Propulsion characteristics of wing-in-ground effect dual-foil propulsors

Propulsion characteristics of wing-in-ground effect propulsors were investigated using a comparative analysis of thrust and powering characteristics between wing-in-ground (WIG) effect thrusters and traditional screw propellers. WIG thrusters were found to have constant thrust production and efficiency, nearly independent of speed of advance, as contrary to screw propellers, whose optimum efficiency occurs at only one speed point. To produce the same amount of thrust as equivalent screw propellers, WIG thrusters have to work under heavily loaded operating conditions. WIG thrusters were also found to produce a relatively lower but nearly constant efficiency and thrust, independent of speed. Another distinguishing propulsion characteristic revealed for WIG thrusters is that they are capable of operating at much higher speeds, in a range of three to six times that of screw propellers of the same size. While the speed range of screw propellers is mainly limited by their geometric pitch, the speed range of WIG thrusters has no speed limit in ideal fluid. In reality, the speed range is only limited by viscous drag and cavitation, or compressibility, in water or air, respectively. This suggests a potential for WIG thrusters of higher speed application than screw propellers. An experimental investigation and validation of the propulsion system is warranted. Crown Copyright (C) 2010 Published by Elsevier Ltd. All rights reserved.

Photoionization of 1s electron and corresponding shake-up process in ground and excited lithium atoms

The cross sections of the 18 electron photoionization and corresponding shake-up processes for Li atoms in the ground state 1s(2)2s and excited states 1s(2)2p, 1s(2)3p, 1s(2)3p and 1s(2)3d are calculated using the multi-configuration Dirac-Fock method. The latest experimental photoelectron spectrum at hv = 100 eV [Cubaynes D et al. Phys. Rev. Lett. 99 (2007) 213004] has been reproduced by the present theoretical investigation excellently. The relative intensity of the shake-up satellites shows that the effects of correlation and relaxation become more important for the higher excited states of the lithium atom, which are explained very well by the spatial overlap of the initial and final state wavefunctions. In addition, strong dependence of the cross section on the atomic orbitals of the valence electrons are found, especially near the threshold.

Improvement of stoichiometry in semi-insulating gallium arsenide grown under microgravity

A semi-insulating (SI) GaAs single crystal was recently grown in a retrievable satellite. The average etch pit density (EPD) of dislocations in the crystal revealed by molten KOH is 2.0 x 10(4) cm(-2), and the highest EPD is 3.1 x 10(4) cm(-2) This result indicates a quite good homogenity of the EPD which is much better than the ground-grown crystals. A similar better homogenity of the stoichiometry i.e., the [As]/([As] + [Ga]) ratio has been found in the space-grown SI-GaAs single crystal studied nondestructively using a new mapping method based upon X-ray Bond diffraction. The average stoichiometry in the space-grown crystal is 0.50007 with mean-square deviation of 6x10(-6), while the average stoichiometry in ground-grown SI-GaAs crystal is more than 0.50010. (C) 1998 Elsevier Science B.V. All rights reserved.

Experimental Study of Surface Deformation and Flow Pattern on Buoyant-Thermocapillary Convection

Free surface deformation is one of the most important physical phenomena in fluids with free surface. In the present paper, convection and surface deformation caused by thermocapillary effect in a rectangular cavity were investigated. In ground experiments, the convection was also affected by gravity. The cavity has a horizontal cross section of 52mm×42mm and the thikkness of the liquid layer is 4mm. Temperature difference between two sides of the liquid layer was increased gradually, and the flow in liquid layer will develop from steady to unstable convection. An optical diagnostic system consisting of a revised Michelson interferometer with image processor was developed to study fluid surface deformation in convection, and the displacements of free surface oscillation were determined. PIV technique was adopted to observe the evolution of flow pattern, and the velocity fields were obtained quantitatively. The present experiments demonstrate that surface deformation is quite distinct in buoyant-thermocapillary convection. in order to understand the mechanism of buoyant-thermocapillary convection, not only the hydrothermal wave instability but also the surface wave instability should be discussed.

Wavelet denoising and feature extraction of seismic signal for footstep detection

Seismic sensors are widely used to detect moving target in ground sensor networks. Footstep detection is very important for security surveillance and other applications. Because of non-stationary characteristic of seismic signal and complex environment conditions, footstep detection is a very challenging problem. A novel wavelet denoising method based on singular value decomposition is used to solve these problems. The signal-to-noise ratio (SNR) of raw footstep signal is greatly improved using this strategy. The feature extraction method is also discussed after denosing procedure. Comparing, with kurtosis statistic feature, the wavelet energy feature is more promising for seismic footstep detection, especially in a long distance surveillance.

川西亚高山云杉人工林天然更新与生境异质性研究

川西亚高山针叶林是四川森林的主体，是长江上游重要的生态屏障。云杉作为亚高山针叶林人工更新的主要树种，已经在该地区形成了大面积的人工纯林。目前，许多云杉人工林分已经进入更新成熟龄，而这些人工林的持续更新却成为日益凸现的问题。探讨这些云杉人工林的自我更新潜力及云杉种子种群更新特点，可为培育后续森林资源提供科学依据。 本文以川西米亚罗亚高山60a云杉人工林为研究对象，并以该区域内相对稳定的植被群落——天然林为对照，采用种子收集器、土壤种子库筛选、室内外种子萌发实验及野外幼苗调查等方法，从异质性微生境的角度研究了种子雨下落之后，不同微生境对种子库、种子萌发、幼苗建立及分布这一前期更新过程的影响，得出如下结果： 1、通过对川西亚高山60a云杉人工林和天然林6年内种子雨雨量、形态特征、散步动态等的持续观测和综合比较可以发现，云杉林结实特点由于林木自身的特征存在着巨大的变动，2002年和2006年两个种子结实大年内，60a人工林种子雨强度分别达到1088.2 ± 52.3粒/m2和704.3 ± 48.9粒/m2，远大于天然林579.9 ± 28.9粒/m2 和507.5± 30.7粒/m2；且云杉林结实质量优于天然林。60a人工林结实量大，种子质量也最好，相对天然林来说对种群的天然更新以及群落的演替都有最大的贡献潜力。应该说，在川西亚高山云杉人工林的天然更新过程中，种源不是影响天然更新的因素。在种子结实大年里，达到更新成熟的云杉人工林有着优于该地区相对稳定植被群落——天然林的种源优势。至少在种子结实大年，种子供应不是该区域人工林天然更新的限制因子。 2、相对于天然林种子库，人工林种子库在种子萌发前能够有较多的有活力种子。虽然这其中有种子雨输入量有差别的因素存在，但两种林分种子库对种子的保存率的不同才是造成这种差异的主要因素。在人工林中，不同地被类型形成的微生境显著地影响了种子库中种子的密度、垂直分布。有地被物存在的微生境能够将种子雨的大部分截留在地被层中，成为幼苗出现的主要场所；同时不同的地被物对种子的保存情况存在显著的差异，苔藓和凋落物层能都较好地保持其中的种子，到种子萌发前，这两种种子库类型能分别为天然更新提供366.1粒/m2和302粒/m2的有效种子。从这点来看，林下地被物上的种子库能够为天然更新萌发阶段提供数量可观的物质基础。 3、种子的萌发和幼苗的定居是天然更新过程中种子库向幼苗库转化的关键环节。总的说来，米亚罗人工林区60a云杉人工林种子向幼苗的转化率十分低下，凋落物、苔藓、草本、裸地四种主要地被物以及天然林内种子/幼苗的转化率分别仅为2.22%、2.14%、0.57%、0.67%、1.05%。这种低的转化率成为云杉林天然更新的限制性因子。但在现有更新条件下，微生境对这一环节仍然显示出十分显著的影响，表现为凋落物和苔藓对现有更新的新幼苗的保存率高于其它类型及天然林。苔藓和凋落物在种子萌发，幼苗保存，以及幼苗分布上都要优于其它地被物类型；另外，微地形对天然更新过程的影响也很显著，凹立地上更适宜于种子的汇集、萌发和定居。 Subalpine coniferous forests dominate most parts of the forested areas in western Sichuan, and they are important ecological barriers in the upper reaches of the Yangtze River. Picea asperata is one of the keystone spruce species for re-afforestation after felling of the natural forests and there have been a total of ca. 13 000 ha of plantations dominate by this species established. Nowadays, many P. asperata plantations have reached reproductive maturity. However, continued regeneration becomes to an important problem in these plantations. Understanding their self-regeneration potential and the regeneration characteristics of seed populations in spruce plantations of these plantations can have some insights on the management of these plantations and the establishment of following forest resources. A subalpine 60a P. asperata plantation distributed in Miyaluo artificial forest area was studied in this paper, at the same time. Synchronously, a 150a natural spruce forest was studied as comparison. Using seed collecting traps, sieving method for soil seed bank, seed germination experiments and seedling investigations in the field, the effects of heterogeneous microsites on early natural regeneration processes after seed rain were studied, which included seed banks, seed germination, seedling establishment and distribution. The main results are as follows. 1. Through a 6-year long term investigation of seed rain intensities, characteristic, dispersal dynamics of 60a P. asperata plantation, we could concluded that the seed setting properties of 60a P. asperata plantation have a great variation for the characteristics trees. In the mast seed year of 2002 and 2006, the seed rain intensities of plantation was 1088.2 ± 52.3 seeds/m2 and 704.3 ± 48.9 seeds/m2 respectively, which were much greater than that of natural spruce forest (579.9 ± 28.9 seeds/m2 in 2002, and 507.5± 30.7 seeds/m2 in 2006). Furthermore, the quality of seed rain in P. asperata plantation was better than that of natural spruce forest. Contrasting with natural spruce forest, 60a P. asperata plantation has a greater potential on natural regeneration of P. asperata population and succession of community for the reason of greater seed rain intensities and better seed quality. We can confirm that seed source was not a limiting factor which influences the natural regeneration progress of P. asperata population distributed in subalpine mountain zone, at least in the mast seed year. 2. Contrasting with natural spruce forest, P. asperata population had more viable seeds in seed bank before the germination. Although the difference of seed rain intensities of two forests has effect on this phenomenon, the difference of seed conservation ability in two forests was the main factor. In the P. asperata plantation, the seed densities and seed vertical distribution pattern were significant effected by the microsites, which posed by different ground cover types. In other word, Microsite with ground covers can obstruct most seeds and keep them in ground cover layer from seed rain, and these ground covers would be the main site for seed occurrence. There was a significant difference about seeds conservation ability among these ground covers. Litter and moss could better conserve P. asperata seeds which distributed in this two covers. Seed banks exist in litter and moss ground cover types could respectively provide 302seed/m2 and 366.1seed/m2 for natural regeneration before the seed germination. From this point of view, we could conclude that ground covers can ensure considerable numbers of seeds for the germination process. 3. Seed germination and seed establishment are key steps that the seeds invert to seedlings in natural generation process. In sum, the seed/seeding transform rate in 60a P. asperata plantation distributed in Miyaluo artificial forest area is very low. the seed/seeding transform rates in litter, moss, herb, soil surface and natural spruce forest were 2.22%、2.14%、0.57%、0.67%、1.05%, respectively. The low transform rate become to a limiting factor of P. asperata natural regeneration process. However, under the existing conditions of natural regeneration, microsit still had significant effect on this transform. The states of Seed germination, new seedling conservation, and older seedling distribution in litter and moss were better than in any other ground cover type or natural spruce forest. In addition, the micro-relief has significant effect on natural regeneration process. Concave site was more suitable for seed collection, seed germination and seedling distribution.

急倾斜金属矿体开采岩体移动规律与变形趋势预测研究

Rockmass movement due to mining steep metallic ore body is a considerable question in the surface movement and deformation issue caused by underground mining. Research on coal mining induced rockmass movement and its prediction problem have been performed for a long-term, and have achieved great progress at home and abroad. However, the rockmass movement caused by mining steep metal mine is distinctivly different from coal seam mining.. Existing surface movement laws and deformation prediction methods are not applicable to the rockmass movement caused by mining steep metal mine. So far the home and abroad research to this theory is presently at an early stage, and there isn’t mature theory or practical prediction method, which made a great impact on production. In this paper, the research object—Jinchuan nickel mine, which is typical steep metal mine, characterized by complex geological conditions, developed faults, cracked rockmass, high geostress, and prominent engineering stability problems. In addition, backfill mining method is used in the mine, the features of rockmass movement caused by this mining method are also different from other mining methods. In this paper, the laws of rock mass movement, deformation and destroy mechanism, and its prediction were analyzed based on the collection of data, detailed in-sit engineering geology survey, ground movement monitoring by GPS, theoretical analysis and numerical simulation. According to the GPS monitoring of ground surface movement, ground subsidence basin with apparent asymmetry is developing, the influence scope is larger in the upper faulted block than in the lower faulted block, and the center of ground movement is moving along the upper faulted block direction with increasing depth of mining. During the past half and seven years, the largest settlement has amounted to 1287.5mm, and corresponding horizontal displacement has amounted to 664.6mm. On the ground surface, two fissure belts show a fast-growing trend of closure. To sum up, mining steep metal mine with backfill method also exist the same serious problem of rockmass movement hazards. Fault, as a low intensity zone in rockmass, when it located within the region of mining influence, the change of potential energy mainly consumed in fault deformation associated with rockmass structure surface friction, which is the essence of displacement and stress barrier effects characterized by fault rupture zone. when steep fault located in the tensile deformation region incurred by underground excavation, no matter excavation in hangingwall or in footwall of the fault, there will be additional tensile stress on the vertical fault plane and decrease in the shear strength, and always showing characteristics of normal fault slip, which is the main reason of fault escarpment appeared on the ground surface. The No.14 shaft deformation and failure is triggered by fault activation, which showed with sidewall move, rupture, and break down features as the main form of a concentrated expression of fault effects. The size and orientation of principal stress in surrounding rock changed regularly with mining; therefore, roadway deformation and damage at different stages have different characteristics and distribution models. During the process of mining, low-intensity weak structures surface always showed the most obvious reaction, accompany with surface normal stress decrease and shear strength bring down, to some extent, occurred with relative slide and deformation. Meanwhile, the impact of mining is a relatively long process, making the structure surface effect of roadway deformation and damage more prominent than others under the influence of mining. Roadway surrounding rockmass deformation caused by the change of strain energy density field after excavation mainly belongs to elastic deformation, and the correspondented damage mainly belongs to brittle rupture, in this circumstance, surrounding rockmass will not appear large deformation. The large deformation of surrounding rockmass can only be the deformation associated with structure surface friction or the plastic deformation of itself, which mainly caused by the permanent self-weigh volume force，and long-term effect of mining led to the durability of this deformation Good pitting fill effect and supporting effect of backfill, as well as the friction of rockmass structure surface lead to obvious macro-rockmass movement with long-lag characteristics. In addition, the loss of original intensity and new structure surface arisen increased flexibility in rockmass and fill deformation in structure surface, which made the time required for rockmass potential energy translate into deformation work associated with plastic deformation and structure surface friction consumed much, and to a large extent, eliminated the time needed to do those plastic work during repeated mining, all of which are the fundamental reason of rockmass movement aftereffect more significant than before. Mining steep deposits in high tectonic stress area and in gravity stress area have different movement laws and deformation mechanism. The steep deposit, when the vertical size of the mining areas is smaller than the horizontal size of the orebody, no matter mining in gravity stress area or in high tectonic stress area, they have similar features of ground movement with mining horizontal orebody; contrarily, there will appear double settlement centers on the ground surface under the condition of mining in high tectonic stress area, while there will always be a single center under the other condition. Meanwhile the ground movement lever, scale of mining influence area and macro features of ground movement, deformation and fracture are also different from mining in gravity stress area, and the fundamental reason lies in the impact of orientation of the maximum principal stress on rock movement features in in-site rock stress field. When mining thick and steep deposit, the ground surface movement and deformation characteristic curves are significantly different from excavating the horizontal ore bed and thin steep deposit. According to the features of rockmass movement rate, the development process of mining-induced rockmass movement is divided into three stages: raising stage, steadily stage and gradually decay stage. Considering the actual exploitation situation, GPS monitoring results and macro-characteristics of surface movement, the current subsidence pattern of Jinchuan No.2 mine is in the early stage of development. Based on analysis of surface movement rate, surface subsidence rate increase rapidly when mining in double lever at the same time, and reach its peak until the exploitation model ended. When double lever mining translate into single, production decreased, surface subsidence rate suddenly start to reduce and maintain a relatively low value, and the largest subsidence center will slowly move along with the hangingwall ore body direction with increasing depth of mining, at the same time, the scope and extent of subsidence in footwall ore body will begin magnify, and a sub-settlement center will appear on ground surface, accompanied with the development and closure trend of ground fissure, the surrounding rockmass of shaft and roadway will be confronted to more frequent and severe deformation and failure, and which will have a negative impact on the overall stability of No.2 mine mining. On the premise of continuity of rockmass movement, gray system model can be used in ground rockmass movement prediction for good results. Under the condition of backfill mining step by step, the loose effect of compact status of the hard, broken rockmass led to lower energy release rate, although surrounding rockmass has high elastic energy, loose and damage occurred in the horizontal ore body, which made the mining process safety without any large geological hazards. During the period of mining the horizontal ore body to end, in view of its special “residual support role”, there will be no large scale rockmass movement hazards. Since ground surface movement mainly related to the intensity of mining speed and backfill effect, on the premise of constant mining speed, during the period of mining the horizontal ore body to end, the rate of ground surface rockmass movement and deformation won’t have sudden change.

Hardware development and ground-based studies for drop shaft experiment on oscillatory convection in half floating-zone

Coordinated measurement of temperature, velocity and free surface oscillation were obtained by using the drop shaft facility for microgravity experiments of half floating zone convection. The ground-based studies gave transition from steady to oscillatory convection for multi-quantities measurement.

Energy spectrum of ground state and excitation spectrum of quasi-particle for hard-core boson in optical lattices

We investigate the energy spectrum of ground state and quasi-particle excitation spectrum of hard-core bosons, which behave very much like spinless noninteracting fermions, in optical lattices by means of the perturbation expansion and Bogoliubov approach. The results show that the energy spectrum has a single band structure, and the energy is lower near zero momentum; the excitation spectrum gives corresponding energy gap, and the system is in Mott-insulating state at Tonks limit. The analytic result of energy spectrum is in good agreement with that calculated in terms of Green's function at strong correlation limit.

Diversity Variation of Ground-dwelling Beetle(Insecta:Coleoptera) Communities in Jiaozi Mountain, Yunnan, China

对云南轿子雪山自然保护区地表甲虫物的种组成及生物多样性季节变化进行了连续跟踪调查.调查结果如下:(1)通过对4种典型微环境样地(草地、灌丛、林地以及农田生态系统)连续3次跟踪连续调查,共获得标本2451头,分别隶属于24科.其中步甲科(Carabidae)为优势类群,占总数的62.10%;隐翅虫科(Staphylinidae)其次,占12.77%.可能由于海拔、气温等因素影响,该地区昆虫活动高峰期较短.(2)通过对4种典型微生态环境中地表甲虫的生物多样性的比较,表明不同生境内甲虫的多样性指数存在动态变化,在不同生境片区内甲虫存在迁移活动,甲虫多在灌丛中越冬,并随季节及食物源迁移.

Species identification of Chinese sturgeon using acoustic descriptors and ascertaining their spatial distribution in the spawning ground of Gezhouba Dam

This study has developed an improved subjective approach of classification in conjunction with Step wise DFA analysis to discriminate Chinese sturgeon signals from other targets. The results showed that all together 25 Chinese sturgeon echo-signals were detected in the spawning ground of Gezhouba Dam during the last 3 years, and the identification accuracy reached 90.9%. In Stepwise DFA, 24 out of 67 variables were applied in discrimination and identification. PCA combined with DFA was then used to ensure the significance of the 24 variables and detailed the identification pattern. The results indicated that we can discriminate Chinese sturgeon from other fish species and noise using certain descriptors such as the behaviour variables, echo characteristics and acoustic cross-section characteristics. However, identification of Chinese sturgeon from sediments is more difficult and needs a total of 24 variables. This is due to the limited knowledge about the acoustic-scattering properties of the substrate regions. Based on identified Chinese sturgeon individuals, 18 individuals were distributed in the region between the site of Gezhouba Dam and Miaozui reach, with a surface area of about 3.4 km(2). Seven individuals were distributed in the region between Miaozui and Yanshouba reach, with a surface area of about 13 km(2).

Electron ground state energy level determination of ZnSe self-organized quantum dots embedded in ZnS

Optical and electrical characterization of the ZnS self-organized quantum dots (QDs) embedded in ZnS by molecular beam epitaxy have been investigated using photoluminescence (PL), capacitance-voltage (C-V), and deep level transient Fourier spectroscopy (DLTFS) techniques. The temperature dependence of the free exciton emission was employed to clarify the mechanism of the PL thermal quenching processes in the ZnSe QDs. The PL experimental data are well explained by a two-step quenching process. The C-V and DLTFS techniques were used to obtain the quantitative information on the electron thermal emission from the ZnSe QDs. The correlation between the measured electron emission from the ZnSe QDs in the DLTFS and the observed electron accumulation in the C-V measurements was clearly demonstrated. The emission energy for the ground state of the ZnSe QDs was determined to be at about 120 meV below the conduction band edge of the ZnS barrier, which is in good agreement with the thermal activation energy, 130 meV, obtained by fitting the thermal quenching process of the free exciton PL peak. (C) 2003 American Institute of Physics.

Ground target detection, classification and sensor fusion in distributed fiber seismic sensor network - art. no. 683015

This paper describes the ground target detection, classification and sensor fusion problems in distributed fiber seismic sensor network. Compared with conventional piezoelectric seismic sensor used in UGS, fiber optic sensor has advantages of high sensitivity and resistance to electromagnetic disturbance. We have developed a fiber seismic sensor network for target detection and classification. However, ground target recognition based on seismic sensor is a very challenging problem because of the non-stationary characteristic of seismic signal and complicated real life application environment. To solve these difficulties, we study robust feature extraction and classification algorithms adapted to fiber sensor network. An united multi-feature (UMF) method is used. An adaptive threshold detection algorithm is proposed to minimize the false alarm rate. Three kinds of targets comprise personnel, wheeled vehicle and tracked vehicle are concerned in the system. The classification simulation result shows that the SVM classifier outperforms the GMM and BPNN. The sensor fusion method based on D-S evidence theory is discussed to fully utilize information of fiber sensor array and improve overall performance of the system. A field experiment is organized to test the performance of fiber sensor network and gather real signal of targets for classification testing.