Wireless optical communication-based spatial pattern

We propose a novel communication technique which utilizes a set of mutually distinguishable optical patterns instead of convergent facula to transmit information. The communication capacity is increased by exploiting the optical spatial bandwidth resources. An optimum detector for this communication is proposed based on maximum-likelihood decision. The fundamental rule of designing signal spatial pattern is formulated from analysis of the probability of error decision. Finally, we present a typical electro-optical system scheme of the proposed communication. (c) 2006 Elsevier GmbH. All rights reserved.

Far-field spot compression without energy loss in main lob in wireless laser communication

Far-field spot compression without energy loss in main lob is of great significance to wireless laser communication. In this letter, we propose two schemes to obtain far-field spot compression without energy loss in main lob. One scheme is based on the simulated annealing (SA) algorithm. Using SA algorithm, we design the phase profile of the diffractive phase element (DPE). Using the designed DPE, far-field spot compression without energy loss in main lob is achieved. The other scheme is based on YG algorithm. By means of YG algorithm, we appropriately designed the DPE in the emitting plane. Using the DPE, far-field spot compression without energy loss in main lob is obtained. (c) 2007 Elsevier GmbH. All rights reserved.

A Complex BPF with On Chip Auto-tuning Architecture for Wireless Receivers

A 3(rd) order complex band-pass filter (BPF) with auto-tuning architecture is proposed in this paper. It is implemented in 0.18um standard CMOS technology. The complex filter is centered at 4.092MHz with bandwidth of 2.4MHz. The in-band 3(rd) order harmonic input intercept point (IIP3) is larger than 16.2dBm, with 50 Omega as the source impedance. The input referred noise is about 80uV(rms). The RC tuning is based on Binary Search Algorithm (BSA) with tuning accuracy of 3%. The chip area of the tuning system is 0.28 x 0.22 mm(2), less than 1/8 of that of the main-filter which is 0.92 x 0.59 mm(2). After tuning is completed, the tuning system will be turned off automatically to save power and to avoid interference. The complex filter consumes 2.6mA with a 1.8V power supply.

Low Power Integrated Circuits for Wireless Neural Recording Applications

A group of prototype integrated circuits are presented for a wireless neural recording micro-system. An inductive link was built for transcutaneous wireless power transfer and data transmission. Power and data were transmitted by a pair of coils on a same carrier frequency. The integrated receiver circuitry was composed of a full-wave bridge rectifier, a voltage regulator, a date recovery circuit, a clock recovery circuit and a power detector. The amplifiers were designed with a limited bandwidth for neural signals acquisition. An integrated FM transmitter was used to transmit the extracted neural signals to external equipments. 16.5 mW power and 50 bps - 2.5 Kbps command data can be received over 1 MHz carrier within 10 mm. The total gain of 60 dB was obtained by the preamplifier and a main amplifier at 0.95Hz - 13.41 KHz with 0.215 mW power dissipation. The power consumption of the 100 MHz ASK transmitter is 0.374 mW. All the integrated circuits operated under a 3.3 V power supply except the voltage regulator.

Implantable Microsystem for Wireless Neural Recording Applications

A prototype microsystem is presented for wireless neural recording application. An inductive link was built for transcutaneous wireless power transfer and data transmission. Total 16.5 mW power and 50 bps - 2.5 Kbps command data can be received over 1 - 5 MHz with a distance of 0-10 mm. The integrated amplifiers were designed with a limited bandwidth for neural signals acquisition. The gain of 60 dB was obtained by preamplifier at 7 Hz - 3 KHz. An integrated FM transmitter was used to transmit the extracted neural signals to external equipments with 0.374 - 2 mW power comsumption and a maximum data rate of 500 Kbps at 100 MHz. All the integrated circuits modules except the power recovery circuit were tested or stimulated under a 3.3 V power supply, and fabricated in standard CMOS processing.

一种基于QoS的服务构件组合方法

在面向服务的架构中,如何利用已有的服务构件组装成新的服务成为当前此领域的一个研究热点.该文以构件化嵌入式操作系统Liquid为背景,给出了一种基于QoS的服务构件组合方法,在满足组合服务的功能需求同时,满足其QoS需求.文章详细给出了所涉及的服务模型、QoS模型以及构件选择基本算法.为使此服务构件组合方法适应于动态变化的系统环境,该文进一步对构件选择基本算法进行优化,给出了构件选择的启发和协商算法.最后通过实验,比较和分析三种算法的性能.

基于QoS的Pareto最优的服务选择

随着越来越多的服务能够满足用户的功能需求,需要一种策略基于服务的多种QoS属性来帮助用户选择合适的服务。以XML描述服务的QoS属性,提出了一种基于QoS的Pareto最优的服务选择策略,选择出那些不在所有的QoS属性上劣于其它服务的服务。实验结果表明,与随机选择和偏好导向的选择策略相比,Pareto最优策略有独特的效果。

QuCOM:一种面向构件系统的QoS管理模型

在性能变化不确定的系统内,不同的应用处于竞争和共享有限的系统资源、并受其变化影响的环境中·在系统运行时,对于需要QoS保证的应用,为保证其QoS属性,应能适应于这种环境·考虑到系统资源的全局管理特性,仅从应用中增加适应机制是不够的,还需在系统层中增加QoS管理机制·为此,给出了一种面向构件系统的QoS管理模型———QuCOM(qualitycomponent)及其集成到系统构件框架的方法,使基于QuCOM开发的构件应用能够适应于变化的系统环境,并为了验证QuCOM的有效性,以一个视频流应用为例,给出了相关实验数据分析·

OnceAS/Q:一个面向QoS的Web应用服务器

网络分布计算环境下应用系统的需求多样化和复杂性的增长,要求位于中间件层次的Web应用服务器(web application server,简称WAS)从原来的尽力而为服务模型转变为服务质量(quality of service,简称QoS)保障模型,为具有不同需求的应用分别提供适宜的服务质量保障.目前的WAS系统在此方面仍然比较薄弱.OnceAS/Q是一个面向QoS的WAS系统,它以QoS规约为基础,为不同应用提供不同的QoS保障能力.OnceAS/Q实现了一个应用QoS保障框架,提供了一组QoS服务组件支持具有QoS需求的应用开发和运行.介绍了OnceAS/Q的体系结构和主要组件,详细阐述了两个关键问题,一是QoS规约的定义及其映射,另一个是面向QoS的服务组件和资源的动态重配.OnceAS/Q原型在Ecperf测试基准下,对其QoS保障能力进行了实验.实验数据表明,在较大规模的应用环境下,OnceAS/Q能够提供更好的服务质量,并且开销是可接受的.