The strength distribution of brittle materials with a high-concentration of cavities

The maximum stress concentration factor in brittle materials with a high concentration of cavities is obtained. The interaction between the nearest cavities, in addition to the far field interactions, is taken into account to evaluate the strength distribution based on the statistical analysis of the nearest distance distribution. Through this investigation, it is found that the interaction between the nearest neighbors is much more important than the far field interactions, and one has to consider it in calculating the strength of brittle materials even if the volume fraction of cavities it contains is small. The other important conclusion is that the maximum stress concentration factor has a wide scattered distribution.

伦纳德琼斯薄膜材料导热系数的分子动力学研究

提出从微观的角度,借助计算机工具,将薄膜破坏发展的细节展现出来的分子动力学研究的思想。使得实验上难以观察的现象变得形象而便于理解。应用分子动力学理论,使用伦纳德琼斯势函数,采用预校正积分法和虚拟外力约束标定方法,模拟薄膜体系的传热系数受体系的密度、温度的影响,同时结合体系粒子的径向分布函数和长程分布函数分析了相应的系统结构特性。另外,采用不同的模拟尺寸获得了低维材料所特有的“高温尺寸效应”。结果显示,导热系数随密度的增加变大,随温度的上升而变大。这些数据现有测量手段是难以得到的,这类模拟可以为研究提供一些

A linkage map of common carp (Cyprinus carpio) based on AFLP and microsatellite markers

P>Common carp (Cyprinus carpio) is an important fish for aquaculture, but genomics of this species is still in its infancy. In this study, a linkage map of common carp based on Amplified Fragment Length Polymorphism (AFLP) and microsatellite (SSR) markers has been generated using gynogenetic haploids. Of 926 markers genotyped, 151 (149 AFLPs, two SSRs) were distorted and eliminated from the linkage analyses. A total of 699 AFLP and 20 microsatellite (SSR) markers were assigned to the map, which comprised 64 linkage groups and covered 5506.9 cM Kosambi, with an average interval distance of 7.66 cM Kosambi. The normality tests on interval map distances showed a non-normal marker distribution. Visual inspection of the map distance distribution histogram showed a cluster of interval map distances on the left side of the chart, which suggested the occurrence of AFLP marker clusters. On the other hand, the lack of an obvious cluster on the right side showed that there were a few big gaps which need more markers to bridge. The correlation analysis showed a highly significant relatedness between the length of linkage group and the number of markers, indicating that the AFLP markers in this map were randomly distributed among different linkage groups. This study is helpful for research into the common carp genome and for further studies of genetics and marker-assisted breeding in this species.

The influence of heat treatment on structures of the aggregated state of polyamide-1010

The structural parameters of the aggregated state of polyamide (PA)-1010 annealed at various temperatures were computed by means of the desmearing intensity from Smalt Angle X-ray Scattering (SAXS) measurements and by using the concept of the distance distribution function. The results indicated that the structural parameters of the aggregated state were strongly dependent upon heat treatment conditions and the maximum values of the structural parameters were obtained for the samples annealed at T = 175 degrees C. The particle size Z annealed at different temperature was ranged between 8.1-12.8nm, and the values of the distance distribution function P-max(Z) were obtained when Z = 4.0-6.8 nm. Using one dimension electron density correlation function (1D EDCF) method long period (L) and thickness of the lamellar (d(0)) were estimated and were found to increase with the increase of the degree of crystallinity.

Small angle X-ray scattering study of structural parameters of the aggregated state in polyamide 1010+BMI

The structural parameters of the aggregated state in the polyamide PA1010 and N,N'-bismaleimide-4,4'-diphenyl methane (BMI) system were computed by means of the desmearing intensity from SAXS and using the concept of the distance distribution function. The results revealed that the parameters Q, I(0), l(c) and L decreased with the increase BMI component, whereas O-s increased. The particle dimension Z for different BMI contents was less than 13.2 nm, and the maximum value of the distance distribution function P(Z) was found to be in the range Z = 6.5-7.0 nm.

The influence of heat treatment on polyamide-1010 structures of the aggregated state

The structural parameters of the aggregated state under various heat treatment for PA-1010 samples were computed by means of the desmearing intensity from SAYS, and by using the concept of the distance distribution function and 1D EDCF method. The results revealed that the maximum values of Q, I(0), P-max(Z), dtr, Rg and W-c,W-x were obtained nearby T=175 degreesC for PA-1010 samples with various annealing treatment. The higher degree of the crystallinity, the greater values of all the structural parameters of the aggregated state for PA-1010 samples were.

An algorithm of analysis tools on points distribution in high dimension space: The distance of a point and an infinite sub-space

This paper discusses the algorithm on the distance from a point and an infinite sub-space in high dimensional space With the development of Information Geometry([1]), the analysis tools of points distribution in high dimension space, as a measure of calculability, draw more attention of experts of pattern recognition. By the assistance of these tools, Geometrical properties of sets of samples in high-dimensional structures are studied, under guidance of the established properties and theorems in high-dimensional geometry.

Stress-distribution around a rigid line in dissimilar media

The elastic plane problem of a rigid line inclusion between two dissimilar media was considered. By solving the Riemann-Hilbert problem, the closed-form solution was obtained and the stress distribution around the rigid line was investigated. It was found that the modulus of the singular behavior of the stress remains proportional to the inverse square root of the distance from the rigid line end, but the stresses possess a pronounced oscillatory character as in the case of an interfacial crack tip.

Distribution of Temperature in GlidArc Discharge Plasma

The GlidArc discharge is one of the main generation methods of non-equilibrium plasma near atmospheric pressures. In general, Gliding Arc discharge is driven by gas flow [1] in axial direction or by magnetic field in circumferential direction. [2] In this paper, a GlidArc discharge driven by rotating-gas-flow in circumferential direction is presented. The principle of the plasma generator is analyzed. The distribution of the temperature in axial direction is measured by a digital thermometer for three different gases. The experimental set-up of the GlidArc plasma is shown in Fig.1. It consists of a center electrode, an outside electrode, a power supply and a gas supply. The shortest distance between the electrodes is 2-3 mm. When a power supply with 10000 volts is attached to the electrodes, the arc will be ignited at the shortest distance. The small plasma column is rotated by the rotating gas flow in circumferential direction and then the rotating arc is driven towards the exit of the setup by the gas flow.

The influence of Saffman lift force on nanoparticle concentration distribution

The lift force on a spherical nanoparticle near a wall in micro/nanofluidics has not received sufficient attention so far. In this letter the concentration of 200 nm particles is measured at 0.25–2.0 m to a wall in a microchannel with pressure-driven de-ionized water flow pressure gradient 0–2000 kPa/m . The measured data show the influence of the lift force on the nanoparticle concentration distribution. By introducing the Saffman lift force into the Nernst–Planck equation near a wall, we find that the lift force is dominant at the range of 2distance from the wall).

Hydroacoustic study of spatial and temporal distribution of Gymnocypris przewalskii (Kessler, 1876) in Qinghai Lake, China

Gymnocypris przewalskii (Kessler 1876) is an endangered and state-protected rare fish species in Qinghai Lake, China. To further understand the life history and distribution of this fish, five surveys were carried out in Qinghai Lake between 2002-2006. Results of these surveys indicate that fishes were predominantly distributed about 2 m under the surface. In July, significant differences in fish density were found between surface and bottom layers (P = 0.001), and/or between middle and bottom layers (P = 0.025). Fish density was the greatest in the surface layer. In August and October, no significant differences were found between the different layers, but the bottom layer had a greater fish density. Furthermore, there were very large differences among different zones in fish distribution density. Differences in horizontal distribution were not significantly correlated to factors such as water depth and inshore distance, possibly because of very low and uniform fish density. Feeding, changes in water temperature, over-wintering and spawning appeared to influence fish distribution. Hydroacoustic estimates of G. przewalskii biomass in Qinghai Lake increased significantly between 2002 and 2006. We attribute this increase to the management measures put in place to protect this species.

Influence of heated catalyzer on thermal distribution of substrate in HWCVD system

Based on Stefan-Boltzman and Lambert theorems, the radiation energy distribution on substrate (REDS) from catalyzer with parallel filament geometry has been simulated by variation of filament and system layout in hot-wire chemical vapor deposition. The REDS uniformity is sensitive to the distance between filament and substrate d(f-s) when d(f-s) less than or equal to 4 cm. As d(f-s) > 4 cm, the REDS uniformity is independent of d(f-s) and is mainly determined by filament number and filament separation. Two-dimensional calculation shows that the REDS uniformity is limited by temperature decay at filament edges. The simulation data are in good agreement with experiments. (C) 2003 Elsevier Science B.V. All rights reserved.

Influence of heated catalyzer on thermal distribution of substrate in HWCVD system

Based on Stefan-Boltzman and Lambert theorems, the radiation energy distribution on substrate (REDS) from catalyzer with parallel filament geometry has been simulated by variation of filament and system layout in hot-wire chemical vapor deposition. The REDS uniformity is sensitive to the distance between filament and substrate d(f-s) when d(f-s) less than or equal to 4 cm. As d(f-s) > 4 cm, the REDS uniformity is independent of d(f-s) and is mainly determined by filament number and filament separation. Two-dimensional calculation shows that the REDS uniformity is limited by temperature decay at filament edges. The simulation data are in good agreement with experiments. (C) 2003 Elsevier Science B.V. All rights reserved.

Spatial distribution of soil heavy metal pollution estimated by different interpolation methods: Accuracy and uncertainty analysis

Mapping the spatial distribution of contaminants in soils is the basis of pollution evaluation and risk control. Interpolation methods are extensively applied in the mapping processes to estimate the heavy metal concentrations at unsampled sites. The performances of interpolation methods (inverse distance weighting, local polynomial, ordinary kriging and radial basis functions) were assessed and compared using the root mean square error for cross validation. The results indicated that all interpolation methods provided a high prediction accuracy of the mean concentration of soil heavy metals. However, the classic method based on percentages of polluted samples, gave a pollution area 23.54-41.92% larger than that estimated by interpolation methods. The difference in contaminated area estimation among the four methods reached 6.14%. According to the interpolation results, the spatial uncertainty of polluted areas was mainly located in three types of region: (a) the local maxima concentration region surrounded by low concentration (clean) sites, (b) the local minima concentration region surrounded with highly polluted samples; and (c) the boundaries of the contaminated areas. (C) 2010 Elsevier Ltd. All rights reserved.