The structure of Norway spruce (Picea abies [L.] Karst.) stems in relation to wood properties of sawn timber

An important challenge in forest industry is to get the appropriate raw material out from the forests to the wood processing industry. Growth and stem reconstruction simulators are therefore increasingly integrated in industrial conversion simulators, for linking the properties of wooden products to the three-dimensional structure of stems and their growing conditions. Static simulators predict the wood properties from stem dimensions at the end of a growth simulation period, whereas in dynamic approaches, the structural components, e.g. branches, are incremented along with the growth processes. The dynamic approach can be applied to stem reconstruction by predicting the three-dimensional stem structure from external tree variables (i.e. age, height) as a result of growth to the current state. In this study, a dynamic growth simulator, PipeQual, and a stem reconstruction simulator, RetroSTEM, are adapted to Norway spruce (Picea abies [L.] Karst.) to predict the three-dimensional structure of stems (tapers, branchiness, wood basic density) over time such that both simulators can be integrated in a sawing simulator. The parameterisation of the PipeQual and RetroSTEM simulators for Norway spruce relied on the theoretically based description of tree structure developing in the growth process and following certain conservative structural regularities while allowing for plasticity in the crown development. The crown expressed both regularity and plasticity in its development, as the vertical foliage density peaked regularly at about 5 m from the stem apex, varying below that with tree age and dominance position (Study I). Conservative stem structure was characterized in terms of (1) the pipe ratios between foliage mass and branch and stem cross-sectional areas at crown base, (2) the allometric relationship between foliage mass and crown length, (3) mean branch length relative to crown length and (4) form coefficients in branches and stem (Study II). The pipe ratio between branch and stem cross-sectional area at crown base, and mean branch length relative to the crown length may differ in trees before and after canopy closure, but the variation should be further analysed in stands of different ages and densities with varying site fertilities and climates. The predictions of the PipeQual and RetroSTEM simulators were evaluated by comparing the simulated values to measured ones (Study III, IV). Both simulators predicted stem taper and branch diameter at the individual tree level with a small bias. RetroSTEM predictions of wood density were accurate. For focusing on even more accurate predictions of stem diameters and branchiness along the stem, both simulators should be further improved by revising the following aspects in the simulators: the relationship between foliage and stem sapwood area in the upper stem, the error source in branch sizes, the crown base development and the height growth models in RetroSTEM. In Study V, the RetroSTEM simulator was integrated in the InnoSIM sawing simulator, and according to the pilot simulations, this turned out to be an efficient tool for readily producing stand scale information about stem sizes and structure when approximating the available assortments of wood products.

Variation in tracheid cross-sectional dimensions and wood viscoelasticity extent and control methods

Printing papers have been the main product of the Finnish paper industry. To improve properties and economy of printing papers, controlling of tracheid cross-sectional dimensions and wood viscoelasticity are examined in this study. Controlling is understood as any procedure which yields raw material classes with distinct properties and small internal variation. Tracheid cross-sectional dimensions, i.e., cell wall thickness and radial and tangential diameters can be controlled with methods such as sorting wood into pulpwood and sawmill chips, sorting of logs according to tree social status and fractionation of fibres. These control methods were analysed in this study with simulations, which were based on measured tracheid cross-sectional dimensions. A SilviScan device was used to measure the data set from five Norway spruce (Picea abies) and five Scots pine (Pinus sylvestris) trunks. The simulation results indicate that the sawmill chips and top pulpwood assortments have quite similar cross-sectional dimensions. Norway spruce and Scots pine are on average also relatively similar in their cross-sectional dimensions. The distributions of these species are somewhat different, but from a practical point of view, the differences are probably of minor importance. The controlling of tracheid cross-sectional dimensions can be done most efficiently with methods that can separate fibres into earlywood and latewood. Sorting of logs or partitioning of logs into juvenile and mature wood were markedly less efficient control methods than fractionation of fibres. Wood viscoelasticity affects energy consumption in mechanical pulping, and is thus an interesting control target when improving energy efficiency of the process. A literature study was made to evaluate the possibility of using viscoelasticity in controlling. The study indicates that there is considerable variation in viscoelastic properties within tree species, but unfortunately, the viscoelastic properties of important raw material lots such as top pulpwood or sawmill chips are not known. Viscoelastic properties of wood depend mainly on lignin, but also on microfibrillar angle, width of cellulose crystals and tracheid cross-sectional dimensions.

Structural analyses of (1->3),(1->4)-β-D-glucan of oats and barley

The structures of (1→3),(1→4)-β-D-glucans of oat bran, whole-grain oats and barley and processed foods were analysed. Various methods of hydrolysis of β-glucan, the content of insoluble fibre of whole grains of oats and barley and the solution behaviour of oat and barley β-glucans were studied. The isolated soluble β-glucans of oat bran and whole-grain oats and barley were hydrolysed with lichenase, an enzyme specific for (1→3),(1→4)-β-D-β-glucans. The amounts of oligosaccharides produced from bran were analysed with capillary electrophoresis and those from whole-grains with high-performance anion-exchange chromatography with pulse-amperometric detection. The main products were 3-O-β-cellobiosyl-D-glucose and 3-O-β-cellotriosyl-D-glucose, the oligosaccharides which have a degree of polymerisation denoted by DP3 and DP4. Small differences were detected between soluble and insoluble β-glucans and also between β-glucans of oats and barley. These differences can only be seen in the DP3:DP4 ratio which was higher for barley than for oat and also higher for insoluble than for soluble β-glucan. A greater proportion of barley β-glucan remained insoluble than of oat β-glucan. The molar masses of soluble β-glucans of oats and barley were the same as were those of insoluble β-glucans of oats and barley. To analyse the effects of cooking, baking, fermentation and drying, β-glucan was isolated from porridge, bread and fermentate and also from their starting materials. More β-glucan was released after cooking and less after baking. Drying decreased the extractability for bread and fermentate but increased it for porridge. Different hydrolysis methods of β-glucan were compared. Acid hydrolysis and the modified AOAC method gave similar results. The results of hydrolysis with lichenase gave higher recoveries than the other two. The combination of lichenase hydrolysis and high-performance anion-exchange chromatography with pulse-amperometric detection was found best for the analysis of β-glucan content. The content of insoluble fibre was higher for barley than for oats and the amount of β-glucan in the insoluble fibre fraction was higher for oats than for barley. The flow properties of both water and aqueous cuoxam solutions of oat and barley β-glucans were studied. Shear thinning was stronger for the water solutions of oat β-glucan than for barley β-glucan. In aqueous cuoxam shear thinning was not observed at the same concentration as in water but only with high concentration solutions. Then the viscosity of barley β-glucan was slightly higher than that of oat β-glucan. The oscillatory measurements showed that the crossover point of the G´ and G´´ curves was much lower for barley β-glucan than for oat β-glucan indicating a higher tendency towards solid-like behaviour for barley β-glucan than for oat β-glucan.

Consumers and the conceptual and practical appropriation of functional foods

Taking the appropriation of objects as a theoretical starting point, this study makes a distinction between a conceptual and practical level of adopting new objects and products in everyday life. The study applies the concept of appropriation in social food research and examines consumers appropriation of functional foods, i.e., foods developed to improve health and well-being or reduce the risk of disease beyond the usual nutritional effects of foods. The study uses the concept of appropriation to understand the adoption and the process of making functional foods our own . First, the study focuses on the conceptual appropriation by analysing consumers interpretations and opinions on functional foods. Second, it analyses the use of functional foods and examines the role of sociodemographic and food- and health-related background factors in the use of functional foods. Both quantitative and qualitative data were used in the study. Altogether 1210 Finns representative of the population took part in a survey carried out in 2002 as computer-assisted telephone interviews (CATI). The survey examined the acceptability and use of functional foods in Finland. In 2004, eight focus group discussions were organised for 45 users and non-users of cholesterol-lowering spreads. The qualitative study focused on consumers interpretative perspectives on healthy eating and functional foods. The findings are reported in four original articles and a summary article. The results show that the appropriation of functional foods is a multifaceted phenomenon. The conceptual appropriation is related to consumers interpretations of functional foods in the context of healthy foods and healthy eating; their trust in the products, their manufacturers, research and control; and the relationship of functional foods and the ideal of natural foods. The analysis of the practical appropriation of four different types of foods marketed as functional showed that there are sociodemographic differences between users and non-users of the products, but more importantly, the differences are related to consumers food- and health-related views and practices. Consumers ways of appropriating functional foods in the conceptual and practical sense take shape in a complex web of ideas and everyday practices concerning food, health and eating as a whole. The results also indicate that the conceptual and practical appropriation are not necessarily uniform or coherent processes. Consumers interpret healthy eating and functional foods from a variety of perspectives and there is a multiplicity of rationales of using functional foods. Appropriation embraces many opposing dimensions simultaneously: good experiences and doubts, approval and criticism, expectations and things taken for granted.

Synthesis, Reactivity and Biological Activity of 17β-HSD1 Inhibitors Based on a Thieno[2,3-d]pryrimidin-4(3H)-one Core

Breast cancer is the most common cancer in women in Western countries. In the early stages of development most breast cancers are hormone-dependent, and estrogens, especially estradiol, have a pivotal role in their development and progression. One approach to the treatment of hormone-dependent breast cancers is to block the formation of the active estrogens by inhibiting the action of the steroid metabolising enzymes. 17beta-Hydroxysteroid dehydrogenase type 1 (17beta-HSD1) is a key enzyme in the biosynthesis of estradiol, the most potent female sex hormone. The 17beta-HSD1 enzyme catalyses the final step and converts estrone into the biologically active estradiol. Blocking 17beta-HSD1 activity with a specific enzyme inhibitor could provide a means to reduce circulating and tumour estradiol levels and thus promote tumour regression. In recent years 17beta-HSD1 has been recognised as an important drug target. Some inhibitors of 17beta-HSD1 have been reported, however, there are no inhibitors on the market nor have clinical trials been announced. The majority of known 17beta-HSD1 inhibitors are based on steroidal structures, while relatively little has been reported on non-steroidal inhibitors. As compared with 17beta-HSD1 inhibitors based on steroidal structures, non-steroidal compounds could have advantages of synthetic accessibility, drug-likeness, selectivity and non-estrogenicity. This study describes the synthesis of large group of novel 17beta-HSD1 inhibitors based on a non-steroidal thieno[2,3-d]pyrimidin-4(3H)-one core. An efficient synthesis route was developed for the lead compound and subsequently employed in the synthesis of thieno[2,3-d]pyrimidin-4(3H)-one based molecule library. The biological activities and binding of these inhibitors to 17beta-HSD1 and, finally, the quantitative structure activity relationship (QSAR) model are also reported. In this study, several potent and selective 17beta-HSD1 inhibitors without estrogenic activity were identified. This establishment of a novel class of inhibitors is a progressive achievement in 17beta-HSD1 inhibitor development. Furthermore, the 3D-QSAR model, constructed on the basis of this study, offers a powerful tool for future 17beta-HSD1 inhibitor development. As part of the fundamental science underpinning this research, the chemical reactivity of fused (di)cycloalkeno thieno[2,3-d]pyrimidin-4(3H)-ones with electrophilic reagents, i.e. Vilsmeier reagent and dimethylformamide dimethylacetal, was investigated. These findings resulted in a revision of the reaction mechanism of Vilsmeier haloformylation and further contributed to understanding the chemical reactivity of this compound class. This study revealed that the reactivity is dependent upon a stereoelectronic effect arising from different ring conformations.

Atomic Layer Deposition and Photocatalytic Properties of Titanium Dioxide Thin Films

Photocatalytic TiO2 thin films can be highly useful in many environments and applications. They can be used as self-cleaning coatings on top of glass, tiles and steel to reduce the amount of fouling on these surfaces. Photocatalytic TiO2 surfaces have antimicrobial properties making them potentially useful in hospitals, bathrooms and many other places where microbes may cause problems. TiO2 photocatalysts can also be used to clean contaminated water and air. Photocatalytic oxidation and reduction reactions proceed on TiO2 surfaces under irradiation of UV light meaning that sunlight and even normal indoor lighting can be utilized. In order to improve the photocatalytic properties of TiO2 materials even further, various modification methods have been explored. Doping with elements such as nitrogen, sulfur and fluorine, and preparation of different kinds of composites are typical approaches that have been employed. Photocatalytic TiO2 nanotubes and other nanostructures are gaining interest as well. Atomic Layer Deposition (ALD) is a chemical gas phase thin film deposition method with strong roots in Finland. This unique modification of the common Chemical Vapor Deposition (CVD) method is based on alternate supply of precursor vapors to the substrate which forces the film growth reactions to proceed only on the surface in a highly controlled manner. ALD gives easy and accurate film thickness control, excellent large area uniformity and unparalleled conformality on complex shaped substrates. These characteristics have recently led to several breakthroughs in microelectronics, nanotechnology and many other areas. In this work, the utilization of ALD to prepare photocatalytic TiO2 thin films was studied in detail. Undoped as well as nitrogen, sulfur and fluorine doped TiO2 thin films were prepared and thoroughly characterized. ALD prepared undoped TiO2 films were shown to exhibit good photocatalytic activities. Of the studied dopants, sulfur and fluorine were identified as much better choices than nitrogen. Nanostructured TiO2 photocatalysts were prepared through template directed deposition on various complex shaped substrates by exploiting the good qualities of ALD. A clear enhancement in the photocatalytic activity was achieved with these nanostructures. Several new ALD processes were also developed in this work. TiO2 processes based on two new titanium precursors, Ti(OMe)4 and TiF4, were shown to exhibit saturative ALD-type of growth when water was used as the other precursor. In addition, TiS2 thin films were prepared for the first time by ALD using TiCl4 and H2S as precursors. Ti1-xNbxOy and Ti1-xTaxOy transparent conducting oxide films were prepared successfully by ALD and post-deposition annealing. Highly unusual, explosive crystallization behaviour occurred in these mixed oxides which resulted in anatase crystals with lateral dimensions over 1000 times the film thickness.

Parameters Affecting the Extraction of Polycyclic Aromatic Hydrocarbons with Pressurised Hot Water

Pressurised hot water extraction (PHWE) exploits the unique temperature-dependent solvent properties of water minimising the use of harmful organic solvents. Water is environmentally friendly, cheap and easily available extraction medium. The effects of temperature, pressure and extraction time in PHWE have often been studied, but here the emphasis was on other parameters important for the extraction, most notably the dimensions of the extraction vessel and the stability and solubility of the analytes to be extracted. Non-linear data analysis and self-organising maps were employed in the data analysis to obtain correlations between the parameters studied, recoveries and relative errors. First, pressurised hot water extraction (PHWE) was combined on-line with liquid chromatography-gas chromatography (LC-GC), and the system was applied to the extraction and analysis of polycyclic aromatic hydrocarbons (PAHs) in sediment. The method is of superior sensitivity compared with the traditional methods, and only a small 10 mg sample was required for analysis. The commercial extraction vessels were replaced by laboratory-made stainless steel vessels because of some problems that arose. The performance of the laboratory-made vessels was comparable to that of the commercial ones. In an investigation of the effect of thermal desorption in PHWE, it was found that at lower temperatures (200ºC and 250ºC) the effect of thermal desorption is smaller than the effect of the solvating property of hot water. At 300ºC, however, thermal desorption is the main mechanism. The effect of the geometry of the extraction vessel on recoveries was studied with five specially constructed extraction vessels. In addition to the extraction vessel geometry, the sediment packing style and the direction of water flow through the vessel were investigated. The geometry of the vessel was found to have only minor effect on the recoveries, and the same was true of the sediment packing style and the direction of water flow through the vessel. These are good results because these parameters do not have to be carefully optimised before the start of extractions. Liquid-liquid extraction (LLE) and solid-phase extraction (SPE) were compared as trapping techniques for PHWE. LLE was more robust than SPE and it provided better recoveries and repeatabilities than did SPE. Problems related to blocking of the Tenax trap and unrepeatable trapping of the analytes were encountered in SPE. Thus, although LLE is more labour intensive, it can be recommended over SPE. The stabilities of the PAHs in aqueous solutions were measured using a batch-type reaction vessel. Degradation was observed at 300ºC even with the shortest heating time. Ketones and quinones and other oxidation products were observed. Although the conditions of the stability studies differed considerably from the extraction conditions in PHWE, the results indicate that the risk of analyte degradation must be taken into account in PHWE. The aqueous solubilities of acenaphthene, anthracene and pyrene were measured, first below and then above the melting point of the analytes. Measurements below the melting point were made to check that the equipment was working, and the results were compared with those obtained earlier. Good agreement was found between the measured and literature values. A new saturation cell was constructed for the solubility measurements above the melting point of the analytes because the flow-through saturation cell could not be used above the melting point. An exponential relationship was found between the solubilities measured for pyrene and anthracene and temperature.

Holistic Spirituality in the Thinking of Ellen White

Spiritualiteetti viittaa syvälliseen, inhimilliseen ulottuvuuteen ja ominaisuuteen, jonka tarkka määritteleminen on haasteellista, ellei mahdotonta. Sitä vastaa yhtäältä uskonnollisuuden kautta toteutuva, elämän tarkoitukseen ja syvemmän olemuksen etsintään liittyvä hengellisyys, mutta toisaalta myös kaikkea muuta hengen viljelyä ja mielekkään olemisen tavoittelua tarkoittava henkisyys. John Swintonin mukaan hengen ulottuvuus on se inhimilliseen olemukseen kuuluva, dynaaminen elinvoima, joka virkistää ja elävöittää ihmistä ja motivoi häntä etsimään Jumalaa, arvoja, merkitystä, tarkoitusta ja toivoa. Tämä tutkimus nostaa tarkastelun kohteeksi kokonaisvaltaisen hengellisyyden, jolloin huomio kiinnitetään niihin sidoksiin, joiden kautta hengen ulottuvuus liittyy muihin inhimillisen elämän olennaisiin toimintoihin ja näkökulmiin. Tällaisia ovat 1) ajattelu 2) teot ja käytännön toiminta 3) suhteet ja vuorovaikutusverkostot 4) tunteet ja kanssakäymistä ohjaavat asenteet 5) olemassaolon ja olemisen ulottuvuudet. Kokemusten merkitys, arvo ja mielekkyys hahmottuvat juuri hengen alueella, toisin sanoen sisäisesti, hengellisenä ja henkisenä asiana. Tutkimusmateriaalina tässä tutkimuksessa on amerikkalaisen vuosina 1827 1915 eläneen Ellen Whiten kuusi myöhäiskauden teosta vuosilta 1892 1905 ja tutkimusmenetelmänä on käytetty systemaattista analyysiä. Olennaista Whiten tavassa käsitellä uskonnon harjoitukseen liittyviä aiheita on hänen käytännöllinen ja elämän arkeen kiinteästi niveltyvä otteensa. Tutkimus paljastaa, että Martti Lutherin käsitykset ovat merkittävästi vaikuttaneet Whiten ajatteluun. Lähteistä paljastuu samankaltaisuutta hänen näkemystensä ja uusimman suomalaisen Luther-tutkimuksen Martti Lutherin tuotannosta esiin nostaman ajattelutavan välillä. Vaikka teologisen oppineisuuden kannalta White ja Luther ovat eri tasoilla, kummankin käsitys ihmisen ja Jumalan välisen suhteen perusolemuksesta on samankaltainen: Lähtökohtana sille on Jumalan rakkaus ja hänen armostaan lähtenyt toiminta. Toiseksi, ihmisen ja Kristuksen välinen, olemuksellinen yhteys, unio , on perustana sille, että Jumala hyväksyy ihmisen ja huolehtii hänestä nyt ja ikuisesti. Kolmanneksi, tämä ihmisen ja Kristuksen liittoutuminen ja yhdistyminen ilmenee yhteistoimintana ja kumppanuutena yhteisten tavoitteiden saavuttamiseksi maailmassa. White korostaa ihmisen ja Kristuksen välisen hengellisen suhteen vuorovaikutteista ja toiminnallista luonnetta, joka tulee ilmi epäitsekkyytenä, toisten ihmisten ja heidän tarpeittensa huomioimisena sekä myötätuntona ja kykynä asettua toisen asemaan. Terveellistä elämäntapaa ja kasvatusta koskevat ajatuksensa White liittää siihen laaja-alaiseen näkemykseen hengellisyydestä, jonka tavoitteena on ihmisen kokonaisvaltainen hyvinvointi. Hän ei näe spiritualiteettia elämän arjesta irrallisena tai erillisenä saarekkeena, vaan ihmistä kaikessa ohjaavana, voimaannuttavana ja mielekkyyttä tuottavana, ensisijaisena ulottuvuutena. Tutkimuksen kuluessa myös Whiten usein käyttämät Jumalalle antautumisen ja luonteen käsitteet nousevat tarkastelun kohteiksi. Hänen mukaansa ihminen ei tahdonponnistuksillaan yksin pysty tavoittamaan Jumalaa vaan hänen on lakattava Jumalan rakastavan kutsun edessä itse tahtomasta ja suostuttava liittymään Jumalan tahtoon ja tarkoitukseen. Tämä liittyy siihen sisäiseen muutokseen, jota White kuvaa luonteen käsitteen avulla. Jumalan armon vaikuttama tahdon uudelleen suuntaaminen muuttaa ihmisen olemusta, arvoja, asennoitumisen tapaa ja myötätuntoisen vuorovaikutuksen kykyä niin ettei ihminen ole enää aivan sama kuin ennen. Kysymys on toisaalta yhtäkkisestä ja kertakaikkisesta olemuksellisesta muuttumisesta, mutta samalla myös hiljaisesta, elämänmittaisesta kasvusta ja kypsymisestä. Juuri luonteen käsitteen avulla White kuvaa hengellisyyttä ja siihen kuuluvaa sisästä matkaa. Tässä tutkimuksessa spiritualiteettia lähestytään yleisinhimillisenä piirteenä ja ominaisuutena, jolloin huomio ei ole ensisijaisesti yksittäisissä opillisissa käsityksissä tai uskonnollisuuden harjoittamisen muodoissa. Tarkoituksena on luoda kokoava rakenne, jonka puitteissa holistinen spiritualiteetti voidaan selkeämmin hahmottaa ja yksilöidymmin ymmärtää.

Ethics of Justification : A Defence of Contractualism

In What We Owe to Each Other, T.M. Scanlon formulated a new version of the ethical theory called contractualism. This theory took reasons considerations that count in favour of judgment-sensitive attitudes to be the fundamental normative notion. It then used normative reasons to first account for evaluative properties. For an object to be valuable, on this view, is for it to have properties that provide reasons to have favourable attitudes towards the bearer of value. Scanlon also used reasons to account for moral wrongness. His contractualism claims that an act is morally wrong if it is forbidden by any set of moral principles that no one could reasonably reject. My thesis consists of five previously published articles which attempt to clarify Scanlon s theory and to defend it against its critics. The first article defends the idea that normative reason-relations are fundamental against Joshua Gert. Gert argues that rationality is a more basic notion than reasons and that reasons can be analysed in terms of their rationally requiring and justifying dimensions. The second article explores the relationship between value and reasons. It defends Scanlon s view according to which reasons are the more basic than value against those who think that reasons are based on the evaluative realm. The last three articles defend Scanlon s views about moral wrongness. The first one of them discusses a classic objection to contractualist theories. This objection is that principles which no one could reasonably reject are redundant in accounting for wrongness. This is because we need a prior notion of wrongness to select those principles and because such principles are not required to make actions wrong or to provide reasons against wrong actions. The fourth article explores the distinctive reasons which contractualists claim there are for avoiding the wrong actions. The last article argues against the critics of contractualism who claim that contractualism has implausible normative consequences for situations related to the treatment of different-sized groups of people.

Political transition and structural politicisation : The long shadow of Taiwan's one-party legacy

Väitöskirjatutkimuksessa tarkastellaan Taiwanin politiikkaa ensimmäisen vaalien kautta tapahtuneen vallanvaihdon jälkeen (2000) yhteiskunnan rakenteellisen politisoitumisen näkökulmasta. Koska Taiwanilla siirryttiin verettömästi autoritaarisesta yksipuoluejärjestelmästä monipuoluejärjestelmään sitä on pidetty poliittisen muodonmuutoksen mallioppilaana. Aiempi optimismi Taiwanin demokratisoitumisen suhteen on sittemmin vaihtunut pessimismiin, pitkälti yhteiskunnan voimakkaasta politisoitumisesta johtuen. Tutkimuksessa haetaan selitystä tälle politisoitumiselle. Yhteiskunnan rakenteellisella politisoitumisella tarkoitetaan tilannetta, jossa ”poliittisen” alue kasvaa varsinaisia poliittisia instituutioita laajemmaksi. Rakenteellinen politisoituminen muuttuu helposti yhteiskunnalliseksi ongelmaksi, koska siitä usein seuraa normaalin poliittisen toiminnan (esim. lainsäädännän) jähmettyminen, yhteiskunnan jyrkkä jakautuminen, alhainen kynnys poliittisille konflikteille ja yleisen yhteiskunnallisen luottamuksen alentuminen. Toisin kuin esimerkiksi Itä-Euroopassa, Taiwanissa entinen valtapuolue ei romahtanut poliittisen avautumisen myötä vaan säilytti vahvan rakenteellisen asemansa. Kun valta vaihtui ensimmäisen kerran vaalien kautta, vanha valtapuolue ei ollut valmis luovuttamaan poliittisen järjestelmän ohjaksia käsistään. Alkoi vuosia kestänyt taistelu järjestelmän hallinnasta vanhan ja uuden valtapuolueen välillä, jossa yhteiskunta politisoitui voimakkaasti. Tutkimuksessa Taiwanin yhteiskunnan politisoituminen selitetään useiden rakenteellisten piirteiden yhteisvaikutuksen tuloksena. Tällaisia politisoitumista edistäviä rakentellisia piirteitä ovat hidas poliittinen muutos, joka säilytti vanhat poliittiset jakolinjat ja niihin liittyvät vahvat edut ja intressit; sopimaton perustuslaki; Taiwanin epäselvä kansainvälinen asema ja jakautunut identiteetti; sekä sosiaalinen rakenne, joka helpottaa ihmisten nopeaa mobilisointia poliittiisiin mielenilmauksiin. Tutkimuksessa kiinnitetään huomiota toistaiseksi vähän tutkittuun poliittiseen ilmiöön, joidenkin demokratisoituvien yhteiskuntien voimakkaaseen rakenteelliseen politisoitumiseen. Tutkimuksen pääasiallinen havainto on, että yksipuoluejärjestelmän demokratisoituminen kantaa sisällään rakenteellisen politisoitumisen siemenen, jos entinen valtapuolue ei romahda demokratisoitumisen myötä.