likaantumisessa oli mukana rihmamaiseti kasvavia bakteereja. Huoli ympäristöstä on pakottanut paperi- ja kartonkikoneiden vesikiertojen sulkemiseen. Vesien kierrätys ja prosessivesien uudelleenkäyttö nostavat prosessilämpötilaa ja lisäävät koneella kiertävien kolloidisten ja liuenneiden aineiden määriä. Tutkin kiertovesien pitoisuuksia kolmessa eriasteisesti suljetussa tehtaassa, joiden päästöt olivat 0 m3, 0,5 m3 ja 4 m3 jätevettä tuotetonnia kohden, perustuen puhdistetun jäteveden uudelleen käyttöön. Nollapäästöisellä tehtaalla kiertovesiin kertyi paljon orgaanisesti sidottua hiiltä (> 10 g L-1), etenkin haihtuvina happoina (maito-, etikka-, propioni- ja voi-). Myös sulfaatteja, klorideja, natriumia ja kalsiumia kertyi paljon, > 1 g L-1 kutakin. Pääosa (>40%) kaikista bakteereista oli 16S rRNA geenisekvenssianalyysien tulosten perusteella sukua, joskin etäistä (< 96%) ainoastaan Enterococcus cecorum bakteerille. 4 m3 päästävältä tehtaalta löytyi lisäksi Bacillus thermoamylovorans ja Bacillus coagulans. Tehtaiden saostumat sisälsivät arkkeja suurina pitoisuuksina, ≥ 108 g-1, mutta tunnistukseen riittävää sekvenssisamanlaisuutta löytyi vain yhteen arkkisukuun, Methanothrix. Tutkimustulokset osoittivat että tehtaan vesikiertojen sulkeminen vähensi rajusti mikrobiston monimuotoisuutta, muttei estänyt liuenneen aineen ja kiintoaineen mineralisoitumista.