A multi-standard active-RC filter with accurate tuning system

A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architec-ture is presented. It exhibits 1EEE 802. 11a/b/g (9.5 MHz) and DVB-H (3 MHz, 4 MHz) application. The filter exploits digitally-controlled polysilicon resistor banks and a phase lock loop type automatic tuning system. The novel and complex automatic frequency calibration scheme provides better than 4 comer frequency accuracy, and it can be powered down after calibration to save power and avoid digital signal interference. The filter achieves OIP3 of 26 dBm and the measured group delay variation of the receiver filter is 50 ns (WLAN mode). Its dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from a 2.85 V supply. The dissipation of calibration consumes 2 mA. The circuit has been fabricated in a 0.35μm 47 GHz SiGe BiCMOS technology; the receiver and transmitter filter occupy 0.21 mm~2 and 0.11 mm~2 (calibration circuit excluded), respectively.

用VHDL实现的23位快速浮点数加减法器

With the development of LSI, FPGA/CPLD has been used more and more in the fields of digital signal processing and au-tocontrol and so on. And with the development of the techniques of digital processing, for fitting the system’s function, it should be a higher requirement to speed and used-resource to compute the floating point numbers. The author introduces a high speed adder-subtracter of the 23 bit’s floating point numbers, which is carried out with the parallel arithmetic and the computational speed cou...中文文摘：随着大规模集成电路的不断发展,FPGA/CPLD在数字信号处理、自动控制等方面得到了越来越多的应用。并且伴随着数字化处理技术的不断发展,为满足系统功能的要求,对浮点数运算的速度以及相应占用的资源也就提出了更高的要求。笔者即介绍了以VHDL语言为基础,采用并行算法且计算速度达到33MHz的,对23位标准浮点数实现的高速浮点加减法运算器,并以Cyclone II芯片EP2C20F484为硬件环境,最终进行时序模拟仿真,从而验证该浮点加减法器的正确性和快速特性。

电机转速自适应测量方法及其在DSP上的实现

本文在分析几种常用的基于编码器测速方法的基础上,提出了一种高性能的自适应速度测量方法。该方法选择一个可变的时间周期和编码器脉冲数来测量单位时间内的编码器脉冲数,再通过简单的计算得到转速的测量值。数字信号处理器(DSP)芯片集成有正交脉冲编码电路,并且数据处理速度快,实时性强。本文中提出的方法在电机控制专用DSP芯片TMS320 LF2407A上进行了实现。实验研究表明,可以在提高低速时的测速准确度的同时,提高系统的响应时间。该方法已经在自主研发的全数字伺服驱动系统中得到了成功应用。

基于MAX5307和DSP的多回路测控系统设计

提出了一种多回路测控系统的设计方案。该方案仅使用一个DSP(数字信号处理器)及一个多通道集成的D/A转换器件MAX5307,不仅同时保证了多个测控回路的实时性及控制精度,而且实现简单,成本低廉。文中结合实际系统,给出了其具体的硬件和软件实现。该方法具有广泛的适用性,对类似系统的设计具有参考价值。

基于DSP旋翼飞行机器人增稳操纵杆设计

本文首先介绍了旋翼飞行机器人控制系统的功能与应用,着重介绍了其中基于tmx320f28335数字信号处理器的无线增稳操控系统工作原理、硬件构架以及软件流程,并对AD转换过程中的关键FIR滤波算法进行说明,详尽比较了不同滤波参数对滤波效果的影响,最后得到该方法可以应用于旋翼飞行机器人增稳控制系统的结论,并将应用该方法滤波后的控制信号应用于实际增稳飞行,以实际数飞行据验证上述结论。

微型ROV控制装置及控制方法

介绍了一种基于嵌入式ARM9技术的微型ROV的控制装置及控制方法。该装置可以同时进行两通道串行通讯,实现微型ROV的视频信号、潜水深度、艏向角度、纵倾角度、横摇角度、电子舱温度等数据的采集和与上位机的通讯传输;该装置可以采集16路模拟量信号和12路数字量信号,输出4路模拟量信号和12路TTL电平信号,实现推进器、水下灯、水下摄像机、云台等ROV功能器件的驱动。该装置具有通讯能力强、集成度高、功耗低等特点,可以满足微型ROV所有的常用功能要求。

Crosstalk analysis of a fiber laser sensor array system based on digital phase-generated carrier scheme

A detailed study on analyzing the crosstalk in a wavelength division multiplexed fiber laser sensor array system based on a digital phase generated carrier interferometric interrogation scheme is reported. The crosstalk effects induced by the limited optical channel isolation of a dense wavelength division demultiplexer (DWDM) are presented, and the necessary channel isolation to keep the crosstalk negligible to the output signal was calculated via Bessel function expansion and demonstrated by a two serial fiber laser sensors system. Finally, a three-element fiber laser sensor array system with a 50-dB channel-isolation DWDM was built up. Experimental results demonstrated that there was no measurable crosstalk between the output channels.

Improved digital processing method used for image motion measurement based on hybrid opto-digital joint transform correlator

Hybrid opto-digital joint transform correlator (HODJTC) is effective for image motion measurement, but it is different from the traditional joint transform correlator because it only has one optical transform and the joint power spectrum is directly input into a digital processing unit to compute the image shift. The local cross-correlation image can be directly obtained by adopting a local Fourier transform operator. After the pixel-level location of cross-correlation peak is initially obtained, the up-sampling technique is introduced to relocate the peak in even higher accuracy. With signal-to-noise ratio >= 20 dB, up-sampling factor k >= 10 and the maximum image shift <= 60 pixels, the root-mean-square error of motion measurement accuracy can be controlled below 0.05 pixels.