Processing small diameter logs from sub-tropical species

Small spindleless veneer lathe technology was used to produce veneer sheets as an alternative processing option to optimise the use of small log plantation resource. Thinned (300 spha) and unthinned control (1000 spha) plantings of 10.5-year-old Corymbia citriodora ssp. variegata (CCV) and E. dunnii (Dunn’s white gum) grown in two contrasting sites from climatic regions with large annual rainfall differences were studied. Overall veneer gross recoveries ranged from 50% to 70%, which were up to 3 times higher than typical sawn green-off saw recoveries from small plantation hardwood logs of similar diameter. Major limiting factors preventing veneer from meeting higher grades were the presence of kino defects and encased knots. Splits in E. dunnii veneer also contributed to reduced grade quality. Differences between two thinning treatments for veneer properties and grade recovery were generally small. There was significant evidence of site and species differences on veneer quality. The good quality site with higher rainfall in northern New South Wales produced denser and stiffer veneers with higher grade recoveries. CCV is a superior structural veneer species with high wood density and hardness as well as very good veneer stiffness exceeding 15,000 MPa but Dunn’s white gum has also demonstrated good potential as a useful structural plywood resource. Results indicate that relatively high veneer recoveries were achieved for the sub-tropical plantation hardwoods combined with very superior mechanical properties which suggest that veneer production have suitable attributes for a range of engineered wood products including plywood and laminated veneer lumber.

Handling of Two Tropical Australian Sharks to Improve Quality and to Identify the Cause of Tough Texture

Sharks caught in tropical Australian waters occasionally exhibit tough texture. Two species of Carcharinid shark, originally known as the sorrah shark (Carcharinus sorrah) and the black spot shark (Carcharinus tilstoni), compose the majority of the catch. Experiments were conducted to identify the cause of tough texture and to improve the overall quality of the catch. The possibility that a cold shock reaction may occur was investigated by observing the contraction of fillets under a range of temperature conditions before freezing. The effect of on-board handling practices were evaluated using frozen shark fillets, which had been stored prior to freezing in refrigerated seawater at different rigor stages, temperatures and times as trunks. Fillets were analyzed for nucleotides, lactate, thaw pH, sarcomere length and raw and cooked shear force values. The existence of thaw rigor was also investigated. There was little difference in the texture between the individual strips of a fillet exposed to different temperatures but there were significant differences between individual sharks. A cold shock reaction could not be demonstrated in these species. The main influences on texture were of biological origin. The species, sex and size were found to have significant links with texture of fillets. The quality of the fillets deteriorated quicker during the warmer season and were at their worst if the trunks were kept on deck till post-rigor or held in 15 degree C refrigerated seawater before freezing

Ginger (Zingiber officinale) autotetraploids with improved processing quality produced by an in vitro colchicine treatment

Ginger autotetraploids were produced by immersing shoot tips in a 0.5% w/v colchicine, 2% v/v dimethyl sulfoxide solution for 2 h. Stomatal measurements were used as an early indicator of ploidy differences in culture with mean stomata length of tetraploids (49.2 μm) being significantly larger than the diploid (38.8 µm). Of the 500 shoot tips treated, 2% were characterised as stable autotetraploid lines following field evaluation over several seasons. Results were confirmed with flow cytometry and, of the 7 lines evaluated for distinctness and uniformity, 6 were solid tetraploid mutants and 1 was a periclinal chimera. Significant differences were noted between individual tetraploid lines in terms of shoot length, leaf length, leaf width, size of rhizome sections (knob weight) and fibre content. The solid autotetraploid lines had significantly wider, greener leaves than the diploids, they had significantly fewer but thicker shoots and, although ‘Queensland’ (the diploid parent from which the tetraploids were derived) had a greater total rhizome mass at harvest, its knob size was significantly smaller. From the autotetraploid lines, one line was selected for commercial release as ‘Buderim Gold’. It compared the most favourably with ‘Queensland’ in terms of the aroma/flavour profile and fibre content at early harvest, and had consistently good rhizome yield. More importantly it produced large rhizome sections, resulting in a higher recovery of premium grade confectionery ginger and a more attractive fresh market product.

Timing of weaning and processing: effects on liveweight changes of weaner cattle

To reduce the number of musters and handling costs, calves in extensive cattle herds in northern Australia are processed (vaccinated, ear-marked, de-horned, branded and males castrated) shortly after they are weaned. As stress has adverse effects on health and growth, and weaning is a stressful time for calves, this experiment asked if calf health, welfare and performance were improved when calves had a period with their mothers post-processing, before they were weaned.

Aseptic Processing of Foods Containing Particulates

Aseptic processing involves sterilising the product and package separately, and filling under sterile conditions. Advantages include better product quality compared with canned products, lower transport and storage costs compared with frozen products, and virtually no restriction on package size. Problems include ensuring adequate heat penetration into the particles to ensure sterility, preventing separation of particles from the carrier liquid, and retention of particle structure and shape. Particulate foods can be sterilised in scraped - surface heat exchangers. Other methods involve heating the particles separately, and combining them during filling. Projects will commence at the International Food Institute of Queensland (IFIQ) on aseptic packaging of a meat and vegetable product, and aseptically packaged mango pieces.

Aseptic Processing of Meat Products

Aseptic processing involves sterilising the product (most meat products being low-acid foods containing particulates) and package separately, and filling under sterile conditions. Advantages include better product quality compared with canned products, lower transport and storage costs compared with frozen products, and virtually no restriction on package size. Problems include ensuring adequate heat penetration into the particles to ensure sterility, preventing separation of particles from the carrier liquid, and retention of particle structure and shape. Particulate foods can be sterilised in scraped-surface heat exchangers. Other methods involve heating the particles separately, and combining them during filling. The effects of aseptic processing on meat product quality (colour, flavour, texture, and mutrition) are outlined in this paper.

Rockmelon Processing Quality

Considerable export opportunities exist in countries such as Japan, Canada, and Europe (Germany) for peeled rockmelon frozen in quarters or as diced product. Processing of these products is limited because the cost of hand labour for peeling is prohibitive. Consequently, development of mechnanical peeling equipment is essential for Australian industry to compete. In this project, appropriate machinery for the production of a high quality product is being developed, and basic studies in food technology, marketing, and production are being carried out. There are no Australian publications on rockmelon freezing, although fresh fruit quality of various cultivars has been investigated (Mutton, 1978). Very little overseas information on freezing rockmelons has been published (del Rio and Miller, 1979 and Martinez-Javega et al., 1975). In this project, the freezing quality of new rockmnelon and honeydew melon cultivars was evaluated.

Time-dependent instantaneous mortality rates from multiple tagging experiments with exact times of release and recovery

Instantaneous natural mortality rates and a nonparametric hunting mortality function are estimated from a multiple-year tagging experiment with arbitrary, time-dependent fishing or hunting mortality. Our theory allows animals to be tagged over a range of times in each year, and to take time to mix into the population. Animals are recovered by hunting or fishing, and death events from natural causes occur but are not observed. We combine a long-standing approach based on yearly totals, described by Brownie et al. (1985, Statistical Inference from Band Recovery Data: A Handbook, Second edition, United States Fish and Wildlife Service, Washington, Resource Publication, 156), with an exact-time-of-recovery approach originated by Hearn, Sandland and Hampton (1987, Journal du Conseil International pour l'Exploration de la Mer, 43, 107-117), who modeled times at liberty without regard to time of tagging. Our model allows for exact times of release and recovery, incomplete reporting of recoveries, and potential tag shedding. We apply our methods to data on the heavily exploited southern bluefin tuna (Thunnus maccoyii).

Use of part records in Merino breeding programs - The inheritance of wool growth and fibre traits during different times of the year to determine their value in Merino breeding programs

Fibre diameter can vary dramatically along a wool staple, especially in the Mediterranean environment of southern Australia with its dry summers and abundance of green feed in spring. Other research results have shown a very low phenotypic correlation between fibre diameter grown between seasons. Many breeders use short staples to measure fibre diameter for breeding purposes and also to promote animals for sale. The effectiveness of this practice is determined by the relative response to selection by measuring fibre traits on a full 12 months wool staple as compared to measuring them only on part of a staple. If a high genetic correlation exists between the part record and the full record, then using part records may be acceptable to identify genetically superior animals. No information is available on the effectiveness of part records. This paper investigated whether wool growth and fibre diameter traits of Merino wool grown at different times of the year in a Mediterranean environment, are genetically the same trait, respectively. The work was carried out on about 7 dyebanded wool sections/animal.year, on ewes from weaning to hogget age, in the Katanning Merino resource flocks over 6 years. Relative clean wool growth of the different sections had very low heritability estimates of less than 0.10, and they were phenotypically and genetically poorly correlated with 6 or 12 months wool growth. This indicates that part record measurement of clean wool growth of these sections will be ineffective as indirect selection criteria to improve wool growth genetically. Staple length growth as measured by the length between dyebands, would be more effective with heritability estimates of between 0.20 and 0.30. However, these measurements were shown to have a low genetic correlation with wool grown for 12 months which implies that these staple length measurements would only be half as efficient as the wool weight for 6 or 12 months to improve total clean wool weight. Heritability estimates of fibre diameter, coefficient of variation of fibre diameter and fibre curvature were relatively high and were genetically and phenotypically highly correlated across sections. High positive phenotypic and genetic correlations were also found between fibre diameter, coefficient of variation of fibre diameter and fibre curvature of the different sections and similar measurements for wool grown over 6 or 12 months. Coefficient of variation of fibre diameter of the sections also had a moderate negative phenotypic and genetic correlation with staple strength of wool staples grown over 6 months indicating that coefficient of variation of fibre diameter of any section would be as good an indirect selection criterion to improve stable strength as coefficient of variation of fibre diameter for wool grown over 6 or 12 months. The results indicate that fibre diameter, coefficient of variation of fibre diameter and fibre curvature of wool grown over short periods of time have virtually the same heritability as that of wool grown over 12 months, and that the genetic correlation between fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part and on full records is very high (rg > 0.85). This indicates that fibre diameter, coefficient of variation of fibre diameter and fibre curvature on part records can be used as selection criteria to improve these traits. However, part records of greasy and clean wool growth would be much less efficient than fleece weight for wool grown over 6 or 12 months because of the low heritability of part records and the low genetic correlation between these traits on part records and on wool grown for 12 months.

Cocowood processing manual: from coconut wood to quality flooring.

This manual describes best practice for producing high-value flooring products from coconut ‘wood’—or cocowood. It meets international standards for flooring products and accounts for the recognised, specific, local conditions of the Pacific Islands. The information is intended for operators skilled in timber processing, who need to work with the unusual properties of cocowood, and specifies where cocowood processes differ from standard practice for timber. For other processes, refer to the relevant standards set by the importing country. These technical guidelines are based on the research outcomes of the ACIAR project, 'Improving value and marketability of coconut wood'. The manual is divided into three chapters. Each chapter adds to different aspects of primary and secondary processing. Chapter 1 provides an overview of the best practice steps for harvesting and processing cocowood. There is also a glossary of terms specifically associated with processing cocowood and a section on managing processing risks. Chapter 2 covers cocowood’s unique properties and how they relate to critical processing techniques. This is followed by sections that set out the processing methods in more detail, explaining why these practices are essential when working with cocowood. Chapter 3 provides more information, including contacts, current timber standards and some useful publications.

Turf for tough times - keeping grass cover with less water, Proceedings of a seminar held at Redlands Research Station, Cleveland, Queensland, 6 June 2007.

Suitable for gaining some insights into important questions about the management of turf in dry times. Improve your product quality and avoid unnecessary losses. Can varieties help? How important are soils in conserving moisture and how do I measure my soil's condition? How can I make the best use of available water? Can water retaining amendments assist in establishing turf? Is recycled water a good option? Contains research results from turfgrass trials conducted by Queensland Government scientists for Queensland conditions.

Wood properties and processing outcomes for plantation grown African mahogany (Khaya senegalensis) trees from Clare, Queensland (18 and 20 year-old trees) and Katherine, Northern Territory (14 year-old trees).

Khaya senegalensis, African mahogany, a high-value hardwood, was introduced in the Northern Territory (NT) in the 1950s; included in various trials there and at Weipa, Q in the 1960s-1970s; planted on ex mine sites at Weipa (160 ha) until 1985; revived in farm plantings in Queensland and in trials in the NT in the 1990s; adopted for large-scale, annual planting in the Douglas-Daly region, NT from 2006 and is to have the planted area in the NT extended to at least 20,000 ha. The recent serious interest from plantation growers, including Forest Enterprises Australia Ltd (FEA), has seen the establishment of some large scale commercial plantations. FEA initiated the current study to process relatively young plantation stands from both Northern Territory and Queensland plantations to investigate the sawn wood and veneer recovery and quality from trees ranging from 14 years (NT – 36 trees) to 18-20 years (North Queensland – 31 trees). Field measures of tree size and straightness were complemented with log end splitting assessment and cross-sectional disc sample collection for laboratory wood properties measurements including colour and shrinkage. End-splitting scores assessed on sawn logs were relatively low compared to fast grown plantation eucalypts and did not impact processing negatively. Heartwood proportion in individual trees ranged from 50% up to 92 % of butt cross-sectional disc area for the visually-assessed dark coloured central heartwood and lighter coloured transition wood combined. Dark central heartwood proportion was positively related to tree size (R2 = 0.57). Chemical tests failed to assist in determining heartwood – sapwood boundary. Mean basic density of whole disc samples was 658 kg/m3 and ranged among trees from 603 to 712 kg/m3. When freshly sawn, the heartwood of African mahogany was orange-red to red. Transition wood appeared to be pinkish and the sapwood was a pale yellow colour. Once air dried the heartwood colour generally darkens to pinkish-brown or orange-brown and the effect of prolonged time and sun exposure is to darken and change the heartwood to a red-brown colour. A portable colour measurement spectrophotometer was used to objectively assess colour variation in CIE L*, a* and b* values over time with drying and exposure to sunlight. Capacity to predict standard colour values accurately after varying periods of direct sunlight exposure using results obtained on initial air-dried surfaces decreased with increasing time to sun exposure. The predictions are more accurate for L* values which represent brightness than for variation in the a* values (red spectrum). Selection of superior breeding trees for colour is likely to be based on dried samples exposed to sunlight to reliably highlight wood colour differences. A generally low ratio between tangential and radial shrinkages was found, which was reflected in a low incidence of board distortion (particularly cupping) during drying. A preliminary experiment was carried out to investigate the quality of NIR models to predict shrinkage and density. NIR spectra correlated reasonably well with radial shrinkage and air dried density. When calibration models were applied to their validation sets, radial shrinkage was predicted to an accuracy of 76% with Standard Error of Prediction of 0.21%. There was also a strong predictive power for wood density. These are encouraging results suggesting that NIR spectroscopy has good potential to be used as a non-destructive method to predict shrinkage and wood density using 12mm diameter increment core samples. Average green off saw recovery was 49.5% (range 40 to 69%) for Burdekin Agricultural College (BAC) logs and 41.9% (range 20 to 61%) for Katherine (NT) logs. These figures are about 10% higher than compared to 30-year-old Khaya study by Armstrong et al. (2007) however they are inflated as the green boards were not docked to remove wane prior to being tallied. Of the recovered sawn, dried and dressed volume from the BAC logs, based on the cambial face of boards, 27% could potentially be used for select grade, 40% for medium feature grade and 26% for high feature grades. The heart faces had a slightly higher recovery of select (30%) and medium feature (43%) grade boards with a reduction in the volume of high feature (22%) and reject (6%) grade boards. Distribution of board grades for the NT site aged 14 years followed very similar trends to those of the BAC site boards with an average (between facial and cambial face) 27% could potentially be used for select grade, 42% for medium feature grade, 26% for high feature grade and 5% reject. Relatively to some other subtropical eucalypts, there was a low incidence of borer attack. The major grade limiting defects for both medium and high feature grade boards recovered from the BAC site were knots and wane. The presence of large knots may reflect both management practices and the nature of the genetic material at the site. This stand was not managed for timber production with a very late pruning implemented at about age 12 years. The large amount of wane affected boards is indicative of logs with a large taper and the presence of significant sweep. Wane, knots and skip were the major grade limiting defects for the NT site reflecting considerable amounts of sweep with large taper as might be expected in younger trees. The green veneer recovered from billets of seven Khaya trees rotary peeled on a spindleless lathe produced a recovery of 83% of green billet volume. Dried veneer recovery ranged from 40 to 74 % per billet with an average of 64%. All of the recovered grades were suitable for use in structural ply in accordance to AS/NZ 2269: 2008. The majority of veneer sheets recovered from all billets was C grade (27%) with 20% making D grade and 13% B grade. Total dry sliced veneer recovery from the logs of the two largest logs from each location was estimated to be 41.1%. Very positive results have been recorded in this small scale study. The amount of colour development observed and the very reasonable recoveries of both sawn and veneer products, with a good representation of higher grades in the product distribution, is encouraging. The prospects for significant improvement in these results from well managed and productive stands grown for high quality timber should be high. Additionally, the study has shown the utility of non-destructive evaluation techniques for use in tree improvement programs to improve the quality of future plantations. A few trees combined several of the traits desired of individuals for a first breeding population. Fortunately, the two most promising trees (32, 19) had already been selected for breeding on external traits, and grafts of them are established in the seed orchard.

Innovative technologies to advance Queensland's horticulture processing industries

Enabling processing technologies for the horticultural industries.

Small Log Processing Resource Specification

Sawing studies of mixed species and age plantation hardwoods representing potential early resource flows available to plantation sawlog processing industry. Provide information needed to underpin a business case to invest in small log sawing infrastucture.

Short- and long-term movement patterns in the freshwater whipray (Himantura dalyensis) determined by the signal processing of passive acoustic telemetry data.

Patterns of movement in aquatic animals reflect ecologically important behaviours. Cyclical changes in the abiotic environment influence these movements, but when multiple processes occur simultaneously, identifying which is responsible for the observed movement can be complex. Here we used acoustic telemetry and signal processing to define the abiotic processes responsible for movement patterns in freshwater whiprays (Himantura dalyensis). Acoustic transmitters were implanted into the whiprays and their movements detected over 12 months by an array of passive acoustic receivers, deployed throughout 64 km of the Wenlock River, Qld, Australia. The time of an individual's arrival and departure from each receiver detection field was used to estimate whipray location continuously throughout the study. This created a linear-movement-waveform for each whipray and signal processing revealed periodic components within the waveform. Correlation of movement periodograms with those from abiotic processes categorically illustrated that the diel cycle dominated the pattern of whipray movement during the wet season, whereas tidal and lunar cycles dominated during the dry season. The study methodology represents a valuable tool for objectively defining the relationship between abiotic processes and the movement patterns of free-ranging aquatic animals and is particularly expedient when periods of no detection exist within the animal location data.