Delay of the excited state lasing of 1310 nm InAs/GaAs quantum dot lasers by facet coating

In this letter, we present a facet coating design to delay the excited state (ES) lasing for 1310 nm InAs/GaAs quantum dot lasers. The key point of our design is to ensure that the mirror loss of ES is larger than that of the ground state by decreasing the reflectivity of the ES. In the facet coating design, the central wavelength is at 1480 nm, and the high- and low-index materials are Ta2O5 and SiO2, respectively. Compared with the traditional Si/SiO2 facet coating with a central wavelength of 1310 nm, we have found that with the optimal design the turning temperature of the ES lasing has been delayed from 90 to 100 degrees C for the laser diodes with cavity length of 1.2 mm. Furthermore, the characteristic temperature (T-0) of the laser diodes is also improved.

The time delay in electrochemical measurements of a finite-volume system

For a sphere electrode enclosed in finite-volume electrolyte, the measured current will deviate from the result predicted by the semi-infinite diffusion theory after some time. By random-walk simulation, we compared this time to the one needed for diffusion layer to reach electrolyte boundary, and revealed a clear signal delay of electrochemical current. Further we presented a quantitative description of this delay time. The simulation results suggested that the semi-infinite diffusion theory can even be applied when the theoretical diffusion layer grows to 1.28 electrolyte thicknesses, with an accuracy better than 0.5%. We attributed this time delay to the molecules' finite propagation velocity. Finally, we discussed how this delay can influence and facilitate the following electrochemical detection towards the nanometer and single-cell scale.

Spatiotemporal behaviors and singularity of ultrashort pulsed Elegant Hermite-Gaussian beams

Analytical propagation expressions of ultrashort pulsed Elegant Hermite-Gaussian beams are derived and spatiotemporal properties of the pulses with different transverse modes are studied. Singularity of the complex amplitude envelope solution of the pulses obtained under slowly varying envelope approximation is analyzed in detail. The rigorous analytical solution of the pulse is deduced and no singularity emerges in the solution. The obtained results indicate that the transverse mode affects not only the spatiotemporal properties but also the singularity of the pulses. Time delay of the off-axis maximum intensity is more obvious and the singularity is located nearer to the z-axis for the pulse with higher transverse modes. (C) 2007 Elsevier GmbH. All rights reserved.

The reproductive strategies of an endemic Tibetan fish, Gymnocypris selincuoensis

The reproductive traits of Gymnocypris selincuoensis from Selincuo Lake and its tributaries were investigated in 1997 and 1998. The youngest mature male was age 7 with a standard length (SL) of 172.0 mm, and the youngest mature female was age 8 with a SL of 194.0 mm. The L(50)s Of SL and age at first maturity were respectively 250.32 mm and age 9 for males and 224.71 mm and age 8 for females. The gonadosomatic index (GSI) significantly changed with seasons for mature individuals but not for immature individuals. GSIs of mature females at stages IV and V of ovary development increased with SL and reached a maximum value at the SL range from 370 mm to 390 mm; the GSIs of mature males were negatively correlated with SL. The breeding season lasted from early April to early August. Egg size did not significantly change with SL but increased with the delay of spawning. The individual absolute fecundity varied from 1,341 to 28,002 eggs (mean 12,607+/-7,349), and the individual relative fecundity varied from 6.4 to 42.0 eggs.g(-1) (mean 25.5+/-9.7). The individual fecundity increased with total body weight; it also increased with SL for those of SL less than 370 mm. There was a rest of spawning for mature individuals.

The reproductive strategies of an endemic Tibetan fish, Gymnocypris selincuoensis

The reproductive traits of Gymnocypris selincuoensis from Selincuo Lake and its tributaries were investigated in 1997 and 1998. The youngest mature male was age 7 with a standard length (SL) of 172.0 mm, and the youngest mature female was age 8 with a SL of 194.0 mm. The L(50)s Of SL and age at first maturity were respectively 250.32 mm and age 9 for males and 224.71 mm and age 8 for females. The gonadosomatic index (GSI) significantly changed with seasons for mature individuals but not for immature individuals. GSIs of mature females at stages IV and V of ovary development increased with SL and reached a maximum value at the SL range from 370 mm to 390 mm; the GSIs of mature males were negatively correlated with SL. The breeding season lasted from early April to early August. Egg size did not significantly change with SL but increased with the delay of spawning. The individual absolute fecundity varied from 1,341 to 28,002 eggs (mean 12,607+/-7,349), and the individual relative fecundity varied from 6.4 to 42.0 eggs.g(-1) (mean 25.5+/-9.7). The individual fecundity increased with total body weight; it also increased with SL for those of SL less than 370 mm. There was a rest of spawning for mature individuals.

Transient and nonlinear analysis of slow-light pulse propagation in an optical fiber via stimulated Brillouin scattering

We investigate slow-light pulse propagation in an optical fiber via transient stimulated Brillouin scattering. Space-time evolution of a generating slow-light pulse is numerically calculated by solving three-wave coupled-mode equations between a pump beam, an acoustic wave, and a counterpropagating signal pulse. Our mathematical treatments are applicable to both narrowband and broadband pump cases. We show that the time delay of 85% pulse width can be obtained for a signal pulse of the order of subnanosecond pulse width by using a broadband pump, while the signal pulse is broadened only by 40% of the input signal pulse. The physical origin of the pulse broadening and distortion is explained in terms of the temporal decay of the induced acoustic field. (C) 2009 Optical Society of America

Reducing group-velocity-dispersion-dependent broadening of stimulated Brillouin scattering slow light in an optical fiber by use of a single pump laser

We propose a method of effectively extending the stimulated Brillouin scattering (SBS) gain bandwidth in a single-mode optical fiber to reduce group-velocity-dispersion (GVD)-dependent pulse spread of SBS slow light. This can be done by overlapping doublet SBS gain spectra synthesized from a single pump laser. Numerical calculations are performed to verify our proposed method. We find that there exists the optimum spectral separation between two center frequencies of the doublet SBS gain spectrum with respect to the inherent spectral width of the pump laser, which makes it possible to effectively reduce the signal pulse broadening due to GVD. We show that the maximum time delay of the amplified signal pulse can be approximately two times longer than that by a previously reported method using a single broadband pump laser. (c) 2008 Optical Society of America.

Rifting process and formation mechanisms of syn-rift stage prolongation in the deepwater basin, northern South China Sea

Based on the latest seismic and geological data, tectonic subsidence of three seismic lines in the deepwater area of Pearl River Mouth Basin (PRMB), the northern South China Sea (SCS), is calculated. The result shows that the rifting process of study area is different from the typical passive continental margin basin. Although the seafloor spreading of SCS initiated at 32 Ma, the tectonic subsidence rate does not decrease but increases instead, and then decreases at about 23 Ma, which indicates that the rifting continued after the onset of seafloor spreading until about 23 Ma. The formation thickness exhibits the same phenomenon, that is the syn-rift stage prolonged and the post-rift thermal subsidence delayed. The formation mechanisms are supposed to be three: (1) the lithospheric rigidity of the northern SCS is weak and its ductility is relatively strong, which delayed the strain relaxation resulting from the seafloor spreading; (2) the differential layered independent extension of the lithosphere may be one reason for the delay of post-rift stage; and (3) the southward transition of SCS spreading ridge during 24 to 21 Ma and the corresponding acceleration of seafloor spreading rate then triggered the initiation of large-scale thermal subsidence in the study area at about 23 Ma.

Single attosecond pulse generation using two-color polarized time-gating technique

It is proposed that single attosecond pulses be generated via high-order harmonic generation by using a two-color pump pulse with time dependent ellipticity. The two-color pump pulse is created by the fundamental field and its second harmonic: the fundamental field is left-circularly polarized and the second harmonic is right-circularly polarized. Numerical simulations show that single attosecond pulses can be produced in the cut-off region by using the synthesis of 20 fs left-hand and right-hand circularly polarized pulses with a pulse delay of 20 fs. The attosecond pulses produced this way are much stronger than that produced by a few-cycle linear polarized pulse of comparable intensity. (c) 2005 Optical Society of America

参变过程中的群速延迟对晶体匹配长度的影响

基于能量守恒和三波耦合波方程, 建立了超短脉冲在参变过程中二次谐波产生时的I类和II类相位匹配条件、基波与谐波之间的群速延迟时间、以及群速失配对晶体长度限制的理论基础。以负单轴非线性光学晶体CsLiB6O10为例, 分析和数值计算了超短脉冲宽度为100 fs时, 谐波的群速匹配长度随基波波长变化的规律。研究结果表明在I类相位匹配条件下, 基波波长为642 nm时, 群速延迟最小, 相应的群速匹配晶体长度最长为19.1 mm;在II类相位匹配条件下, 基波波长为767 nm, 群速延迟最小, 群速匹配长度最

钛宝石激光器中用优化Gires-Tournois镜产生15fs脉冲

根据飞秒脉冲锁模钛宝石激光器脉冲压缩的要求，介绍了负色散镜补偿色散的基本原理及其特点。详细阐述了优化Gires-Tournois(OG-T)镜的设计过程，并通过计算机优化得到理想设计膜系。采用离子束溅射的方法镀制了优化Gires—Tournois镜。测量了优化Gires-Tournois镜(编号为OGT#1)的透射率和群延迟色散，并与设计值进行了比较，分析了实测值产生偏差的原因，从而对镀膜参量进行了相应的调整，制造了第二批优化Gires—Tournois镜(编号为OGT#2)。将优化Gires—Tourn

Thermal annealing effect on InAs/InGaAs quantum dots grown by atomic layer molecular beam epitaxy

The effect of rapid thermal annealing on the InAs quantum dots (QDs) grown by atomic layer molecular beam epitaxy and capped with InGaAs layer has been investigated using transmission electron microscopy and photoluminescence (PL). Different from the previously reported results, no obvious blueshift of the PL emission of QDs is observed until the annealing temperature increases up to 800 degreesC. The size and shape of the QDs annealed at 750 degreesC have hardly changed indicating the relatively weak Ga/In interdiffusion, which is characterized by little blueshift of the PL peak of QDs. The QD size increases largely and a few large clusters can be observed after 800 degreesC RTA, implying the fast interdiffusion and the formation of InGaAs QDs. These results indicate that the delay of the blueshift of the PL peak of QDs is correlated with the abnormal interdiffusion process, which can be explained by two possible reasons: the reduction of excess-As-induced defects and the redistribution of In, Ga atoms around the InAs QDs resulted from the sub-monolayer deposition of InGaAs capping layer. (C) 2004 Elsevier B.V. All rights reserved.

Ultra-compact silicon-on-insulator optical filter based on sidewall Bragg grating

Micro-cavity structure composed of silicon wire with 240nm square cross section and two symmetrical sidewall waveguide Bragg gratings is fabricated and studied for the operation under telecommunication wavelengths. Optical filter of quasi-TE mode was realized based on this cavity. In such micro-cavity, optical quality factor (Q) was measured up to 380 with a 4.8nm free spectral range (FSR) and 12dB fringe contrast (FC). The measured group index of silicon waveguide with only 240nm square cross section was between 3.80 and 5.43. It is the first time group delay of silicon wire waveguide with such small core dimension is studied. Larger group delay can be expected after optimizing the design parameters and the fabrication process.

Pipeline Architecture and Parallel Computation-Based Real-Time Stereovision Tracking System for Surgical Navigation

This paper studies the development of a real-time stereovision system to track multiple infrared markers attached to a surgical instrument. Multiple stages of pipeline in field-programmable gate array (FPGA) are developed to recognize the targets in both left and right image planes and to give each target a unique label. The pipeline architecture includes a smoothing filter, an adaptive threshold module, a connected component labeling operation, and a centroid extraction process. A parallel distortion correction method is proposed and implemented in a dual-core DSP. A suitable kinematic model is established for the moving targets, and a novel set of parallel and interactive computation mechanisms is proposed to position and track the targets, which are carried out by a cross-computation method in a dual-core DSP. The proposed tracking system can track the 3-D coordinate, velocity, and acceleration of four infrared markers with a delay of 9.18 ms. Furthermore, it is capable of tracking a maximum of 110 infrared markers without frame dropping at a frame rate of 60 f/s. The accuracy of the proposed system can reach the scale of 0.37 mm RMS along the x- and y-directions and 0.45 mm RMS along the depth direction (the depth is from 0.8 to 0.45 m). The performance of the proposed system can meet the requirements of applications such as surgical navigation, which needs high real time and accuracy capability.

Pipeline Architecture and Parallel Computation-Based Real-Time Stereovision Tracking System for Surgical Navigation

This paper studies the development of a real-time stereovision system to track multiple infrared markers attached to a surgical instrument. Multiple stages of pipeline in field-programmable gate array (FPGA) are developed to recognize the targets in both left and right image planes and to give each target a unique label. The pipeline architecture includes a smoothing filter, an adaptive threshold module, a connected component labeling operation, and a centroid extraction process. A parallel distortion correction method is proposed and implemented in a dual-core DSP. A suitable kinematic model is established for the moving targets, and a novel set of parallel and interactive computation mechanisms is proposed to position and track the targets, which are carried out by a cross-computation method in a dual-core DSP. The proposed tracking system can track the 3-D coordinate, velocity, and acceleration of four infrared markers with a delay of 9.18 ms. Furthermore, it is capable of tracking a maximum of 110 infrared markers without frame dropping at a frame rate of 60 f/s. The accuracy of the proposed system can reach the scale of 0.37 mm RMS along the x- and y-directions and 0.45 mm RMS along the depth direction (the depth is from 0.8 to 0.45 m). The performance of the proposed system can meet the requirements of applications such as surgical navigation, which needs high real time and accuracy capability.