Thermo-optic variable optical attenuator with low power consumption fabricated on silicon-on-insulator by anisotropic chemical etching

A thermo-optic Mach-Zehnder (MZ) variable optical attenuator based on silicon waveguides with a large cross section was designed and fabricated on silicon-on-insulator (SOI) wafer. Multimode interferometers were used as power splitters and combiners in the MZ structure. In order to achieve a smooth interface, anisotropic chemical etching of silicon was used to fabricate the waveguides. Isolating grooves were introduced to reduce power consumption and device length. The device has a low power consumption of 210 mW and a response time of 50 mus. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

1x8 cascaded multimode interference splitter in silicon-on-insulator

A cascaded multimode interference 1 x 8 power splitter is proposed and fabricated in silicon-on-insulator material. The device consists of seven 1 x 2 power splitters arranged in a tree configuration. The cascaded splitter and its 1 x 2 splitter element have the power uniformity of approximately 1.5 dB and 0.3 dB, respectively.

Fabrication of a 4x4 strictly nonblocking SOI switch matrix

A 4 x 4 strictly nonblocking thermo-optical switch matrix based on Mach-Zehnder (MZ) switching unit was designed and fabricated in silicon-on-insulator (SOI) wafer. The paired multi-mode interferometers (MMI) were used as power splitters and combiners in MZ structures. The device presents an average insertion loss of 17 dB and an average crosstalk of 16.5 dB. The power consumption needed for operation is reduced to 0.288 W by adding isolating trenches. The switching time of the device is about 15 mu s, which is much faster than that of silica-based switches. (C) 2005 Elsevier B.V. All rights reserved.

Thermo-optical switch matrix based on silicon-on-insulator waveguides

A thermo-optical waveguide switch matrix is designed and fabricated on silicon-on-insulator wafer. Multi-mode interferometers are used as power splitters and combiners in a Mach-Zehnder structure. Inductively coupled plasma reactive ion etching is used to fabricate the waveguides. The rise and fall times of the switch matrix are 13 mu s and 7 mu s, respectively. Switch cells have an average switching power consumption of 340 mW.

Silicon-on-insulator based 2 x 2 multimode interference coupler with large tolerance

We demonstrate a type of 2 x 2 multimode interference 3 dB coupler based on silicon-on-insulator. The fabrication tolerance was investigated by the effective index method and the guide mode method. The devices with different lengths were fabricated and near-held output images were obtained. Tolerances to width, length and etch depth are 2, 200 and 2 mum, respectively. The devices show a uniform power distribution.

Integrated MMI optical couplers and optical switches in Silicon-on-insulator technology

Integrated multimode interference coupler based on silicon-on-insulator has been become a kind of more and more attractive device in optical systems. Thin cladding layers (<1.0mum) can be used in SOI waveguide due to the large index step between Si and SiO2, making them compatible with the VLSI technology. Here we demonstrate the design and fabrication of multimode interference (MMI) optical couplers and optical switches in SOI technology.

Integrated multimode interference couplers in silicon-on insulator

Silicon-on insulator (SOI) is an attractive platform for the fabrication of optoelectronic integrated circuit. Thin cladding layers (< 1.0m) can be used in SOI waveguide due to the large index step between Si and SiO2, making them compatible with the VLSI technology. Here we demonstrate the fabrication of 1 x 4 and 2 x 2 multimode interference (MMI) coupler based on SOI technology. Performances of the devices are analyzed. The minimum excess loss of the devices is about 1.8dB. The devices show uniform power distribution.

AIGaN/GaN HEMTs Power Amplifier MIC with Power Combining at C-Band

A power amplifier MIC with power combining based on AlGaN/GaN HEMTs was fabricated and measured. The amplifier consists of four 10×120μm transistors. A Wilkinson splitters and combining were used to divide and combine the power. By biasing the amplifier at V_(DS) =40V, I(DS)= 0. 9A, a maximum CW output power of 41. 4dBm with a maximum power added efficiency (PAE) of 32. 54% and a power combine efficiency of 69% was achieved at 5. 4GHz.

Two-dimensional simulation of an electron cyclotron resonance plasma source with self-consistent power deposition

Using a refined two-dimensional hybrid-model with self-consistent microwave absorption, we have investigated the change of plasma parameters such as plasma density and ionization rate with the operating conditions. The dependence of the ion current density and ion energy and angle distribution function at the substrate surface vs. the radial position, pressure and microwave power were discussed. Results of our simulation can be compared qualitatively with many experimental measurements.

Experimental Validation of Improving Aircraft Rolling Power Using Piezoelectric Actuators

Piezoelectric actuators are mounted on both sides of a rectangular wing model. Possibility of the improvement of aircraft rolling power is investigated. All experiment projects, including designing the wind tunnel model, checking the material constants, measuring the natural frequencies and checking the effects of actuators, guarantee the correctness and precision of the finite element model. The wind tunnel experiment results show that the calculations coincide with the experiments. The feasibility of fictitious control surface is validated.

Improvement of Aircraft Rolling Power by Use of Piezoelectric Actuators

Piezoelectric actuators are distributed on both side of a rectangular wing model,and the possibility of improvement of aircraft rolling power is investigated. The difference between the model with aileron deflection and the model without aileron (fictitious control surface, FCS) is studied. The analytical results show that these two cases are substantial different. In aileron deflection case, the aeroelastic effect is disadvantageous, so the structural stiffness should be high until the electrical voltage is not necessary. But in the case of FCS,the aeroelastic effect is advantageous and it means that lower structural stiffness can lead to lower voltage. Compared with aileron project, the FCS project can save structure weight.

Scaling relationships in indentation of power-law creep solids using self-similar indenters

We use dimensional analysis to derive scaling relationships for self-similar indenters indenting solids that exhibit power-law creep. We identify the parameter that represents the indentation strain rate. The scaling relationships are applied to several types of indentation creep experiment with constant displacement rate, constant loading rate or constant ratio of loading rate over load. The predictions compare favourably with experimental observations reported in the literature. Finally, a connection is found between creep and 'indentation-size effect' (i.e. changing hardness with indentation depth or load).

High-power laser beam shaping by inseparable two-dimensional binary-phase gratings for surface modification of stamping dies

For surface modification of stamping dies, an inseparable two-dimensional binary-phase gratings is introduced to implement the wavefront transformation of high-power laser beams. The design and fabrication of the gratings are described in detail. Two-dimensional even sampling encoding scheme is adopted to overcome the limitations of conventional Dammann grating in the design of two-dimensional output patterns. High diffractive efficiency (>70%) can be achieved through the transformation of the Gaussian laser beam into several kinds of two-dimensional arrays in focal plan. The application of the binary-phase gratings in the laser surface modification of ductile iron is investigated, and the results show that the hardness and the wear resistance of the sample surface were improved significantly by using the binary-phase gratings. (C) 2008 Elsevier Ltd. All rights reserved.

Thermal fatigue on pistons induced by shaped high power laser. Part I: Experimental study of transient temperature field and temperature oscillation

Thermal fatigue behavior is one of the foremost considerations in the design and operation of diesel engines. It is found that thermal fatigue is closely related to the temperature field and temperature fluctuation in the structure. In this paper, spatially shaped high power laser was introduced to simulate thermal loadings on the piston. The incident Gaussian beam was transformed into concentric multi-circular beam of specific intensity distribution with the help of diffractive optical element (DOE), and the transient temperature fields in the piston similar to those under working conditions could be achieved by setting up appropriate loading cycles. Simulation tests for typical thermal loading conditions, i.e., thermal high cycle fatigue (HCF) and thermal shock (or thermal low cycle fatigue, LCF) were carried out. Several important parameters that affect the transient temperature fields and/or temperature oscillations, including controlling mode, intensity distribution of shaped laser, laser power, temporal profile of laser pulse, heating time and cooling time in one thermal cycle, etc., were investigated and discussed. The results show that as a novel method, the shaped high power laser can simulate thermal loadings on pistons efficiently, and it is helpful in the study of thermal fatigue behavior in pistons. (C) 2007 Elsevier Ltd. All rights reserved.