Restructuring of a zooplankton community by perturbation from a wind-forced coastal jet

The impact of transient wind events on an established zooplankton community was observed during a, field survey in a, coastal region off northern Norway in May 2002. A transient wind event induced a coastal jet/filament intrusion of warm, saline water into our survey area where a semi-permanent eddy was present. There was an abrupt change in zooplankton community structure within 4-7 days of the wind event, with a change in the size structure, an increase in lower size classes less than 1 mm in equivalent spherical diameter (ESD) and a decrease in larger size classes greater than 1.5 mm in ESD. The slope of zooplankton biovolume spectra changed from -0.6 to -0.8, consistent with the size shifting towards smaller size classes. This study shows that even well established zooplankton communities are susceptible to restructuring during transient wind events, and in particular when wind forcing induces horizontal currents or filaments.

Characteristics of a CW HF chemical-laser calculated from a simplified two-dimensional model

A two-dimensional simplified model of an HF chemical laser is introduced. Using an implicit finite difference scheme, the solution of two adjacent parallel streams with diffusion mixing and chemical reaction is generated. A contour of mixing and reaction boundary is obtained without presupposition. The distribution of the HF(v) concentrations, gas temperature and the optical small signal gain (alpha sub V, J) on the flowing plane (X, Y) are presented. Compared with the solution solved directly from a set of Navier-Stokes equations, the results of these two methods agree with each other qualitatively. The influences of the different velocity, temperature (T sub 0) and composition of the two streams on the small signal gain after the nozzle exit are investigated. It is interesting that for larger J with a fixed v, the peaks of alpha sub v-T sub 0 profiles move towards higher T sub 0. The computing method is simple and only a short computing time is needed.

Three-dimensional finite element analysis of composites with coated spherical inclusions

A three-dimensional finite element analysis has been used to determine the internal stresses in a three-phase composite. The stresses have been determined for a variety of interphase properties, the thicknesses of the interphase and the volume fractions of particles. Young's modulus has been calculated from a knowledge of these stresses and the applied deformation. The calculations show that stress distributions in the matrix and the mechanical properties are sensitive to the interphase property in the three-phase composites. The interfacial stresses in the three-dimensional analysis are in agreement with results obtained by an axisymmetric analysis. The predicted bulk modulus in three-dimensional analysis agrees well with the theoretical solution obtained by Qui and Weng, but it presents a great divergence from that in axisymmetric analyses. An investigation indicates that this divergence may be caused by the difference in the unit cell structure between two models. A comparison of the numerically predicted bulk and shear modulus for two-phase composites with the theoretical results indicates that the three-dimensional analysis gives quite satisfactory results.

An Energy-Based Method for Analyzing Instrumented Spherical Indentation Experiments

Using dimensional analysis and finite element calculation, we studied spherical indentation in elastic-plastic solids with work hardening. We report two previously unknown relationships between hardness, reduced modulus, indentation depth, indenter radius, and work of indentation. These relationships, together with the relationship between initial unloading stiffness and reduced modulus, provide an energy-based method for determining contact area, reduced modulus, and hardness of materials from instrumented spherical indentation measurements. This method also provides a means for calibrating the effective radius of imperfectly shaped spherical indenters. Finally, the method is applied to the analysis of instrumented spherical indentation experiments on copper, aluminum, tungsten, and fused silica.

Relationships between Initial Unloading Slope, Contact Depth, and Mechanical Properties for Spherical Indentation in Linear Viscoelastic Solids

Using analytical and finite element modeling, we examine the relationships between initial unloading slope, contact depth, and mechanical properties for spherical indentation in viscoelastic solids with either displacement or load as the independent variable. We then investigate whether the Oliver-Pharr method for determining the contact depth and contact radius, originally proposed for indentation in elastic and elastic-plastic solids, is applicable to spherical indentation in viscoelastic solids. Finally, the analytical and numerical results are used to answer questions raised in recent literature about measuring viscoelastic properties from instrumented spherical indentation experiments.

Even aberration measurement of lithographic projection system based on optimized phase-shifting marks

In the present paper, we propose a novel method for measuring the even aberrations of lithographic projection optics by use of optimized phase-shifting marks on the test mask. The line/space ratio of the phase-shifting marks is optimized to obtain the maximum sensitivities of Zernike coefficients corresponding to even aberrations. Spherical aberration and astigmatism can be calculated from the focus shifts of phase-shifting gratings oriented at 0 degrees, 45 degrees, 90 degrees and 135 degrees at multiple illumination settings. The PROLITH simulation results show that, the measurement accuracy of spherical aberration and astigmatism obviously increase, after the optimization of the measurement mark. (C) 2008 Elsevier B.V. All rights reserved.

Age and growth of an endemic cyprinid fish, Spinibarbus yunnanensis, from Lake Fuxian, China

Age and growth of Spinibarbus yunnanensis Tsu in Lake Fuxian were investigated by examination of annuli from scales, dorsal fin spines, and otoliths. Sectioned otoliths exhibited the clearest and the most regular annuli. The formation of false annuli, which regularly arose on scales and dorsal fin spines during the juvenile stage, may be caused by a change in diet during development. The parameters for the von Bertalanffy growth curve were: K = 0.105, L-infinity = 950 mm, t(0) = -0.22 year for both sexes. W-infinity, calculated from the relationship W-infinity = aL(infinity)(b), was 10,352 g.

Application and validation of a new biotic index using data from several water systems

Protozoans of Lake Donghu were collected from five stations using the PFU method. The sampling was conducted for one year and two times a month. The aim of this research was to test the applicability of a new protozoa biotic index, species pollution value (SPV) and community pollution value (CPV), established by the authors using data from the River Hanjiang. Each station's CPV was calculated from the SPV and the correlation analysis between the CPV and the comprehensive chemical index of stations I, II, III showed a significant correlation between them. The pollution status of the five stations was correctly evaluated by the CPV. These results suggested that the biotic index could be applied in water systems other than the River Hanjiang. The SPV of some protozoa species in Lake Donghu, not observed in the River Hanjiang were established. In order to further test the applicability of the biotic index, protozoan and chemistry data from the Rivers Torrente Stirone and Parma of Italy were used. The results showed that the CPV for the two rivers had a close relationship with the chemical water quality, which indicated that the biotic index could be applied in other parts of the world for the monitoring and estimating of water quality. Since the results of testing and verifying the biotic index in some other water systems in China were also satisfactory, this indicated that the biotic index has an extensive suitability for freshwater ecosystems. As long as more than 50% of the species in a sample have a SPV, the CPV calculated from the SPV is reliable for monitoring and evaluating water quality.

应用负载型纳米铁去除饮用水中砷的研究

砷是毒性最强的元素之一，水体中砷的污染己经引起人们广泛的关注。我国的新疆、内蒙、山西和台湾等省和地区地下水砷含量严重超标。全球共有5,000多万人遭受高砷饮用水的威胁，其中中国有1,500多万，是饮用水砷污染最严重的国家之一。WHO推荐饮用水砷的最高允许浓度从原来的50 µg•L-1已降至10 µg•L-1。更为严格的砷卫生标准的颁布，对作为饮用水源的地下水中的砷去除工艺提出了更高的要求。吸附法除砷比膜法、混凝法和离子交换法更安全、简便，是砷去除工艺中最有效的方法之一。 首先，本研究通过优化制备条件（包括炭种类的选择、炭的粒径大小、还原剂的浓度及滴定速率、反应温度、铁盐的种类及浓度、分散剂的比例及浓度），制备了负载型纳米铁。考虑到砷的去除效率、工程应用的可行性以及经济性，最优的制备条件如下：选用粒径为20~40目煤质炭，在室温、一定的分散剂比例及浓度，0.2 M KBH4滴速为20 d•min-1时所制备的Fe/炭为82.0 mg•g-1；纳米铁在活性炭孔内呈针状，其直径为30~500 nm，长度为1,000~2,000 nm。绝大多数的铁都负载到活性炭内部，这在处理水时铁不流失很重要。 其次，利用制备的负载型纳米铁作吸附载体，进行了饮用水中As(Ⅴ)的吸附去除实验。研究了该吸附剂对As(Ⅴ)的吸附等温线、动力学以及影响动力学的各种因素（包括As(Ⅴ)的不同初始浓度、吸附剂用量、pH值、共存离子和不同温度）、pH值、共存离子等环境条件对As(Ⅴ)去除的影响；以及吸附剂的再生及再生后的吸附效率等。研究发现在前12 h内吸附较快，72 h时达到了平衡。用Langmuir 吸附等温式估算出As(Ⅴ)的吸附量为12.0 mg•g-1。该吸附剂在pH 6.5， (25±2)℃， As(Ⅴ)初始浓度为2 mg•L-1，吸附剂用量为1.0 g•L-1时，As(Ⅴ)的去除率为75.2%；当把吸附剂的用量增加到1.5 g•L-1时，As(Ⅴ)的去除率可达99.9%以上。吸附剂可以用0.1M的NaOH浸泡12 h后即可再生，再生效率较高。常见的阴离子中PO43-、SiO32-对As(Ⅲ)的去除抑制较大，而SO42-、CO32-、C2O42-等离子对砷的去除影响较小。Fe2+对As(Ⅲ)的吸附抑制作用较大而其它阳离子影响不大。吸附剂可用0.1 M NaOH 有效再生，并且具有良好的机械性能。实验室初步实验数据表明，该吸附剂对饮用水除砷具有较好的应用前景。 第三，利用实验室制备的负载型纳米铁对饮用水中As(Ⅲ)的吸附去除也进行了研究。考察了吸附等温线、动力学以及影响动力学的各种因素、pH值、共存离子等环境条件对As(Ⅲ)去除的影响；以及吸附剂的再生及再生后的吸附效率等。研究发现，该吸附剂在pH 6.5， (25±2)℃， As(Ⅲ)初始浓度为2 mg•L-1，吸附剂用量为1.0 g•L-1时， 对As(Ⅲ)的去除率为99.8%；其吸附容量为1.996mg•g-1。吸附过程中部分As(Ⅲ)被氧化。与As(Ⅴ)的吸附相比，该吸附剂对As(Ⅲ)的效率比较高-而常见的其它除砷吸附剂如载铁纤维棉等，对As(Ⅴ)的效率比As(Ⅲ)高，为有效去除As(Ⅲ)，常常需要专门加上氧化这一过程。 最后，利用负载型纳米铁对饮用水中As(Ⅲ) 的氧化性能进行考察，发现该吸附剂不但能够有效吸附去除饮用水中的砷，而且还能把As(Ⅲ)有效地氧化为As(Ⅴ)。经过对吸附剂的构成组分分析发现，活性炭表面因富含多种官能团而对三价砷的氧化作用最大；其次是纳米铁也能把As(Ⅲ)氧化为As(Ⅴ)。

Active site structure of NO decomposition on perovskite(-like) oxides: An investigation from experiment and density functional theory

Active site structure for NO decomposition carried out on perovskite-like oxides were discussed based on the N-2 yield measured from LaSrNi1-x,AlxO4 with different B-site cations and from La2-ySryCuO4 with different crystal phases. Results show that the active site contains two oxygen vacancies, two transition metals, and one lattice-oxygen, with the oxygen vacancy locating on the apex of MO6 octahedron, and the lattice oxygen locating between the two transition metals (i.e., M-O-M plane). Density functional theory (DFT) analysis to the structure shows that this new active site is the most active structure for NO adsorbing, and hence, for NO decomposition. The similar trend of the relative energies that are required for the formation of oxygen vacancies with f form (calculated from DFT), the amount of oxygen vacancies, and the activities (N-2 yield) certifies this result further.

Conductive behavior and ionic conductivity of composite polymer electrolytes

The ac impedance plots of ( PEO)(16) LiClO4-EC composite polymer electrolytes were studied. The equivalent circuit of stainless steel electrode(SS)/composite electrolyte/SS system was applied to explain the ac impedance plots, The results showed that the equivalent circuit could fit the experimental data very well. The ionic conductivity was calculated using the bulk resistance that was obtained from equivalent circuit. The effect of EC on the conductive behavior was explained by the interactions among different species formed in the composite polymer electrolytes. For lower EC concentration samples, the temperature dependence of conductivity in low temperature range followed Arrhenius type, but when EC concentration was larger than 20%, the temperature dependence of conductivity obeyed the Vogel-Tamman-Fulcher (VTF) equation in all temperature ranges.

Impedance study of (PEO)(10)LiClO4-Al2O3 composite polymer electrolyte with blocking electrodes

A composite solid polymer electrolyte (SPE) of (PEO)(10)LiClO4-Al2O3 was prepared and Pt and stainless steel(SS) blocking electrodes were used for an impedance study. It was found that the semicircle in the high frequency range and the straight line in the low frequency range depend upon different blocking electrodes and polarization potentials applied in the experiments. In the equivalent circuit. two constant phase elements (CPE) have been used instead of the pure geometrical and double layer capacitances. respectively. A theoretical line calculated from their estimated values has a good correlation with the experiment data. Moreover. the equivalent circuit also can be used to explain the impedance properties of Pt and stainless steel (SS) blocking electrodes both in the high and the low frequency ranges. (C) 2001 Elsevier Science Ltd. All rights reserved.

Kinetic isotope effects of proton transfer reaction for amines by ultrasonic relaxation methods: Unexpected evidence from the results in ethylamine solutions

Ultrasonic absorption coefficients for ethylamine in heavy water (D2O) and in light water (H2O) have been measured in the frequency range from 0.8 to 220 MHz at 25 degrees C. A single relaxational process has been observed in these two kinds of solutions. From the concentration dependence of the ultrasonic relaxation parameters, and following the reaction mechanism proposed by Eigen et al. for ethylamine in H2O, the causes of the relaxations have been attributed to a perturbation of an equilibrium associated with a deuteron or proton transfer reaction. The rate and equilibrium constants have been estimated from deuterioxide or hydroxide ion concentration dependence of the relaxation frequency, and the kinetic isotope effects have been determined. In addition, the standard volume changes of the reactions have been calculated from the concentration dependence of the maximum absorption per wavelength, and the adiabatic compressibility has also been determined from the density and sound velocity for ethylamine in D2O and in H2O, respectively. These results are compared with those for propylamine and butylamine and are discussed in relation to the different kinetic properties between D2O and H2O, the reaction radii derived by Debye theory, and the structural properties of the reaction intermediate.

Tectonic and geodynamic pattern of marginal seas on the West Pacific inferred from multi-satellite altewetry geoid

With the rapid development of satellite observations, we can use the altimetry geoid to study submarine tectonics and geodynamics. On the basis of the 4' x 4' geoid undulation calculated from altimeter data of Geosat, ERS-1/2 and Topex/Poseidon on the West Pacific, located between 0degreesN similar to 45degreesN, 100degreesC similar to 150degreesE, Bouguer, Glenni and isostatic geoid undulation are obtained from correction of gravitational potential of the global topography and isostacy. Moho discontinuity depth is inversed by the Glenni geoid undulation, and the stress field from small-scale mantle convection is reasonably calculated from the isostatic geoid undulation. The results show that within the Philippine Sea and the South China Sea, short-wavelength lineations of the geoid undulation are parallel or cross to magnetic lineations and rifting ridges. The Moho depth of marginal sea basins becomes shallow southward, and its values are similar to that of the Philippine Sea. These facts show that strength of tectonic activities are almost the same on the both sides of the Ryukyu-Taiwan-Philippine are. Various kinds of tectonic features with different driving mechanisms of small-middle and large-scale of mantle convection, however, display a special pattern of tectonics and geodynamics of the continental marginal seas distinguished from oceans and continents.

Mineral chemistry and its genetic significance of olivine in Cenozoic basalts from the South China Sea

We dredged lots of Cenozoic basalts from areas covered from the northern sub-slope to the southern sub- slope of the South China Sea. Based on the study on mineral chemistry of clinopyroxenes in these Cenozoic hasalts, this paper indicates that pyroxenes are mostly enstatite and a few of augite, sahlite and Ca-rich pyroxene. Pyroxene microlite has higher content in, Ca, Ti and Fe than pyroxene phenocryst, it may reflect that the evolution trend of host magma of pyroxene is coincidence with that of alkali rock series. The depth of magma chambers which calculated from equilibrium temperatures and pressures between clinopyroxene and melt are as follows, that of magma of tephrite is about 49km, that of magma of trachybasalt is about 25km, and that of magma of basalt is about 15km. Correspondingly, Equilibrium temperatures( K) of three types rocks mentioned above gradually decrease from 1535 1498 to 1429 to 1369. By using discriminant plot which developed from pyroxene and alkali discriminant diagram of host rock, Cenozoic basalt from the South China Sea belongs to intraplate alkali basalt. The results suggest that alkali basalt series in the study area may be the products of continuous evolution of mantle plume, which result from some physical and chemistry process including partial melting and fractional crystallization of mantle plume during the course of its ascent to the surface.