Theoretical design and performance of InxGa1-xN two-junction solar cells

The efficiencies of InxGa1-xN two-junction solar cells are calculated with various bandgap combinations of subcells under AM1.5 global, AM1.5 direct and AM0 spectra. The influence of top-cell thickness on efficiency has been studied and the performance of InxGa1-xN cells for the maximum light concentration of various spectra has been evaluated. Under one-sun irradiance, the optimum efficiency is 35.1% for the AM1.5 global spectrum, with a bandgap combination of top/bottom cells as 1.74 eV/1.15 eV. And the limiting efficiency is 40.9% for the highest light concentration of the AM1.5 global spectrum, with the top/bottom cell bandgap as 1.72 eV/1.12 eV.

Optimized design on high-power GaN-based Micro-LEDs - art. no. 684108

The structure of micro-LEDs was optimized designed. Optical, electrical and thermal characteristics of micro-LEDs were improved. The optimized design make micro-LEDs suitable for high-power device. The light extraction efficiency of micro-LEDs was analyzed by the means of ray tracing. The results shows that increasing the inclination angle of sidewall and height of mesa, and reducing the absorption of p and n electrode can enhance the light extraction efficiency of micro-LEDs. Furthermore, the total light output power can be boosted by increasing the density of micro-structures on the device. The high-power flip-chip micro-LEDs were fabricated, which has higher quantum efficiency than conventional BALED's. When the number of microstructure in micro-LEDs was increased by 57%, the light output power was enhanced 24%. Light output power is 82.88mW at the current of 350mA and saturation current is up to 800mA, all of these are better than BALED which was fabricated in the same epitaxial wafer. The IN characteristics of micro-LEDs are almost identical to BALED.

Color filter-less technology of LED back light for LCD-TV - art. no. 68410G

Back Light Unit (BLU) and Color Filter are the two key components for the perfect color display of Liquid Crystal Display (LCD) device. LCD can not light actively itself, so a form of illumination, Back Light Unit is needed for its display. The color filter which consists of RGB primary colors, is used to generate three basic colors for LCD display. Traditional CCFL back light source has several disadvantages, while LED back light technology makes LCD obtain quite higher display quality than the CCFL back light. LCD device based on LED back light owns promoted efficiency of display. Moreover it can generate color gamut above 100% of the NTSC specification. Especially, we put forward an idea of Color Filter-Less technology that we design a film which is patterned of red and green emitting phosphors, then make it be excited by a blue light LED panel we fabricate, for its special emitting mechanism, this film can emit RGB basic color, therefore replace the color filter of LCD device. This frame typically benefits for lighting uniformity and provide pretty high light utilization ratio. Also simplifies back light structure thus cut down the expenses.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Study of the LED based light calibration system for neutron wall detector

The light calibration system is one of the key components of Neutron Wall detector. It is used to calibrate the electronics and to monitor the long-term stability of the detector modules. With the detaile investigations, a calibration system with high-power LED (3W) driven by the fast pulses has been carried out. It is also tested together with the detector module of the Neutron Wall and the result of the preliminary calibration demonstrates that it fulfills the needs. It's a new design proposal to the light calibration system of the fast scintillator detector.

动漫行业创业者胜任特征研究

Venture has become an important force for the sustainable economic growth of China, However, research on entrepreneurs is far failed to meet the actual needs, Animation and Comic Industry is an important component of the state-led Cultural and Creative Industries. Entrepreneurship is the rapid growth of population, but the empirical research on the Animation and Comic Industry entrepreneurs’ Competent Characteristic Model is rarely heard. As a manager of a national incubator which major in Cultural and Creative Industry, study these entrepreneurs competent characteristics is my responsibility. As an exploration, the study uses Competent Characteristic Model of classical design methods and behavior events interview method, and selects entrepreneurs which of animation and comic industry business start-up period as the objects. Through coding analysis of 31 entrepreneurs’ interview information, completed the amendment to the dictionary coding, and ultimately construct the animation and comic industry entrepreneurs need to have the threshold competence model and differentiating competence model. Differentiating competence model includes six competencies: tolerance and optimism, cooperation, creative innovation, pool talents, vision, decision-making and tempo control. Threshold competence model includes twenty features, divided into three dimensions: personal characteristics, knowledge quality, capacity of the quality. Knowledge and capacity of the quality are closely related to the core work of entrepreneurs, Personal characteristics concern the deep-seated motivation of the entrepreneurs. The study also analyses and discusses the characteristics of the entrepreneurs on the demographic variables.