Characterization of silicon carbide thin films and their use in colour sensor

A series of hydrogenated amorphous silicon carbide (a-Si1-xCx:H) films were prepared by plasma-enhanced chemical vapour deposition (PECVD) using a gas mixture of silane, methane, and hydrogen as the reactive source. The previous results show that a high excitation frequency, together with a high hydrogen dilution ratio of the reactive gases, allow an easier incorporation of the carbon atoms into the silicon-rich a-Si1-xCx:H film, widen the valence controllability. The data show that films with optical gaps ranging from about 1.9 to 3.6 eV could be produced. In this work the influence of the hydrogen dilution ratio of the reactive gases on the a-Si1-xCx:H film properties was investigated. The microstuctural and photoelectronic properties of the silicon carbide films were characterized by Rutherford backscattering spectrometry (RBS), elastic recoil detection analysis (ERDA), and FT-IR spectrometry. The results show that a higher hydrogen dilution ratio enhances the incorporation of silicon atoms in the amorphous carbon matrix for carbon-rich a-Si1-xCx:H films. One pin structure was prepared by using the a-Si1-xCx:H film as the intrinsic layer. The light spectral response shows that this structure fits the requirement for the top junction of colour sensor. (c) 2004 Elsevier B.V. All rights reserved.

己酸乙酯酯化真菌筛选及发酵条件研究

本文主要研究了具有己酸乙酯酯化活性的真菌菌株的筛选和发酵条件优化。从大曲和糟醅样品中分离纯化获得79株产生透明圈的丝状真菌，菌落形态初步识别结果显示分离菌株包括红曲霉属、根霉属及曲霉属等菌株。其中菌株EM-56酯化酶活力最强，发酵获得的粗酶制剂酶活为172.36 u。根据显微形态、菌落形态及生理生化特征，初步鉴定该菌株为曲霉科红曲霉属紫色红曲霉（Monascus purpureus）。 在此基础上重点研究了菌株EM-56在不同培养基成分及不同培养条件下的产酶情况，确定了最佳培养基和培养条件。通过单因素实验确定在基础培养基中添加最佳碳源为葡萄糖，最佳氮源为蛋白胨。正交优化实验结果确定了最佳培养基组成：以麸皮为基础培养基，添加葡萄糖 2%，蛋白胨 0.3 %，KH2PO4.3H2O 0.05 %，MgSO4.7H2O 0.06 %。菌株EM-56在上述培养基中的最佳发酵条件为：初始pH 5.5，发酵温度为35°C，发酵时间7d，种龄48h，接种量8%，装瓶量50g / 瓶（500mL）。在最佳培养基和发酵条件下，菌株EM-56发酵获得的粗酶制剂酶活达到241.56 u，比优化前提高了40.15%。 In this paper, the research focuses on the selection of fungus with esterifying activity and optimization of fermentation conditions. We isolated 79 strains which had transparent zones from Daqu and fermented grains. The isolated strains contained Monascus、Rhizopus and Aspergillus through primary morphology analysis. The strain of EM-56 which produces strongest esterase was selected. The enzyme activity reached 172.36u. According to related literature, EM-56 was identified as Monascus purpureus through morphology analysis and biochemical determination. We also studied the effects of different medium and fermentation conditions on the esterase production of strain EM-56. The optimal medium and fermentation conditions were determined. Single factor experiment result shows that the optimal carbon source added is glucose and the optimal nitrogen source added is peptone. The optimal fermentation medium determined by orthogonal optimization test is as follows: wheat bran as substrate, glucose 2%, peptone 0.3%, KH2PO4.3H2O 0.05%，MgSO4.7H2O 0.06%. The optimal fermentation conditions are: initial pH 5.5, cultural temperature 35°C, cultural time 7d, seed age 48h, inoculation 8%, medium mass 50g / flask（500mL）. The esterse activity of EM-56 cultivated in the optimal medium and fermentation conditions reached 241.56u and increased by 40.15% compared with the original activity.

两株耐碱性木聚糖酶产生菌的筛选及产酶条件研究

本文主要研究了从造纸厂碱性土壤中筛选得到的，能够产生耐碱木聚糖酶的两株放线菌X24-14和X15-17。通过16 S rRNA基因序列分析并结合菌株的形态特征以及生理生化特性，初步认为菌株X15-17为拟诺卡氏菌属（Nocardiopsis）的一个潜在新种；菌株X24-14为纤维化纤维菌（Cellulosimicrobium cellulans）。 在此基础上探索了菌株X24-14和菌株X15-17所产木聚糖酶的基本酶学性质。研究发现，两株菌所产的木聚糖酶的耐碱性均较强： 1）菌株X24-14所产的木聚糖酶，在pH 4.2～9.4的范围内能维持较高的活力，pH 9.4条件下，仍能保持80％的酶活力；2）菌株X15-17所产的木聚糖酶在pH 4.0～9.0的范围内能维持较高的活力，pH 9.0条件下，仍能保持80％的酶活力；3）两株菌所产的木聚糖酶均具有较好的pH稳定性，在pH 2.0～11.0范围内稳定，pH 11.0、4 ℃条件下处理24 h仍具有75％的活力。 本文还重点研究了菌株X24-14在不同培养基成分及不同培养条件下的产酶情况，确定了其适宜的产酶条件。结果显示，菌株X24-14的最适碳源为麸皮；最适氮源为蛋白胨；最适产酶pH为pH 8.5。菌株X24-14适宜的产酶条件为：麸皮60 g/L，蛋白胨10 g/L，K2HPO4 7.0 g/L，pH 8.5，接种量为5％，37 ℃，200 r/min发酵培养108 h。 Two strains of actinomycetes, X24-14 and X15-17, which produced alkali-tolerant xylanase were screened from the soil samples collected from a pulp mill in china. Based on the morphological, physiochemical characteristics and 16S rRNA sequence, X24-14 was priminarily identified as cellulosimicrobium cellulans ; X15-17 was priminarily identified as a new species of Nocardiopsis. The investigation examined the enzyme activities which produced by X24-14 and X15-17 under different pH and different temperatures. The results showed that : 1）The xylanase from X24-14 had characteristic of alkali-tolerance: It remains 80% relative activity at pH ranges between pH 4.2 and pH 9.4 under 50℃. 2)The xylanase from X15-17 also showed characteristic of alkali-tolerance, it remains 80% relative activity at pH ranges between pH 4.0and pH 9.0 under 50℃. 3）The xylanase from the two strains showed alkali-stable characteristics. They were stable at pH ranges between pH 2.0 and pH 11.0, showing 75% of its maximal activity remaining under 24 hours of treatment at 4℃. We also studied the effect of different growth conditions: carbon source, nitrogen sources, inoculum size, and initial pH on the production of xylanase of strain X24-14. The results showed that :The optimal carbon source was wheat bran; The optima nitrogen source was peptone; The maximum xylanase activity was achieved in the medium containing 60 g/L wheat bran, 10 g/L peptone, 7 g/L K2HPO4, inoculum size 5% and pH 8.5, under 37℃ in 108 h.

An optimal theory for an expansion of flow quantities to capture the flow structures

An optimal theory on how database analysis to capture the flow structures has been developed in this paper, which include the POD method as its special case. By means of the remainder minimization method in the Sobolev space, for more general optimal conditions the new theory has the potential to overcome an inherent limitation of the POD method, i.e., it cannot be used to the situations in which the optimal condition is other than the inner product global one. As an example, using the new theory, the database of a two-dimensional flow over a backward-facing step is analyzed in detail, with velocity and vorticity bases.

Characterization of a multi-keV x-ray source produced by nanosecond laser irradiation of a solid target: The influence of laser focus spot and target thickness

The influence of focus spot and target thickness on multi-keV x-ray sources generated by 2 ns duration laser heated solid targets are investigated on the Shenguang II laser facility. In the case of thick-foil targets, the experimental data and theoretical analysis show that the emission volume of the x-ray sources is sensitive to the laser focus spot and proportional to the 3 power of the focus spot size. The steady x-ray flux is proportional to the 5/3 power of the focus spot size of the given laser beam in our experimental condition. In the case of thin-foil targets, experimental data show that there is an optimal foil thickness corresponding to the given laser parameters. With the given laser beam, the optimal thin-foil thickness is proportional to the -2/3 power of the focus spot size, and the optimal x-ray energy of thin foil is independent of focus spot size. (C) 2008 American Institute of Physics.

In situ synthesis of ZrO2/ZrW2O8 composites with near-zero thermal expansion

In this paper, ZrO2 and WO3 were used as the raw materials to prepare ZrO2/ZrW2O8 composites by in situ reaction method and the thermal expansion property of the composites was studied. This novel method included a heating step up to 1473 K for 24 h, which combines the synthesizing and sintering of ZrW2O8. The result indicates that ZrO2/ZrW2O8 composite shows near-zero thermal expansion when the weight ratio of ZrO2 and WO3 is 2.5:1. Compared with composites prepared previously by non-reactive sintering of ZrO2 and ZrW2O8, the composites show higher relative density and lower porosity.

Highly efficient photoluminescence of Er2SiO5 films grown by reactive magnetron sputtering method

E2SiO5 thin films were fabricated on Si substrate by reactive magnetron sputtering method with subsequent annealing treatment. The morphology properties of as-deposited films have been studied by scanning electron microscope. The fraction of erbium is estimated to be 23.5 at% based on Rutherford backscattering measurement in as-deposited Er-Si-O film. X-ray diffraction measurement revealed that Er2SiO5 crystalline structure was formed as sample treated at 1100 degrees C for 1 h in O-2 atmosphere. Through proper thermal treatment, the 1.53 mu m Er3+-related emission intensity can be enhanced by a factor of 50 with respect to the sample annealed at 800 degrees C. Analysis of pump-power dependence of Er3+ PL intensity indicated that the upconversion phenomenon could be neglected even under a high photon flux of 10(21) (photons/cm(2)/sec). Temperature-dependent photoluminescence (PL) of Er2SiO5 was studied and showed a weak thermal quenching factor of 2. Highly efficienct photoluminescence of Er2SiO5 films has been demonstrated with Er3+ concentration of 10(22)/cm(3), and it opens a promising way towards future Si-based light source for Si photonics. (C) 2009 Elsevier B.V. All rights reserved.

Influence of AlN Buffer Thickness on GaN Grown on Si(111) by Gas Source Molecular Beam Epitaxy with Ammonia

Hexagonal GaN is grown on a Si(111) substrate with AlN as a buffer layer by gas source molecular beam epitaxy (GSMBE) with ammonia. The thickness of AlN buffer is changed from 9 to 72 nm. When the thickness of AlN buffer is 36 nm, the surface morphology and crystal quality of GaN is optimal. The in-situ reflection high energy electron diffraction (RHEED) reveals that the transition to a two-dimensional growth mode of AlN is the key to the quality of GaN. However, the thickness of AlN buffer is not so critical to the residual in-plane tensile stress in GaN grown on Si(111) by GSMBE for AlN thickness between 9 to 72 nm.

Influence of rapid thermal annealing on the optical properties of gallium nitride grown by gas-source molecular-beam epitaxy

Raman scattering, photoluminescence (PL), and nuclear reaction analysis (MA) have been employed to investigate the effects of rapid thermal annealing (RTA) on GaN films grown on sapphire (0001) substrates by gas-source molecular-beam epitaxy, The Raman spectra showed the presence of the E-2 (high) mode of GaN and shift of this mode from 572 to 568 cm(-1) caused by annealing. The results showed that RTA has a significant effect on the strain relaxation caused by the lattice and thermal expansion misfit between the GaN epilayer and the substrate. The PL peak exhibited a blueshift in its energy position and a decrease in the full width at half maximum after annealing, indicating an improvement in the optical quality of the film. Furthermore, a green luminescence appeared after annealing and increased in intensity with increasing annealing time. This effect was attributed to H concentration variation in the GaN film, which was measured by NRA. A high H concentration exists in as-grown GaN, which can neutralize the deep level, and the H-bonded complex dissociates during RTA, This leads to the appearance of a luminescent peak in the PL spectrum. (C) 1998 American Institute of Physics.

Some properties of gallium nitride films grown on (0001) oriented sapphire substrates by gas source molecular beam epitaxy

The Raman and photoreflectivity spectra of gallium nitride (GaN) films grown on (0001) oriented sapphire substrates by gas source molecular beam epitaxy (GSMBE) have been investigated. The Raman spectra showed the presence of the E-2(high) mode and a shift in the wavenumber of this mode with respect to the GaN epilayer thickness. The Raman scattering results suggest the presence of stress due to lattice and thermal expansion misfit in the films, and also indicate that the buffer layer play an important role in the deposition of high quality GaN layers. The residual stress changes from tensile to compressive as the epilayer thickness increases. Samples subjected to anneal cycles showed an increase in the mobility due probably to stress relaxation as suggested by an observed shift in the E-2(high) mode in the Raman spectra after annealing.

NADPH oxidase-mediated generation of reactive oxygen species: A new mechanism for X-ray-induced HeLa cell death

Oxidative damage is an important mechanism in X-ray-induced cell death. Radiolysis of water molecules is a source of reactive oxygen species (ROS) that contribute to X-ray-induced cell death. In this study, we showed by ROS detection and a cell survival assay that NADPH oxidase has a very important role in X-ray-induced cell death. Under X-ray irradiation, the upregulation of the expression of NADPH oxidase membrane Subunit gp91(phox) was dose-dependent. Meanwhile, the cytoplasmic subunit p47(phox) was translocated to the cell membrane and localized with p22(phox) and gp91(phox) to form reactive NADPH oxidase. Our data Suggest, for the first time, that NADPH oxidase-mediated generation of ROS is an important contributor to X-ray-induced cell death. This suggests a new target for combined gene transfer and radiotherapy.

Photo-induced reactions in the ion-molecule complex Mg+-OCNC2H5

Ion - molecule complexes of magnesium cation with ethyl isocyanate were produced in a laser- ablation supersonic expansion nozzle source. Photo- induced reactions in the 1: 1 complexes have been studied in the spectral range of 230 - 410 nm. Photodissociation mass spectrometry revealed the persistent product Mg+ from nonreactive quenching throughout the entire wavelength range. As for the reactive channels, the photoproducts, Mg+OCN and C2H5+, were produced only in the blue absorption band of the complex with low yields. The action spectrum of Mg+(OCNC2H5) consists of two pronounced peaks on the red and blue sides of the Mg+ 3(2)P <-- 3(2)S atomic transition. The ground state geometry of Mg+ - OCNC2H5 was fully optimized at B3LYP/6- 31 - G** level by using GAUSSIAN 98 package. The calculated absorption spectrum of the complex using the optimized structure of its ground state agrees well with the observed action spectrum. Photofragment branching fractions of the products are almost independent of the photolysis photon energy for the 3P(x,y,z) excitations. The very low branching ratio of reactive products to nonreactive fragment suggests that evaporation is the main relaxation pathway in the photo- induced reactions of Mg+ (OCNC2H5). (C) 2003 American Institute of Physics.

A simple selenium source to synthesize CdSe via the two-phase thermal approach

A novel selenium source was developed to synthesize the size-controlled CdSe nanocrystals with relatively narrow size distribution successfully in a two-phase thermal approach. A highly reactive and aqueous soluble selenium source was provided by the reduction of selenite, and in this route the size of the nanocrystals can be adjusted by the reaction temperature and time. The size, crystalline structure and optical characteristics of these nanocrystals were investigated by transmission electron microscopy, X-ray powder diffraction, X-ray photoelectron spectroscopy, UV-vis spectroscopy, and photoluminescence spectroscopy. The influence factors for this approach were also discussed.