Modeling and Simulation of Liquid Pulsed Particulate Fluidized Beds

Pulsed fluidization is of considerable interest in process engineering for improving fluidization quality. Quantitative understanding of the pulsed two-phase flow behaviors is very important for proper design and optimum operation of such contactors. The

Study on Microstructure and Nanomechanics Properties of Antibacterial Bone China

Fracture appearance, surface and nanomechanics properties of antibacterial ceramics contairing rare earth phosphate composite antibacterial materials were characterized and measured by SEM, AFM and Nanoindenter, respectively. Results show that grain of fracture surface of antibacterial ceramics grows uniform refinement topography of bubble break-up appears at the surface, which is flat and has liquid character, by adding the phosphate composite containing rare earth, nevertheless needle-like crystal and granular outgrowth form at fracture surface and surface of common ceramics, respectively. Young's modulus of antibacterial ceramic film is 74. 397 GPa and hardness is 8. 134 GPa, which increses by 4.4﹪ and 1.6﹪ comparing with common ceramics, respectively. Loading curves of two kind of ceramics have obvious nonlinear character under 700 nm and linear character between 700 ～ 1000 nm, and unloading curve have obvious linear character.

Orientation preference and fractal character of short fatigue cracks in a weld metal

Short fatigue crack behaviour in a weld metal has been further investigated. The Schmid factor and the fractal dimension of short cracks on iso-stress specimens subjected to reversed bending have been determined and then applied to account for the distribution and orientation characteristics of short fatigue cracks. The result indicates that the orientation preference of short cracks is attributed to the large values of Schmid factor at relevant grains. The Schmid factors of most slip systems, which produced short cracks, are less than or equal to 0.4. Crack length measurements reveal that short crack path, compared to that of long crack, possesses a more stable and relatively larger value of fractal dimension. This is regarded as one of the typical features of short cracks.

外部流场对激光加热运动目标影响的数值模拟

考虑激光与运动目标相互作用的基础上。利用有限元方法分析了亚声速条件下运动目标在激光辐照全过程的温度场和热应力场的分布与演化规律。结果表明：高速流场的存在，导致了明显的冷却效应；加热过程中目标材料出现了屈服，导致激光熄灭后结构内出现残余应力和变形；激光辐照区边缘产生很高的温度梯度和应力梯度，并且由于气流影响，受辐照区域前后两端应力分布不对称。

负啁啾高强度飞秒脉冲在正常色散材料中传输特性研究

利用块状正常色散材料作非线性介质，实验研究了负啁啾强激光飞秒脉冲在正常色散材料的传输过程中，脉冲波形及频谱随入射脉冲能量的变化特性．实验发现，负啁啾脉冲经过材料后激光光谱在被整形和压缩的同时，脉冲宽度也被压缩．实验获得的压缩脉冲宽度短于相等光谱宽度下的双曲正割转换极限脉冲宽度。数值模拟结果显示，在实验条件下模拟结果具有同样的变化特性．

强激光在窄通道中传播的理论研究

在考虑相对论和有质动力非线性以及全局电量守衡的前提下，分析了强激光在冷等离子体窄通道中稳定传播的情况。采用较为简化的二维理论模型，给出了描述激光和通道横向结构的解，对不同通道宽度、通道密度、激光强度和电磁模式等进行了讨论，分析了其对激光在等离子体通道中传播的影响。分析发现，在存在预通道的情况下，当等离子体通道的密度大于临界密度很多时（例如20倍临界密度），即使是在激光波长量缴的通道中，激光仍然可以传播。通道越宽，等离子体密度越小；激光强度越大越容易传播。在同样的通道和传输情况下，TE0模传输所需要的激光强

体布拉格光栅外腔半导体激光器光谱特性研究

用体布拉格光栅(VBG)作为反馈元件与瓦级半导体激光器(LD)以及快轴准直柱透镜构成一个可以将半导体激光器的工作波长稳定在体布拉格光栅布拉格波长处的外腔激光器。测量了体布拉格光栅外腔激光器的波长稳定性与其工作电流、热汇温度、激光束准直装置等因素的关系。分析了波长稳定效果与半导体激光器增益谱特性、外腔结构参量等因素的关系。研究表明,在相同的工作电流、热汇温度下,当准直柱透镜直径为0.4 mm时的波长稳定效果较好;在此情况下,当热汇温度控制在30 ℃,工作电流从0.5 A增加到1.5 A的测量范围内,以及当工