Material response and failure mechanism of unidirectional metal matrix composites under impulsive shear loading

The material response and failure mechanism of unidirectional metal matrix composite under impulsive shear loading are investigated in this paper. Both experimental and analytical studies were performed. The shear strength of unidirectional C-f/A356.0 composite and A356.0 aluminum alloy at high strain rate were measured with a modified split Hopkinson torsional bar technique. The results indicated that the carbon fibers did not improve the shear strength of aluminum matrix if the fiber orientation aligned with the shear loading axis. The microscopic inspection of the fractured surface showed a multi-scale zigzag feature which implied a complicated shear failure mechanism in the composite. In addition to testing, the micromechanical stress field in the composite was analyzed by the generalized Eshelby equivalent method (GEEM). The influence of cracking in matrix on the micromechanical stress field was investigated as well. The results showed that the stress distribution in the composite is quite nonhomogeneous and very high shear stress concentrations are found in some regions in the matrix. The high shear stress concentration in the matrix induces tensile cracking at 45 degrees to the shear direction. This in turn aggravates the stress concentration at the fiber/matrix interface and finally leads to a catastrophic failure in the composite. From the correlation between the analysis and experimental results, the shear failure mechanism of unidirectional C-f/A356.0 composite can be elucidated qualitatively.

A contact crack problem in an infinite plate

The problem of an infinite plate with crack of length 2a loaded by the remote tensile stress P and a pair of concentrated forces Q is discussed. The value of the force Q for the initial contact of crack face is investigated and the contact length elevated, while the Q force increases. The problem is solved assuming that the stress intensity factor vanishes at the end point of the contact portion. By the Fredholm integral equation for the multiple cracks, the reduction of stress intensity factor due to Q is found. (C) 1999 Elsevier Science Ltd. All rights reserved.

风沙二相流动的三流体模型

采用连续介质观点研究风沙运动,这一工作的关键在于如何正确地模化颗粒相的应力. 通过对气-固二相流研究中常用的双流体模型的分析,发现此模型在研究风沙运动时有相 当的缺陷,即使是研究最简单的风沙流——定常二维充分发展的流场也是如此.提出了将 向上、向下运动的颗粒用两种拟流体来表征的三流体模型.

Long pulsed laser induced reverse bulging and plugging

A new kind of failure mode is observed in circular brass foils whose peripheries are fixed and whose surfaces are subjected to a long pulsed laser over a central region. The failure is classified into three stages; they are referred to as thermal bulging, localized shear deformation and perforation by plugging. A distinct feature of the failure mode is that bulging and plugging occurred in the direction opposite to the incident laser beam. The failure mode is different from the well-known types of laser induced material damage, such as spallation, melting and/or vaporization.

Spectrophone measurements in sulfur-hexafluoride

The optoacoustic signal generated by pulsed 10.6 c infrared radiation incident upon a test cell filled with gaseous SF6 has been analyzed in detail. The effects ofm icroscopic energy transfer from the absorbing vibrational degrees of freedom, spontaneous emission, thermal conduction, and acoustic wave propagation are included. This complete treatment explains the experimental observations including a negative pressure response following irradiation at low gas pressure.

源于G.I.Taylor工作的现代经典物理学

一位科学家的工作提供了一门完整课程的素材，涉及从流体动力学稳定性、湍流到流体电动力学、微生物的运动．

生物素-亲和素微模式表面的制备与细胞定位

细胞在模式化表面的定位培养地于组织工程、生物传感器技术和细胞生物学基础研究具有重要意义。研究基于软光刻技术的生物素-亲和素微模式表面快速制备方法，并用所制备的模式进行牛主动脉血管内皮细胞的定位培养。表明该技术可在细胞尺度上有效地控制细胞生长的空间位置。

Post-cyclic Strength Degradation of Undisturbed and Remolded Marine Silty Clay

A series of static and cyclic-static tri-axial compression tests under consolidated-undrained conditions are carried out to study the characteristics of post-cyclic strength of the undisturbed and the remolded samples of marine silty clay. It is found that the post-cyclic monotonic strength decreases if the cyclic strain or pore pressure is over a certain value. The maximum degradation is 10% for undisturbed samples while 70% for remolded ones. The relationship between normalized undrained shear strength and apparent overconsolidation ratio, which is determined by the excess pore pressure induced by cyclic loading, is also established. Static consolidated-undrained tests on overconsolidated remolded samples are also performed. It is proposed that the static consolidated-undrained tests may be substituted for the cyclic-static consolidated-undrained tests if the post-cyclic strength degradation of remolded silty clay is needed to be evaluated simply.

A comparative study of Young's modulus of single-walled carbon nanotube by CPMD, MD, and first principle simulations

Carbon nanotubes (CNTs), due to their exceptional magnetic, electrical and mechanical properties, are promising candidates for several technical applications ranging from nanoelectronic devices to composites. Young's modulus holds the special status in material properties and micro/nano-electromechanical systems (MEMS/NEMS) design. The excellently regular structures of CNTs facilitate accurate simulation of CNTs' behavior by applying a variety of theoretical methods. Here, three representative numerical methods, i.e., Car-Parrinello molecular dynamics (CPMD), density functional theory (DFT) and molecular dynamics (MD), were applied to calculate Young's modulus of single-walled carbon nanotube (SWCNT) with chirality (3,3). The comparative studies showed that the most accurate result is offered by time consuming DFT simulation. MID simulation produced a less accurate result due to neglecting electronic motions. Compared to the two preceding methods the best performance, with a balance between efficiency and precision, was deduced by CPMD.

Energy spectrum of fermionized bosonic atoms in optical lattices

We investigate the energy spectrum of fermionized bosonic atoms, which behave very much like spinless noninteracting fermions, in optical lattices by means of the perturbation expansion and the retarded Green's function method. The results show that the energy spectrum splits into two energy bands with single-occupation; the fermionized bosonic atom occupies nonvanishing energy state and left hole has a vanishing energy at any given momentum, and the system is in Mott-insulating state with a energy gap. Using the characteristic of energy spectra we obtained a criterion with which one can judge whether the Tonks-Girardeau (TG) gas is achieved or not.

空变菲涅耳联合变换相关器

提出了菲涅耳联合变换相关器（Fresnel Joint Trans form Correlator，FnJTC）结构，给出了数学推导过程，并通过计算机模拟验证了可行性及其与传统相关器所不同的相关特性。在相关过程第一阶段中，菲涅耳联合变换相关器对输入的联合图像作菲涅耳变换，代替了传统联合变换相关器（JTC）的傅里叶变换。与传统相关器相比，菲涅耳联合变换相关器是空变系统，相关峰值依赖于输入参考图像与目标图像的相似性、两图像之间的相对位置及参考图像（或目标图像）的线性相位调制。

棱镜自重变形对波面影响的研究

采用有限元方法分析了单棱镜在重力作用下三个典型位置的表面变形，对棱镜表面φ425nm通光孔径轴向变形量进行Zernike多项式拟合，画出了相应的波差图，并确定设计方案．进一步选择φ360mm口径光束对双棱镜在几种典型相对位置下进行光线采样、追迹，计算得到不同情况下由于双棱镜自重变形引起的总波差．

飞秒激光辐射下微突起结构形成的超快热弹性模拟

本文结合有限元方法和超快热弹性模型对飞秒激光辐射下形成的微突起结构进行了数值模拟研究。模拟结果表明微突起结构的形成与入射飞秒激光的参数以及材料的热弹性质有关。在圆锥状微突起结构的形状和高度方面，实验结果与模拟结果呈现良好的一致性，这也从实验上表明了超快热弹性模型的有效性。本文的研究将有助于利用超快激光对薄膜材料进行纳米构造。

2-氨基-6-乙氧基苯并噻唑类偶氮染料及其金属鏊合物的合成及光学热学性能研究

合成了2-（2-氨基-6-乙氧基苯并噻唑基偶氮）-5-（N,N-二乙基氨基）三氟甲基磺酰苯胺偶氮染料（EBTDATFS）及其与乙酸镍、乙酸钴、乙酸铜、乙酸锌等金属盐鏊合的金属鏊合物。通过红外光谱、紫外-可见吸收光谱和MALDI质谱等对染料及其金属鏊合物进行了结构表征;使用旋涂方法在K9玻璃和抛光的单晶硅基片上制备薄膜;研究了镍金属鏊合物的热学性能;使用椭偏仪研究了Ni和Zn鏊合物的光学常数。结果表明：4种金属鏊合物薄膜最大吸收光谱为621-629nm,且长波边吸收峰陡峭;TGA-DSC测试结果表明镍金属鏊