ELECTROCHEMICAL MECHANISM FOR FULLERENE FORMATION IN PLASMA ARCS

During the synthesis of fullerenes by dc plasma arcs, it has been found that the anodic graphite rod consistently burns up, while the cathodic graphite rod grows slag at its end. Further investigations revealed that the anodic and cathodic graphite rods p

一个先进的工业机器人计算机控制系统——ARCS

随着工业机器人及其应用的不断发展,要求一个强有力的计算机系统来控制它的工作,并具有灵活、方便的机器人编程语言.本文系统地介绍了我们自行设计并实现的一个先进的机器人控制系统——ARCS.该系统主要包括两部分:(1)一个实时多任务的机器人控制软件SVAL系统,该系统支持一种通用性较强的机器人编程语言——SVAL语言.(2)一个支持该软件系统工作的、具有开放式结构的硬件环境.ARCS系统具有良好的实时性、可扩展性及基于外部传感器信号进行控制的能力.由于该系统的开放式结构.使其根据不同要求可方便地增删其功能,并可控制不同类型的机器人.我们已成功地实现对PUMA760机器人的控制,并在其上引入了力觉与接近觉的传感器,采样时间可缩短到16ms.一年多的运行结果证明,该系统稳定可靠,性能良好,现在正向产品转化.

Carbon transition efficiency and process cost in high-rate, large-area deposition of diamond films by DC arc plasma jet

A new DC plasma torch in which are jet states and deposition parameters can be regulated over a wide range has been built. It showed advantages in producing stable plasma conditions at a small gas flow rate. Plasma jets with and without magnetically rotated arcs could be generated. With straight are jet deposition, diamond films could be formed at a rate of 39 mu m/h on Mo substrates of Phi 25 mm, and the conversion rate of carbon in CH4 to diamond was less than 3%. Under magnetically rotated conditions, diamond films could be deposited uniformly in a range of Phi 40 mm at 30 mu m/h, with a quite low total gas flow rate and high carbon conversion rate of over 11%. Mechanisms of rapid and uniform deposition of diamond films with low gas consumption and high carbon transition efficiency are discussed.

二次光栅在波前测量中的应用

采用一种特殊的二次光栅用于激光波前测量, 它对非零级衍射光束具有不同的聚焦效应, 其光栅线为圆弧型而非直线。导出了在会聚光束情况下的两平面成像在单一像平面上的距离关系, 实验上实现了二次光栅用于会聚光束的波前测量, 测量得到会聚光束具有较大的散焦(-2.93λ)和球差(1.34λ), 与该透镜引起波前的离焦像差理论理想值(-2.695λ)基本符合。该技术可以实现波前的高空间分辨力和高精度实时测量, 大大减少光学元件数量, 降低装置成本。由于大功率激光束的不稳定性, 其波前变化非常快, 所以该方法的实时性非

Ag surface plasmon enhanced double-layer antireflection coatings for GaAs solar cells

Surface plasmon enhanced antireflection coatings for GaAs solar cells have been designed theoretically. The reflectance of double-layer antireflection coatings (ARCs) with different suspensions of Ag particles is calculated as a function of the wavelength according to the optical interference matrix and the Mie theory. The mean dielectric concept was adopted in the simulations. A significant reduction of reflectance in the spectral region from 300 to 400 nm was found to be beneficial for the design of ARCs. A new SiO_2/Ag-ZnS double-layer coating with better antireflection ability can be achieved if the particle volume fraction in ZnS is 1%-2%.

An alternative approach to ascertain the rate-determining steps of TiO2 photoelectrocatalytic reaction by electrochemical impedance spectroscopy

In an attempt to ascertain the rate-determining steps (RDS) of TiO2 photoelectrocatalytic (PEC) reaction, the PEC oxidation of sulfosalicylic acid (SSA) solution in a TiO2-coated electrode reactor system was monitored by applying the electrochemical impedance spectroscopy (EIS) method. In the meantime, an EIS mathematical model was first established to theoretically simulate the PEC reaction. Based on the EIS model, the theoretical simulation indicates three typical reactions in a PEC oxidation process, which include the charge-transfer-dominated reaction, both the charge-transfer- and adsorption-dominated reaction, and the adsorption-dominated reaction. The experimental results of EIS measurement showed that there was only one arc/semicircle on the EIS plane display when the external bias applied was below 200 mV (vs SCE) in the SSA PEC degradation whereas there were two arcs/semicircles when the externally applied bias exceeded 200 mV (vs SCE). The experimental results have a good agreement with the model simulation. The EIS method in this study provides an easier way to determine the RDS in a PEC oxidation process, which would be helpful to better control the reaction in practice.

基于时间Petri网的制造过程模型研究

分析了时间Petri网的激发规则、托肯可用时间和抑制弧等特性,以及制造过程中随机故障的特征。提出不同的时间关联方式对应的多种建模方法,考虑不同的故障发现模式、不同的作业处理策略,建立相应的单机制造过程模型。在此基础上采用模块化和层次化方法可以构建复杂制造过程的时间着色Petri网模型,并可以转换成仿真模型,进一步分析随机机器故障对制造过程性能的影响。

中国东部沙地物源示踪及地质意义

Heavy mineral assemblages, chemical compositions of diagnostic heavy minerals such as garnet and tourmaline, and U-Pb ages and Hf isotopic compositions of zircons are very effective means to determine sediment provenance. An integrated application of the above provides insight on the lithologies, crystallization ages and crustal formation ages of the parent magma of sediment source areas. As a result, the locations and characteristics of potential source areas can be constrained and contributions of different source regions may be evaluated. In addition, the study provides evidence for the magmatic and tectonic history of source areas using a novel approach. The heavy mineral assemblages, and chemical compositions of detrital garnets and tourmalines, U-Pb ages and Hf isotopic compositions of zircons for sand and loess samples deposited since the Last Glacial Maximum (LGM) from the Hulunbeier, Keerqin and Hunshandake sandlands were analyzed and compared to those of central-southern Mongolia, the central Tarim and surrounding potential source areas, the Central Asian Orogenic Belt (CAOB) and North China Craton (NCC). The following remarks on provenance and tectonic history can be made: 1. The source compositional characteristics of the Hulunbeier, Keerqin and Hunshandake sandlands are similar. They are derived from the CAOB and NCC whose contributions for the Keerqin and Hunshandake sandland are about 50%. For the Hulunbeier sandland it is somewhat less, about 40%. 2. Loesses around of the sandlands have the identical source signiture as the sands, implying that they are sorted by the same wind regime. 3. The source characteristics of the present and LGM sands are the same, providing direct evidence that the present sands originated from the reworking of LGM sands. 4. The provenance characteristics of the three sandlands differ from those of the Tarim. As a result, the possibility that the three eastern sandlands were sourced from the Taklimakan desert can be ruled out. 5. The source compositions of sand samples derived from the CAOB indicate that the occurrence of Archean and Paleoproterozoic metamorphic basement rocks is limited and continuous subduction-accretion events from the Neoproterozoic to the Mesozoic occurred. This implies that the CAOB is a orogenic collage belt similar to the present day southwest-Pacific, and formed by the amalgamation of small forearc and backarc ocean basins occurring between island arcs and microcontinents during continuous collision and accretion. The Hf isotopic signitures of detrital zircons indicate that large amounts of juvenile mantle materials were added to the CAOB crust during the Phanerozoic.

边坡工程的极限分析上限法

Theory of limit analysis include upper bound theorem and lower bound theorem. To deal with slope stability analysis by limit analysis is to approximate the real solution from upper limit and lower limit. The most used method of limit analysis is upper bound theorem, therefore it is often applied to slope engineering in many cases. Although upper bound approach of limit analysis can keep away from vague constitutive relation and complex stress analyses, it also can obtain rigorous result. Assuming the critical surface is circular slip surface, two kinematically admissible velocity fields for perpendicular slice method and radial slice method can be established according to the limit analysis of upper bound theorem. By means of virtual work rate equation and strength reduction method, the upper-bound solution of limit analysis for homogeneous soil slope can be obtained. A log-spiral rotational failure mechanism for homogeneous slope is discussed from two different conditions which represent the position of shear crack passing the toe and below the toe. In the dissertition, the author also establishes a rotational failure mechanics with combination of different logarithmic spiral arcs. Furthermore, the calculation formula of upper bound solution for inhomogeneous soil slope stability problem can be deduced based on the upper bound approach of rigid elements. Through calculating the external work rate caused by soil nail, anti-slide pile, geotechnological grid and retaining wall, the upper bound solution of safety factor of soil nail structure slope, slip resistance of anti-slide pile, critical height of reinforced soil slope and active earth pressure of retaining wall can be obtained by upper bound limit analysis method. Taking accumulated body slope as subject investigated, with study on the limit analysis method to calculate slope safety factor, the kinematically admissible velocity fields of perpendicular slice method for slope with broken slip surface is proposed. Through calculating not only the energy dissipation rate produced in the broken slip surfaces and the vertical velocity discontinuity, but also the work rate produced by self-weight and external load, the upper bound solution of slope with broken slip surface is deduced. As a case study, the slope stability of the Sanmashan landslide in the area of the Three Gorges reservoir is analyzed. Based on the theory of limit analysis, the upper bound solution for rock slope with planar failure surface is obtained. By means of virtual work-rate equation, energy dissipation caused by dislocation of thin-layer and terrane can be calculated; furthermore, the formulas of safety factor for upper bound approach of limit analysis can be deduced. In the end, a new computational model of stability analysis for anchored rock slope is presented after taking into consideration the supporting effect of rock-bolts, the action of seismic force and fissure water pressure. By using the model, not only the external woke-rate done by self-weight, seismic force, fissure water pressure and anchorage force but also the internal energy dissipation produced in the slip surface and structural planes can be totally calculated. According to the condition of virtual work rate equation in limit state, the formula of safety factor for upper bound limit analysis can be deduced.

晚中生代松辽盆地形成的大地构造环境及成因机制

Directed by the theory of "Collision Tectonic Facies", the tectonic setting and dynamic mechanism of the formation of Songliao basin in late Mesozoic (J_3-K_1) are studied in the present thesis with the methods of petrology, petrochemistry, geochemistry and isotopic geochronology. The research contents in this paper include as followings. Firstly, the general tectonic frame is made up of different tectonic facies formed from Mid-late Proterozoic to Mesozoic, which are Huabei plate, the Chengde-Siziwangqi melange (Pz_1), the Wenduermiao magmatic arc (Pz_1), the Hegenshan-Chaogenshan melange (Pz_2), the accretion arec (Pz_1-P), the Raohe-Hulin melange (Mz), the magmatic arc (Mz) and the pull-apart basin on the magmatic arc (Mz). Secondly, the volcanic rock assemblages of Songliao basin and its adjacent area in late Mesozoic is the typical calc-alkaline of the magmatic arc. The types of volcanic rocks in the study area include basalts, basaltic andesites, andesites, dacites and rhyolites, and basic-intermediate volcanic rocks have higher alkalinity. The volcanic rock series in this area is the high-K calc-alkaline series. Thirdly, the total REE of volcanic rocks in Songliao basin and its adjacent area is higher than that of the chondrite. The pattern of the REE normalized by the chondrite shows the characteristics similar to that of the typical island arcs or the active continental margins in the earth, that is enrichment of LREE and depletion of Eu. The spider-diagram of the trace element normalized by the primitive mantle also expresses the similar features to that of the typical island arcs or the active continental margins, it has distinctive valleies of Nb, Ta, Sr, P, and Ti, as well as the peaks of La, Ce, Th, U, and K. The incompatible elements show that the high field strength elements, such as Nb, Ta, Ti, and P, are depletion while the low field strength elements, such as K, U, Pb, and Ba, are enrichment. These features are similar to those of orogenic volcanic rocks and imply the formation of the volcanic rocks in this area is related to the subduction. The degrees of both the enrichment of the HFS elements and depletion of the LFS elements become more obvious from basic to acid volcanic rocks, which suggests crustal contamination enhances with the magmatic crystallization and fractionation. The concentration of the compatible elements is W-shape, and anomalies in Cr and Ni suggest there is the contamination during the magmatic crystallization and fractionation. Fourthly, the isotopic age data prove the volcanic activity in the Songliao basin and its adjacent area started in the early-middle Jurassic, and ended in the end of the early Cretaceous-the beginning of the Cretaceous. The volcanism summit was the late Jurassic-the early Cretaceous (100 - 150Ma). Finally, the tectonic setting of volcanism in the late Mesozoic was magmatic arc, which originated the subduction of Raohe-Hulin trench to the northwest Asian plate. The subduction began in the middle Jurassic, and the collision orogenesis between the Sikhote-Alin arc and Asian continent was completed in the end of the early Cretaceous-the beginning of the late Cretaceous. The results of above tectonic processes were finally to format Nadanhada orogenic belt symbolized by the Raohe-Hulin suture or melange belt. The violently oblique movement of the Izanagi plate toward Asian plate in the late Mesozoic was the dynamic mechanism of above tectonic processes. At the same tome, the left-lateral strike-slip shear caused by the oblique movement of the Izanagi plate produced a series of strike-slip faults in east Asian margin, and the large scale displacements of these strike-slip faults then produced the pull-apart basing or grabens on the magmatic arc. Conclusively, the tectonic setting during the formation of the grabens of Songliao basin in the late Mesozoic was magmatic arc, and its dynamic mechanism was the pull-apart. In a word, there was a good coupling relation among the oblique subduction of the oceanic plate, collisional orogene between island arc and continental plate, strike-slip shear of the faults and the formation of the grabens in Songliao basin and its adjacent area in late Mesozoic. These tectonic processes were completed in the unoin dynamic setting and mechanism as above description.

阿尔金蛇绿混杂带构造岩石组合及其大地构造意义

The Alytn fault is a huge left-slip fault zone within the Asian continent, and locates such zone that is linked to main tectonic units in the western China, which makes it is very important to the tectonic framework and ore distribution in the western China. Selecting two ophiolite zones (namely Hongliugou-Lapeiquan ophiolite zone and Sulamutage ophiolite zone) respectively located within the southern and northern part of the Altyn fault and based on analysis of field geology characteristics and geochemistry, this paper recognized the rock types (mainly mafic and ultramafic rocks) within the melanges and subdivided each lithological unit based on tectonic environment. At last, this paper rebuilt the paleo-tectonic framework in the Alytn region by the method of tectonic facies and discussed its tectonic evolution with the theory of collision orogens. Combining former results with hard field observation and geochemical analysis, this paper acquired such recognitions to two ophiolte zones within the Altyn fault zone as follows: To the typical regions (Hongliugou, Lapeiquan, Mangya and Sulamutage) within the two ophiolte zones in the Altyn fault zone, this paper offered the field geology profiles. Field geology characteristics show that they are composed of melange bases (mainly abyssal flysch and carbonate rocks) and melange blocks from various tectonic environments, often with fault contact among each lithological units, belonging to typical ophiolitic melange zone. The ultramafic rocks outcropped at the Altyn region are all harzburgites. Remant grains of primary minerals have melted residual texture and elastic deformation texture under high temperature and pressure. The whole-rock analyses show their low TiO_2 contents (0.01～0.04%), low Al, Ca and high MgO contents and wide Mg~# range (89.35～95.57). Rare earth patterns have two types, namely tabacco pipe-shped and LREE-shaped, of which the former is often seen. The chondrite-nomalized Yb values of these analyses are all lower than 1. The spinels have low Ti and high Cr content and most spinels have Cr# higher than 60. All of the above characteristics show that the ultramafic rocks in the Altyn fault zone are components of metmorphic peridotites of ophiolite from depleted mantle source and most ophiolites from this zone belong to supra-subduction zone (SSZ) type ophiolite with a few mid-ocean ridge basalt (MORB) type. Geochemical analyses show that the melange blocks within the Altyn ophiolitic melange zone have different characteristics from various tectonic environments. This paper recognized such tectonic-lithological assemblages as mid-ocean basalts, oceanic island basalts, oceanic island arc tholeiites, island arc calalkaline basalts and island arc granites and inferred that these tectonic-lithological units respectively belongs to such tectonic units as ophiolites, oceanic islands and/or oceanic seamounts, oceanic island arc and a~creting arcs, which show these blocks from oceanic crust and subduction zone for the most part. For the Altyn ophiolites, the chronological data show they become new from the north to the south. Combined with the study on late slip of Altyn fault and North Qilianshan orogeny, the author inferred that the Altyn region had belonged to one part of the North Qilianshan accreting wedge-arc orogeny at paleozoic, and later huge left-slip made it locate modem site.