串并联数控机床的作业空间分析

鉴于并联机床普遍存在有效作业空间小、运动控制复杂和实用刚度还不理想等不足．采用了串并联混合式机床运动结构．针对所研究的4—4构型串并联机床,分析了影响作业性能的几何约束条件,采用基于位置逆解模型的极限边界数值搜索法,确定了机床作业空间,并通过数值仿真研究获得了机床运动参数和结构参数对作业空间的影响规律，为优化机床结构尺寸以获得尽可能大的有效作业空间奠定了基础。

并联机床的发展现状与展望

论述并联机床的发展现状及与传统机床的区别。在对国内外典型并联机床样机的工作原理分析的基础上，指出目前并联机床研究中所面临的主要问题，并对并联机床的研究发展方向进行了展望。

Aberration measurement of projection optics in lithographic tools based on two-beam interference theory

The degradation of image quality caused by aberrations of projection optics in lithographic tools is a serious problem in optical lithography. We propose what we believe to be a novel technique for measuring aberrations of projection optics based on two-beam interference theory. By utilizing the partial coherent imaging theory, a novel model that accurately characterizes the relative image displacement of a fine grating pattern to a large pattern induced by aberrations is derived. Both even and odd aberrations are extracted independently from the relative image displacements of the printed patterns by two-beam interference imaging of the zeroth and positive first orders. The simulation results show that by using this technique we can measure the aberrations present in the lithographic tool with higher accuracy. (c) 2006 Optical Society of America.

Aberration measurement of projection optics in lithographic tools by use of an alternating phase-shifting mask

As a critical dimension shrinks, the degradation in image quality caused by wavefront aberrations of projection optics in lithographic tools becomes a serious problem. It is necessary to establish a technique for a fast and accurate in situ aberration measurement. We introduce what we believe to be a novel technique for characterizing the aberrations of projection optics by using an alternating phase-shifting mask. The even aberrations, such as spherical aberration and astigmatism, and the odd aberrations, such as coma, are extracted from focus shifts and image displacements of the phase-shifted pattern, respectively. The focus shifts and the image displacements are measured by a transmission image sensor. The simulation results show that, compared with the accuracy of the previous straightforward measurement technique, the accuracy of the coma measurement increases by more than 30% and the accuracy of the spherical-aberration measurement increases by approximately 20%. (c) 2006 Optical Society of America.

Measurement technique for in situ characterizing aberrations of projection optics in lithographic tools

As the feature size decreases, degradation of image quality caused by wavefront aberrations of projection optics in lithographic tools has become a serious problem in the low-k1 process. We propose a novel measurement technique for in situ characterizing aberrations of projection optics in lithographic tools. Considering the impact of the partial coherence illumination, we introduce a novel algorithm that accurately describes the pattern displacement and focus shift induced by aberrations. Employing the algorithm, the measurement condition is extended from three-beam interference to two-, three-, and hybrid-beam interferences. The experiments are performed to measure the aberrations of projection optics in an ArF scanner. (C) 2006 Optical Society of America.

Coma measurement of projection optics in lithographic tools based on relative image displacements at multiple illumination settings

In this paper, we propose a novel method for measuring the coma aberrations of lithographic projection optics based on relative image displacements at multiple illumination settings. The measurement accuracy of coma can be improved because the phase-shifting gratings are more sensitive to the aberrations than the binary gratings used in the TAMIS technique, and the impact of distortion on displacements of aerial image can be eliminated when the relative image displacements are measured. The PROLITH simulation results show that, the measurement accuracy of coma increases by more than 25% under conventional illumination, and the measurement accuracy of primary coma increases by more than 20% under annular illumination, compared with the TAMIS technique. (c) 2007 Optical Society of America.

Optical properties of semiconductor quantum-well material using photonic crystal fabricated by micro-fabrication machine

Two-dimensional photonic crystals in near infrared region were fabricated by using the focused ion beam ( FIB) method and the method of electron-beam lithography (EBL) combined with dry etching. Both methods can fabricate perfect crystals, the method of FIB is simple,the other is more complicated. It is shown that the material with the photonic crystal fabricated by FIB has no fluorescence,on the other hand, the small-lattice photonic crystal made by EBL combined with dry etching can enhance the extraction efficiency two folds, though the photonic crystal has some disorder. The mechanisms of the enhanced-emission and the absence of emission are also discussed.

An algorithm of analysis tools on points distribution in high dimension space: The distance of a point and an infinite sub-space

This paper discusses the algorithm on the distance from a point and an infinite sub-space in high dimensional space With the development of Information Geometry([1]), the analysis tools of points distribution in high dimension space, as a measure of calculability, draw more attention of experts of pattern recognition. By the assistance of these tools, Geometrical properties of sets of samples in high-dimensional structures are studied, under guidance of the established properties and theorems in high-dimensional geometry.

A Structured Prediction Approach for Statistical Machine Translation

We propose a new formally syntax-based method for statistical machine translation. Transductions between parsing trees are transformed into a problem of sequence tagging, which is then tackled by a search- based structured prediction method. This allows us to automatically acquire transla- tion knowledge from a parallel corpus without the need of complex linguistic parsing. This method can achieve compa- rable results with phrase-based method (like Pharaoh), however, only about ten percent number of translation table is used. Experiments show that the structured pre- diction approach for SMT is promising for its strong ability at combining words.

Wear mechanism map of uncoated HSS tools during drilling die-cast magnesium alloy

A wear mechanism map of uncoated high-speed steel (HSS) tools was constructed under the conditions of dry-drilling die-cast magnesium alloys. Three wear mechanisms appear in the map based on the microanalysis of drilled HSS tools by SEM, including adhesive wear, abrasive wear and diffusion wear. In the map, there exists a minor wear region which is called "safety zone". This wear mechanism map will be a good reference for choosing suitable drilling parameters when drilling die-cast magnesium alloys.

基于Arc Hydro Tools的流域特征自动提取——以贵州省内乌江流域为例

简要回顾和讨论了基于栅格数字高程模型(DEM)自动提取流域特征的原理和方法，介绍了一个新的基于ArcGIS开发的提取流域特征的工具Arc Hydro Tools，基于Arc Hydro Tools 提取流域特征包括5 个流程：DEM 的预处理、水流流向的确定、汇流栅格图的生成、河网的自动生成、子流域边界的划分。最后以贵州省内乌江流域为研究区进行了试验，试验结果表明：提取结果的精度在总体上是符合要求的，但在地势平坦区或人类活动干扰较大的地区，提取的结果与实际相差较大。从提取的效率和试验结果的精度两方面来看，基于Arc Hydro Tools 的流域特征自动提取是切实可行的。