Comparison of photobioreactors and optimal light regime for rapid vegetative propagation of transgenic Undaria pinnatifida gametophytes

BACKGROUND: Previously, tachyplesin gene (tac) has been successfully transferred into Undaria pinnatifida gametophytes using the method of microprojectile bombardment transformation. The objectives of this study were to compare and evaluate the performance of bubble-column and airlift bioreactors to determine a preferred configuration of bioreactor for vegetative propagation of transgenic U. pinnatifida gametophytes, and to then investigate the influence of light on vegetative propagation of these gametophytes, including incident light intensity, photoperiod and light quality to resolve the problems of rapid vegetative propagation within the selected bioreactor. RESULTS: Experimental results showed that final dry cell density in the airlift bioreactor was 12.7% higher than that in the bubble-column bioreactor under the optimal aeration rate of 1.2 L air min(-1) L-1 culture. And a maximum final dry cell density of 2830 mg L-1 was obtained within the airlift bioreactor using blue light at 40 mu mol m(-2) s(-1) with a light/dark cycle of 14/10 (h). Polymerase chain reaction (PCR) analysis indicated that genes (bar and tac) were not lost during rapid vegetative propagation within the airlift bioreactor. CONCLUSION: The airlift bioreactor was shown to be much more suitable for rapid vegetative propagation of transgenic U. pinnatifida gametophytes than the bubble-column bioreactor in the laboratory. The use of blue light allows improvement of vegetative propagation of transgenic U. pinnatifida gametophytes. (C) 2009 Society of Chemical Industry

Effects of Irradiance and Temperature on the Photosynthesis and Vegetative Propagation of Caulerpa serrulata

The photosynthetic oxygen evolution of Caulerpa serrulata was determined with oxygen electrodes. The effects of light and temperature on the growth and regeneration of fragmented C. serrulata thalli were analyzed. The regenerating rate and establishment of different sizes and portions of C. serrulata were studied. The results showed that the light saturation point of C. serrulata was 200 mu mol photons/m(2) per s and the optimum growth temperature was 25-30 degrees C. Under these conditions, the maximum photosynthetic oxygen evolution rate was 15.1 +/- 0.29 mg O-2/mg Chl a/h, the growth rate and elongation rate reached the highest values, 4.67 +/- 0.09 mg FW/d and 0.78 +/- 0.01 mm/d, respectively. The fragmented C. serrulata thalli was regenerated at 20-35 degrees C and survived at 15 degrees C and 200 mu mol photons/m(2) per s. A different survival rate was detected according to fragment size. All of these results indicated that C. serrulata was a candidate to become an invasive species if introduced into a new place. Therefore, we should pay more attention to C. serrulata for its potential threat to marine ecosystem when it is sold for aquarium use.

德国鸢尾快速分株繁殖的研究

本实验用喷施6-BA和茎切生根的方法建立了一套德国鸢尾快速分株繁殖的体系。用3 000 mg/L 或5 000 mg/L 的6-BA 对德国鸢尾（Iris germanica）‘lovely again’进行单次喷施可以促进根茎芽的萌发和根状茎的形成。在喷施后的30 天到90 天内，BA的促进作用在具有2个或4个起始根状茎的植株上表现得很显著，但对于只有一个起始根状茎的植株不显著。在喷施后的150 天以及第二年，具有2个或4个起始根状茎的母株总体上比只具有1个起始根状茎的母株产生了更多的根状茎。而6-BA的喷施对母株的叶面积和叶片数变化没有显著影响。在早春时，把处于不同发育阶段的侧芽或小根茎从母株上取下，并且用不同浓度的IBA处理。总体上，处于较高发育阶段的茎切（芽切）在生根率、初级根和次级根的数目，总根长、根干重以及植株高度等测量指标方面的表现较好。IBA对德国鸢尾的茎切（芽切）的生根作用不显著。多次喷施6-BA 对德国鸢尾根茎芽的生出的促进作用显著，并且使生物量重新分配。连续喷施6-BA后，对内源生长素和细胞分裂素的连续测定结果表明，6-BA的作用主要是解除了顶端优势对侧芽的萌发和生长的抑制，从而形成新的根茎。

Transient expression of lacZ in particle bombarded Gracilaria changii (Gracilariales, Rhodophyta)

Using a Biolistic PDS 1000/He system, healthy thalli of Gracilaria changii were bombarded with gold particles coated with plasmid DNA containing the lacZ reporter gene. Transient expression of lacZ was observed in bombarded thalli under the rupture-disc pressures of 4482, 6206, 7584 and 8963 KPa, two days after bombardment. Although G. changii exhibits a slight blue background, positive expression and the background colour can be clearly differentiated. The results indicate that lacZ could be a useful reporter gene and that SV40 promoter could be an effective promoter for Gracilaria transformation.

转基因海带配子体的制备与高效增殖

海带具有很高的营养价值和经济社会价值。自20世纪90年代以来，本实验室在借鉴高等植物基因工程原理和方法的基础上，根据海带自身特点，建立了海带遗传转化体系（海带孢子体表达系统），它的基本原理是利用基因枪法转化海带配子体，经孤雌或受精途径再生幼孢子体后，用氯霉素筛选幼孢子体获得转基因海带，然后进行海上安全栽培和转基因产品的检测与提取。目前该表达系统已成功实现报告基因（β-半乳糖苷酶基因，lacZ）和功能基因（乙肝表面抗原基因，HBsAg）的稳定表达。 由于海带孢子体表达系统需经孢子体再生和海上栽培等阶段，周期较长，而且转基因安全性问题也在一定程度上制约其研究与应用。因此，我们在海带孢子体表达系统的基础上又建立和优化了海带配子体表达系统，并成功实现了报告基因（绿色荧光蛋白基因，GFP）的瞬间表达和功能基因（瑞替普酶基因，rt-PA）的稳定表达。虽然海带配子体表达系统能避免转基因安全性问题，周期较短，但在表达量和生物量积累方面，与孢子体表达系统相比还有较大差距。 本文首先在海带配子体表达系统中成功实现了人酸性成纤维细胞生长因子基因（hafgf）和鲎素基因（tac）的稳定表达，制备了转基因海带配子体，然后将光生物反应器培养技术应用于转基因海带配子体的高效增殖，以期解决阻碍海带配子体表达系统发展的量的问题，并为转基因海带配子体的大规模培养提供试验依据和技术支持。 本文的研究结果为： 1、人酸性成纤维细胞生长因子基因和鲎素基因可以稳定整合到海带配子体基因组中，实现转基因产物的表达。 2、根据转基因海带配子体的生长特点，研制开发了一套培养体积为300 ml的鼓泡式光生物反应器，它具有操作简便、成本低廉、适合海带配子体生长等特点。随后将培养体系扩大到2.5 L，并研究了光对转基因海带配子体生长的影响，试验结果显示，转基因海带配子体在光强为30 μE m-2 s-1时即可达到光饱和生长，最优光周期为14:10 LD，而且蓝光可促进转基因海带配子体的生长。 3、在前期研究工作的基础上，为改善反应器内的传质条件，我们又设计研制了2.5 L气升式光生物反应器用于转基因海带配子体的高效增殖。研究发现，气升式光生物反应器较鼓泡式光生物反应器能明显地改善反应器内的传质状态，实现转基因海带配子体更高密度的培养（生物量可达到1,990 mg L-1），是一套高密度悬浮培养转基因海带配子体的有效装置和设备。

Tank cultivation of the red alga Palmaria palmata: Year-round induction of tetrasporangia, tetraspore release in darkness and mass cultivation of vegetative thalli

Field-collected tetrasporophytes of Palmaria palmata were tumbled in 300-L outdoor tanks from January to August at ambient daylength or in a constant short-day (SD) regime (8 h light per day), both at 10 or 15 degrees C. Tetrasporangia were massively induced after 2.5 months under SD conditions at 10 degrees C and completely lacking at 15 degrees C, both under SD or ambient daylength conditions, with a few tetrasporangia present at 10 degrees C and ambient daylength. Elongation rates of tagged tetrasporophytic thalli peaked from March to April in all four conditions, when the biomass densities in the outdoor tanks were close to 2.5 kg fresh weight m(-2). Under all four conditions, juvenile proliferations started to appear in June from the margins of the old fronds, and attained approximately 1 cm in length by the end of July. Approximately 80% of the tetraspores were released during the first three dark phases in a light/dark regime, and the remaining 20% during the light phases. A minimum of 10 min darkness was observed to trigger spore release. White light inhibited tetraspore release, while a similar number of spores were released in continuous red light or in the light/dark regime, although with no significant differences of spore release during subjective days and nights. Sporelings were successfully derived from the released tetraspores for mass propagation of the male gametophyte in 2000-L outdoor tanks in a greenhouse. Mass production of male gametophytic sporelings of P. palmata was completed two times by SD induction of tetrasporangia at 10 degrees C, release of spores in darkness and culturing the sporelings until they were ready to be propagated vegetatively in greenhouse tanks. One experiment lasted from January to October 2001, with spore release in June, and the second from September to April 2003, with spore release in January. These results may support the development of sustainable, year-round Palmaria farming. (c) 2005 Elsevier B.V. All rights reserved.

Wave Propagation Analysis in a Pressure-Wave-Refrigerator

Pressure wave refrigerators (PWR) refrigerate the gas through periodical expansion waves. Due to its simple structure and robustness, PWR may have many potential applications if the efficiency becomes competitive with existing alternative devices. In order to improve the efficiency, the characteristics of wave propagation in a PWR are studied by experiment, numerical simulation and theoretical analysis. Based on the experimental results and numerical simulation, a simplified model is suggested, which includes the assumptions of flux-equilibrium and conservation of the free energy. This allows the independent analysis of the operation parameters and design specifics. Furthermore, the optimum operation condition can be deduced. Some considerations to improve the PWR efficiency are also given.

Flame Propagation of H_2-Air in a Semi-Open Obstructed Tube

针对氢／空气混合物,通过实验研究了其预混火焰在半开口管道中的火焰传播加速现象,结果表明,火焰传播状态随着氢气当量比的变化而发生改变。当氢／空气混合物被点燃后,由于障碍物的扰动,火焰在管道中不断加速传播,并最终到达一准稳态传播。在氢气当量比0.31附近时,火焰速度发生跃变。当氢气当量比足够大时,火焰传播由爆燃态转变为爆轰态。在本实验条件下,爆燃转准爆轰的临界条件是d/Lambda>=2.6（d是圆环形障碍物内径,人是爆轰格胞尺度）。障碍物阻塞比的变化对最大火焰速度和压力提升的影响不明显。

Numerical simulation of an adaptive optics system with laser propagation in the atmosphere

A comprehensive model of laser propagation in the atmosphere with a complete adaptive optics (AO) system for phase compensation is presented, and a corresponding computer program is compiled. A direct wave-front gradient control method is used to reconstruct the wave-front phase. With the long-exposure Strehl ratio as the evaluation parameter, a numerical simulation of an AO system in a stationary state with the atmospheric propagation of a laser beam was conducted. It was found that for certain conditions the phase screen that describes turbulence in the atmosphere might not be isotropic. Numerical experiments show that the computational results in imaging of lenses by means of the fast Fourier transform (FFT) method agree well with those computed by means of an integration method. However, the computer time required for the FFT method is 1 order of magnitude less than that of the integration method. Phase tailoring of the calculated phase is presented as a means to solve the problem that variance of the calculated residual phase does not correspond to the correction effectiveness of an AO system. It is found for the first time to our knowledge that for a constant delay time of an AO system, when the lateral wind speed exceeds a threshold, the compensation effectiveness of an AO system is better than that of complete phase conjugation. This finding indicates that the better compensation capability of an AO system does not mean better correction effectiveness. (C) 2000 Optical Society of America.

Microcracks Propagation in One Al/SiCp under Impact Loading

Numerous microcracks propagation in one metal matrix composite, Al/SiCp under impact loading was investigated. The test data was got with a specially designed impact experimental approach. The analysis to the density, nucleating locations and distributions of the microcracks as well as microstructure effects of the original composite was received particular emphasis. The types of microcracks or debonding nucleated in the tested composite were dependent on the stress level and its duration. Distributions of the microcracks were depended on that of microstructures of the tested composite while total number of microcracks in unit area and unit duration, was controlled by the stress levels. Also, why the velocity was much lower than theoretical estimations for elastic solids and why the microcracks propagating velocities increased with the stress levels' increasing in current experiments were analysed and explained.

Effect of Microtopography, Slope Length and Gradient, and Vegetative Cover on Overland Flow Through Simulation

Overland flow on a hillslope is significantly influenced by its microtopography, slope length and gradient, and vegetative cover. A 1D kinematic wave model in conjunction with a revised form of the Green-Ampt infiltration equation was employed to evaluate the effect of these surface conditions. The effect of these conditions was treated through the resistance parameter in the kinematic wave model. The resistance in this paper was considered to be made up of grain resistance, form resistance, and wave resistance. It was found that irregular slopes with microtopography eroded more easily than did regular slopes. The effect of the slope gradient on flow velocity and flow shear stress could be negative or positive. With increasing slope gradient, the flow velocity and shear stress first increased to a peak value, then decreased again, suggesting that there exists a critical slope gradient for flow velocity and shear stress. The vegetative cover was found to protect soil from erosion primarily by enhancing erosion-resisting capacity rather than by decreasing the eroding capability of overland flow.

Stress Wave Propagation in a Gradient Elastic Medium

The gradient elastic constitutive equation incorporating the second gradient of the strains is used to determine the monochromatic elastic plane wave propagation in a gradient infinite medium and thin rod. The equation of motion, together with the internal material length, has been derived. Various dispersion relations have been determined. We present explicit expressions for the relationship between various wave speeds, wavenumber and internal material length.

Three-Dimensional Propagation of the Transmitted Shock Wave in a Square Cross-Sectional Chamber

An investigation into the three-dimensional propagation of the transmitted shock wave in a square cross-section chamber was described in this paper, and the work was carried out numerically by solving the Euler equations with a dispersion-controlled scheme. Computational images were constructed from the density distribution of the transmitted shock wave discharging from the open end of the square shock tube and compared directly with holographic interferograms available for CFD validation. Two cases of the transmitted shock wave propagating at different Mach numbers in the same geometry were simulated. A special shock reflection system near the corner of the square cross-section chamber was observed, consisting of four shock waves: the transmitted shock wave, two reflection shock waves and a Mach stem. A contact surface may appear in the four-shock system when the transmitted shock wave becomes stronger. Both the secondary shock wave and the primary vortex loop are three-dimensional in the present case due to the non-uniform flow expansion behind the transmitted shock.

Distinct Element Analysis on Propagation Characteristics of P-Wave in Rock Pillar with Finite length

以节理岩体等效刚度的概念为基础,讨论了离散元刚性块体模型中节理刚度的选取问题。采用面-面接触模型模拟了纵波在一维岩体中的传播,给出了纵波波形；研究了阻尼比、软弱夹层以及节理间是否可拉对波传播规律的影响。