SU-8-Based Microchips for Capillary Electrophoresis and Electrospray Ionization Mass Spectrometry

Miniaturization of analytical instrumentation is attracting growing interest in response to the explosive demand for rapid, yet sensitive analytical methods and low-cost, highly automated instruments for pharmaceutical and bioanalyses and environmental monitoring. Microfabrication technology in particular, has enabled fabrication of low-cost microdevices with a high degree of integrated functions, such as sample preparation, chemical reaction, separation, and detection, on a single microchip. These miniaturized total chemical analysis systems (microTAS or lab-on-a-chip) can also be arrayed for parallel analyses in order to accelerate the sample throughput. Other motivations include reduced sample consumption and waste production as well as increased speed of analysis. One of the most promising hyphenated techniques in analytical chemistry is the combination of a microfluidic separation chip and mass spectrometer (MS). In this work, the emerging polymer microfabrication techniques, ultraviolet lithography in particular, were exploited to develop a capillary electrophoresis (CE) separation chip which incorporates a monolithically integrated electrospray ionization (ESI) emitter for efficient coupling with MS. An epoxy photoresist SU-8 was adopted as structural material and characterized with respect to its physicochemical properties relevant to chip-based CE and ESI/MS, namely surface charge, surface interactions, heat transfer, and solvent compatibility. As a result, SU-8 was found to be a favorable material to substitute for the more commonly used glass and silicon in microfluidic applications. In addition, an infrared (IR) thermography was introduced as direct, non-intrusive method to examine the heat transfer and thermal gradients during microchip-CE. The IR data was validated through numerical modeling. The analytical performance of SU-8-based microchips was established for qualitative and quantitative CE-ESI/MS analysis of small drug compounds, peptides, and proteins. The CE separation efficiency was found to be similar to that of commercial glass microchips and conventional CE systems. Typical analysis times were only 30-90 s per sample indicating feasibility for high-throughput analysis. Moreover, a mass detection limit at the low-attomole level, as low as 10E+5 molecules, was achieved utilizing MS detection. The SU-8 microchips developed in this work could also be mass produced at low cost and with nearly identical performance from chip to chip. Until this work, the attempts to combine CE separation with ESI in a chip-based system, amenable to batch fabrication and capable of high, reproducible analytical performance, have not been successful. Thus, the CE-ESI chip developed in this work is a substantial step toward lab-on-a-chip technology.

The effects of environmental factors on biomass and microcystin production by the freshwater cyanobacterial genera Microcystis and Anabaena

Several cyanobacterial genera produce the hepatotoxins, microcystins. Microcystins are produced only in cells that have microcystin synthetase gene (mcy) clusters, which encode enzyme complexes involved in microcystin biosynthesis. Microcystin-producing and nonmicrocystin-producing genotypes of single cyanobacterial genus may occur simultaneously in situ. Previously, the effects of environmental factors on the growth and microcystin production of cyanobacteria have mainly been studied by means of isolated cyanobacteria cultures in the laboratory. Studies in the field have been difficult, owing to the lack of methods to identify and quantify the different genotypes. In this study, genus-specific microcystin synthetase E (mcyE) gene primers were designed and a method to identify and quantify the mcyE copy numbers was developed and used in situ. Microcystis and Anabaena mcyE genes were observed in two Finnish lakes. Microcystis appeared to be the most abundant microcystin producer in Lake Tuusulanjärvi and in one basin of Lake Hiidenvesi. Because the most potent microcystin-producing genus of a lake can be identified, it will be possible in the future to design genus-targeted strategies for lake restoration. Effects of P and N concentrations on the biomass of microcystin-producing and nonmicrocystin-producing Microcystis strains and an Anabaena strain were studied in cultures. P and N concentrations and their combined effect increased cyanobacterial biomass of all Microcystis strains. The biomass of microcystin-producing Microcystis was higher than that of nonmicrocystin-producing strains at high nutrient concentrations. The P concentration increased Anabaena biomass, but the effect of N concentration was statistically insignificant for growth yield, probably due to the ability of the genus to fix molecular N2. P and N concentrations and combined nutrients caused an increase in cellular microcystin concentrations of the Microcystis strain cultivated in chemostat cultures. Cyanobacteria are able to hydrolyse nutrients from organic matter through extracellular enzyme activities. Leucine aminopeptidase (LAP) activity was observed in an axenic N2-fixing Anabaena strain grown in batch cultures. The P concentration caused a statistically significant increase in LAP activity, whereas the effect of N concentration was insignificant. The highest LAP activities were observed in the most eutrophic basins of Lake Hiidenvesi. LAP activity probably originated mostly from attached heterotrophic bacteria and less from cyanobacteria.

Information, risk and trust in the food chain : Ex-ante valuation of consumer willingness to pay for beef quality information using the contingent valuation method

The safety of food has become an increasingly interesting issue to consumers and the media. It has also become a source of concern, as the amount of information on the risks related to food safety continues to expand. Today, risk and safety are permanent elements within the concept of food quality. Safety, in particular, is the attribute that consumers find very difficult to assess. The literature in this study consists of three main themes: traceability; consumer behaviour related to both quality and safety issues and perception of risk; and valuation methods. The empirical scope of the study was restricted to beef, because the beef labelling system enables reliable tracing of the origin of beef, as well as attributes related to safety, environmental friendliness and animal welfare. The purpose of this study was to examine what kind of information flows are required to ensure quality and safety in the food chain for beef, and who should produce that information. Studying the willingness to pay of consumers makes it possible to determine whether the consumers consider the quantity of information available on the safety and quality of beef sufficient. One of the main findings of this study was that the majority of Finnish consumers (73%) regard increased quality information as beneficial. These benefits were assessed using the contingent valuation method. The results showed that those who were willing to pay for increased information on the quality and safety of beef would accept an average price increase of 24% per kilogram. The results showed that certain risk factors impact consumer willingness to pay. If the respondents considered genetic modification of food or foodborne zoonotic diseases as harmful or extremely harmful risk factors in food, they were more likely to be willing to pay for quality information. The results produced by the models thus confirmed the premise that certain food-related risks affect willingness to pay for beef quality information. The results also showed that safety-related quality cues are significant to the consumers. In the first place, the consumers would like to receive information on the control of zoonotic diseases that are contagious to humans. Similarly, other process-control related information ranked high among the top responses. Information on any potential genetic modification was also considered important, even though genetic modification was not regarded as a high risk factor.

Parameters Affecting the Extraction of Polycyclic Aromatic Hydrocarbons with Pressurised Hot Water

Pressurised hot water extraction (PHWE) exploits the unique temperature-dependent solvent properties of water minimising the use of harmful organic solvents. Water is environmentally friendly, cheap and easily available extraction medium. The effects of temperature, pressure and extraction time in PHWE have often been studied, but here the emphasis was on other parameters important for the extraction, most notably the dimensions of the extraction vessel and the stability and solubility of the analytes to be extracted. Non-linear data analysis and self-organising maps were employed in the data analysis to obtain correlations between the parameters studied, recoveries and relative errors. First, pressurised hot water extraction (PHWE) was combined on-line with liquid chromatography-gas chromatography (LC-GC), and the system was applied to the extraction and analysis of polycyclic aromatic hydrocarbons (PAHs) in sediment. The method is of superior sensitivity compared with the traditional methods, and only a small 10 mg sample was required for analysis. The commercial extraction vessels were replaced by laboratory-made stainless steel vessels because of some problems that arose. The performance of the laboratory-made vessels was comparable to that of the commercial ones. In an investigation of the effect of thermal desorption in PHWE, it was found that at lower temperatures (200ºC and 250ºC) the effect of thermal desorption is smaller than the effect of the solvating property of hot water. At 300ºC, however, thermal desorption is the main mechanism. The effect of the geometry of the extraction vessel on recoveries was studied with five specially constructed extraction vessels. In addition to the extraction vessel geometry, the sediment packing style and the direction of water flow through the vessel were investigated. The geometry of the vessel was found to have only minor effect on the recoveries, and the same was true of the sediment packing style and the direction of water flow through the vessel. These are good results because these parameters do not have to be carefully optimised before the start of extractions. Liquid-liquid extraction (LLE) and solid-phase extraction (SPE) were compared as trapping techniques for PHWE. LLE was more robust than SPE and it provided better recoveries and repeatabilities than did SPE. Problems related to blocking of the Tenax trap and unrepeatable trapping of the analytes were encountered in SPE. Thus, although LLE is more labour intensive, it can be recommended over SPE. The stabilities of the PAHs in aqueous solutions were measured using a batch-type reaction vessel. Degradation was observed at 300ºC even with the shortest heating time. Ketones and quinones and other oxidation products were observed. Although the conditions of the stability studies differed considerably from the extraction conditions in PHWE, the results indicate that the risk of analyte degradation must be taken into account in PHWE. The aqueous solubilities of acenaphthene, anthracene and pyrene were measured, first below and then above the melting point of the analytes. Measurements below the melting point were made to check that the equipment was working, and the results were compared with those obtained earlier. Good agreement was found between the measured and literature values. A new saturation cell was constructed for the solubility measurements above the melting point of the analytes because the flow-through saturation cell could not be used above the melting point. An exponential relationship was found between the solubilities measured for pyrene and anthracene and temperature.

Precipitation-induced runoff and leaching from milled peat mining mires by peat types : a comparative method for estimating the loading of water bodies during peat pruduction

Precipitation-induced runoff and leaching from milled peat mining mires by peat types: a comparative method for estimating the loading of water bodies during peat production. This research project in environmental geology has arisen out of an observed need to be able to predict more accurately the loading of watercourses with detrimental organic substances and nutrients from already existing and planned peat production areas, since the authorities capacity for insisting on such predictions covering the whole duration of peat production in connection with evaluations of environmental impact is at present highly limited. National and international decisions regarding monitoring of the condition of watercourses and their improvement and restoration require more sophisticated evaluation methods in order to be able to forecast watercourse loading and its environmental impacts at the stage of land-use planning and preparations for peat production.The present project thus set out from the premise that it would be possible on the basis of existing mire and peat data properties to construct estimates for the typical loading from production mires over the whole duration of their exploitation. Finland has some 10 million hectares of peatland, accounting for almost a third of its total area. Macroclimatic conditions have varied in the course of the Holocene growth and development of this peatland, and with them the habitats of the peat-forming plants. Temperatures and moisture conditions have played a significant role in determining the dominant species of mire plants growing there at any particular time, the resulting mire types and the accumulation and deposition of plant remains to form the peat. The above climatic, environmental and mire development factors, together with ditching, have contributed, and continue to contribute, to the existence of peat horizons that differ in their physical and chemical properties, leading to differences in material transport between peatlands in a natural state and mires that have been ditched or prepared for forestry and peat production. Watercourse loading from the ditching of mires or their use for peat production can have detrimental effects on river and lake environments and their recreational use, especially where oxygen-consuming organic solids and soluble organic substances and nutrients are concerned. It has not previously been possible, however, to estimate in advance the watercourse loading likely to arise from ditching and peat production on the basis of the characteristics of the peat in a mire, although earlier observations have indicated that watercourse loading from peat production can vary greatly and it has been suggested that differences in peat properties may be of significance in this. Sprinkling is used here in combination with simulations of conditions in a milled peat production area to determine the influence of the physical and chemical properties of milled peats in production mires on surface runoff into the drainage ditches and the concentrations of material in the runoff water. Sprinkling and extraction experiments were carried out on 25 samples of milled Carex (C) and Sphagnum (S) peat of humification grades H 2.5 8.5 with moisture content in the range 23.4 89% on commencement of the first sprinkling, which was followed by a second sprinkling 24 hours later. The water retention capacity of the peat was best, and surface runoff lowest, with Sphagnum and Carex peat samples of humification grades H 2.5 6 in the moisture content class 56 75%. On account of the hydrophobicity of dry peat, runoff increased in a fairly regular manner with drying of the sample from 55% to 24 30%. Runoff from the samples with an original moisture content over 55% increased by 63% in the second round of sprinkling relative to the first, as they had practically reached saturation point on the first occasion, while those with an original moisture content below 55% retained their high runoff in the second round, due to continued hydrophobicity. The well-humified samples (H 6.5 8.5) with a moisture content over 80% showed a low water retention capacity and high runoff in both rounds of sprinkling. Loading of the runoff water with suspended solids, total phosphorus and total nitrogen, and also the chemical oxygen demand (CODMn O2), varied greatly in the sprinkling experiment, depending on the peat type and degree of humification, but concentrations of the same substances in the two sprinklings were closely or moderately closely correlated and these correlations were significant. The concentrations of suspended solids in the runoff water observed in the simulations of a peat production area and the direct surface runoff from it into the drainage ditch system in response to rain (sprinkling intensity 1.27 mm/min) varied c. 60-fold between the degrees of humification in the case of the Carex peats and c. 150-fold for the Sphagnum peats, while chemical oxygen demand varied c. 30-fold and c. 50-fold, respectively, total phosphorus c. 60-fold and c. 66-fold, total nitrogen c. 65-fold and c. 195-fold and ammonium nitrogen c. 90-fold and c. 30-fold. The increases in concentrations in the runoff water were very closely correlated with increases in humification of the peat. The correlations of the concentrations measured in extraction experiments (48 h) with peat type and degree of humification corresponded to those observed in the sprinkler experiments. The resulting figures for the surface runoff from a peat production area into the drainage ditches simulated by means of sprinkling and material concentrations in the runoff water were combined with statistics on the mean extent of daily rainfall (0 67 mm) during the frost-free period of the year (May October) over an observation period of 30 years to yield typical annual loading figures (kg/ha) for suspended solids (SS), chemical oxygen demand of organic matter (CODmn O2), total phosphorus (tot. P) and total nitrogen (tot. N) entering the ditches with respect to milled Carex (C) and Sphagnum (S) peats of humification grades H 2.5 8.5. In order to calculate the loading of drainage ditches from a milled peat production mire with the aid of these annual comparative values (in kg/ha), information is required on the properties of the intended production mire and its peat. Once data are available on the area of the mire, its peat depth, peat types and their degrees of humification, dry matter content, calorific value and corresponding energy content, it is possible to produce mutually comparable estimates for individual mires with respect to the annual loading of the drainage ditch system and the surrounding watercourse for the whole service life of the production area, the duration of this service life, determinations of energy content and the amount of loading per unit of energy generated (kg/MWh). In the 8 mires in the Köyhäjoki basin, Central Ostrobothnia, taken as an example, the loading of suspended solids (SS) in the drainage ditch networks calculated on the basis of the typical values obtained here and existing mire and peat data and expressed per unit of energy generated varied between the mires and horizons in the range 0.9 16.5 kg/MWh. One of the aims of this work was to develop means of making better use of existing mire and peat data and the results of corings and other field investigations. In this respect combination of the typical loading values (kg/ha) obtained here for S, SC, CS and C peats and the various degrees of humification (H 2.5 8.5) with the above mire and peat data by means of a computer program for the acquisition and handling of such data would enable all the information currently available and that deposited in the system in the future to be used for defining watercourse loading estimates for mires and comparing them with the corresponding estimates of energy content. The intention behind this work has been to respond to the challenge facing the energy generation industry to find larger peat production areas that exert less loading on the environment and to that facing the environmental authorities to improve the means available for estimating watercourse loading from peat production and its environmental impacts in advance. The results conform well to the initial hypothesis and to the goals laid down for the research and should enable watercourse loading from existing and planned peat production to be evaluated better in the future and the resulting impacts to be taken into account when planning land use and energy generation. The advance loading information available in this way would be of value in the selection of individual peat production areas, the planning of their exploitation, the introduction of water protection measures and the planning of loading inspections, in order to achieve controlled peat production that pays due attention to environmental considerations.

Computational Methods for Locating and Analyzing Conserved Gene Regulatory DNA Elements

This thesis presents methods for locating and analyzing cis-regulatory DNA elements involved with the regulation of gene expression in multicellular organisms. The regulation of gene expression is carried out by the combined effort of several transcription factor proteins collectively binding the DNA on the cis-regulatory elements. Only sparse knowledge of the 'genetic code' of these elements exists today. An automatic tool for discovery of putative cis-regulatory elements could help their experimental analysis, which would result in a more detailed view of the cis-regulatory element structure and function. We have developed a computational model for the evolutionary conservation of cis-regulatory elements. The elements are modeled as evolutionarily conserved clusters of sequence-specific transcription factor binding sites. We give an efficient dynamic programming algorithm that locates the putative cis-regulatory elements and scores them according to the conservation model. A notable proportion of the high-scoring DNA sequences show transcriptional enhancer activity in transgenic mouse embryos. The conservation model includes four parameters whose optimal values are estimated with simulated annealing. With good parameter values the model discriminates well between the DNA sequences with evolutionarily conserved cis-regulatory elements and the DNA sequences that have evolved neutrally. In further inquiry, the set of highest scoring putative cis-regulatory elements were found to be sensitive to small variations in the parameter values. The statistical significance of the putative cis-regulatory elements is estimated with the Two Component Extreme Value Distribution. The p-values grade the conservation of the cis-regulatory elements above the neutral expectation. The parameter values for the distribution are estimated by simulating the neutral DNA evolution. The conservation of the transcription factor binding sites can be used in the upstream analysis of regulatory interactions. This approach may provide mechanistic insight to the transcription level data from, e.g., microarray experiments. Here we give a method to predict shared transcriptional regulators for a set of co-expressed genes. The EEL (Enhancer Element Locator) software implements the method for locating putative cis-regulatory elements. The software facilitates both interactive use and distributed batch processing. We have used it to analyze the non-coding regions around all human genes with respect to the orthologous regions in various other species including mouse. The data from these genome-wide analyzes is stored in a relational database which is used in the publicly available web services for upstream analysis and visualization of the putative cis-regulatory elements in the human genome.

Marking one-summer old whitefish with fluorescent pigment spraying method and results of whitefish stockings in the Gulf of Bothnia

Anadromous whitefish is one of the most important fish species in the Finnish coastal fisheries in the Gulf fo Bothnia. To compensate the lost reproduction due to river damming and to support the fisheries, several million one-summer old whitefish are released yearly into the Gulf of Bothnia. Since there are naturally reproducing whitefish in the Gulf as well, and the wild and stocked fish can not be separated in the catch, stocking impact can only be estimated by marking the stocked fish. Due to the small size and large number of released whitefish, the scattered fishery and large area where the whitefish migrate, most of the traditionally used fish marking methods were either unsuitable (e.g. Carlin-tags) or proved to be too expensive (e.g. coded wire tags). Fluorescent pigment spraying method offers a fast and cost-effective method to mass-mark young fish. However, the results are not always satisfactory due to low long-time retention of the marks in some species. The method has to be tested and proper marking conditions and methods determined for each species. This thesis is based on work that was accomplished while developing the fluorescent pigment spraying method for marking one-summer old whitefish fingerlings, and it draws together the results of mass-marking whitefish fingerlings that were released in the Gulf of Bothnia. Fluorescent pigment spraying method is suitable for one-summer old whitefish larger than 8 cm total length. The water temperature during the marking should not exceed 10o C. Suitable spraying pressure is 6 bars measured in the compressor outlet, and the distance of the spraying gun nozzle should be ca 20 cm from the fish. Under such conditions, the marking results in long-term retention of the mark with low or no mortality. The stress level of the fish (measured as muscle water content) rises during the marking procedure, but if the fish are allowed to recover after marking, the overall stress level remains within the limits observed in normal fish handling during the capture-loading-transport-stocking procedure. The marked whitefish fingerlings are released into the sea at larger size and later in the season than the wild whitefish. However, the stocked individuals migrate to the southern feeding grounds in a similar pattern to the wild ones. The catch produced by whitefish stocking in the Gulf of Bothnia varied between released fingerling groups, but was within the limits reported elsewhere in Finland. The releases in the southern Bothnian Bay resulted in a larger catch than those made in the northern Bothnian Bay. The size of the released fingerlings seemed to have some effect on survival of the fish during the first winter in the sea. However, when the different marking groups were compared, the mean fingerling size was not related to stocking success.