Orientation preference and fractal character of short fatigue cracks in a weld metal

Short fatigue crack behaviour in a weld metal has been further investigated. The Schmid factor and the fractal dimension of short cracks on iso-stress specimens subjected to reversed bending have been determined and then applied to account for the distribution and orientation characteristics of short fatigue cracks. The result indicates that the orientation preference of short cracks is attributed to the large values of Schmid factor at relevant grains. The Schmid factors of most slip systems, which produced short cracks, are less than or equal to 0.4. Crack length measurements reveal that short crack path, compared to that of long crack, possesses a more stable and relatively larger value of fractal dimension. This is regarded as one of the typical features of short cracks.

Initiation and propagation of short fatigue cracks in a weld metal

Fatigue tests were performed using a purpose designed triangular shaped specimen to investigate the initiation and propagation of short fatigue cracks in a weld metal. It was observed that short fatigue cracks evolved from slip bands and were predominantly within ferrite grains. As the test progressed, the short crack density increased with minor changes in crack length. The growth of short cracks, in the early stage resulted mainly from coalescence with other existing cracks. The mechanism of short crack behaviour is discussed.

High efficiency operation of butt joint line-defect-waveguide microlaser in two-dimensional photonic crystal slab

Butt joint line-defect-waveguide microlasers are demonstrated on photonic crystal slabs with airholes in a triangular lattice. Such microlaser is designed to increase the output power from the waveguide edge directly. The output power is remarkably enhanced to 214 times higher by introducing chirped structure in the output waveguide. The lasing mode operates in the linear dispersion region of the output waveguide so that the absorption loss due to the band-edge effect is reduced. The laser resonance is illustrated theoretically using the finite difference time domain method. A practical high power efficiency of 20% is obtained in this microlaser. (C) 2008 American Institute of Physics.

A novel butt-joint scheme for the preparation of electro-absorptive lasers

A 1.55 mu m InGaAsP/InGaAsP multiple-quantum-well electro-absorption modulator (EAM) monolithically integrated with a distributed feedback laser (DFB) diode has been realized based on a novel butt-joint scheme by ultra-low metal-organic vapour phase epitaxy for the first time. The threshold current of 25 mA and an extinction ratio of more than 30 dB are obtained by using the novel structure. The beam divergence angles at the horizontal and vertical directions are as small as 19.3 degrees x 13 degrees, respectively, without a spot-size converter by undercutting the InGaAsP active region. The capacitance of the ridge waveguide device with a deep mesa buried by polyimide was reduced down to 0.30 pF.

Butt-coupled MOVPE growth for high-performance electro-absorption modulator integrated with a DFB laser

A novel butt-joint coupling scheme is proposed to improve the coupling efficiency for the integration of a GalnAsP MQW distributed feedback (DFB) laser with an MQW electro-absorption modulator (EAM). The proposed method gives more than 90% coupling efficiency, being much higher than the 26% coupling efficiency of the common MQW-MQW coupling technique. The differential quantum efficiency of the MQW-bulk-MQW coupled device is also much higher than that of the MQW-MQW device, 0.106 mW/mA versus 0.02 mW/mA. The EAM-DFB devices fabricated by the proposed method exhibit a very high modulation efficiency (12 dB/V) from 0 to I V. By adopting a high-mesa ridge waveguide and buried polyimide, the capacitance of the modulator is reduced to about 0.28 pF. The experimental results demonstrate that the method can replace the conventional MQW-MQW coupling technique to fabricate high-quality integrated photonic devices. (C) 2007 Elsevier B.V. All rights reserved.

Butt-Joint Monolithicaily Integrated DFB-LD/EA-MD Light Source for 10Gbit/s Transmission

This paper reports on the design, fabrication, and performance of an integrated electro-absorptive modulated laser based on butt-joint configuration for 10Gbit/s application. This paper mainly aims at two aspects. One is to improve the optical coupling between the laser and modulator; another is to increase the bandwidth of such devices by reducing the capacitance parameter of the modulator. The integrated devices exhibit high static and dynamic characteristics. Typical threshold current is 15mA,with some value as low as 8mA. Output power at 100mA is more than 10mW. The extinction characteristics,modulation bandwidth, and electrical return loss are measured. 3dB bandwidth more than 10GHz is monitored.

Theoretical Study on the Butt-coupling of Semiconductor Laser and Fiber Bragg Grating

The butt-coupling between a semiconductor laser diode and a fiber Bragg grating external cavity acts a key roll on the laser characteristics. The scatter matrix method considering the butt-coupling efficiency is used to analyze the butt-coupling between them. It is found that the butt-coupling distance and coupling efficiency determine the laser characteristics. For strong feedback, the single lasing wavelength changes in the reflection bandwidth of the effective reflectivity ( approximately the Bragg region of the fiber Bragg grating) as the distances change. For weak feedback condition, some different results are obtained. The SMSRs in the two conditions are presented and analyzed. These results can provide important design guidance of device parameters for the practical fabrication.

Integrated electroabsorption-modulated DFB laser by using an improved butt-joint method

An improved butt coupling method is used to fabricate an electroabsorption modulator (EAM) monolithically integrated with a distributed feedback (DFB) laser. The obtained electroabsorption-modulated laser (EML) chip with the traditional shallow ridge exhibits very low threshold current of 12 mA, output power of more than 8 mW, and static extinction ratio of -7 dB at the applied bias voltage from 0.5 to -2.0 V.

K418与42CrMo异种金属的激光穿透焊接

实验研究了连续波Nd：YAG激光焊接速度、侧吹保护气流量和离焦量等参量对激光穿透焊接K418和42CrMo焊缝成形的影响。结果表明，K418与42CrMo激光穿透焊接有X形和T形两种典型的焊缝形貌，且焊缝形貌是不对称的。随着焊接速度的提高，焊接线能量降低，焊缝尺寸变小，且焊缝上部尺寸变化比下部尺寸变化慢，焊缝形貌由X形过渡到T形。当离焦量在瑞利长度范围内时，焊缝正面宽度变化很小；当离焦量超出瑞利长度范围时，在足够高的激光功率密度下，焊缝正面宽度快速增加。在激光功率为3kW，侧吹保护气角度为35°条件下，通过优化焊接速度、侧吹保护气流量和离焦量等参量可以得到最佳焊缝质量。

Collective evolution characteristics and computer simulation of short fatigue cracks

Fatigue testing was conducted using a kind of triangular isostress specimen to obtain the short-fatigue-crack behaviour of a weld low-carbon steel. The experimental results show that short cracks continuously initiate at slip bands within ferrite grain domains and the crack number per unit area gradually increases with increasing number of fatigue cycles. The dispersed short cracks possess an orientation preference, which is associated with the crystalline orientation of the relevant slip system. Based on the observed collective characteristics, computer modelling was carried out to simulate the evolution process of initiation, propagation and coalescence of short cracks. The simulation provides progressive displays which imitate the appearance of experimental observations. The results of simulation indicate that the crack path possesses a stable value of fractal dimension whereas the critical value of percolation covers a wide datum band, suggesting that the collective evolution process of short cracks is sensitive to the pattern of crack site distribution.

平台用高强度钢多次补焊及TIG熔修的疲劳分析

海洋石油平台在服役期内，由于受到各种环境载荷的交变作用，其受力的焊接构件不可避免地会出现疲劳裂纹。对出现的疲劳裂纹进行补焊修复，可以延长平台的使用期，带来巨大的经济和社会效益。本文通过实验研究，考察了多次补焊对海洋平台用高强度钢焊接接头疲劳性能的影响，以及是否可以通过TIG熔修工艺的采用提高补焊构件的疲劳寿命，达到延长补焊后平台的使用寿命，减少补焊次数的目的。本文涉及的主要研究内容如下：1、考察了多次补焊对焊接接头疲劳寿命的影响。通过对平台用高强度钢焊接接头初焊试样，以及重复三次补焊试样的疲劳实验，得到了各次补焊试样在对数正态分布和威布尔分布下的寿命估算式和考虑了存活率的R-S-N曲线。对实验结果进行了比较和分析，从而考察了多次补焊对焊接接头疲劳性能的影响。2、在每次补焊后，由于焊趾外移造成了焊趾角的变化，使得焊趾处的应力集中系数发生了变化。本文采用有限元方法计算了试样的应力场分布，得到了焊趾处的应力集中系数与焊趾角的关系。考虑到应力集中系数的变化后，对多次补焊试样疲劳实验的实验数据进行了重新处理。3、考察了多次补焊熔修对焊接接头疲劳寿命的影响。本文通过对平台用高强度钢焊接接头补焊及补焊熔修试样的疲劳实验，得到了多次补焊和补焊熔修试样对数正态分布和威布尔分布下的寿命估算式和考虑了存活率的R-S-N曲线。对实验结果进行了比较和分析，从而考察了补焊后采用TIG熔修工艺对焊接接头疲劳性能的影响。4、一次补焊后进行熔修处理可以极大的改善试样的疲劳性能，提高试样的疲劳寿命。但这一结果是在平焊位条件下得出了。为了将这一结果用于实际，还要考察实际操作中大量采用的立焊位条件下熔修的效果。本文完成了立焊位条件下补焊及补焊熔修试样的疲劳实验，得到了相应的S-N曲线。5、疲劳实验数据的处理中，大量采用威布尔分布作为数据统计的分布类型。但由于威布尔分布具有三个参数，给求解带来一定的困难。本文提出一种以在威布尔坐标纸上，数据分布的线形相关系数作为判据的求解威布尔参数的方法，并通过程序加以实现。为了对疲劳实验数据的处理更加方便和直观，编制了“疲劳实验数据处理程序“，将对疲劳实验数据的编辑、分布参数的求解、不同存活率下的疲劳寿命估算和各种分布类型图以及R-S-N曲线的绘制工作包括在该程序中。

High performance of 1.55 mu m DFB integrated with vertically tapered self-aligned spot-size converter

A new type of self-aligned spotsize converter (SSC) integrated 1.55 mum DFB lasers had been proposed in this article. The upper optical confinement layer and the butt-coupled tapered thickness waveguide were regrown simultaneously, which not only offered the separate optimization of the active region and the integrated SSC, but also reduced the difficulty of the butt-joint selective regrowth. The vertical and horizontal far field angles were 9degrees and 12degrees respectively, the 1- dB misalignment tolerance were both 3.6 and 3.4 mum. The directed coupling efficiency to tapered single mode fiber was 48%.

Selective-area MOCVD growth for distributed feedback lasers integrated with vertically tapered self-aligned waveguide

The growth pressure and mask width dependent thickness enhancement factors of selective-area MOCVD. grow th were investigated in this article. A, high enhancement of 5.8 was obtained at 130 mbar with the mask width of 70 mum. Mismatched InGaAsP (-0.5%) at the maskless region which could ensure the material at butt-joint region to be matched to InP was successively grown by controlling the composition and mismatch modulation in the selective-area growth. The upper optical confinement layer and the butt-coupled tapered thickness waveguide were regrown simultaneously in separated confined heterostructure 1.55 gm distributed feedback laser, which not only offered the separated optimization of the active region and the integrated spotsize converter, but also reduced the difficulty of the butt-joint selective regrowth. A narrow beam of 9degrees and 12degrees in the vertical and horizontal directions, a low threshold current of 6.5 mA was fabricated by using this technique. (C) 2003 Elsevier Science B.V. All rights reserved.

Design and performance of monolithic integrated electro-absorption modulated distributed feedback laser - art. no. 67820Y

High performance InGaAsP/InGaAsP strained compensated multiple-quantum-well (MQW) electroabsorption modulators (EAM) monolithically integrated with a DFB laser diode have been designed and realized by ultra low metal-organic vapor phase epitaxy (MOVPE) based on a novel butt joint scheme. The optimization thickness of upper SCH layer for DFB and EAM was obtained of the proposed MQW structure of the EAM through numerical simulation and experiment. The device containing 250(mu m) DFB and 170(mu m) EAM shows good material quality and exhibits a threshold current of 17mA, an extinction ratio of higher than 30 dB and a very high modulation efficiency (12dB/V) from 0V to 1V. By adopting a high-mesa ridge waveguide and buried polyimide, the capacitance of the modulator is reduced to about 0.30 pF corresponding to a 3dB bandwidth more than 20GHz.