SiO_2薄膜折射率的准确拟合分析

精确的光学常数对于设计和制备高品质的光学薄膜非常重要,尤其是那些光学性能对折射率变化敏感的薄膜。SiO_2是一种常用的低折射率材料,因与常用基底折射率相近使其准确拟合有一定难度。实验通过离子束溅射制备了SiO_2单层膜。考虑测量时的误差和基底折射率的影响,采用透射率包络和反射率包络得到了SiO_2的折射率,并用所得折射率进行反演来对这两种途径在实际测量拟合过程中的准确性进行比对。分析表明,剩余反射率在实际的测量过程中误差更小,直接用测量镀膜前后基片的剩余反射率值可以更简便更准确地得到SiO_2的折射率,能达到10~(-2)的精度。

非粮原料燃料乙醇发酵关键技术的研究

生物质燃料乙醇是一种高度清洁的交通液体燃料，是减少温室气体排放，缓解大气污染的最佳技术选择。以非粮原料生产燃料乙醇可以在进行能源生产的同时保证粮食安全，有利于产业的可持续发展。在众多的非粮原料中，甘薯是我国开发潜力最大的生物质能源作物之一。我国占世界甘薯种植总面积和产量的90％。同时，甘薯的单位面积燃料乙醇产量远大于玉米和小麦。其成本是目前酒精中最低廉的，因此利用甘薯生产乙醇是发展生物质燃料乙醇的首要选择。目前采用薯类全原料主要采用分批发酵生产乙醇，其技术水平低，发酵强度低，一般在0.7－2.5g/（L•h），乙醇浓度低，甘薯发酵乙醇为6－8％(v/v)，能耗高，环境负荷大，污染严重。针对上述问题，本文从菌株选育、原料预处理、中试放大、残糖成分分析等方面进行研究。 为了研究乙醇发酵生产规模扩大过程中，大型发酵罐底部高压条件下，CO2对酵母乙醇发酵的影响，我们通过CO2 加压的方法进行模拟试验，研究结果表明，发酵时间随压强的升高而逐渐延长，高压CO2 对乙醇发酵效率影响不大，在0.3 MPa 以下时，发酵效率均可达到90%以上。高压CO2 对发酵的抑制作用是高压和CO2 这两个因素联合作用的结果。高压CO2 条件下，酵母胞外酶和胞内重要酶类的酶活均表现出特征性。0.2 MPa 下，酶活性的变化趋势和0.1 MPa 条件下的较为一致。而0.3 MPa 下的酶活变化趋势与0.4 MPa 下的酶活更为接近。通过全基因表达分析发现在CO2 压力为0.3 MPa 下，乙醇发酵途径中多个基因表达量下调，同时海藻糖合成酶和热激蛋白基因表达量上调。 筛选耐高温的乙醇酵母菌株能够解决糖化温度和发酵温度不协调的矛盾，实现真正意义上的边糖化边发酵。高温发酵还能够降低发酵时的冷却成本，实现乙醇的周年生产。本研究筛选出一株高温发酵菌株Y-H1，进而我们对该菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性进行了分析。结果表明Y-H1 能够在40 ℃条件下正常进行乙醇发酵，发酵33h，最终乙醇浓度达到10.7%（w/w），发酵效率达到90%以上。同时发酵液最终pH 在3.5 左右，显示菌株具有一定的耐酸性能力。同时观察到40 ℃下，菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性发生了变化，乙醇发酵途径中关键酶基因表达下调，而海藻糖合成酶与热激蛋白基因表达量上调，这些结果为进一步研究酵母菌耐热调控机理提供了依据。 糖蜜是一种大规模工业生产乙醇的理想原料，本研究利用选育高浓度乙醇发酵菌株结合配套的发酵稳定剂，研究了糖蜜高浓度乙醇发酵情况。结果表明采用冷酸沉淀预处理糖蜜溶液，采用分批补料的发酵方式，乙醇浓度最高达到了10.26% (w/w)，发酵时间为42 h。同时观察到在糖蜜发酵中，乙醛含量与乙醇浓度存在一定的相关性。 快速乙醇发酵对于缩短乙醇生产周期、降低乙醇生产成本、减少原料腐烂损失具有重要意义。本研究诱变和筛选得到了一株快速乙醇发酵菌株10232B。在优化后的发酵条件下，采用10L 发酵罐进行分批乙醇发酵，经过18h,乙醇的最终浓度达到88.5g/L,发酵效率93.6%，平均乙醇生产速度达到4.92 g/L/h。此菌株在保持较高乙醇生产浓度的同时，拥有快速生产乙醇的能力，适合作为快速乙醇发酵生产菌种。 由于鲜甘薯具有粘度大的特点，传统液化糖化处理很难在短时间内充分糖化原料；高粘度的醪液也难以进行管道输送，容易堵塞管路；同时，也会降低后续的乙醇发酵效率。 本文采用了快速粘度分析法对鲜甘薯糊化粘度特性进行了分析，进而对预处理条件进行了研究，在最佳预处理条件下，糖化2h 后，醪液葡萄糖值最高可达99.3，粘度4.5×104 mPa.s，而采用传统糖化工艺，醪液DE 值仅为85.8，粘度大于1.0×105 mPa.s。 此预处理方法也可用于快速糖化不加水的醪液。后续的乙醇发酵试验表明，通过此预处理方法获得的糖化醪液对乙醇发酵无负面影响。 在前期已实现了实验室水平的鲜甘薯燃料乙醇快速乙醇发酵基础上，进一步将发酵规模扩大到500L，在中试水平上对甘薯乙醇发酵进行了研究。结果表明在500L 中试规模，采用边糖化边发酵（SSF）工艺，在料液比为3∶1，发酵醪液最高粘度为6×104mPa.s 条件下，发酵37h，乙醇浓度达到了12.7%（v/v），发酵效率91%，发酵强度为2.7 g/（L•h）。与目前国内的薯类乙醇发酵生产技术水平具有明显的优越性。 为研究甘薯、木薯乙醇发酵中残糖的组成，采用了高效液相色谱—蒸发光散射检测法，对乙醇发酵残糖进行了分析。结果表明，甘薯、木薯乙醇发酵残糖均为寡聚糖，主要由葡萄糖、木糖、半乳糖、阿拉伯糖和甘露糖构成。随着发酵时间延长，寡聚糖中的葡萄糖、半乳糖、甘露糖可被缓慢的水解释放。提高糖化酶量仅在一定程度上降低残糖，过量的糖化酶反而会导致残糖增加。同时发现3, 5-二硝基水杨酸法不能准确测定甘薯、木薯乙醇发酵中的残总糖含量。进一步筛选了两株残糖降解菌株，对甘薯乙醇发酵残糖的降解利用率均达到了40%以上，而且还能显著降低发酵醪液粘度。经形态学和rRNA ITS 序列分析，确定这两株菌分别属于为木霉属和曲霉属黑曲霉组。 通过对以甘薯原料为代表的非粮原料发酵技术研究开发，以期形成乙醇转化率高，能耗低，生产效率高、季节适应性好，原料适应性广，经济性强，符合清洁生产机制的燃料乙醇高效转化技术，为具有我国特色的燃料乙醇发展模式提供技术支持。 Sweet potato is one of the major feedstock for the fuel ethanol production in China. The planting area and the yield in China take 90% of the world. Sweet potato is an efficient kind of energy crops. The energy outcome per area is higher than corn or wheat. And the manufacture cost of ethanol is the lowest, compared with corn and wheat. So sweet potato is the favorable crop for the bioethanol production in China. However, the low-level fermentation technology restricts the development of ethanol production by sweet potato, including slow ethanol production rate, low ethanol concentration and high energy cost. To solve these problems, we conducted research on the strain breeding, pretreatment, pilot fermentation test and residual saccharides analysis. To study the impact of hyperbaric condition at bottom of the large fermentor on yeast fermentation, high pressure carbon dioxide (CO2) was adopted to simulate the situation. The results showed that the fermentation was prolonged with the increasing pressure. The pressure of CO2 had little impact on the ethanol yield which could reach 90% under the pressure below 0.3 MPa. The inhibition was combined by the high pressure and CO2. Under the high CO2 pressure, the extracellular and important intracellular enzyme activities were different from those under normal state. The changes under 0.1 MPa and 0.2 MPa were similar. The changes under 0.3 MPa were closer to those under 0.4 MPa. The application of thermotolerance yeast could solve the problem of the inconsistent temperature between fermentation and saccharificaton and fulfill the real simultaneous saccharification and fermentation. And it could reduce the cooling cost. A thermotolerance strain Y-H1 was isolated in our research. It gave high ethanol concentration of 10.7%（w/w）at 40 ℃ for 33 h. The ethanol yield efficiency was over 90%. At 40 ℃, the extracellular and important intracellular enzyme activities of Y-H1 showed the difference with normal state, which may indicate its physiological changes at the high temperature. Molasses is another feedstock for industrial ethanol production. By our ethanol-tolerance strain and the regulation reagents, the fermentation with high ethanol concentration was investigated. In fed-batch mode combined with cold acid deposition, the highest ethanol concentration was 10.26% (w/w) for 42h. The aldehyde concentration in fermentation was found to be related to ethanol concentration. The development of a rapid ethanol fermentation strain of Zymomonas mobilis is essential for reducing the cost of ethanol production and for the timely utilization of fresh material that is easily decayed in the Chinese bioethanol industry. A mutant Z. mobilis strain, 10232B, was generated by UV mutagenesis. Under these optimized conditions, fermentation of the mutant Z. mobilis 10232B strain was completed in just 18 h with a high ethanol production rate, at an average of 4.92 gL-1h-1 per batch. The final maximum ethanol concentration was 88.5 gL-1, with an ethanol yield efficiency of 93.6%. This result illustrated the potential use of the mutant Z. mobilis 10232B strain in rapid ethanol fermentation in order to help reduce the cost of industrial ethanol production. As fresh sweet potato syrup shows high viscosity, it is hard to be fully converted to glucose by enzymes in the traditional saccharification process. The high-viscosity syrup is difficult to be transmitted in pipes, which may be easily blocked. Meanwhile it could also reduce the later ethanol fermentation efficiency. To solve these problems, effects of the pretreatment conditions were investigated. The highest dextrose equivalent value of 99.3 and the lowest viscosity of 4.5×104 mPa.s were obtained by the most favorable pretreatment conditions, while those of 85.8 and over 1.0×105 mPa.s was produced by traditional treatment conditions. The pretreatment could also be applied on the material syrup without adding water. The later experiments showed that the pretreated syrup had no negative effect on the ethanol fermentation and exhibited lower viscosity. The fuel ethanol rapid production from fresh sweet potato was enlarged in the 500L pilot scale after its fulfillment on the laboratory level. The optimal ratio of material to water was 3 to 1 in 500L fermentor. With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg for 37h, which reached 92% of theoretical yield. The average ethanol production rate was 4.06 g/kg/h. And the maximum viscosity of syrup reached 6×104mPa.s. The results showed its superiority over current industrial ethanol fermentation. The compositions of the residual saccharides in the ethanol fermentation by sweet potato and cassava were analyzed by high performance liquid chromatography coupled with evaporative light-scattering detector. The results showed that all the residual saccharides were oligosaccharides, mainly composed of glucose, xylose, galactose, arabinose and mannose. The glucose, galactose and mannose could be slowly hydrolyzed from oligosaccharides in syrup during a long period. To increase the glucoamylase dosage could lower the residual saccharides to a certain extent. However, excess glucoamylase dosage led to more residual saccharides. And the method of 3, 5-dinitrosalicylic acid could not accurately quantify the residual total saccharides content. Two residual saccharides degrading strains were isolated, which could utilize 40% of total residual saccharide and lower the syrup viscosity. With the analysis of morphology and internal transcribed spacer sequence, they were finally identified as species of Trichoderma and Aspergillus niger.

Structural Failure Analysis and Numerical Simulation of Micro-Accelerometers under Impulsive Loading

Micromachined accelerometer is a kind of inertial MEMS devices, which usually operate under intensive impact loading. The reliability of micromachined accelerometers is one of the most important performance indices for their design, manufacture and commer

On nonequilibrium of pyrolysis process in the manufacture of ethene

Nonequilibrium process for cracking ethane and n-buthane in the manufacture of ethene has been analytically and numerically investigated in a Heavi-side function temperature field and through a normal shock wave. The results demonstrate that, while the reaction temperature increases, the maximum value of ethene yield is increased, and the optimal reaction duration is sharply shortened. For the identical initial reaction temperature, the maximum value of ethene yield through a stationary normal shock wave is less than that in a Heavi-side function temperature field. However, the ethene consumption after the maximum value in the former case is less than that in the latter. Higher ethene yield will be obtained by using the gasdynamic heating method than by using the current methods.

PMMA with Long-Persistent Phosphors and Its Behavior of Luminescence

A new kind of rare earth material with high efficient long-persistent phosphors, such as SrAl2O4: Eu, Dy, has been developed in recent years. The PMMA with long-persistent phosphors is typical one of applications for the phosphors. In this work, we try to probe into the affection of the manufacture process on the PMMA with long-persistent phosphors, to analyze its performance, and its luminescence behavior, especially to study the self-excitation of the PMMA with long-persistent phosphors.

Research Progress On Thermal Protection Materials And Structures Of Hypersonic Vehicles

Hypersonic vehicles represent future trends of military equipments and play an important role in future war. Thermal protection materials and structures, which relate to the safety of hypersonic vehicles, are one of the most key techniques in design and manufacture of hypersonic vehicles. Among these materials and structures, such as metallic temperature protection structure, the temperature ceramics and carbon/carbon composites are usually adopted in design. The recent progresses of research and application of ultra-high temperature materials in preparation, oxidation resistance, mechanical and physical characterization are summarized.

Processing Simulation of Virtual Manufacture in Laser Surface Treatmenthang

Processing simulation is at the bottom of the coral technology of VM and is also difficult due to the complexity of mechanism and diversity of parameters. Previously much research has been mainly carried out on the geometrical simulation or physical simulation respectively. The aim of this paper is to study the processing simulation in laser surface treatment based on the mechanism, put forward the architecture of the whole processing simulation and give the models of the processing. As a result the data structure layers in the whole simulation is presented.

Development And Application Of Flexible Substrate Sensors In Instantaneous Heat Flux Measurement

A new type of sensor with the flexible substrate is introduced. It is applicable in measuring instantaneous heat flux on the model surface in a hypersonic shock tunnel. The working principle, structure and manufacture process of the sensor are presented. The substrate thickness and the dynamic response parameter of the sensor are calculated. Because this sensor was successfully used in measuring the instantaneous heat flux on the surface of a flat plate in a detonation-driven shock tunnel, it may be effective in measuring instantaneous heat flux on the model surface.

Effect of elliptical manufacture error of an axicon on the diffraction-free beam patterns

Based on the generalized Huygens-Fresnel diffraction integral theory and the stationary-phase method, we analyze the influence on diffraction-free beam patterns of an elliptical manufacture error in an axicon. The numerical simulation is compared with the beam patterns photographed by using a CCD camera. Theoretical simulation and experimental results indicate that the intensity of the central spot decreases with increasing elliptical manufacture defect and propagation distance. Meanwhile, the bright rings around the central spot are gradually split into four or more symmetrical bright spots. The experimental results fit the theoretical simulation very well. (C) 2008 Society of Photo-Optical Instrumentation Engineers.

The research and progress of micro-fabrication technologies of two-dimensional photonic crystal

The novel material of photonic crystal makes it possible to control a photon, and the photonic integration will have breakthrough progress due to the application of photonic crystal. It is based on the photonic crystal device that the photonic crystal integration could be realized. Therefore, we should first investigate photonic crystal devices based on the active and the passive semiconductor materials, which may have great potential application in photonic integration. The most practical and important method to fabricate two-dimensional photonic crystal is the micro-manufacture method. In this paper, we summarize and evaluate the fabrication methods of two-dimensional photonic crystal in near-infrared region, including electron beam lithography, selection of mask, dry etching, and some works of ours. This will be beneficial to the study of the photonic crystal in China.

Abatement of waste gases and water during the processes of semiconductor fabrication

The purpose of this article is to examine the methods and equipment for abating waste gases and water produced during the manufacture of semiconductor materials and devices. Three separating methods and equipment are used to control three different groups of electronic wastes. The first group includes arsine and phosphine emitted during the processes of semiconductor materials manufacture. The abatement procedure for this group of pollutants consists of adding iodates, cupric and manganese salts to a multiple shower tower (MST) structure. The second group includes pollutants containing arsenic, phosphorus, HF, HCl, NO2, and SO3 emitted during the manufacture of semiconductor materials and devices. The abatement procedure involves mixing oxidants and bases in an oval column with a separator in the middle. The third group consists of the ions of As, P and heavy metals contained in the waste water. The abatement procedure includes adding CaCO3 and ferric salts in a flocculation-sedimentation compact device equipment. Test results showed that all waste gases and water after the abatement procedures presented in this article passed the discharge standards set by the State Environmental Protection Administration of China.

Urban functional structure characteristics and transformation in China

The paper analyzes urban functional structure characteristics of Chinese cities in 1996 using the Nelson method. The manufacturing employment percentage is much higher in metropolitan areas but is decreasing from 1989 to 1996. On the other hand, the weight of science, education, culture, hygiene, finance, insurance and real estate increases. The employment structure changes dramatically. Although the urbanization level of China is lower than that of the USA in 1955, the frequency distribution curve of urban functions is similar. The construction, transportation, commerce, finance, insurance, real estate, science, education, culture, hygiene and administration curves are normal. The mining employment converges on minor cities and the distribution is not normal. The urban function has changed with urban scale. The bigger the cities are, the smaller the manufacture, mining and construction employment weights, and the larger are the science, education, finance, insurance, real estate and administration weights. Commerce and transportation are distributed evenly and the difference is less. From the comparison in three zones of China, the employment percentage of manufacture, finance, insurance and real estate is higher in eastern coastal areas, while the employment percentage of science, education, administration is higher in western areas. (C) 2002 Elsevier Science Ltd. All rights reserved.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .3. Determination of the time of pressure application

The curing temperature, pressure, and curing time have significant influence on finished thermosetting composite products. The time of pressure application is one of the most important processing parameters in the manufacture of a thermosetting composite. The determination of the time of pressure application relies on analysis of the viscosity variation of the polymer, associated with curing temperature and curing time. To determine it, the influence of the time of pressure application on the physical properties of epoxy-terminated poly(phenylene ether ketone) (E-PEK)-based continuous carbon fiber composite was studied. It was found that a stepwise temperature cure cycle is more suitable for manufacture of this composite. There are two viscosity valleys, in the case of the E-PEK system, associated with temperature during a stepwise cure cycle. The analysis on the effects of reinforcement fraction and defect content on the composite sheet quality indicates that the width-adjustable second viscosity valley provides a suitable pressing window. The viscosity, ranging from 400 to 1200 Pa . s at the second viscosity valley, is the optimal viscosity range for applying pressure to ensure appropriate resin flow during curing process, which enables one to get a finished composite with optimal fiber volume fraction and low void content. (C) 1997 John Wiley & Sons, Inc.