Comparison of firmness meters for measuring ‘Hass’ avocado fruit firmness

The temporal passage of fruit through the supply chain and the selection of consumable fruit by shoppers depend primarily upon fruit firmness. Traditionally, fruit firmness measuring methods, like Effegi and conical probes, are relatively inefficient and destructive. Simple, accurate and non-damaging methods of measuring fruit firmness are ideally required to help assure eating quality to the consumer without fruit wastage. The firmness of 'Hass' avocado fruit at a range of ripening stages was measured with the various different firmness measuring techniques of the Sinclair iQ Firmness Tester (SIQFT), the Electronic Firmometer (EF), the Analogue Firmness Meter (AFM) and hand squeezing. Measurements were made by each method at different points on the same fruit. Destructive bruise assessment was performed 48 h later, thereby allowing sufficient time for fruit to express any bruising resulting from the act of firmness measurements. Non-linear relationships were determined between fruit firmness values measured with the different techniques. The adjusted R2 for the relationship between the SIQFT and the EF was 91.6%. For the SIQFT and the AFM, the adjusted R2 was 73.7%. It was 77.7% for the SIQFT and hand squeezing. A significantly (P<0.05) high incidence of bruising was associated with firmness assessment by the EF as compared with either the SIQFT or the AFM. Among the methods compared, the SIQFT was non-damaging compared with the EF and relatively efficient for measuring the firmness. This instrument merits consideration as a quality control tool of choice in 'Hass' avocado supply chains.

1-Methylcyclopropene Delays Softening in Tomato Slices

I-Methylcyclopropene (1-MCP) has the potential in tomato to reduce ethylene-associated changes in texture. Tomato cv. 'Revolution' was harvested at the 'pink' maturity stage and whole fruit treated with 0, 0.1, 1.0 or 10.0 µL.L-' 1-MCP at 20 "C for 12 h. Slices of 7-mm thickness were cut using a commercial slicer, and the slices stored in vertical stacks in plastic containers at 5°C for 7 days. The application of 1-MCP reduced both ethylene production and respiration rate of slices and resulted in firmer pericarp firmness. Ethylene production was 24%, 40%, and 62% lower following 0.1, 1.0, 10.0 µL L-' 1-MCP, respectively, compared with controls. In addition, respiration rate was reduced 6%, 10% and 20% by those 1-MCP treatments. 1-MCP treatments produced 20%, 34%, and 24% higher pericarp firmness, respectively, than in fruit not treated with 1-MCP.

Exposure of Tomato Fruit to 1-MCP Improves Quality of Stored Slices

Maintenance of quality, such as firmness, is important during storage of fresh cut produce. This study compared the effects of I-MCP on the quality of tomato slices when intact tomatoes were treated with 1-MCP and then sliced, or tomatoes were sliced and the slices treated with I-MCP. In both instances the MCP treatment was 1 µL Lˉٰ at 20 ºC for 12 h. Tomato cv. 'Revolution' was harvested at the 'pink' stage of maturity, cut into 7-mm slices, and stored as vertical stacks in closed plastic containers at 5ºC for up to 7 days after the 1-MCP treatment. Exposure of intact tomatoes to I-MCP resulted in reduced ethylene production (31%) and firmer (22%) slices than when tomatoes were not I-MCP treated. The application of I-MCP prior to slicing of tomatoes appears a useful strategy to retain quality of stored tomato slices.

The impact of dry matter, ripeness and internal defects on consumer perceptions of avocado quality and intentions to purchase.

Insights into the relative importance of various aspects of product quality can be provided through quantitative analysis of consumer preference and choice of fruit. In this study, methods previously used to establish taste preferences for kiwifruit (Harker et al., 2008) and conjoint approaches were used to determine the influence of three key aspects of avocado quality on consumer liking and willingness to purchase fruit: dry matter percentage (DM), level of ripeness (firmness) and internal defects (bruising). One hundred and seven consumers tasted avocados with a range of DM levels from ~20% (minimally mature) to nearly 40% (very mature), and at a range of fruit firmness (ripeness) stages (firm-ripe to soft-ripe). Responses to bruising, a common quality defect in fruit obtained from the retail shelf, were examined using a conjoint approach in which consumers were presented with photographs showing fruit affected by damage of varying severity. In terms of DM, consumers showed a progressive increase in liking and intent to buy avocados as the DM increased. In terms of ripeness, liking and purchase intent was higher in avocados that had softened to a firmness of 6.5 N or below (hand-rating 5). For internal defects, conjoint analysis revealed that price, level of bruising and incidence of bruising all significantly lowered consumers' future purchase decision, but the latter two factors had a greater impact than price. These results indicate the usefulness of the methodology, and also provide realistic targets for Hass avocado quality on the retail shelf.

The Application of Near Infrared Spectroscopy for the Assessment of Avocado Quality Attributes, Infrared Spectroscopy. Chapter 14

Quality and safety evaluation of agricultural products has become an increasingly important consideration in market/commercial viability and systems for such evaluations are now demanded by customers, including distributors and retailers. Unfortunately, most horticultural products struggle with delivering adequate and consistent quality to the consumer. Removing inconsistencies and providing what the consumer expects is a key factor for retaining and expanding both domestic and international markets. Most commercial quality classification systems for fruit and vegetables are based on external features of the product, for example: shape, colour, size, weight and blemishes. However, the external appearance of most fruit is generally not an accurate guide to the internal or eating quality of the fruit. Internal quality of fruit is currently subjectively judged on attributes such as volatiles, firmness, and appearance. Destructive subjective measures such as internal flesh colour, or objective measures such as extraction of juice to measure sweetness (oBrix) or assessment of dry matter (DM) content are also used, although obviously not for every fruit – just a sample to represent the whole consignment. For avocado fruit, external colour is not a maturity characteristic, and its smell is too weak and appears later in its maturity stage (Gaete-Garreton et al., 2005). Since maturity is a major component of avocado quality and palatability, it is important to harvest mature fruit, so as to ensure that fruit will ripen properly and have acceptable eating quality. Currently, commercial avocado maturity estimation is based on destructive assessment of the %DM, and sometimes percent oil, both of which are highly correlated with maturity (Clark et al., 2003; Mizrach & Flitsanov, 1999). Avocados Australia Limited (AAL (2008)) recommend a minimum maturity standard for its growers of 23 %DM (greater than 10% oil content) for the ‘Hass’ cultivar, although consumer studies indicate a preference for at least 25 %DM (Harker et al., 2007).

Impact Induced Bruising in Ripening ‘Hass’ Avocado Fruit

This article describes the relationship between avocado fruit firmness, level of impact energy absorbed by the fruit, and post impact fruit holding duration with the incidence of bruising.

Continuous combined microwave and hot air treatment of apples for fruit fly (Bactrocera tryoni and B. jarvisi) disinfestation

Apples at 24 ± 2 °C were heated in a pilot scale hot air assisted (40 °C) continuous pentagonal microwave system, to evaluate the effectiveness of this treatment on insect mortality (variety Mutsu) and fruit quality (variety Granny Smith). An average temperature of 53.4 ± 1.3 °C at core, bottom and flesh of the apple was recorded at the end of the treatment. One hundred percent mortality of the most tolerant stage of Queensland fruit fly (Bactrocera tryoni, Froggatt) and Jarvis's fruit fly (Bactrocera jarvisi, Tryon), were observed when the Mortality value (M52, equivalent time of isothermal treatment at 52 °C) at the slowest heating point applicable for each experiment was ≥ 50 min and ≥ 37 min, respectively. Results showed that microwave heat treatment is effective for insect disinfestation without any adverse impact on total soluble solids, flesh or peel firmness of the treated apples. The treated apples recorded a significantly higher pH and lower ion leakage than the untreated apples after 3 or 4 weeks. Therefore, the microwave heat treatment has the potential to be developed as an alternative chemical free quarantine treatment against economically significant insect pests. Industrial relevance Hot air assisted microwave heating of fruits and vegetables, is more cost effective compared to vapour heat treatment and ionising radiation for disinfestation of insects. Microwave treatment is environmentally friendly compared to fumigation and chemical treatments. Hot air assisted microwave disinfestation can be performed at farms or centralised pack houses since the capital cost would be comparatively lower than vapour heat or ionising radiation treatments.

Impact of 1-methylcyclopropene treatment on the sensory quality of 'Bartlett' pear fruit

The ethylene biosynthesis inhibitor, 1-methylcyclopropene (1-MCP), has been commercially used to extend the storage life of European pear fruit and to allow shipment to distant markets. However, the influence of 1-MCP on the ability of fruit to ripen to an acceptable sensory quality has not been investigated in 'Bartlett' pear, one of the most aromatic of pear fruit. In the current study, early-, mid- and late-season 'Bartlett' pear fruit were treated with 0.6μLL-1 1-MCP at 0°C for 24h, 100μLL-1 ethylene at 20°C for 24h, or untreated before immediate transfer to 20°C for ripening until eating soft (13N firmness). Fruit from each treatment were subjected to objective and sensory quality evaluation once ripe. Sensory quality showed differences related to harvest maturity; the importance of harvest maturity depended on the treatment. Treatment with 1-MCP effectively slowed fruit ripening and therefore extended postharvest life, but also resulted in fully ripened pears with more desirable sensory traits, as compared with ethylene-treated and untreated pears. The enhanced sensory quality was related to higher sweetness, juiciness and pear aroma and reduced fermented aroma, gritty texture and tart taste. In addition, the sensory profiles of 1-MCP-treated pears were more stable among fruit from the three harvest dates than the ethylene-treated pears, which exhibited very different sensory profiles between early- and late-season fruits. © 2015 Elsevier B.V.

Uses of an innovative ethylene-α-cyclodextrin inclusion complex powder for ripening of mango fruit

A novel ethylene-α-cyclodextrin (α-CD) inclusion complex (IC) powder was investigated to ripen Calypso mango fruit. Modulated release of ethylene gas from the IC powder was achieved by admixture with deliquescent salt CaCl2 at RHs of 75.5% and 93.6%. The IC powder was tested in the laboratory and for in-transit ripening of mango fruit over two seasons. In the laboratory experiment, ethylene gas started to release from the IC powder in 2 h and complete release was achieved in 24 h. Assessments of fruit colour and firmness showed that encapsulated ethylene and commercial grade ethylene from pressurised cylinder similarly shortened the ripening time to 9–10 days (after harvest) for treated fruit as compared with 15 days for untreated mango. Mango fruit treated in both ways with ethylene showed more uniform ripening than the control. For the in-transit ripening using the IC powder, ethylene was found to be between 4.9 and 10.5 μL L−1 in the headspace of the truck containers over 48 h. Mango fruit from the treated containers shortened the ripening time by 3–6 days as compared to the untreated control fruit. Thus, the safe and convenient IC powder has demonstrated promise for in-transit fruit ripening.

Low-dose methyl bromide fumigation as a quarantine disinfestation treatment for nectarines against Queensland fruit fly (Diptera:Tephritidae)

White nectarines (Prunus persica var. nucipersica) were fumigated with methyl bromide (MB) at a nominal treatment dose of 18 g m-3 at 18°C for 5 h and 30 min as a quarantine disinfestation treatment against Bactrocera tryoni, the Queensland fruit fly. Three large scale trials were conducted against each of the four immature lifestages, eggs and first, second and third instars. There were no survivors from the estimated 43,614 eggs, 41,873 first instars, 41,345 second instars and 33,549 third instars treated, thereby resulting in an efficacy of GROTERDAN99.99% mortality at the 95% confidence level for each lifestage. Of the 12 trials reported herein, the highest concentration of MB, sampled from the chamber headspace analysed by gas chromatography, was 18.7 g m-3. The maximum chamber temperature from 5 min readings was 19.7°C and the maximum fruit core temperature was 19.5°C. The treatment time for all trials was exactly 5.5 h. Thus the recommended treatment dose to disinfest nectarines from B. tryoni is 19.0 g m-3 MB at 20.0°C for 5.5 h. Fruit quality trials were conducted on white nectarines at three combinations of treatment parameters: 15 g m-3 MB at 19°C for 5.25 h; 18 g m-3 MB at 19°C for 5.5 h and 21 g m-3 MB at 19°C for 5.5 h. The fruit were stored at 0, 4 and 8 days at 4°C and 8 days at 4°C followed by 4 d at 22°C. They were then were assessed for skin colour, flesh colour, skin defects, flesh defects, fruit weight loss, flesh firmness, total soluble solids, titratable acidity and rots. There was no significant difference between untreated control and MB treated fruits in any of the parameters measured. Thus the treatments did not have adverse effects on fruit quality.

Postharvest light treatments increase skin blush in mango fruit

Skin colour is an important quality parameter that influences mango fruit marketability. The mango industry is interested in controlled induction of skin blush in mangoes. It is desirable to understand the control of anthocyanin accumulation in mango skin. Among environmental factors known to induce anthocyanin accumulation in plants, light is the most studied. Light exposure induces pigmentation in various fruits, including apple, strawberry and grape. The effect of different light qualities on skin blush in mango fruit has received relatively little attention. The objective of this study was to assess anthocyanin accumulation and blush in response to blue, red and far red light from light-emitting diodes (LEDs) as applied to harvested mango fruit skin during storage at 12°C. Except for red light, the other wavelengths induced anthocyanin accumulation and skin blush as compared to the dark control treatment. Anthocyanin concentration and a∗ values were highest in blue light exposed fruit skin. This wavelength enhanced phenylalanine ammonia lyase activity in the mango skin, which may be associated with increased pigmentation. LED light treatment did not affect other fruit quality parameters at 21 days of storage, including firmness, total soluble solids and titratable acidity. Overall, the findings suggest that postharvest treatment with blue light can induce skin blush in mango fruit, which potentially may enhance their commercial value.

Production locality influences postharvest disease development and quality in mangoes

Postharvest disease management is one of the key challenges in commercial mango supply chains. Comprehensive investigations were made regarding the impact of geographic locality on postharvest disease development and other quality parameters in 'Sindhri' and 'Samar Bahisht (S.B.) Chaunsa' mangoes under ambient (33±1°C; 55-60% RH) and low temperature storage/simulated shipping (12±1°C; 80- 85% RH) conditions (28 or 35 days storage for 'Sindhri' and 21 or 28 days for 'S.B. Chaunsa'). Physiologically mature (days from fruit set were 95-100 and 110-115 for 'Sindhri' and 'S.B Chaunsa', respectively) 'Sindhri' and 'S.B. Chaunsa' fruits were harvested from five geographic localities and subjected to ambient and simulated shipping conditions. Under ambient conditions, no disease incidence was observed till fruit eating stage in 'Sindhri'. However, in 'S.B. Chaunsa', significant variation in different localities was observed with respect to disease incidence. Maximum and at par disease was exhibited by the fruit collected from district Vehari and Khanewal in 'S.B. Chaunsa'. Under simulated shipping conditions, disease development varied significantly with respect to different locations and storage durations. In 'Sindhri', fruit of M. Garh, while, 'S.B. Chaunsa' fruit of districts R.Y. Khan, M. Garh and Khanewal showed higher disease incidence. Fruit peel colour development was significantly reduced as storage days increased. Fruit firmness, skin shriveling, fresh weight loss, dry matter, biochemical and organoleptic attributes also varied significantly among the fruit sourced from different orchards of different localities. Analysis of N contents in leaves and fruit peel revealed that N contents of leaf and peel were positively correlated with disease severity in mango. Botryodiplodia spp., Phomopsis mangiferae, Alternaria alternata, Colletotrichum gloeosporioides were the pathogens isolated from fruits of all locations; however, the prevalence frequency varied with the geographic localities. In conclusion, the production locality, cultivar and nutrition (nitrogen content of fruit peel) had significant effect on fruit quality out-turn at ripe stage in terms of disease development so area specific disease management system needs to be implemented for better quality at retail.