Experimental Studies of the Material Properties of the Forewing of Cicada (Homoptera, Cicadidae)

Detailed investigations on the structural and mechanical properties of the forewing of the cicada were carried out. Measurement of the structures of the wings showed that the thickness of the membrane of each cell and the diameter of each vein were non-uniform in both the longitudinal and transverse directions, and their means were approximately 12.2 and 133.3 mum, respectively. However, the aspect ratios of the wings and the bodies were quite uniform and were approximately equal to 2.98 and 2.13, respectively. Based on the measured thickness, mass and area of the membranes of the cells, the mean density and the mean area density of the wing were approximately 2.3 g cm(-3) and 2.8 x 10(-3) g cm(-2), respectively. In addition, the diameters of the veins of the wings, including the diameters of the holes in the vein of the leading edge, were examined. The mechanical properties of the wing were investigated separately by nanoindentation and tensile testing. The results indicated that the mean Young's modulus, hardness and yield stress of the membranes of the wings were approximately 3.7 Gpa, 0.2 Gpa and 29 Mpa, respectively, and the mean Young's modulus and strength of the veins along the direction of the venation of wings were approximately 1.9 Gpa and 52 Mpa, respectively. Finally, the relevant results were briefly analyzed and discussed, providing a guideline to the biomimetic design of the aerofoil materials of micro air vehicles.

Validity ranges of interfacial wave theories in a two-layer fluid system

In the present paper, we endeavor to accomplish a diagram, which demarcates the validity ranges for interfacial wave theories in a two-layer system, to meet the needs of design in ocean engineering. On the basis of the available solutions of periodic and solitary waves, we propose a guideline as principle to identify the validity regions of the interfacial wave theories in terms of wave period T, wave height H, upper layer thickness d(1), and lower layer thickness d(2), instead of only one parameter-water depth d as in the water surface wave circumstance. The diagram proposed here happens to be Le Mehautes plot for free surface waves if water depth ratio r = d(1)/d(2) approaches to infinity and the upper layer water density rho(1) to zero. On the contrary, the diagram for water surface waves can be used for two-layer interfacial waves if gravity acceleration g in it is replaced by the reduced gravity defined in this study under the condition of sigma = (rho(2) - rho(1))/rho(2) -> 1.0 and r > 1.0. In the end, several figures of the validity ranges for various interfacial wave theories in the two-layer fluid are given and compared with the results for surface waves.

Modal analysis of deep-etched low-contrast two-port beam splitter grating

Modal analysis of a deep-etched low-contrast two-port beam splitter grating under Littrow Mounting is presented. The guideline for the design of a subwavelength transmission fused-silica phase grating as high-efficiency grating, polarizing beam splitter (PBS), and two-port beam splitter, is summarized. As an example, a polarization-independent two-port beam splitter grating is designed at wavelength of 1064 nm. We firstly analyzed the physical essence of the grating by the simplified modal method. The guideline for the grating design and the approximate grating parameters are obtained. Then using the rigorous coupled-wave analysis (RCWA) with parameters varying around the approximate ones, Optimum grating parameters can be determined. With the design guideline, the time for the rigorous calculation of the grating profile parameters can be reduced significantly. (C) 2008 Elsevier B.V. All rights reserved

LOCAL BENDING OF THIN FILM ON VISCOUS LAYER

Effects of deposition layer position and number/density on local bending of a thin film are systematically investigated. Because the deposition layer interacts with the thin film at the interface and there is an offset between the thin film neutral surface and the interface, the deposition layer generates not only axial stress but also bending moment. The bending moment induces an instant out-of-plane deflection of the thin film, which may or may not cause the so-called local bending. The deposition layer is modeled as a local stressor, whose location and density are demonstrated to be vital to the occurrence of local bending. The thin film rests on a viscous layer, which is governed by the Navier-Stokes equation and behaves like an elastic foundation to exert transverse forces on the thin film. The unknown feature of the axial constraint force makes the governing equation highly nonlinear even for the small deflection case. The constraint force and film transverse deflection are solved iteratively through the governing equation and the displacement constraint equation of immovable edges. This research shows that in some special cases, the deposition density increase does not necessarily reduce the local bending. By comparing the thin film deflections of different deposition numbers and positions, we also present the guideline of strengthening or suppressing the local bending.

Evaluation of the Uncertainties Caused by the Forward Scattering in Turbidity Measurement of the Coagulation Rate

The forward scattering light (FSL) received by the detector can cause uncertainties in turbidity measurement of the coagulation rate of colloidal dispersion, and this effect becomes more significant for large particles. In this study, the effect of FSL is investigated on the basis of calculations using the T-matrix method, an exact technique for the computation of nonspherical scattering. The theoretical formulation and relevant numerical implementation for predicting the contribution of FSL in the turbidity measurement is presented. To quantitatively estimate the degree of the influence of FSL, an influence ratio comparing the contribution of FSL to the pure transmitted light in the turbidity measurement is introduced. The influence ratios evaluated under various parametric conditions and the relevant analyses provide a guideline for properly choosing particle size, measuring wavelength to minimize the effect of FSL in turbidity measurement of coagulation rate.

水库集水区水土保持与流域产水量——以密云水库上游潮白河流域为例

针对密云水库上游承德"21世纪水资源可持续利用项目"中水土流失治理后来水减少,加剧下游城市(北京)水资源供需矛盾的问题,探讨集水区减少水土保持用水,增加流域产水量,从而水资源在下游(首都圈)发挥最大效益的思路。在将流域分成3种类型区的基础上,提出了流域分区治理方案及其标准:1)生态产水功能区,以增加产水供给下游为主要目的,提出以需水量最低的低覆盖度草地配置为主的水土流失坡面治理模式和减少蓄水、增大拦沙的弱化与强化相结合的沟道治理模式;2)生产生活功能区,以满足流域基本粮食生产为主要目的,提出以黄土丘陵区坝地为主的水土流失治理模式及其标准;3)生态产水与生产生活复合功能区,兼顾二者功能,提出以需水量中等的灌木林和疏林配置为主的水土流失治理模式及标准。

Photochromic inorganic-organic multilayer films based on polyoxometalates and poly(ethylenimine)

Novel photochromic inorganic-organic multilayers composed of polyoxometalates and poly(ethylenimine) have been prepared by the layer-by-layer (LbL) self-assembly method. The growth process, composition, surface topography, and photochromic properties of the multilayer films were investigated by UV-visible and Fourier transform infrared spectroscopy, atomic force microscopy, electrospin resonance (ESR), and X-ray photoelectron spectroscopy (XPS). Irradiated with ultraviolet light, the transparent films changed from colorless to blue. Moreover, the blue films showed good reversibility of photochromism, and could recover the colorless state gradually in air, where oxygen plays an important role in the bleaching process. On account of the ESR and XPS results, parts of W6+ in multilayers were reduced to W5+, which exhibited a characteristic blue; a possible photochromic mechanism can be speculated. This work provides basic guideline for the assembly of multilayers with photochromic properties.

子洲—清涧地区上古生界储层综合研究

The exploration and study in recent years shows that the upper Paleozoic in the east of Ordos Basin possesses major exploration potential, so it is necessary to have a comprehensive and synthetic research in this area. Following the guideline of T.A. Cross’s high resolution sequences stratigraphy and combined with sedimentology, the strata and sequence in the research area are divided and correlated. This paper emphasizes on the reservoir in this area and its major fruits are: Firstly, form the framework of the high sequence stratigraphy through mainly studying on the data of core, well drilling and field section combining. Then, think that the best reservoir formation mainly appears in the middle or lower part of long arising semi-cycle, and focus on A type and C1 middle sequence cycle that contributes to the development of formation. Next, think the sedimentary source mainly comes from the epimetamorphic crystalline basement in the north of the Ordoes Basin through analyzing depositional background, researching on sandstone petrography, distribution characteristics of the sedimentary system as well as researching on heavy mineral combination characteristics. Fourthly, give priority to Zizhou-Qingjian area for the first time and gain seven lithofacies paleography maps in the No.2 member of Shanxi and the No.8 member of Shihezi through using the method of isochronal lithofacies paleogeography mapping, then bring forth that Sh2 is mainly developed a type I sequence under the margin of ramp lake-basin background. Fifthly, through researching on the characteristics of reservoir petrography and diagenesis, think that all researched areas experienced compaction and cementation, and there is different types of rocks, only little of the primary pores that are made up of litharenite and lithoclastic quartz sandstone is left, while in lithoclastic quartz sandstone, there are still many primary pores Sixthly, through studying on pore types, microstructure, as well as physical property on the key formation, think that the researched area mostly appears typical low pore, low porosity and permeability, which mainly result from sedimentary and diagenesis. Lastly, through researching on classified evaluation in the key formation, productivity analysis, and combing with reservoir distribution, the researched area is divided into three parts, and think that exploration should be emphasized on formation I and II. The characteristics of sandstones distribution in Sh23 member, gas formation distribution and open flow capacity of exploitation well are all consistent properly with the results of reservoir comprehensive evaluation in this thesis proved by the gas production development in 2006.

宽频带地震数据采集系统的研制

The seismic data acquisition system is the most important equipment for seismic prospecting. The geophysicists have been paying high attention to the specification of the equipment used in seismic prospecting. Its specification and performance are of great concerned to acquire precisely and accurately seismic data, which show us stratum frame. But, by this time, limited by the technology, most of the Broad-band Seismic Recorder (BSR) for lithosphere research of our country were bought from fremdness which were very costliness and maintained discommodiously. So it is very important to study the seismic data acquisition system.The subject of the thesis is the research of the BSR, several items were included, such as: seismic data digitizer and its condition monitor design.In the first chapter, the author explained the significance of the implement of BSR, expatiated the requirement to the device and introduced the actuality of the BSR in our country.In the second chapter, the collectivity architecture of the BSR system was illustrated. Whereafter, the collectivity target and guideline of the performance of the system design were introduced. The difficulty of the system design and some key technology were analyzed, such as the Electro Magnetic Compatibility (EMC), system reliability technology and so on.In the third chapter, some design details of BSR were introduced. In the recorder, the former analog to digital converter (ADC) was separated from the later data transition module. According to the characteristic of seismic data acquisition system, a set high-resolution 24-bit ADC chip was chosen to the recorder design scheme. As the following part, the noise performance of the seismic data channel was analyzed.In the fourth chapter, the embedded software design of each board and the software design of the workstation were introduced. At the same time the communication protocol of the each module was recommendedAt the last part of this thesis, the advantages and the practicability of the BSR system design were summarized, and the next development items were suggested.

中学生抑郁和素质、压力、环境因素的关系及其整合模型研究

As a kind of mood, depression is one of the emotions which people experienced usually. Depressive disorder is one of the common mental diseases. There are about 100 million people in the world be disturbed by depression every year. So it is long history that depression is investigated widely in medicine, psychology, and sociology. There are many theorial problems remain to be solved. Viewed from latest vocuments, the development of depression theory is tending to become more complicated. Most of the prior depression theory focused on relation between one factor and depression. Because depressed individuls have various characteristics and factors that cause depression are different, and each factor can explain only part of depression variance, these prior depression theories are defected. As the knowledge about depression accumulated, the view that depression be caused by multifactor is clearer. There is tendency to integrate these cooperational factor into a model while developing a depression theory. In the present study, depression status of 1625 middle school students from junior 1 to senior 3 are measured using Depression Scale of Middle-school Student which is developed by ourselves. From approach of depressive mood, the present study explored depressive diathesis including attributional style, personality, coping style, and self. The relation among depressive diathesis, stress and depression is analysed. The relation between depression and school life adaptation, depression and cohesion, adaptation in family are also analysed from environmental view. At last, relation among environment, stress, depressive diathesis is examined by using covariance structure modelling. Synthesizing the results from the present study, the following conclusions were drawn: (1) There is grade-characteristics in development of depression in middle school students. Depression degree increased with grade. The main reason may be that the stress middle-school students experience increase and self-acceptance decrease with grade; (2) High depressive diathesis is different from low depressive diathesis. the features of high depressive diathesis are that attributing failure to ability or background, low capacity for status, low sociability, low independence, low self-blame, more illusion. The features of low depressive diathesis are that not attributing failure to ability or background, high capacity for status, high sociability, high independence, high self-acceptance, while facing difficulties, using problem-resolving coping strategy, less self-blame, less illusion. Individuals who have high depressive diathesis showed serious depression, and individuals who have low depressive diathesis showed light depression; (3) Depressive diathesis had accumulative effect on depression. More low depressive diathesis, more light is depression. More high depressive diathesis, more serious is depression; (4) Depressive diathesis can predict present depression and future depression. Predicting present depression is more effective than predicting future depression; (5) Individual who has different depressive diathesis experiences different level of stress. Higher the depressive diathesis individual has, higher stress he will experience. Lower the depressive diathesis individual has, lower stress will he experience; (6) There is correlation between life event pressure and depression. Life event pressure can predict a part of variance of depression. Life event pressure has accumulative effect on depression. More life event and higher life event pressure, more serious depression individual will experience; (7) There exits high correlation between depression and school life adaptation which can predict depression; (8) There is high correlative relation between depression and cohesion, adaptation in family which can predict depression; and (9) Environment have more effect on diathesis than on stress. Diathesis has more effect on depression than stress does. The past depression can predict future depression. This study had enlarged the domain of depressive diathesis such as attributional style, personality, coping style, and self, which are analysed wholly. This study had also enriched the connotation of diathesis=stress theory. Above two aspects are theoretical significance of the study. This study provide a framework of mental health educational curriculum in high school and provide the guideline for prevention and cure of depression. It is the practical significance of this study.