Structure tuning of line-defect waveguides based on silicon-on-insulator photonic crystal slabs

We present fabrication and experimental measurement of a series of photonic crystal waveguides. The complete devices consist of an injector taper down from 3 mu m into a triangular-lattice air-hole single-line-defect waveguide with lattice constant from 410nm to 470nm and normalized radius 0.31. We fabricate these devices on a siliconon-insulator substrate and characterize them using a tunable laser source over a wavelength range from 1510nm to 1640nm. A sharp attenuation at photonic crystal waveguide mode edge is observed for most structures. The edge of guided band is shifted about 30nm with the 10nm increase of the lattice constant. We obtain high-efficiency light propagation and broad flat spectrum response of the photonic crystal waveguides.

Tunable Fano resonance in photonic crystal slabs

A three dimensional analysis of a special class of anisotropic materials is presented. We introduce an extension of the Scattering Matrix Method (SMM) to investigate the behavior of anisotropic Photonic Crystal Slabs (PhCS) subject to external radiation. We show how the Fano effect can play a fundamental role in the realization of tunable optical devices. Moreover, we show how to utilize electron injection, electric field and temperature as parameters to control the Fano resonance shift in both isotropic and anisotropic materials as Si and Potassium Titanium Oxide Phosphate (KTP). We will see that because Fano modes are sensitive and controllable, a broad range of applications can be considered. (c) 2006 Optical Society of America

Design of Low Power Multi-Standard Active-RC Filter for WLAN and DVB-H

In this paper, a low-power, highly linear, integrated, active-RC filter exhibiting a multi-standard (IEEE 802.11a/b/g and DVB-H) application and bandwidth (3MHz, 4MHz, 9.5MHz) is present. The filter exploits digitally-controlled polysilicon resister banks and an accurate automatic tuning scheme to account for process and temperature variations. The automatic frequency calibration scheme provides better than 3% corner frequency accuracy. The Butterworth filter is design for receiver (WLAN and DVB-H mode) and transmitter (WLAN mode). The filter dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from 2.85-V supply. The dissipation of calibration consumes 2mA. The circuit has been fabricated in a 0.35um 47-GHz SiGe BiCMOS technology, the receiver and transmitter occupy 0.28-mm(2) and 0.16-mm(2) (calibration circuit excluded), respectively.

Experimental observation of negative lateral displacements of microwave beams transmitting through dielectric slabs

It was theoretically predicted that when a beam of light travels through a thin slab of optically denser medium in the air, the emerging beam from the slab will suffer a lateral displacement that is different from the prediction of geometrical optics, that is, the Snell's law of refraction and can be zero and negative as well as positive. These phenomena have been directly observed in microwave experiments in which large angles of incidence are chosen for the purpose of obtaining negative lateral displacements. (C) 2005 Elsevier B.V. All rights reserved.

A multi-standard active-RC filter with accurate tuning system

A low-power, highly linear, multi-standard, active-RC filter with an accurate and novel tuning architec-ture is presented. It exhibits 1EEE 802. 11a/b/g (9.5 MHz) and DVB-H (3 MHz, 4 MHz) application. The filter exploits digitally-controlled polysilicon resistor banks and a phase lock loop type automatic tuning system. The novel and complex automatic frequency calibration scheme provides better than 4 comer frequency accuracy, and it can be powered down after calibration to save power and avoid digital signal interference. The filter achieves OIP3 of 26 dBm and the measured group delay variation of the receiver filter is 50 ns (WLAN mode). Its dissipation is 3.4 mA in RX mode and 2.3 mA (only for one path) in TX mode from a 2.85 V supply. The dissipation of calibration consumes 2 mA. The circuit has been fabricated in a 0.35μm 47 GHz SiGe BiCMOS technology; the receiver and transmitter filter occupy 0.21 mm~2 and 0.11 mm~2 (calibration circuit excluded), respectively.

一种带有精准调谐结构的有源RC低通滤波器的设计

提出了一种带有精准调谐结构的有源RC低通滤波器的设计方案,其截止频率为5MHz,并在0.18μm标准CMOS工艺线上流片得到验证.调谐精度达到(-1.24%,+2.16%),测试中得到验证.调谐系统所占芯片面积仅为主滤波器面积的1/4.调谐系统完成调谐功能后会自动关闭,降低了功耗以及对主滤波器的串扰.以50Ω作为源阻抗,滤波器带内3阶交调量(IIP3)好于16.1dBm.滤波器输入参考噪声为36μVrms.滤波器群延迟时间波动测试结果为24ns.滤波器功耗为3.6mW.带有这种调谐结构的滤波器容易被实现,可以用于很多无线低中频应用中,例如全球定位系统、全球通和码分多址等芯片系统中.

Analysis of residual stress gradient in MEMS multi-layer structure

Residual stress and its gradient through the thickness are among the most important properties of as-deposited films. Recently, a new mechanism based on a revised Thomas-Fermi-Dirac (TFD) model was proposed for the origin of intrinsic stress in solid film

Effect of Cold Rolling Ratio and Heating Rate of Batch Annealing on Textures of Micro-Carbon Steel Sheet

在四辊冷轧试验机和Gleeble-1500试验机上进行了热轧微碳钢板的冷轧和退火试验。用D/max-RC衍射仪测量了试样的,/”层织构,并用Roe软件进行了ODF分析。研究表明,所研究的热轧微碳深冲板压下率约为75%,退火升温速度为20-40℃/h时,试样为{111}织构特征；压下率较大(80%)时,退火织构为较弱的{111}组分。无论{111}织构还是非{111}织构都是在形核阶段开始形成,在晶粒长大优先长大,受到定向形核和选择生长双重机制的作用。

The inner Pressure of the Atoms in a Solid in Refined TFD Theory

The relation between the inner pressure of an atom in a solid and the density of energy of electrons under Refined TFD theory is given.

Quantum Monte Carlo study of the CO interaction with a dimer model surface for Cr(110)

The chemisorption of CO on a Cr( 110) surface is investigated using the quantum Monte Carlo method in the diffusion Monte Carlo (DMC) variant and a model Cr2CO cluster. The present results are consistent with the earlier ab initio HF study with this model that showed the tilted/ near-parallel orientation as energetically favoured over the perpendicular arrangement. The DMC energy difference between the two orientations is larger (1.9 eV) than that computed in the previous study. The distribution and reorganization of electrons during CO adsorption on the model surface are analysed using the topological electron localization function method that yields electron populations, charge transfer and clear insight on the chemical bonding that occurs with CO adsorption and dissociation on the model surface.

测量光电流信号的一种简单方法

本文介绍用运算放大器和RC网络构成的带通滤波器测量光电信号及其结果,此方法简单易行,适当选择取样电阻,可使误差小于2％。

硼錳白口铸鉄的搪瓷鉄坯模具

<正> 我国日用搪瓷行业中的鉄坯延伸模具材料是生产中的一个难题。由于搪瓷鉄坯延伸模具的工作条件,要求材料应具有較高的整体硬度(RC 45左右),較好的韌性,能切削加工,要求不經热处理鑄态使用,而且要价格低廉。因对材料要求較高,所以各地搪瓷厂虽先后試用过高牌号灰鑄鉄、球墨鑄鉄及某些合金鑄

Parameter-transformation relations for traveling-wave solutions of kdv-burgers equation

 Burgers suggested that the main properties of free-turbulence in the boundless area without basic flow might be understood with the aid of the following equation, which was much simpler than those of fluid dynamics, 更多还原

飞秒强激光脉冲与氢团簇相互作用产生的最大质子能量与团簇尺寸的相关性

报道了飞秒强激光脉冲（60fs，790nm，2×10^16W／cm^2与纳米尺寸的氢团簇（半径rc约为1～3nm）相互作用，产生的最大质子能量Emax对于团簇半径rc相关性的实验研究结果。从激光-氢团簇相互作用产生的质子的飞行时间谱测量以及团簇尺寸的瑞利散射诊断结果，得到Emax与rc^2成线性正比关系，比例系数为0．75，与报道的理论模拟结果一致，表明氢团簇发生纯库仑爆炸。实验结果同时提示，进一步的理论模拟应考虑气体喷流中团簇的尺寸分布。

Nd：GGG激光晶体热容工作下的热致效应与冷却特性数值模拟

基于对称双侧激光二极管（LD）抽运Nd：GGG（掺钕钆镓石榴石）激光晶体板条，从热传导基本方程出发，以废热等效于内热源模型为前提，利用有限元分析软件ANSYS对Nd：GGG板条在热容工作下的瞬态温度场及应力场进行了数值模拟，分析了在不同边界条件下温度和应力随时间和空间的变化特性及其热致变形。计算结果表明：在激光发射阶段，边界非绝热使得板条在垂直光轴方向产生温度梯度，由此产生的折射率梯度和应力梯度导致距离光轴最远的板条边缘和光轴处产生约0．2μm的变形量。同时模拟了冷却阶段空气对流冷却、水循环冷却及喷雾冷却