Strain Regularity and Stiffness Tensor of Reinforcers in Dense Particle Reinforced Composites

针对高体积份数、随机分布、等轴状颗粒增强复合材料 ,研究了材料的应变分布规律 ,给出了基体和增强体应变平均值与材料微观结构参数之间的定量关系。结果表明 ,除应变平均值外 ,应变涨落是影响刚度张量的另一个重要因素 ,研究了应变涨落与材料微观结构参数之间的关系 ,并推导出了复合材料的刚度张量。与实验结果和以往的理论比较 ,预测结果与实验结果吻合良好

Micro/Nanomechanical and Tribological Properties of thin Diamond-Like Carbon Coatings

The diamond-like carbon (DLC) films with different thicknesses on 9Crl8 bearing steels were prepared using vacuum magnetic-filtering arc plasma deposition. Vickers indentation. nanoin-dentation and nanoscratch tests were used to characterize the DLC films with a wide range of applied loads. Mechanical and tribological behaviors of these submicron films were investigated and interpreted. The hardnesses of 9Crl8 and DLC, determined by nanoindentation, are approximately 8GPa and 60GPa respectively; their elastic moduli are approximately 25OGPa and 600GPa respectively. The friction coefficients of 9Crl8, DLC. organic coating, determined by nanoscratch, are approximately 0. 35, 0. 20 and 0. 13 respectively. It is demonstrated that nanoindentation and nanoscratch tests can provide more information about the near-surface elastic-plastic deformation, friction and wear properties. The correlation of mechanical properties and scratch resistance of DLC films on 9Crl8 steels can provide an assessment for the load-carrying capacity and wear resistance

Factors Resulting In Micron Indentation Hardness Descending In Indentation Tests

Some factors that affect the experimental results in nanoindentation tests such as the contact depth, contact area, load and loading duration are analyzed in this article. Combining with the results of finite element numerical simulation, we find that the creep property of the tested material is one of the important factors causing the micron indentation hardness descending with the increase of indentation depth. The analysis of experimental results with different indentation depths demonstrates that the hardness decrease can be bated if the continuous stiffness measurement technique is not adopted; this indicates that the test method itself may also be one of the factors causing the hardness being descended.

Third harmonic enhancement due to Fano interference in semiconductor quantum well

We investigate the emission spectra of the semiconductor quantum well for few-cycle and sub-cycle pulse exciting. We find that Fano interference may induce third harmonic enhancement. Third harmonic enhancement varies with the magnitude and duration of the incident pulse, and may be enhanced by approximately one order of magnitude for the low intensity region of the sub-cycle incident pulse exciting.

Estimation of Transverse Thermal Conductivity of Doubly-periodic Fiber Reinforced Composites

For steady-state heat conduction a new variational functional for a unit cell of composites with periodic microstructures is constructed by considering the quasi-periodicity of the temperature field and in the periodicity of the heat flux fields. Then by combining with the eigenfunction expansion of complex potential which satisfies the fiber-matrix interface conditions, an eigenfunction expansion-variational method (EEVM) based on a unit cell is developed. The effective transverse thermal conductivities of doubly-periodic fiber reinforced composites are calculated, and the first-order approximation formula for the square and hexagonal arrays is presented,which is convenient for engineering application. The numerical results show a good convergency of the presented method, even through the fiber volume fraction is relatively high. Comparisons with the existing analytical and experimental results are made to demonstrate the accuracy and validity of the first-order approximation formula for the hexagonal array.

奇异摄动控制系统:理论与应用

系统地回顾了近年来奇异摄动控制技术的发展 ,主要包括线性奇异摄动系统的稳定性分析与镇定、最优控制、H∞ 控制 ,非线性奇异摄动系统的镇定、优化控制和基于积分流形的几何方法 ,以及奇异摄动技术在实际工业 ,例如机器人领域、航天技术领域和工程工业、制造业等中的成功应用 .并指出了这一领域进一步研究的方向