Size Effect and Geometrical Effect of Polycrystals and Thin Film/Substrate System in Micro-indentation Test

Micro-indentation test at scales on the order of sub-micron has shown that the measured hardness increases strongly with decreasing indent depth or indent size, which is frequently referred to as the size effect. Simultaneously, at micron or sub-micron scale, the material microstructure size also has an important influence on the measured hardness. This kind of effect, such as the crystal grain size effect, thin film thickness effect, etc., is called the geometrical effect by here. In the present research, in order to investigate the size effect and the geometrical effect, the micro-indentation experiments are carried out respectively for single crystal copper and aluminum, for polycrystal aluminum, as well as for a thin film/substrate system, Ti/Si3N4. The size effect and geometrical effect are displayed experimentally. Moreover, using strain gradient plasticity theory, the size effect and the geometrical effect are simulated. Through comparing experimental results with simulation results, length-scale parameter appearing in the strain gradient theory for different cases is predicted. Furthermore, the size effect and the geometrical effect are interpreted using the geometrically necessary dislocation concept and the discrete dislocation theory. Member Price: $0; Non-Member Price: $25.00

Experimental study and simulation principles of an oil-gas multiphase transportation system

Presented is an experimental study on the performance of an oil-gas multiphase transportation system, especially on the multiphase flow patterns, multiphase pumping and multiphase metering of the system. A dynamic simulation analysis is conducted to deduce simulation parameters of the system and similarity criteria under simplified conditions are obtained. The reliability and feasibility of two-phase flow experiment with oil and natural gas simulated by water and air are discussed by using the similarity criteria.

Dislocation evolution in epitaxial multilayers and graded composition buffers

This paper presents models to describe the dislocation dynamics of strain relaxation in an epitaxial uniform layer, epitaxial multilayers and graded composition buffers. A set of new evolution equations for nucleation rate and annihilation rate of threading dislocations is developed. The dislocation interactions are incorporated into the kinetics process by introducing a resistance term, which depends only on plastic strain. Both threading dislocation nucleation and threading dislocation annihilation are characterized. The new evolution equations combined with other evolution equations for the plastic strain rate, the mean velocity and the dislocation density rate of the threading dislocations are tested on GexSi1-x/Si(100) heterostructures, including epitaxial multilayers and graded composition buffers. It is shown that the evolution equations successfully predict a wide range of experimental results of strain relaxation and threading dislocation evolution in the materials system. Meanwhile, the simulation results clearly signify that the threading dislocation annihilation plays a vital role in the reduction of threading dislocation density.

Preliminary Investigation of Fluid Flow in Meso-Scale Rectangular Tube

The fluid flow associated with micro and meso scale devices is currently of interest. Experiments were performed to study the fluid flow in meso-scale channels. A straight flow tube was fabricated with 1.0x4.0mm^2 in rectangular cross section and 200mm in length, which was made of quartz for flow visualization and PIV measurements. Reynolds numbers were ranged from 311 to over 3105. The corresponding pressure drop was from 0.65KPa to over 16.58KPa between the inlet and outlet of the tube. The micro PIV was developed to measure the velocity distribution in the tube. A set of microscope object lens was mounted ahead of CCD camera to obtain optimized optical magnification on the CCD chip. The velocity distributions near the outlet of the tube were measured to obtain full-developed flow. A CW laser beam was focused directly on the test section by a cylinder lens to form a small light sheet. Thus, high power density of light was formed on the view region. It is very important to the experiment while the velocity of the flow reaches to a few meters per second within millimeter scale. In this case, it is necessary to reduce exposure time to microseconds for PIV measurements. In the present paper, the experimental results are compared with the classical theories.

Prediction of particle distribution in isotropic turbulence by large-eddy simulation

The recent application of large-eddy simulation (LES) to particle-laden turbulence requires that the LES with a subgrid scale (SGS) model could accurately predict particle distributions. Usually, a SGS particle model is used to recover the small-scale structures of velocity fields. In this study, we propose a rescaling technique to recover the effects of small-scale motions on the preferential concentration of inertial particles. The technique is used to simulate particle distribution in isotropic turbulence by LES and produce consistent results with direct numerical simulation (DNS). Key words: particle distribution, particle-laden turbulence, large-eddy simulation, subgrid scale model.

Atomistic Simulation On Size-Dependent Yield Strength And Defects Evolution Of Metal Nanowires

A simple derivation based on continuum mechanics is given, which shows the surface stress is critical for yield strength at ultra-small scales. Molecular dynamics (MD) simulations with modified embedded atom method (MEAM) are employed to investigate the mechanical behaviors of single-crystalline metal nanowires under tensile loading. The calculated yield strengths increasing with the decrease of the cross-sectional area of the nanowires are in accordance with the theoretical prediction. Reorientation induced by stacking faults is observed at the nanowire edge. In addition. the mechanism of yielding is discussed in details based on the snapshots of defects evolution. The nanowires in different crystallographic orientations behave differently in stretching deformation. This study on the plastic properties of metal nanowires will be helpful to further understanding of the mechanical properties of nanomaterials. (C) 2009 Elsevier B.V. All rights reserved.

Root zone microbial populations, urease activities, and purification efficiency for a constructed wetland

In order to investigate the effects of microorganisms and their urease activities in macrophytic root zones on pollutant removal, four small-scale plots (SSPs) of vertical/reverse-vertical flow wetlands were set up to determine: a) the relationship between the abundance of microorganisms in the root zones and water purification efficiency; and b) the relationship between urease activities in the root zones and pollutant removal in a constructed wetland system. Total numbers of the microbial population (bacteria, fungi, and actinomyces) along with urease activities in the macrophytic root zones were determined. In addition, the relationships between microbial populations and urease activities as well as the wastewater purification efficiencies of total phosphorus (TP), total Kjeldahl nitrogen (TKN), biochemical oxygen demand in 5 days (BOD5), and chemical oxygen demand (COD) were also analyzed. The results showed that there was a highly significant positive correlation (r = 0.9772, P < 0.01) between the number of bacteria in the root zones and BOD5 removal efficiency and a significant negative correlation (r = -0.9092, P < 0.05) between the number of fungi and the removal efficiency of TKN. Meanwhile, there was a significant positive correlation (r = 0.8830, P < 0.05) between urease activities in the root zones and the removal efficiency of TKN. Thus, during wastewater treatment in a constructed wetland system, microorganism and urease activities in the root zones were very important factors.

面向微粒操纵的介电泳芯片系统研究

针对目前在纳米器件及传感器的制造中尚无对大量粒子进行有效操纵的方法,我们利用介电泳方法对大量微粒进行定位和传输操纵,介绍了利用MEMS工艺进行介电泳芯片加工的过程以及整个观测与实验系统的建立,通过有限元软件对传统介电泳和行波介电泳中电极阵列的电场分布进行求解,并在该实验系统下实现了对微通道中的悬浮高度和微粒的运动速度的测量.该实验系统的研究为液体环境下微纳颗粒的装配和分离提供了一条有效的技术路径.

城市发展与地质环境相互作用机制及数量分析—北海市可持续发展战略研究

Based on a viewpoint of an intricate system demanding high, this thesis advances a new concept that urban sustainable development stratagem is a high harmony and amalgamation among urban economy, geo-environment and tech-capital, and the optimum field of which lies in their mutual matching part, which quantitatively demarcates the optimum value field of urban sustainable development and establishes the academic foundation to describe and analyze sustainable development stratagem. And establishes a series of cause-effect model, a analysissitus model, flux model as well as its recognizing mode for urban system are established by the approach of System Dynamics, which can distinguish urban states by its polarity of entropy flows. At the same time, the matter flow, energy flow and information flow which exist in the course of urban development are analyzed based on the input/output (I/O) relationships of urban economy. And a new type of I/O relationships, namely new resources-environment account, are established, in which both resource and environment factors are considered. All above that settles a theoretic foundation for resource economy and environment economy as well as quantitative relationships of inter-function between urban development and geoenvironment, and gives a new approach to analyze natinal economy and urban sustainable development. Based on an analysis of the connection between resource-environmental construct of geoenvironment and urban economy development, the Geoenvironmental Carrying Capability (GeCC) is analyzed. Further more, a series of definitions and formula about the Gross Carrying Capability (GCC), Structure Carrying Capability (SCC) and Impulse Carrying Capability (ICC) is achieved, which can be applied to evaluate both the quality and capacity of geoenvironment and thereunder to determine the scale and velocity for urban development. A demonstrative study of the above is applied to Beihai city (Guangxi province, PRC), and the numerical value laws between the urban development and its geoenvironment is studied by the I/O relationship in the urban economy as following: · the relationships between the urban economic development and land use as well as consumption of underground water, metal mineral, mineral energy source, metalloid mineral and other geologic resources. · the relationships between urban economy and waste output such as industrial "3 waste", dust, rubbish and living polluted water as well as the restricting impact of both resource-environmental factors and tech-capital on the urban grow. · Optimization and control analysis on the reciprocity between urban economy and its geoenvironment are discussed, and sensitive factors and its order of the urban geoenvironmental resources, wastes and economic sections are fixed, which can be applied to determine the urban industrial structure, scale, grow rate matching with its geoenvironment and tech-capital. · a sustainable development stratagem for the city is suggested.

Influence of Surface Stress on Frequency of Microcantilever-Based Biosensors (vol 10, pg 307, 2004)

Microcantilever-based biosensors have been found increasing applications in physical, chemical, and biological fields in recent years. When biosensors are used in those fields, surface stress and mass variations due to bio-molecular binding can cause the microcantilever deform or the shift of frequency. These simple biosensors allow biologists to study surface biochemistry on a micro or nano scale and offer new opportunities in developing microscopic biomedical analysis with unique characteristics. To compare and illustrate the influence of the surface stress on the frequency and avoid unnecessary and complicated numerical solution of the resonance frequency, some dimensionless numbers are derived in this paper by making governing equations dimensionless. Meanwhile, in order to analyze the influence of the general surface stress on the frequency, a new model is put forward, and the frequency of the microcantilever is calculated by using the subspace iteration method and the Rayleigh method. The sensitivity of microcantilever is also discussed. (19 refs.)

水泥回转窑热工控制模型研究及其仿真

水泥回转窑是建材工业发展的方向，我国是水泥生产大国，而国内回转窑与发达国家相差甚大，尤其在热工控制方面。由于水泥回转窑具有时变、分布参数和非线性特性，是一个典型的复杂过程，因而水泥回转窑控制系统是一个很有意义且困难的研究方向，本论文在借鉴国内外同类研究的基础上，提出了模糊专家系统控制模型，进行了深入地研究，并且对该模型进行了计算机仿真，希望通过这项研究，提高我国在水泥回转窑先进智能技术的控制水平。主要研究内容有：对水泥回转窑的热工过程进行了详细分析，对其不同控制方法进行全面的综述，对水泥回转窑实现控制的人工智能方法进行了全面的综述，并介绍了国内外的研究现状；研究了对水泥回转窑控制的模糊控制模型、专家系统设计方法，以及利用模糊控制与专家系统相结合的方法对水泥回转窑进行安全而有效控制的方法：研究了专家系统的实时性问题，提出了静态排列专家系统的推理时间模型、优化排列专家系统的时间估计模型与排列准则；利用计算机仿真方法，实现对水泥回转窑这种复杂而昂贵系统控制进行实验研究，以较低的代价实现对其分析。本论文的主研究成果如下：1. 详细研究了水泥回转窑的技术发展与结构演化过程，分析了水泥回转窑的热工过程以及影响水泥生产的各种因素，总结了影响水泥生产质量的主要因素与次要因素，确定了控制水泥回转窑的主要并且可测量的过程参数。2. 用推理全成方法研究模糊控制模型，实现从模糊的角度研究水泥回转窑的控制：从专家 系统角度研究水泥回转窑的控制问题，并提取了有关的专家系统控制规则；在模糊控制与专家系统的基础上，将水泥回转窑的模糊控制与专家系统相结合，利用层次化的控制器结构，底层为模糊控制器，顶层为专家系统，实现了水泥回转窑的安全与有效控制。3. 从定量的角度研究了专家系统的推理时间问题，给出了三种相应的时间估计模型，这不仅可以分析水泥回转窑系统中的专家系统的实时性，而且也可以分析一般专家系统的推理时间和问题。4. 本文提出的计算机仿真工具，为三组数据分别进行计算机仿真，以此研究水泥回转窑控制策略的性能以及对其动态过程进行分析，为水泥回转窑这样的复杂且昂贵的控制系统研究提供有效的手段。

Impact of laser-accelerated micron-size projectile on dense plasma

The impact of a laser-accelerated micron-size projectile on a dense plasma target is studied using two-dimensional particle-in-cell simulations. The projectile is first accelerated by an ultraintense laser. It then impinges on the dense plasma target and merges with the latter. Part of the kinetic energy of the laser-accelerated ions in the projectile is deposited in the fused target, and an extremely high concentration of plasma ions with a mean kinetic energy needed for fusion reaction is induced. The interaction is thus useful for laser-driven impact fusion and as a compact neutron source.

Characterization of novel microsatellite loci in rare minnow (Gobiocypris rarus) and amplification in closely related species in Gobioninae

Rare minnow (Gobiocypris rarus) is an endangered small fish endemic to upper reach of the Yangtze River. From a (GT)n enriched genomic library, 32 microsatellites were isolated and characterized. Nineteen of these loci were polymorphic in a test population with alleles ranging from 2-7, and observed and expected heterozygosities from zero to 0.8438, and 0.2679 to 0.8264, respectively. In the cross-species amplifications, 13 out of 19 polymorphic loci were found to be also polymorphic in at least one of the 7 closely related species of the subfamily Gobioninae. These polymorphic microsatellite loci should provide sufficient level of genetic diversity to evaluate the fine-scale population structure in rare minnow and its closely related species for the conservation purpose.

Isolation and characterization of polymorphic microsatellites in a sex-reversal fish, rice field eel (Monopterus albus)

The rice field eel (Monopterus albus) is a fish of economic importance in China and some Asian countries. From a (GT)(n)-enriched genomic library, 30 microsatellites were developed by employing the fast isolation by AFLP of sequences containing repeats (FIASCO) protocol. Thirteen loci exhibited polymorphism with two to 13 alleles (mean 7.9 alleles/locus) in a test population and observed heterozygosity ranged from 0.3125 to 0.9688 (mean 0.7140). These loci should provide sufficient level of genetic variation to study the fine-scale population structure and reproductive ecology of the species.