Molecular dynamics simulation of sub-transition for polyethersulfone

Molecular dynamics (MD) simulations of a polyethersulfone (PES) chain are carried out in the amorphous state by using the Dreiding 2.21 force field at four temperatures. Two types of molecular motion, i.e, rotations of phenylene rings and torsions of large segments containing two oxygen atoms, two sulfur atoms, and five phenylene rings on the backbone, are simulated. The modeling results show that the successive phenylene rings should be in-phase cooperative rotations, whereas the successive large segments should be out-of-phase cooperative torsions. By calculating the diffusion coefficient for the phenylene ring rotations, it is found that this rotation contributes to the beta -transition of PES.

Interfacial layer and phase inversion behavior in the blend of polyethersulfone and polycarbonate

A blend of polyethersulfone (PES) and polycarbonate (PC) with a ratio of 40/60 was studied by scanning electron microscopy (SEM), dynamic mechanical analysis, and transmission electron microscopy (TEM). It was found that the PES-PC blend is a partially miscible, two-phase system, and an interfacial layer exists between the phases of PES and PC. Specific interaction resulting from the n-complex between PES and PC provides the driving force for formation of the interfacial layer. In addition, phase inversion behavior was also observed for the 40/60 composition.

Mechanical properties and miscibility of polyethersulfone phenoxy blends

The blends of polyethersulfone and phenoxy were prepared by melt mixing in a Brabender-like apparatus. The specimens for measurements were made by compression molding and then were water-quenched at room temperature under pressure. The tensile strength, tensile modulus, elongation at break and yield, density, thermal analysis, and dynamic mechanical properties were each measured. The dependence of tensile strength, tensile modulus, elongation at break and yield, and density on composition was obtained. The relationship between tensile modulus and elongation at break and yield and speed of the crosshead at different weight ratios of the blends is shown. The effects of composition and miscibility on the mechanical properties are discussed. (C) 1996 John Wiley & Sons, Inc.

Effect of physical aging on phenolphthalein polyethersulfone/poly(phenylene sulfide) blend .1. Mechanical properties

The effect of physical aging at 210 degrees C on the mechanical properties of phenolphthalein polyether sulfone (PES-C) and a PES-C/poly(phenylene sulfide) (PPS) blend, with 5% content of PPS, were studied using DMA, tensile experiments, an instrumented impact tester, and SEM observations. The blend shows good mechanical properties in comparison with the corresponding PES-C. The mechanical properties of both materials exhibit characteristics of physical aging, with only the aging rate of the blend relatively slower, which should be attributed to the constraint effect of PPS particles and the good interfacial adhesion. The morphology of the PPS phase in the blend did not change with aging time. The principal role of PPS particles is to induce crazes, which dissipate energy, under applied loading; thus, the blend shows good toughness. On the other hand, the multiple crazing mechanism depends on the molecular mobility or structural state of the matrix. (C) 1996 John Wiley & Sons, Inc.

IN-SITU COMPOSITE - PHENOLPHTHALEIN POLYETHERSULFONE-THERMOTROPIC LIQUID-CRYSTALLINE POLYMER BLENDS

Phase behavior, thermal, theological and mechanical properties plus morphology have been studied for a binary polymer blend. The blend is phenolphthalein polyethersulfone (PES-C) with a thermotropic liquid crystalline polymer (LCP), a condensation copolymer of p-hydroxybenzoic acid with ethylene terephthalate (PHB-PET). It was found that these two polymers form optically isotropic and homogeneous blends by means of a solvent casting method. The homogeneous blends undergo phase separation during heat treatment. However, melt mixed PES-C/PHB-PET blends were heterogeneous based upon DSC and DMA analysis and SEM examination. Addition of LCP in PES-C resulted in a marked reduction of melt viscosity and thus improved processability. Compared to pure PES-C, the charpy impact strength of the blend containing 2.5% LCP increased 2.5 times. Synergistic effects were also observed for the mechanical properties of blends containing < 10% LCP. Particulates, ribbons, and fibrils were found to be the typical morphological units of PHB-PET in the PES-C matrix, which depended upon the concentration of LCP and the processing conditions.

LOCAL MAIN-CHAIN DYNAMICS OF PHENOLPHTHALEIN POLYETHERSULFONE

Local main chain dynamics of dissolved phenolphthalein polyethersulfone (PES-C) in solution with chloroform-d(1) were examined through C-13 NMR relaxation measurements. Spin-lattice relaxation times and NOE (nuclear Overhauser effects) factors were measured as a function of temperature. The relaxation data were interpreted in terms of main chain segmental motion by using the damped orientational diffusion model (DAMP) and the conformation jump model (VJGM) derived by Valeur, Jarry, Geny, and Monnerie. The simulation method used is N-SIMPLEX, which gives, in this study, a result of the object function less than 10(-4). Correlation times were obtained for the main chain motion of PES-C with these models and the results indicate that the main chain of PES-C are flexible. The comparison between PES-C and 1,2-polybutadiene is proposed. The distribution of the correlation time for the main chain motion by using VJGM model is discussed. The temperature dependence of correlation times for PES-C indicating the dynamical rigidity of its chains is obtained.

THERMAL AND MECHANICAL-PROPERTIES OF PHENOLPHTHALEIN POLYETHERSULFONE POLY(PHENYLENE SULFIDE) BLENDS

The thermal and mechanical properties of phenolphthalein polyethersulfone/poly(phenylene sulfide) (PES-C/PPS) blends were studied using a differential scanning calorimeter, a dynamic mechanical analyzer, and mechanical characterization. The morphologies of fracture surfaces were observed by scanning electron microscopy. The blends are multiphase systems with strong interaction between the two phases. It is of interest that, although the strength and ductility of PPS are lower than those of PES-C, the addition of PPS can improve markedly the impact strength of PES-C without changing its higher strength. The PPS can also act as a flow aid for PES-C. (C) 1995 John Wiley and Sons, Inc.

Synthesis of Soluble Poly(arylene ether sulfone) Ionomers with Pendant Quaternary Ammonium Groups for Anion Exchange Membranes

A new bisphenol monomer, 2,2'-dimethylaminemetllylene-4,4'-biphenol (DABP), was easily prepared by Mannich reaction of dimethylamine and formaldehyde with 4,4'-biphenol. Novel partially fluorinated poly(arylene ether sulfone)s with pendant quaternary ammonium groups were prepared by copolymerization of DABP, 4,4'-biphenol, and 3,3',4,4'- tetrafluorodiphenylsulfone, followed by reaction with iodomethane. The resulting copolymers PSQNI-x (where x represents the molar fraction of DABP in the feed) with high molecular weight exhibited outstanding solubility in polar aprotic solvents; thus, the flexible and tough membranes of PSQNI-x with varying ionic content could be prepared by casting from the DMAc solution. Novel anion exchange membranes, PSQNOH-x, were obtained by an anion exchange of PSQNI-x with 1 N NaOH.

Phase-separation behavior of the system PES/phenoxy: An application of the Sanchez-Lacombe lattice fluid theory

Cloud-point curves reported for the system polyethersulfone (PES)/phenoxy were calculated by means of the Sanchez-Lacombe (SL) lattice fluid theory. The one adjustable parameter epsilon(12)*/k (quantifying the interaction energy between mers of the different components) can be evaluated by comparison of the theoretical and experimental phase diagrams. The Flory-Huggins (FH) interaction parameters are computed based on the evaluated epsilon(12)*/k and are approximately a linear function of volume fraction and of inverse temperature. The calculated enthalpies of mixing of PES/phenoxy blends for different compositions are consistent with the experimental values obtained previously by Singh and Walsh [1].

SEQUENCE-ANALYSIS OF FLUORINE-CONTAINING POLYARYLETHERSULFONE COPOLYMERS BY C-13-NMR

HexafluorobisA polyethersulfone-cardo polyethersulfone, random and block copolymers with different segment lengths were synthesized by a reaction of 4,4'-(hexafluoroisopropylidene)diphenol and 3,3'-bis(4-hydroxyphenyl)-1-isobenzopyrrolidone with bis(4-chl

PHASE-BEHAVIOR IN EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER SULFONE)

Phenolphthalein poly(ether ether sulphone) (PES-C) was found to be miscible with uncured bisphenol-A-type epoxy resin, i.e. diglycidyl ether of bisphenol A (DGEBA), as shown by the existence of a single glass transition temperature within the whole composition range. Miscibility between PES-C and DGEBA is considered to be due mainly to the entropy contribution. However, dynamic mechanical analysis (d.m.a.) and scanning electron microscopy (SEM) studies revealed that PES-C exhibits different miscibility with four cured epoxy resins (ER). The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. For the blends cured with amines (4,4'-diaminodiphenylmethane (DDM) and 4,4'-diaminodiphenylsulphone (DDS)), no phase separation occurs as indicated by either d.m.a. or SEM. However, for the blends cured with anhydrides (maleic anhydride (MA) and phthalic anhydride (PA)), both d.m.a. and SEM clearly show evidence of phase separation. SEM study shows that the two phases interact well in the MA-cured blend while the interface between the phases in the PA-cured blend is poorly bonded. The differences in the overall compatibility and the resulting morphology between the amine-cured and anhydride-cured systems have been discussed from the points of view of both thermodynamics and kinetics.

RADIATION-INDUCED CROSS-LINKING OF AROMATIC POLYMERS WITH A CARDO GROUP

The effects of irradiation on some members of the family of aromatic polymers with a cardo group, such as polyetherketone with a cardo group (PEK-C) and polyethersulfone with a cardo group (PES-C), were studied. It was found that PEK-C and PES-C can be crosslinked by irradiation under vacuum. Moreover, it was also found that the intensity of the shake-up peak of x-ray photoelectron spectroscopy (XPS) for PEK-C and PES-C varies with irradiation dose. Gelation doses (Rg) of PEK-C and PES-C were estimated from the XPS shake-up peak.

PHASE-SEPARATION IN ANHYDRIDE-CURED EPOXY-RESIN CONTAINING PHENOLPHTHALEIN POLY(ETHER ETHER KETONE)

Dynamic mechanical analysis and scanning electron microscopy were used to study phase separation of three blends of anhydride-cure bisphenol-A-type epoxy resin with phenolphthalein poly(ether ether ketone). Phase separation was observed for all the blends. The overall compatibility and the resulting morphology of the cured blends are dependent on the choice of cure agent. The phenomena have been discussed from the points of view of both thermodynamics and kinetics. The effects of the choice of hardener on phase separation are considered to be primarily due to differences between the chemical natures of the hardeners.

Investigation into the rheological properties of PES/NMP/nonsolvent membrane-forming systems

From the perspective of a polymer solution, the rheological properties of the popular polyethersulfone (PES)/N-methyl-2-pyrrolidone (NMP)/nonsolvent (NS) membrane-forming system were investigated thoroughly with a controlled stress rheometer (HAAKE RS75, Germany). The scope of the study included measurements of the controlled-stress flow curve, creep recovery, and dynamic oscillation. H2O, 1-butanol, ethylene glycol, and diethylene glycol were used as NS additives. The effects of the polymer concentration and the quality of the solvent mixture, as characterized by the approaching ratio, on the rheological behavior of the dopes were studied. Up to 38 wt % PES and extremely adjacent to the phase separation (i.e., the approaching ratio of the dope was 0.95), the viscous property dominated all the dopes, which behaved as Newtonian fluids. Moreover, all the membrane-forming dopes investigated were in the crossover regime in the semidilute region, in which the chains were overlapping but unentangled. (C) 2001 John Wiley & Sons, Inc.