Influence of growth parameters of frequency-radio plasma nitrogen source on extending emission wavelengths from 1.31 mu m to 1.55 mu m GaInNAs/GaAs quantum wells grown by molecular-beam epitaxy

High (42.5%) indium content GaInNAs/GaAs quantum wells with room temperature emission wavelength from 1.3 mu m to 1.5 mu m range were successfully grown by Radio Frequency Plasma Nitrogen source assisted Molecular Beam Epitaxy. The growth parameters of plasma power and N-2 How rate were optimized systematically to improve the material quality. Photoluminescence and transmission electron microscopy measurements showed that the optical and crystal quality of the 1.54 mu m GaInNAs/GaAs QWs was kept as comparable as that in 1.31 mu m.

Effects of nitrogen source and concentration on growth rate and fatty acid composition of Ellipsoidion sp (Eustigmatophyta)

In order to study the effects of different nitrogen source and concentration on the growth rate and fatty acid composition, a marine microalga Ellipsoidion sp. with a high content of eicosapentaenoic acid (EPA) was cultured in media with different nitrogen sources and concentrations. During the pre-logarithmic phase, the alga grew faster with ammonium as N source than with nitrate, but the reverse applied during the post-logarithmic phase. The alga grew poorly in N-free medium or medium with urea as the sole N source. In the same growth phase, ammonium medium resulted in higher yield of total lipid, but the EPA yield did not differ significantly different from that using nitrate medium. The maximum growth rate occurred in medium containing 1.28 mmol L-1 sodium nitrate, while maximum EPA and total lipid contents were reached at 1.92 mmol L-1, when EPA accounted for 27.9% total fatty acids. The growth rate kept stable when NH4Cl ranged from 0.64 to 2.56 mmol L-1, and the maximum content of total lipid and EPA occurred in the medium with 2.56 mmol L-1 NH4Cl. The EPA content was higher in the pre- than post-logarithmic phase, though the total lipid content was lower. The highest EPA content expressed as percent total fatty acid was 27.9% in nitrate medium and and 39.0% in ammonium medium.

GaN epilayers grown at high growth rate using gas source molecular beam epitaxy method

High-quality GaN epilayers have been grown by gas source molecular beam epitaxy using ammonia as the nitrogen source. During the growth, the growth rate is up to 1.2 mu m/h and can be varied from 0.3 to 1.2 mu m. The unintentional n-type doping as low as 7x10(17) cm(-3) was obtained at room temperature. Low-temperature photoluminescence spectrum was dominated by near-edge emission without deep-level related luminescence, indicative of high-quality epilayers. (C) 1998 Elsevier Science B.V. All rights reserved.

Properties of GaN epilayers with various growth conditions grown by gas source molecular beam epitaxy

GaN epilayers on sapphire (0001) substrates were grown by the gas source molecular beam epitaxy (GSMBE) method using ammonia (NH,) gas as the nitrogen source. Properties of gallium nitride (GaN) epilayers grown under various growth conditions were investigated. The growth rate is up to 0.6 mu m/h in our experiments. Cathodoluminescence, photoluminescence and Hall measurements were used to characterize the films. It was shown that the growth parameters have a significant influence on the GaN properties. The yellow luminescence was enhanced at higher growth temperature. And a blue emission which maybe related to defects or impurity was observed. Although the emission at 3.31 eV can be suppressed by a low-temperature buffer layer, a high-quality GaN epilayer can be obtained without the buffer layer. (C) 1998 Elsevier Science B.V. All rights reserved.

Nitrite utilization by Chaetoceros muelleri under elevated CO2 concentration

Chaetoceros muelleri (Lemn.) was cultured with nitrite (NO2-) or nitrate (NO3-) as the sole nitrogen source and aerated with air or with CO2-enriched air. Cells of C. muelleri excreted into the medium nitrite produced by reduction of nitrate when grown with 100 mu M NaNO3 as nitrogen source. Accordingly, NO2- concentration reached 10.4 mu M after 95 h at the low CO2 condition (aerated with air); while the maximum NO2- concentration was only around 2.0 mu M at the high CO2 condition (aerated with 5% CO2 in air), furthermore, after 30 h it decreased to no more than 1.0 mu M. NO2- was almost assimilated in 80 h when C. muelleri was cultured at the high CO2 condition with 100 mu M NaNO2 as sole nitrogen source. At the high CO2 condition, after 3 h the activity of nitrite reductase was as much as 50% higher than that at the low CO2 condition. It was indicated that enriched CO2 concentration could inhibit nitrite excretion and enhance nitrite assimilation by cells. Therefore, aeration with enriched CO2 might be an effective way to control nitrite content in aquaculture systems.

alr0117, a two-component histidine kinase gene, is involved in heterocyst development in Anabaena sp PCC 7120

Anabaena sp. PCC; 7120 was mutagenized by transposon Tn5-1087b, generating a mutant whose heterocysts lack the envelope polysaccharide layer. The transposon was located between nucleotides 342 and 343 of alr0117, a 918 bp gene encoding a histidine kinase for a two-component regulatory system. Complementation of the mutant with a DNA fragment containing alr0117 and targeted inactivation of the gene confirmed that alr0117 is involved in heterocyst development. RT-PCR showed that alr0117 was constitutively expressed in the presence or absence of a combined-nitrogen source. hepA and patB, the two genes turned on during wild-type heterocyst development, were no longer activated in an alr0117-null mutant. The two-component signal transduction system involving alr0117 may control the formation of the envelope polysaccharide layer and certain late events essential to the function of heterocysts.

ECR plasma in growth of cubic GaN by low pressure MOCVD

To heteroepitaxally grow the crystalline cubic-GaN (c-GaN) film on the substrates with large lattice mismatch is basically important for fabricating the blue or ultraviolet laser diodes based on cubic group III nitride materials. We have obtained the crystalline c-GaN film and the heteroepitaxial interface between c-Gan and GaAs (001) substrate by the ECR Plasma-Assisted Metal Organic Chemical Vapor Deposition (PA-MOCVD) under low-pressure and low-temperature (similar to600degreesC) on a homemade ECR-plasma Semiconductor Processing Device (ESPD). In order to decrease the growth temperature, the ECR plasma source was adopted as the activated nitrogen source, therefore the working pressure of MOCVD was decreased down to the region less than 1 Pa. To eliminate the damages from energetic ions of current plasma source, a Multi-cusp cavity,coupling ECR Plasma source (MEP) was selected to use in our experiment. To decrease the strain and dislocations induced from the large lattice mismatch between c-GaN and GaAs substrate, the plasma pretreatment procedure i.e., the initial growth technique was investigated The experiment arrangements, the characteristics of plasma and the growth procedure, the characteristics on-GaN film and interface between c-GaN and GaAs(001), and the roles of ECR plasma are described in this contribution.

GaInNAs/GaAs multiple-quantum well resonant-cavity-enhanced photodetectors at 1.3 mu m

A GaInNAs/GaAs multiple quantum well (MQW) resonant-cavity enhanced photodetector (RCF-PD) operated at a wavelength of 1.3 mum with the full width at half maximum of 4nm has been demonstrated. The GaInNAs RCE - PD was grown by molecular beam epitaxy using a homemade ion-removed dc plasma cell as a nitrogen source. GaInNAs/GaAs MQW shows a strong exciton peak at room temperature, which is very beneficial for applications in long-wavelength absorption devices. For a 100 mum diameter RCE-PD, the dark current is 20 and 32 pA at biases of 0 and 6 V, respectively, and the breakdown voltage is - 18 V. The measured 3 dB bandwidth is 308 MHz, which is limited by the resistance of p-type distributed Bragg reflector mirror. The tunable wavelength in a range of 18 nm with the angle of incident light was observed.

Hydrogen contaminant and its correlation with background electrons in GaN

GaN epilayers grown by molecular beam epitaxy using NH3 as the nitrogen source were found to contain hydrogen. We further notice that the background electron concentration in GaN can be correlated with the amount of hydrogen contaminant. X-ray photoelectron spectroscopy (XPS) measurements of the N Is peak reveal that hydrogen is bound to nitrogen. This will make the corresponding Ga atom see insufficient N counterpart, as can be inferred from the XPS Ga 3d spectrum. We then think that nitrogen in the lattice terminated by hydrogen is an effective nitrogen vacancy and hence a donor accounting for the background electrons.

Isolation and Characterization of a Methomyl-Degrading Paracoccus sp mdw-1

Methomyl, an extremely toxic pesticide, is widely used in agriculture. A strain named mdw-1 capable of degrading methomyl rapidly was successfully isolated from activated sludge in this study. It could utilize methomyl as the sole carbon or nitrogen source. The optimal temperature and medium pH for its growth and methomyl biodegradation were 30 degrees C and 7.0, respectively. It was identified as a Paracoccus sp. according to its morphological features, physiological and biochemical characteristics, and phylogenetic analysis based on the sequence of 16S rDNA. Gas chromatography-mass spectrometry (GC-MS) analysis showed that methomyl could be completely transformed to S-methyl-N-hydroxythioacetamidate in 10 h of incubation with the isolate mdw-1.

3μm GaInNAs/GasAs Quantum Well Resonant Cavity Enhanced Photodetector

A 1.3μm GaInNAs resonant cavity enhanced (RCE) photodetector (PD) has been grown by molecular beam epitaxy (MBE) monolithically on (100) GaAs substrate using a home-made ion-removed dc-plasma cell as nitrogen source. A transfer matrix method was used to optimize the device structure. The absorption region is composed of three GaInNAs quantum wells separated by GaAs layers. Devices were isolated by etching 130μm-diameter mesas and filling polyamide into grooves. The maximal quantum efficiency of the device is about 12% at 1.293μm. Full width at half maximum (FWHM) is 5.8nm and 3dB bandwidth is 304MHz. Dark current is 2 * 10~(-11) A at zero bias voltage. Further improvement of the performance of the RCE PD can be obtained by optimizing of the structure design and MBE growth conditions.

1.3 mu m GaInNAs/GaAs multiple-quantum-wells resonant-cavity-enhanced photodetectors

A GaInNAs/GaAs multiple quantum well (MQW) resonant-cavity enhanced (RCE) photodetector operating at 1.3 mum with the full-width at half-maximum of 5.5 nm was demonstrated. The GaInNAs RCE photodetector was grown by molecular-beam epitaxy using an ion-removed dc-plasma cell as nitrogen source. GaInNAs/GaAs MQW shows a strong exciton peak at room temperature that is very beneficial for applications in long-wavelength absorption devices. For a 100-mum diameter RCE photodetector, the dark current is 20 and 32 pA at biases of 0 and 6 V, respectively, and the breakdown voltage is -18 V. The measured 3-dB bandwidth is 308 MHz. The reasons resulting in the poor high speed property were analyzed. The tunable wavelength of 18 nm with the angle of incident light was observed.

白腐菌选择性降解木质素的研究

对15株白腐真菌进行了以玉米秸秆为基质的初步筛选，从中获得一株选择性系数较高的菌株Y10，并对其降解玉米秸秆的情况进行了研究。结果表明，在30天的培养过程中菌株Y10对玉米秸秆降解的选择性系数都大于1，第15天选择性系数最高为3.88。对未经降解和降解过的玉米秸秆分别作了紫外光谱和红外光谱分析，结果表明，经该菌降解后玉米秸秆的化学成分发生了很大变化，且木质素的降解程度要大于纤维素的降解程度。对菌株Y10进行了ITS-5.8S rDNA序列鉴定，初步判定其为Cerrena sp.。 为了考查不同的外源添加物对菌株Y10降解玉米秸秆的影响，在以玉米秸秆为基质的固态发酵培养基中分别添加了7种金属离子、8种碳源、6种氮源。结果显示，这7种金属离子均能促进木质素的降解，并且一定浓度的某些离子明显抑制纤维素的降解；其中添加0.036%的MnSO4·H2O和0.36%的MgSO4·7H2O对纤维素降解的抑制作用比较强，降解率分别为0.96%和1.31%，木质素的选择性系数分别达到了34.40和20.17。8种碳源中除麦芽糖外都能促进木质素的降解，除微晶纤维素外都明显促进纤维素的降解。6种氮源中酒石酸铵、硫酸铵、草酸铵和氯化铵的添加都会使该菌生长变慢，而且氮源浓度越高菌丝生长越慢。外加碳源和金属离子对半纤维素降解和选择性系数的影响不大。 同时对菌株Y10在液态培养下产木质素降解酶的条件和培养基做了优化。结果表明，在初始产酶培养基中，菌株Y10的漆酶酶活在第10d达到最高，锰过氧化物酶酶活在第11d达到最高，基本上检测不到木质素过氧化物酶。菌株Y10产漆酶的最适温度为32℃，最适PH为6.0；产锰过氧化物酶的最适温度为32℃，最适PH为6.5。菌株Y10产漆酶的最佳碳源为甘露糖，最佳氮源为酒石酸铵，最适诱导剂VA浓度为3 mmol/L，最适表面活性剂TW-80浓度为1%。 利用响应面法对其产漆酶的培养基进行优化，优化后的培养基配方为葡萄糖10.00 g/L，酒石酸铵0.50 g/L，大量元素296.50 ml/L，微量元素100.00 ml/L，NTA 1.40 g/L，VA 5.00 mmol/L，吐温-80加入量为0.10%。进行了菌株Y10产漆酶的验证实验，实测酶活为5282.56 U/L，与预测酶活5162.73 U/L接近。在优化后培养基中，菌株Y10在第14 d达到生长的最高峰，第20 d时，漆酶酶活最高，为11325.00 U/L；第16 d时，锰过氧化物酶酶活最高，为30.77 U/L。 对菌株Y10的漆酶酶学性质做了初步的研究，结果显示，酶反应的最适温度为40℃-65℃，最适PH为3.0。在40℃，PH=3.0时，漆酶催化ABTS反应的米氏方程为 。 Fifteen white-rot fungi based on corn stalk were screened. One white-rot fungus Y10 with high selectivity value was obtained. The degradation of corn stalk was initially studied. The results indicated that the selectivity value was above 1 during the 30 day-cultivation and the highest was 3.88 after 15 days. The composition of untreated and treated stalk was analyzed through ultraviolet spectroscopy and infrared spectroscopy. It was found that the composition of treated stalk was greatly altered and the degree of the degradation of lignin is greater than the cellulose. Y10 was identified as Cerrena sp. by ITS -5.8S rDNA sequence analysis. The influence of metal ions, carbon sources and nitrogen sources on corn stalk degradation by white-rot fungus was studied. While all seven metal ions could promote lignin degradation, the cellulose degradation was best inhibited at certain ion concentrations. Notably, when 0.036% MnSO4·H2O and 0.36% MgSO4·7H2O were added into the medium, the cellulose degradation was restrained to the extents that the coefficients of lignin selectivity rose to 34.40 and 20.17 respectively. It was also found that all carbon sources except maltose can promote lignin degradation. The addition of carbon sources other than microcrystalline cellulose significantly promoted cellulose degradation. The addition of the nitrogen sources, ammonium tartrate, ammonium sulfate, oxalate, ammonium chloride, resulted in remarkable inhibition to mycelium growth; the larger the concentrations of nitrogen sources are, the slower the mycelium grew. The addition of carbon sources and metal ions had less impact on the degradation of hemicellulose and selectivity value. Meanwhile, we optimized the conditions and culture medium of the lignin-degrading enzyme production of strain Y10. The results showed that in the initial culture medium, the Lac activity was highest at the 10th day, the MnP activity was highest at the 11th day and the LiP could not be detected. The optimum condition of Lac was at temperature 32 and PH =6.0 and the optimum condition of MnP was at temperature 32 and PH =6.5. The optimum carbon source for Lac was seminose, the optimum nitrogen source was ammonium tartrate, the optimum content of VA was 3 mmol/L, the optimum content of TW-80 was 1%. PB and RSM were used to optimize the culture medium of laccase by white-rot fungus Y10. The optimum culture medium was consist of glucose 10.00 g/L, ammonium tartrate 0.50 g/L, macro elements 296.50 ml/L, trace elements 100.00 ml/L, NTA 1.40 g/L, VA 5.00 mmol/L, TW-80 0.10%. Under the optimal conditions, the activity of laccase was 5282.56 U/L and the experimental value agreed with the predicted value 5162.73 U/L. The biomass was highest at the 14th day, the Lac activity was highest at the 20th day, the MnP activity was highest at the 16th day. The results of the studies on the characteristics of Lac showed that the optimum temperature for Lac activity is 40℃-65℃ ; the optimum PH for Lac activity is 3.0 and under 40℃，PH=3.0, the Michaelis-menten equation of Lac catalized ABTS oxidation was .

厌氧复合菌系的筛选及含纤维素原料预处理复合菌剂的研究

本文从不同厌氧生境中获得7组(C-2、Y-2、L-2 、NZ、H-3、CZ、L-3)具有纤维素降解能力的复合菌系。经过不断传代、淘汰纤维素降解能力降低的菌系，最后得到一组高效、传代稳定的厌氧纤维素分解复合菌系L-3。该菌系可使滤纸在42 h内溃烂，并能在分解纤维素的同时产氢气。对L-3复合菌系的产酶条件进行了研究，结果表明，在实验范围内该菌系的产酶最适条件为：pH 6.5，温度37 ℃，接种量5 %，最佳碳源为滤纸，最佳氮源为硫酸铵。第10天测得羧甲基纤维素酶(CMCase)、滤纸酶(FPA)、外切葡聚糖酶(C1)、β-葡聚糖苷酶(β-glucodase)的酶活分别为0.216 U/ml、0.101 U/ml、0.132 U/ml、0.002 U/ml，滤纸失重率70.6 %。发酵代谢产物乙醇和丁酸含量分别可达1378 mg/L 、2695 mg/L，发酵产生的气体中氢气含量最高可达70.2 %。DGGE结果表明该菌系主要由14种菌组成，其中有三株菌在发酵前后菌数发生了明显的变化，说明在以滤纸为底物的降解过程中，这三株菌起到了重要作用，对这三株菌进行了分子生物学鉴定，初步定为Clostridium phytofermentans、Clostridium cellulovorans、Desulfovibrio sp。 利用实验室分离得到的纤维素降解菌，最终配制出由10、X-1、X-13、ST-13、L-3组成的好氧-厌氧纤维素降解复合菌剂。以秸秆为发酵底物，菌剂接种量1%，利用复合菌剂预处理后的秸秆，发酵总产气量相对于对照提高了71.62%，甲烷含量最高可达70.08%。 A group of microbial consortia L-3 was isolated from the anaerobic fermentation residue of corn stalk, which could degrade cellulose and produce hydrogen. The CMCase, FPA, C1 and β-glucosidase activity of L-3 could reach to 0.216 U/ml, 0.101 U/ml, 0.132 U/ml and 0.002 U/ml, respectively. In the filter degrading process, the filter paper collapsed in the liquid culture within 42 h and the filter degrading rate could reach to 70.6% in the 13 days, meanwhile, hydrogen was determined and the highest hydrogen content was 70.2%. The optimum cellulase-degrading conditions were filter papaer as the carbon source, (NH4)2SO4 as the nitrogen source, 37 ℃ and pH 6.5 in this experiment. DGGE results showed that the microbial consortia L-3 mainly included 14 strains. The amount of 3 strains were changed during the fermentation. These strains were identified as Clostridium phytofermentans、Clostridium cellulovorans、Desulfovibrio sp by 16S rDNA sequence analysis. The cellulose- degrading microbial agent was composed by 10, X-1, X-13, ST-13, L-3 which were isolated in the laboratory. The straw pretreated by cellulose-degrading microbial agent was used to ferment, the total biogas production increased by 72% comparing to the control. The content of methane could reach to 70.08%。

溶藻菌群对铜绿微囊藻的溶藻效应及其作用机理研究

水华暴发是一个世界性的问题，近年来在发展中国家显得尤其严重。水华暴发给环境和公众健康带来巨大灾难，一些蓝藻产生的毒素可以造成鱼类、鸟禽和家畜的死亡，而臭名昭著的微囊藻产生的微囊藻毒素更是有强烈致癌效应。因此，寻找控制水华藻类的有效方法非常迫切。在利用物理和化学方法处理不甚理想的情况下，利用溶藻细菌控藻成为一个新的研究方向。溶藻细菌一般直接从富营养化水体中分离，杀藻活力对有害蓝藻具有较强的选择性而不危害其它生物，尤其适合在水华发生初期使用，可以在短时间内达到阻止藻类增殖的效果。本研究富集分离到一个高效溶解铜绿微囊藻的溶藻菌群，对其溶藻效应和溶藻机制进行了探索研究。 1溶藻菌群的富集筛选及其溶微囊藻效果 富集筛选得到一个有明显抑藻效果的菌群，它对铜绿微囊藻有显著溶藻效果。与对照组相比，加入富集的溶藻菌后，第4 d开始出现溶藻现象，6~8 d出现明显的溶藻效果，8 d后测得叶绿素去除率在85%以上。 2 溶藻菌群的作用范围及溶藻特性 富集分离到的溶藻菌群对铜绿微囊藻和念珠藻有显著溶藻作用，对水华微囊藻和其它几株受试微囊藻没有明显溶藻效应。该溶藻菌群不仅可以在液体中溶解铜绿微囊藻，生长在固体平板上的藻苔也有一定的溶藻效应，生成溶藻空斑。保证快速溶藻的最大稀释度可以达到1/100, 000。 3 环境因子对菌群溶藻效力的影响 试验发现，不同的pH、温度、和光照条件下，溶藻菌群溶藻效力明显不同，且不同种类的氮源对其溶藻作用也有一定影响。这些条件对该菌群溶藻作用的影响，在相当的程度上可能取决于它们对藻和细菌两者的生长状况的影响综合。 4 溶藻菌群的溶藻作用机理 溶藻菌液过滤除菌和煮沸灭菌处理后溶藻液，未见明显的溶藻效果，只有原液具有很好的溶藻效果。因此可初步确定，蓝藻细胞的溶解可能是由溶藻菌直接接触藻细胞产生的作用效果。显微镜观察发现，细菌在溶藻的过程中频繁地接触藻细胞并侵入藻细胞，破坏进而裂解杀死藻细胞。这也进一步说明了此溶藻菌是通过直接方式杀藻。 5 溶藻菌群的菌群结构解析 分离有溶藻效果的纯菌的多次尝试都没有成功。结合DGGE和16S rDNA文库综合分析发现：Rubritepida菌，假单胞菌和鞘氨醇单胞菌是存在于铜绿微囊藻中的三种伴生细菌。加入富集的溶藻菌群后，菌群结构发生明显的变化，Rubritepida菌、假单胞菌消失，混合菌群则包含未培养黄杆菌，鞘氨醇单胞菌和噬氢菌，其中黄杆菌是优势菌群，并且细菌种群结构的变化与藻细胞消亡之间有显著的相关性。通过菌种的分离鉴定与DGGE和16S rDNA文库的测序结果比较，一些未培养菌可能在溶藻过程中起重要调控作用。 6 溶藻细菌控藻应用基础 (1) 扩大规模的模拟水华实验进一步确定了细菌对微囊藻的强烈溶解作用。 (2) 铜绿微囊藻(Microcystis aeruginosa 905, zc)、微囊藻(Microcystis spp., zd)和溶藻菌群共培养试验表明，zc可以抑制zd生长，而溶藻菌群可以溶zc。 本研究是第一次报道混合菌群的溶藻效应。该溶藻菌群对带有藻际细菌的铜绿微囊藻具有高效的溶藻效力，表明它对自然界中存在的带菌铜绿微囊藻和其它一些蓝藻的生消具有一定的控制作用。对进一步研究菌藻关系与生态学作用，以及对富营养化湖泊和水库水体中蓝藻暴发的防控，该菌群具有一定的应用潜力。 Cyanobacterial blooms break out frequently all over the world, especially in developing countries. Blooms create enormous disasters to public health and to the environment. Some cyanobacterial blooms produce extremely toxic substances that have killed fish, domestic animals and birds. It has been well known that microcystins, a hepatoxin produced by Microcystis, can promote tumors in humans. So it is very important to find an effective method for controlling the growth of the bloom-forming algae. Measures for controlling such kind of algae include physical, chemic and biologic means, but the former two may damage the aquatic environment and require high-energy inputs. The alternative approach for the elimination of nuisance algae involves the application of algicidal bacteria. The algicidal bacteria, which are nontoxic to other organisms and most of which are isolated from the eutrophic lake in situ, may be potential microbial algaecides. In the initial stages of the water blooms, they are able to restrain the biomass or multiplication of the bloom-forming algae in a short time. In order to use algicidal bacteria to suppress blooms of M. aeruginosa, we isolated a bacterial culture capable of lysing the noxious cyanobacteria M. aeruginosa. In this paper we described some properties of the bacterial culture and its growth-inhibiting or algicidal effects on the growth of M. aeruginosa, and investigated its algicidal mechanisms. 1 Enrichment of a microbial culture that lyses Microcystis aeruginosa A mixed bacterial culture was isolated from a hypereutrophic pond and showed significant algicidal activity against the noxious Microcystis aeruginosa. Algae lysis would be seen obviously 4 days later when the algae culture was killed and became yellow contrast to no-addition controls, and chlorophyll a (chl-a) reduction went beyond 85% 8 days later. 2 The host range and some other algicidal feature of the mixed algicidal culture. Microcystis aeruginosa, Nostoc sp., were susceptible to the mixed algicidal culture, while the lytic effects of this mixed culture on Microcystis flos-aquae and some other tested Microcystis were feeble.The algicidal culture can not only lyse M. aeruginosa in liquid media, but aslo lyse M. aeruginosa lawns on soft agar plates and form plaques. The maximun dilution of the mixed culture required for rapid Microcystis lysis is 1/100, 000. 3 Influences of environmental factors such as pH, temperature, illumination, and the nitrogen source on the lytic activity of the mixed bacterial culture on Microcystis aeruginosa. In our investigations, it was shown that the lytic activity of the mixed bacterial culture on Microcystis aeruginosa was straightly correlated with pH, temperature, illumination, as well as the nitrogen source in the medium. The impacts of these environmental factors on the algicidal activity of the mixed bacterial culture, to a certain extent, may depend on both the algal and the bacterial growth rates under the tested environmental conditions. 4 The mechanisms of algal cell lysis by the algicidal bacteria Death was detected when the mixed bacterial culture was added to the algal culture, but not when only the culture filtrate or autoclaved bacterial culture was added. This indicates that the mixed bacterial culture did not release extracellular products inhibitory to Microcystis aeruginosa. In addition, under the microscope, we observed frequent contacts btween bacteria and algae cells, and some bacteria can even penetrate into target algal cells and destroyed them. These results may suggest that the bacterium kill the alga by direct contact. 5 Molecular Characterization of the algicidal bacterial culture Attempts for isolation of pure bacterium or bacteria from the enrichment culture responsible for Microcystis lysis have so far been failed. Based on PCR-DGGE (denaturing gradient gel electrophoresis) and 16S rDNA clone library analysis, Rubritepida sp., Pseudomonas sp. and Sphingomonas sp., as accompanying bacteria, were existed in M. aeruginosa. The bacterial community in M. aeruginosa showed significant change after adding the enrichment culture, where uncultured Flavorbacterium sp., Sphingomonas sp. and Hydrogenophaga sp. were observed, and the uncultured Flavorbacterium sp. became a dominant species. The obvious correlation can be seen between change of bacterial population and extinction of M. aeruginosa. Compared identification of pure bacterium with sequencing of DGGE bands and the clone distribution of the clone libraries, it was inferred that some uncultured bacteria were probably play an important role in controlling the growth and abundance of M. aeruginosa. This report is the first example of a mixed bacterial culture with the ability to lyse M. aeruginosa. 6 Further study for algae control by applications of algicidal bacteria (1) Algae lysis would be seen obviously 6 days later when the algae culture was killed and became yellow contrast to no-addition controls, and chlorophyll a (chl-a) was reducted to a low level 20 days later in the simulated water bloom experiments. (2) The growth of Microcystis sp. (zd) was restrained by Microcystis aeruginosa 905 (zc) when they were co-cultured together, and zc was lysed by the algicidal bacterial culture. This report is the first example of a mixed bacterial culture with the ability to lyse M. aeruginosa, and its algicidal activity remained high against non-axenic tested M. aeruginosa, suggesting that bacteria in the natural environment could play a role in controlling the growth and abundance of M. aeruginosa and other cyanobacteria. Such bacteria could also potentially be used as agents to prevent the mass development of cyanobacteria in eutrophic lakes and reservoirs.