三峡永久船闸高边坡开挖三维离散元数值模拟:3-D Simulation of the Excavation of High Steep Slope of Three-Gorges Permanent Lock by Distinct Element Method

采用面一面接触的三维离散元刚性块体模型,从实测节理面中取出其中的三组,按照其倾向、倾角和节理间距将三峡永久船闸未开挖的区域划分为10~5个离散单元,通过施加力边界条件,给出了与实测初始地应力场接近的数值模拟结果；然后,分4步模拟了永久船闸的开挖过程。计算结果表明：开挖过程会引起节理面出现张开趋势,个别岩体还会沿着节理面滑移。岩体位移的不对称现象较为自然地说明了由节理引起的岩体各向异性特征。

Analysis of critical excavation depth for a jointed rock slope using a face-to-face discrete element method

The critical excavation depth of a jointed rock slope is an important problem in rock engineering. This paper studies the critical excavation depth for two idealized jointed rock slopes by employing a face-to-face discrete element method (DEM). The DEM is based on the discontinuity analysis which can consider anisotropic and discontinuous deformations due to joints and their orientations. It uses four lump-points at each surface of rock blocks to describe their interactions. The relationship between the critical excavation depth D-s and the natural slope angle alpha, the joint inclination angle theta as well as the strength parameters of the joints c(r) ,phi(r) is analyzed, and the critical excavation depth obtained with this DEM and the limit equilibrium method (LEM) is compared. Furthermore, effects of joints on the failure modes are compared between DEM simulations and experimental observations. It is found that the DEM predicts a lower critical excavation depth than the LEM if the joint structures in the rock mass are not ignored.

五轴框架式机器人激光加工系统 轨迹算法研究

在集成化智能激光加工系统工作原理的基础上提出了五轴机器人的激光加工轨迹算法。将三维离散数据点集拟合为空间参数曲面，在此参数曲面上规划五轴激光加工的等距轨迹。给出了冲压模具激光强化加工实例。取得了理想的加工效果。

三峡永久船闸高边坡开挖三维离散元数值模拟

采用面-面接触的三维离散元刚性块体模型，从实测节理面中取出其中的三组，按照其倾向、倾角和节理间距将三峡永久船闸未开挖的区域划分为10~5个离散单元，通过施加力边界条件，给出了与实测初始地应力场接近的数值模拟结果；然后，分4步模拟了永久船闸的开挖过程。计算结果表明：开挖过程会引起节理面出现张开趋势，个别岩体还会沿着节理面滑移。岩体位移的不对称现象较为自然地说明了由节理引起的岩体各向异性特征。

五轴框架式机器人激光加工系统轨迹算法研究

在集成化智能激光加工系统工作原理的基础上提出了五轴机器人的激光加工轨迹算法。将三维离散数据点集拟合为空间参数曲面，在此参数曲面上规划五轴激光加工的等距轨迹。给出了冲压模具激光强化加工实例，取得了理想的加工效果。

a real-time path planning approach without the computation of cspace obstacles

An important concept proposed in the early stage of robot path planning field is the shrinking of the robot to a point and meanwhile expanding of the obstacles in the workspace as a set of new obstacles. The resulting grown obstacles are called the Configuration Space (Cspace) obstacles. The find-path problem is then transformed into that of finding a collision free path for a point robot among the Cspace obstacles. However, the research experiences obtained so far have shown that the calculation of the Cspace obstacles is very hard work when the following situations occur: 1. both the robot and obstacles are not polygons and 2. the robot is allowed to rotate. This situation is even worse when the robot and obstacles are three dimensional (3D) objects with various shapes. Obviously a direct path planning approach without the calculation of the Cspace obstacles is strongly needed. This paper presents such a new real-time robot path planning approach which, to the best of our knowledge, is the first one in the robotic community. The fundamental ideas are the utilization of inequality and optimization technique. Simulation results have been presented to show its merits.

Study on Mechanics Parameters of Unloaded Rock Mass about the Underground Powerhouse of Jin-ping Hydroelectric Station

After the excavation of Jinping underground cavern, a strong expansion appears along the unloading direction of the rock mass, mainly in the type of tensile rupture, accompanied by shear destruction, unloading resulted in significant deterioration of mechanical properties of rock. Based on the in-site investigation of rock mass structure, via analyzing the acoustic testing data, we identify the unloading range of the side walls and the division of rock types, and carry out with the solution of rock mechanical parameters about different unloading zone, providing geological foundation for the supporting design of the following design of the side walls, at the same time, providing reference for the selection of mechanical parameters of other underground excavation engineering with similar geological conditions.

五轴磨抛机器人补偿算法研究与实现

通过分析基于模型的补偿方法和非模型补偿方法的优缺点,结合一个五轴磨抛机器人的结构特点,提出了两种补偿方法相结合的混合补偿算法.针对平移关节误差的主要来源难于建模的特点,采用非模型的方法进行补偿;针对转动关节误差主要来源为几何参数误差,能够建模,但有些参数随机器人末端位置不同而变化的特点,采用二者相结合的混合方法进行补偿.通过对该机器人系统的实验,验证了方法的有效性和可行性.

基于神经网络的机器人视觉伺服控制

视觉伺服可以应用于机器人初始定位自动导引、自动避障、轨线跟踪和运动目标跟踪等控制系统中。传统的视觉伺服系统在运行时包括工作空间定位和动力学逆运算两个过程,需要实时计算视觉雅可比矩阵和机器人逆雅可比矩阵,计算量大,系统结构复杂。本文分析了基于图像的机器人视觉伺服的基本原理,使用BP神经网络来确定达到指定位姿所需要的关节角度,将视觉信息直接融入伺服过程,在保证伺服精度的情况下大大简化了控制算法。文中针对Puma560工业机器人的模型进行了仿真实验,结果验证了该方法的有效性。

虚拟现实水下机器人仿真系统

本文采用VR技术,模拟真实情况建立了一个水下机器人仿真系统。该系统使用与真实系统相同的控制器和输入设备,提供操作员训练、人—机智能控制仿真、机器人轨迹规划仿真等功能,仿真数据能够引导真实机器人运动。文中以仿真实例说明了系统的有效性。

基于AFM的机器人化纳米操作系统综述

对基于扫描隧道显微镜(Scanning tunnel microscope,STM)及原子力显微镜(Atomicforcemicroscope,AFM)的纳米操作技术发展进行阐述,针对其中存在的主要问题,引述出机器人化纳米操作的必要性。接着,对国内外机器人化纳米操作系统的研究进展、现状及存在的主要问题进行详细分析,提出基于AFM的机器人化纳米操作系统的结构原型,并指出实现机器人化纳米操作所需解决的关键技术问题及相应的解决方案之一,为进行深入的机器人化纳米操作研究提供了可以借鉴的研究方向。

机器人化月表采样器的研制

首先介绍了月表采样的新特点与存在的困难;根据月表环境、月表样品的特点以及嫦娥三期工程中对月表采样的要求,合理地选择了采样方式,研制出了一台六自由度机器人化月表采样器,并且对采样器的采样原理,机械系统和运动原理做了详细的分析;最后在石灰粉上做了采样实验,验证了多功能的机器人化月表采样器的基本功能与可行性。

除草机器人机械臂的逆向求解与控制

设计了一种基于机器视觉导航和杂草识别的除草机器人模型,该机器人能沿作物行间自主行走并能准确地识别和"清除"杂草。设计了除草机器人的机械臂除草执行系统,求取了机械臂运动学逆解,用VC++开发了控制程序。试验显示,图像处理算法所需时间少,能够适应户外自然光线在一定范围的变化,机械臂能够平稳动作并精确定位杂草目标。