Compact Reconfigurable Binary-Decision-Diagram Logic Circuit on a GaAs Nanowire Network

We describe a reconfigurable binary-decision-diagram logic circuit based on Shannon's expansion of Boolean logic function and its graphical representation on a semiconductor nanowire network. The circuit is reconfigured by using programmable switches that electrically connect and disconnect a small number of branches. This circuit has a compact structure with a small number of devices compared with the conventional look-up table architecture. A variable Boolean logic circuit was fabricated on an etched GaAs nanowire network having hexagonal topology with Schottky wrap gates and SiN-based programmable switches, and its correct logic operation together with dynamic reconfiguration was demonstrated.

Compact four-channel reconfigurable optical add-drop multiplexer using silicon photonic wire

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide, which is controlled through the thermo-optic effect. The effective footprint of the device is about 1000 x 500 mu m(2). The minimum insertion loss including the transmission loss and coupling loss is about 10.7 dB. The tuning bandwidth is about 17 nm, the average tuning efficiency about 6.11 mW/nm and the tuning speed about 24.5 kHz. (c) 2009 Elsevier B.V. All rights reserved.

Four-channel reconfigurable optical add-drop multiplexer based on photonic wire waveguide

We designed and fabricated a four-channel reconfigurable optical add-drop multiplexer based on silicon photonic wire waveguide controlled through thermo-optic effect. The effective footprint of the device is about 1000 x 500 mu m(2). The minimum insertion loss is about 10.7 dB and the tuning bandwidth about 17 nm. The average tuning power efficiency is about 6.187 mW/nm and the tuning speed about 24.4 kHz. The thermo-optic polarization-rotation effect is firstly reported in this paper. (C) 2009 Optical Society of America

Four-channel reconfigurable optical add-drop multiplexer based on photonic wire waveguide: erratum

An erratum is presented to correct the calculation of the filtering bandwidth of the micro-ring resonator. (C) 2009 Optical Society of America

Novel compact SOI-based reconfigurable optical add/drop multiplexer using microring resonators - art. no. 60190L

Novel compact design for 4-channel SOI-based reconfigurable optical add/drop multiplexer using microring resonators is presented and analyzed. Microring resonators have two important attributes as a key new technology for future optical communications, namely functionality and compactness. Functionality refers to the fact that a wide range of desirable filter characteristics can be synthesized by coupling multiple rings. Compactness refers the fact that ring resonators with radii about 30 mu m can lead to large scale integration of devices with densities on the order of 10(4) similar to 10(5) devices per square centimeter. A 4-channel reconfigurable optical add/drop multiplexer comprises a grid-like array of ridge waveguides which perpendicularly cross through each other. SOI-based resonators consisted of multiple rings at each of the cross-grid nodes serve as the wavelength selective switch, and they can switch an optical signal between two ports by means of tuning refractive index of one of the rings. The thermo-optic coefficient of silicon is 1.86x 10(-4) /K. Thus a temperature rise of 27K will increase the refractive index by 5 x 10(-3), which is enough to cause the switching of our designed microring resonators. The thermo-optic effect is used to suppress the resonator power transfer, rather than to promote loss. Thus, the input signal only suffers small attenuation and simultaneously low crosstalk can be achieved by using multiple rings.

Reconfigurable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguide

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-06-04T07:40:23Z No. of bitstreams: 1 Reconfigurable Optical Add-Drop Multiplexer Based on Silicon Photonic Wire Waveguide.pdf: 416355 bytes, checksum: 5b80992194ba9fa818a011244cec6363 (MD5)

Compact four-channel reconfigurable optical add-drop multiplexer using silicon photonic wire (vol 282, pg 3477, 2009)

Submitted by 阎军 (yanj@red.semi.ac.cn) on 2010-04-04T06:57:43Z No. of bitstreams: 1 71.pdf: 92858 bytes, checksum: 2a0a4972af8e56b0fced818042dd6dbd (MD5)

基于Nios-Ⅱ用于加速器监控系统的通用型可重配置嵌入式微控制器

FPGA and dedicated micro-controller chips are widely used in HIRFL-CSR monitor and control systems.This paper discusses the characteristics of HIRFL-CSR s dedicated micro-controllers and it s requirement for micro-controllers. Using programmable technology and Nios-Ⅱ processor,we have designed and implemented a reconfigurable embedded micro(controller in altera cycloneⅡ2c35f484 FPGA. The micro-controller which has low hardware cost and 185 MHz maximum operating frequency can replace the dedicated micro-cont...中文文摘：讨论并参考了冷却储存环目前使用的专用微控制器的特点和其对微控制器的需求,采用可编程技术和Nios-Ⅱ处理器,在altera-cycloneII2c35f484芯片内实现可重构微控制器。该微控制器硬件资源消耗少,最大工作频率可达185MHz,可代替目前在监控系统中大量使用的专用微控制器芯片,减小硬件设计复杂度、节约成本。

一种可变形移动机器人协同构形变换方法

提出了一种可变形移动机器人AMOEBA-I的协同构形变换方法,建立了机器人系统的数学模型,对各个模块之间的协同变换及运动特性进行了分析.研究了机器人3个模块在协同变换过程中的电流变化情况,实现了3种特殊构形之间的变换.通过理论分析和实验比较了协同构形变换方法的特点,实验验证了在多种地面条件下机器人协同构形变换方法的有效性.

星球探测系统的多机器人组内协作研究

建立了子机器人的控制模型,提出了分散式控制与集中式控制相结合的复合控制体系。采用动态分配ID号和由ID号确定机器人组中领导者的机制,建立了有领导者的机器人组的协作方法。其中,领导者与监控平台之间采用无线通讯,机器人组内采用CAN(control area network)总线传递控制信号。同时采用组内基于状态表匹配的控制方式。两个机器人组合利用以上机制,通过相互协调完成差速转弯的实验验证了该控制方法的可行性。

一种FPGA的嵌入式可重构机器人控制系统

提出一种基于FPGA的可重构嵌入式微处理器控制系统.在FPGA中嵌入两个NiosⅡ软核,用VHDL语言编写用户自定义组件.在一个由NiosⅡ软核组成的处理器上实现PWM信号生成、编码器信号处理以及多电机同步伺服运算等,在另一个处理器实现机器人任务管理.该控制系统针对微小型爬壁机器人的控制系统设计,不仅具有良好的实时多任务处理能力,而且具有可重构的特点,因而可应用于一类微小型机器人控制系统以提高其设计的灵活性.

可变形机器人协同转向运动研究

可变形机器人AMOEBA-I具有多种构形和多种转向方式.为实现机器人转向性能的优化,提出了可变形机器人的协同转向方法,并建立了相应的数学模型,对不同构形下的协同转向方式进行了理论分析.设定了机器人三个模块在协同转向过程中的运动关系,在此基础上给出了可变形机器人协同转向性能的评价指标.通过理论和实验比较了不同构形下的协同转向方式,实验验证了协同转向方法的有效性.

基于状态构形矢量和状态构形矩阵的可重构模块星球机器人构形水

可重构模块星球机器人系统由母体和多个子机器人模块组成,单个模块可以独立运动和操作,多个模块可以重构组合成不同构形,模块采用非对称式轮手一体机构,具有姿态方位性和运动方向性,重构目的是组成在某种环境下更好地完成有向性运动的构形。基于此,提出矢量构形概念,将运动趋势方向和方位性融合到构形拓扑结构中。在模块矢量分析模型基础上,提出并构建状态构形矢量(State configuration vector,SCV)和状态构形矩阵(State configuration matrix,SCM),对非对称式单模块和整体构形的状态信息进行描述,同时支持预定义的数学变换操作,可以表达并触发模块的基础动作、构形重构。提出离散模块组合重构成目标构形的优化分析算法,通过实例仿真计算获得优化分析的选择结果。

可重构机器人越障运动的规划

提出一种新型的可重构机器人,该机器人在受一个驱动力矩的作用时,在不同约束下表现的输出形式不同.利用机构这一特点,实现了机器人移动中的自主越障运动.主要针对机器人越障运动中越障高度受导轮和手臂影响的问题,提出一种借助环境同时改变手臂姿态的越障规划方法,有效地提高了越障的高度.通过试验样机验证了规划方法的有效性.

模块化变形机器人非同构构形表达与计数

提出一种新型链式可重构模块机器人平台,该机器人平台具有手动可重构和自动变形的特点,介绍一种三模块变形机器人样机。组成机器人的单个模块可以简化为由模块本体、连接臂和偏置关节组成。模块的数量可以根据实际工作的需要进行选择,模块间的连接具有规则连接和非规则连接两种方式;同时,由连接模块的偏置关节的运动,模块间的相对位置可以改变。由于模块连接方式的不同和模块间相对位置的变化,变形机器人具有多种非同构构形;为此,根据模块的物理结构和邻接关系提出了用构形矩阵来表达机器人结构的拓扑信息,并在仿真环境下进行等效描述;提出基于组合计数原理的递归算法,用于多模块变形机器人的非同构构形的计数,并根据构形矩阵的拓扑信息对构形进行评价。最后根据仿真结果给出了一种三模块变形机器人样机对称构形的设计示例,验证了算法的可行性。